User manual MICROTEK C593

C593 15" LCD MONITOR USER'S MANUAL Installing The Monitor Follow these steps to install the monitor, 1. Before you connect the cables,make sure that the monitor and the system unit power switches are OFF. Please follow the following drawing to remove the plastic back over in order to connect the signal cable and power cable. Plug one end of the 15pin signal cable to the monitor and the other end to the video signal connector at the rear of the system. Tighten the two screws on the cable connector on both ends, otherwise the screen will be abnormal and LED light is yellow color, not the normal green color. Connect the power to the monitor through the AC/DC adapter. Connect the power cord on the AC outlet, see the below. 2. 3. 4. 5. ii Content Operating Instructions ............................................................................ iv Safety Precautions ................................................................................... v Care and Maintenance ........................................................................... vi Control Functions ..................................................................................... 1 Adjustment Procedure ............................................................................. 2 Auto-Adjustment .............................................................................. 2 RGB Adjustment ................................................................................ 3 Contrast Value Adjustment ........................................................ 3 Color Balance ............................................................................. 3 Geometry Adjustment ...................................................................... 4 Vertical & Horizontal Position Adjustment ................................ 4 Viewer Screen Size Adjustment ............................................... 4 Phase Adjustmentt ..................................................................... 4 Multilanguage Support ..................................................................... 5 DOS Txt/GFX. .................................................................................... 5 Color Temperature ............................................................................ 5 Brightness Adjustment ..................................................................... 5 Understanding the Display Resolution Setting ............................... 5 General Specifications ............................................................................. 6 General Performance .............................................................................. 7 iii Operating Instructions Thank you for purchasing this high-resolution multi-scan color monitor. Please read this guide thoroughly before installation. FCC RADIO FREQUENCY INTERFERENCE STATEMENT WARNING: (FOR FCC CERTIFIED MODELS) This monitor has been tested and found compliant with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide proper protection against harmful interference to a residential installation. This monitor generates, uses, and can radiate radio frequency energy. Harmful interference to radio communication may result if it is not properly installed and used. However, there is no guarantee that interference will not occur in a particular installation. If this monitor does cause serious interference to radio or television reception, resetting the monitor may resolve the problem. Moreover, users are encouraged to correct interference by doing one or more of the following: · · · · Reorient or relocate the receiving antenna. Move the monitor and the receiver further away from each other. Connect the monitor into an outlet on a circuit different from that to which the receiver is connected. Consult your local dealer or a qualified technician. FCC Warning: To assure a continued FCC compliance, a user must use a grounded power supply cord and the provided shielded video interface cable with bonded ferrite cores. Also, any unauthorized changes or modifications to this monitor will void the user's authority to operate this device. Note: If necessary, shielded interface cables and the A.C. power cord must be used to meet the emission level limits. EMI Certification The Class B digital apparatus meets all requirements of the Canadian InterferenceCausing Equipment Regulation. Cet appareil numerique de class B respecte toutes les exigences du Reglement sur Ic materiel brouilleur du Canada. iv Safety Precautions This monitor is manufactured and tested on the ground principle that a user's safety comes first. However, improper use or installation may not only damage the monitor but endanger the user as well. As a safety precaution, go over the following WARNINGS carefully before installation, and keep this guide handy. Warnings: · This monitor should be operated only at the correct power sources indicated on the label at the rear end of the monitor. If you are unsure of the power supply in your residence, consult your local dealer or Power Company. Do not try to repair the monitor yourself, as it contains no user-serviceable parts. The monitor should only be repaired by a qualified technician. Do not remove the monitor cabinet. There are high-voltage parts inside that may cause electric shock to human bodies, even when the power cord is disconnected. Stop using the monitor if the cabinet is damaged. Have it checked by a service technician. Put your monitor only in a clean, dry environment. Unplug the monitor immediately if it gets wet, and consult your service technician. Always unplug the monitor before cleaning it. Clean the cabinet with a clean, dry cloth. Apply non-ammonia-based cleaner onto the cloth, not directly onto the glass screen. Keep the monitor away from magnetic objects, motors, TV sets, and transformers. Do not place heavy objects on the cable or power cord. For PLUG CABLE EQUIPMENT, the socket outlet should be installed near the equipment and should be easily accessible. · · · · · · · · v Care and Maintenance Care · · · · Avoid exposing your monitor directly to sunlight or other heat sources. Place your monitor away from the sun to reduce glare. Put your monitor in a well-ventilated area. Do not place anything heavy on top of your monitor. Make certain that your monitor is installed in a clean and moisture-free area. Keep your monitor away from magnets, motors, transformers, speakers, and TV sets. SafetyTips · · If smoke, abnormal noise or odor comes out of your monitor, switch off the power immediately and call your service center. Never remove the rear cover of your monitor cabinet. The display unit inside contains high-voltage parts and may cause electric shock to human bodies. Never try to repair the monitor yourself. Always call your service center or a qualified technician to fix it. · Note: This user's manual contains graphics and information that is for reference purposes only and is subject to change without notice. vi Control Functions The Monitor control functions are located on the lower center portion of the front panel. These are shown in the figure below and described in the following paragraphs. 1. : Power switch Use the power switch to turn power ON or OFF. We recommend turning your system power on first, then the LCD monitor 2. - & + : Decrement & Increment These two keys are used to decrease or increase the values of each selected item. 3. Selection: Down key This key is used to select the wanted adjustment item. It always move down to the next item. 4. Menu Press the Menu key to activate the on-screen display. This is a toggle key, so press twice to turn off the on-screen display. After 30 seconds of idle time, the OSD screen will automatically turn off. 5. Auto adjustment Press this key to get better visual performance. 1 Adjustment Procedure 1. Press the Menu key to activate the OSD screen. The screen below will appear. Note: Perform the procedure above whenever you need to change a setting. For the succeeding sections, this step will not be included, and users will be presumed to have performed the procedure. OSD SCREEN 1024X768 75Hz/60KHz AUTO ADJUSTMENT MENU MENU LANGUAGE DOS/GFX MENU OFF USER 100 VERSION XGAD9B11-5100 2. 3. Use the selection key to move to the desired item. Use the - & + key to carry out the desired function or to go to the second menu item and perform further changes. Auto-Adjustment We strongly recommend that you use this item to get the optimized visual quality. Use the selection key to select auto-adjustment, then press - or + to get the optimized quality. 2 RGB Adjustment Use the selection key to select the icon, then press - or +. The screen below will appear. 1024X768 Auto-Balance CONTRAST RED GREEN BLUE BALANCE RED GREEN BLUE 75 Hz/60 KHz 20 18 19 49 50 26 VERSION XGAD9B11-5100 Contrast Value Adjustment Use the selection key to select the CONTRAST field, then press - & + to get the best contrast optimization. You can adjust R,G,B simultaneously or adjust each Red, Green, and Blue channel separately. You can also use this field to change purity of the RGB levels. Color Balance Use the selection key to select the COLOR BALANCE field, then press - & + to get the best color balance effect or to separately set the RGB color values. You can also use this field to change intensity of the RGB levels. The easiest way to adjust the contrast and color balance setting is to use auto-balance. 3 Geometry Adjustment Use the selection key to select the icon, then press - & +. The screen below will appear. 1024X768 75 Hz/60 KHz 21 33 1344 49 PHASE VERSION XGAD9B11-5100 If you need to go back to the previous OSD menu screen, press the MENU key. Vertical & Horizontal Position Adjustment 1. Use the selection key to move to the icon, then press - & + to move the whole screen left or right to the center position. Use the selection key to move to the icon, then press - & + to move the whole screen down or up to the center position. 2. Viewing Screen Size Adjustment Use the selection key to move to the icon, then press - & + to get the larger viewing size. Phase Adjustment You can adjust phase tracking of the display signal to reduce display flicker. An invalid phase tracking will cause unstable and flicking display. Use the selection key to move to the Phase item, then press - & + to get better image quality. 4 Multi-language support You can select five OSD languages for your convenience. 1024X768 English German French Italian Spanish VERSION 75 Hz/60 KHz XGAD9B11-5100 DOS Txt/GFX You can select display mode as 640 x 400 (graphic mode) or 720 x 400 (text mode). Color Temperature Three modes are provided: User Mode, 6500, and 9300. Use the selection key to select the Color Temperature field, then press - & + to select the color temperature setting. Brightness Adjustment Use the selection key to select the Brightness field, then press - & + to change the brightness value. Understanding the Display Resolution Setting In the OSD screen, you will see the Horizontal frequency (HF), Vertical frequency (VF), display resolution (MODE) and the monitor Firmware version (ROM LEVEL). These values are automatically detected by the monitor, and the settings cannot be changed by the user. 5 General Specifications LCD type: Input Signal: Screen area: Dot Pitch: Scanning frequency: Resolution: Refresh Rate: Display Color: Luminance: Contrast Ratio: Response Time: Rising time: Falling time: View Angle (CR>10): Control Type: Plug & Play: Audio: Dimension (mm) Panel (H x W): Overall (H x W x D): Net weight: Tilt: AC Input: Power Management: Power Consumption: Regulatory Compliance: Ambient Temperature: Humidity (Relative): 15.0" XGA Color TFT Analog (0.7Vp-p/75 ohm positive) 304.1 mm x 228.1 mm 0.297 mm (H) 31.46 KHz-60 KHz , (V) 60 Hz-75 Hz 1024 x 768 80 MHz (maximum) 16.2M colors (dithering) 200 cd/m2 (Typ.) 350 (Typ.) Typ. 7 ms 23 ms OSD VESA DDC1/2B Not available 304.128 x 228.96 mm (Please include inches for U.S) 357.5 x 375 x 1 18.3 mm (include Inches) 5.0 kg (include weight in pounds) Up 30° / Down 5° AC 110 V ~ 240 V (48-62 Hz) VESA DPMS 30 W FCC Class B, CE 0° ~ 45° (operating), -20° ~ 60° (storage) (include temperature in Fahrenheit) 10 ~ 85% non-condensing (operating) 10 ~ 95% non-condensing (storage) Max (10% ~ 90% ) 22 ms 38 ms Horizontal: 120 (Typ.), Vertical: 100 (Typ.) 6 General Performance Preset timing is shown as follows: Resolution 640 x 480 640 x 480 640 x 480 800 x 600 800 x 600 800 x 600 800 x 600 1024 x 768 1024 x 768 1024x768 720 x 400 640 x 350 640 x 400 1024 x 768 H/V Frequency 60Hz/31.47KHz 72Hz/37.86KHz 75Hz/37.5KHz 56.3Hz/35.16KHz 60.3Hz/37.88Khz 72.2Hz/48/08KHz 75Hz/46.87KHz 60Hz/48.36KHz 70Hz/56.47KHz 75Hz/60Khz 70Hz/31.47KHz 70Hz/31.47Khz 70Hz/31.47KHz 74.9Hz/60.2KHz CLK count of H period 800 832 840 1024 1056 1040 1056 1344 1328 1312 900 800 800 1328 7