User manual MITSUBISHI LVP-X80U

LCD Projector User Manual X80 MODEL LVP-X80U EN ­ 1 ESPAÑOL ITALIANO DEUTSCH FRANÇAIS ENGLISH CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION: TO PREVENT ELECTRIC SHOCK, DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE. NOTE: SINCE THIS PROJECTOR IS PLUGGABLE EQUIPMENT, THE SOCKET-OUTLET SHALL BE INSTALLED NEAR THE EQUIPMENT AND SHALL BE EASILY ACCESSIBLE. WARNING Use the attached specified power supply cord. If you use another power-supply cord, it may cause interference with radio and television reception. Use the attached RGB cable, RS-232C cable with this equipment so as to keep interference within the limit of a FCC Class A device. This apparatus must be grounded. The projector automatically shuts off when the lamp is used up in about 2,000 hours and cannot be used until the lamp is replaced and the internal timer is reset. See page 23. DO NOT LOOK DIRECTLY INTO THE LENS WHEN PROJECTOR IS IN THE POWER ON MODE. When using the projector in Europe COMPLIANCE NOTICE This LCD - Video Projector complies with the requirements of the EC Directive 89/336/EEC "EMC Directive" as amended by Directive 93/68/EEC and 73/23/EEC "Low Voltage Directive" as amended by Directive 93/68/EEC. The electro-magnetic susceptibility has been chosen at a level that gains proper operation in residential areas, on business and light industrial premises and on small-scale enterprises, inside as well as outside of the buildings. All places of operation are characterised by their connection to the public low voltage power supply system. WARNING Use the attached RGB cable or RS-232C cable with this equipment so as to keep interference within the limits of a EN55022 Class B and EN55013. Please follow WARNINGS instructions. EN ­ 2 Contents Important safeguards ...........................................................................4 Overview ............................................................................................... 6 Using the remote control ......................................................................8 Battery installation ......................................................................................................... 8 Installation ............................................................................................9 Basic connections ............................................................................... 10 Projector + AV equipment............................................................................................. 10 Projector + DVD player or HDTV decoder ................................................................... 10 Projector + personal computer ...................................................................................... 11 Preparing the projector for operation ............................................... To operate projector power ON .......................................................... Menu operation .................................................................................. Picture adjustment ............................................................................. 12 13 15 18 Specification of RGB signals in each computer mode of the projector ....................... 20 Advanced feature for presentation .................................................... 21 Expand ........................................................................................................................... PinP (Picture in Picture) ............................................................................................... Still ................................................................................................................................. Mouse remote control .................................................................................................... 21 21 21 22 Lamp replacement ............................................................................. Maintenance ....................................................................................... Troubleshooting .................................................................................. Indicators ............................................................................................ Specifications ...................................................................................... 23 24 25 26 27 27 28 28 28 28 Kensington Lock ............................................................................................................ Connectors ..................................................................................................................... Dimensional drawings .................................................................................................. What's included in the box ............................................................................................ Replacement part .......................................................................................................... Trademark, Registered trademark Macintosh is registered trademark of Apple Computer Inc. IBM and VGA are trademarks or registered trademarks of International Business Machines Corporation. MicroSaver and Kensington are registered trademarks of Kensington Technology Group. Other brand or product names are trademarks or registered trademarks of their respective holders. B EN ­ 3 ENGLISH Important safeguards Please read all these instructions regarding your LCD projector and retain them for future reference. Follow all warnings and instructions marked on the LCD projector. 1. Read instructions All the safety and operating instructions should be read before the appliance is operated. Retain instructions The safety and operating instructions should be retained for future reference. Warnings All warnings on the appliance and in the operating instructions should be adhered to. Instructions All operating instructions must be followed. Cleaning Unplug this projector from the wall outlet before cleaning it. Do not use liquid aerosol cleaners. Use a damp soft cloth for cleaning. Attachments and equipment Never add any attachments and/or equipment without the approval of the manufacturer as such additions may result in the risk of fire, electric shock or other personal injury. Water and moisture Do not use this projector near water or in contact with water. Accessories Do not place this projector on an unstable cart, stand, tripod, bracket or table. Use only with a cart, stand, tripod bracket, or table recommended by the manufacturer or sold with the projector. Any mounting of the appliance should follow the manufacturer's instructions and should use a mounting accessory recommended by the manufacturer. 14. 10. Power sources This projector should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power, please consult your appliance dealer or local power company. Power-cord protection Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them. Pay particular attention to cords at plugs, convenience receptacles, and points where they exit from the appliance. Do not put the power cord under a carpet. Overloading Do not overload wall outlets and extension cords as this can result in a fire or electric shock. Objects and liquids Never push objects of any kind through openings of this projector as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the projector. Servicing Do not attempt to service this projector yourself. Refer all servicing to qualified service personnel. Damage requiring service Unplug this projector from the wall outlet and refer servicing to qualified service personnel under the following conditions: (a) If the power-supply cord or plug is damaged. (b) If liquid has been spilled, or objects have fallen into the projector. (c) If the projector does not operate normally after you follow the operating instructions. Adjust only those controls that are covered by the operating instructions. An improper adjustment of other controls may result in damage and may often require extensive work by a qualified technician to restore the projector to its normal operation. (d) If the projector has been exposed to rain or water. (e) If the projector has been dropped or the cabinet has been damaged. (f) If the projector exhibits a distinct change in performance - this indicates a need for service. Replacement parts When replacement parts are required, be sure that the service technician has used replacement parts specified by the manufacturer or parts having the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock or other hazards. Safety check Upon completion of any service or repair to this projector, ask the service technician to perform safety checks determining that the projector is in a safe operating condition. 11. 2. 3. 12. 4. 5. 13. 6. 7. 15. 8. An appliance and cart combination should be moved with care. Quick stops, excessive force and uneven surfaces may cause the appliance and cart combination to overturn. 9. Ventilation Slots and openings in the cabinet are provided for ventilation, ensuring reliable operation of the projector and to protect it from overheating. Do not block these openings or allow them to be blocked by placing the projector on a bed, sofa, rug, or bookcase. Ensure that there is adequate ventilation and that the manufacturer's instructions have been adhered to. 16. 17. EN ­ 4 Do not operate if smoke, strange noise or odor comes out of your projector. It might cause fire or electric shock. In this case, unplug immediately and contact your dealer. Do not touch them or put other equipment in front of Air outlet grill. The heated Air outlet grill and Bottom plate may cause injury or damage to other equipment. Also, do not set the projector on the desk which is easily affected by heat. Never remove the cabinet. This projector contains high voltage circuitry. An inadvertent contact may result in an electric shock. Except as specifically explained in the Owner's Guide, do not attempt to service this product yourself. Please contact your dealer when you want to fix, adjust or inspect the projector. Clean the air-filter once a month. Clean the air-filter frequently. If the filter or ventilation slots become clogged with dirt or dust, the temperature inside of the projector may rise and cause some troubles, such as damage of inside parts, and shortening the life of panel. Place of installation For safety's sake, refrain from setting the projector at any place subjected to high temperature and high humidity. Please maintain an operating temperature, humidity, and altitude as specified below. · Operating temperature: between +41°F (+5°C) and +95°F (+35°C) · Operating humidity: between 30 and 90% · Never put any heat-producing device under the projector so that the projector does not overheat. · Do not attach the projector to a place that is unstable or subject to vibration. · Do not install the projector near any equipment that produces a strong magnetic field. Also refrain from installing near the projector any cable carrying a large current. · Place the projector on a solid, vibration free surface: otherwise it may fall, causing serious injury to a child or adult, and serious damage to the product. · Do not stand the projector: it may fall, causing serious injury and damage to the projector. · Place the projector within a slope of ±15°. Slanting the projector more than ± 15° may cause trouble or explosion of the lamp. · Do not place the projector near air-conditioning unit or heater to avoid hot air to the exhaust and ventilation hole of the projector. Do not modify this equipment. It can lead to fire or electric shock. If you break or drop the cabinet. Do not keep using this equipment if you break or drop it. Unplug the projector and contact your dealer for inspection. It may lead to fire if you keep using the equipment. Do not face the projector lens to the sun. It can lead to fire. Use correct voltage. If you use incorrect voltage, it can lead to fire. Do not place the projector on uneven surface. Place the projection on a leveled and stable surface only. Please do not place equipment on unstable surfaces. Do not look into the lens when it is operating. It may hurt your eyes. Never let children look into the lens when it is on. Do not turn off the main power abruptly or unplug the projector during operation. It can lead to lamp breakage, fire, electric shock or other trouble. It is best to wait for the fan to turn off before turning main power off. COMPLIANCE NOTICE OF FCC This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus as set out in the interference-causing equipment standard entitled "Digital Apparatus", ICES-003 of the Department of Communications. Changes or modifications not expressly approved by Mitsubishi could void the user's authority to operate this equipment. COMPLIANCE NOTICE OF INDUSTRY CANADA This Class A digital apparatus complies with Canadian ICES-003. EN ­ 5 ENGLISH WARNING: Unplug immediately if there is something wrong with your projector. Do not touch Air outlet grill and Bottom plate which becomes hot. Overview 10 9 7 8 6 5 1 2 3 4 Air inlet grill (Front) Front height adjuster button Air inlet grill (Side) Terminal board Speaker Remote control sensor (Front) Zoom ring Focus ring Control panel Lens Kensington Security Lock Standard connector 12 Remote control sensor (Rear) 13 Air outlet grill 1 2 3 4 5 6 7 8 9 10 1 1 12 11 13 Control panel 12 11 10 9 8 AUTO POSITION POWER COMPUTER MUTE 1 LAMP VOLUME TEMP SOURCE VIDEO MENU ENTER 7 6 1 2 3 4 5 6 7 8 9 10 1 1 12 LAMP indicator TEMP (temperature) indicator + , ­ (VOLUME) button VIDEO button MENU button ENTER button Direction buttons MUTE button AUTO POSITION button COMPUTER button Power button Power indicator 2 3 4 5 Terminal board 1 2 3 Ground terminal Power jack Main power I : ON O : OFF 98 7 6 54 4 5 6 7 8 9 COMPUTER OUT USB RS-232C COMPUTER IN VIDEO IN VIDEO AUDIO L (MONO) O S-VIDEO AUDIO R AC IN 1 EN ­ 6 I MAIN 3 2 Video/audio input terminals Reset button COMPUTER IN terminal (D-SUB mini 15P) COMPUTER OUT terminal (D-SUB mini 15P) RS-232C (DIN 8P) terminal USB terminal Bottom side 3 1 2 3 Adjustment foot (right and left) Lamp cover Adjustment foot (up and down) Caution: Do not replace the lamp right after using the projector. The lamp is very hot. 2 1 Remote control 1 2 3 4 13 5 R-CLICK POWER MUTE 16 15 14 SOURCE KEYSTONE MOUSE LASER 6 MENU ENTER AUTO POSITION STILL 12 11 10 AVOID EXPOSURE -LASER RADIATION IS EMITTED FROM THIS APERTURE. 7 8 9 1 2 3 4 5 6 7 8 9 10 1 1 12 13 14 15 16 17 18 · Transmitter indicator Power button SOURCE button Mouse button Right click button (For mouse) MENU button AUTO POSITION button PinP button + , ­ (VOLUME) buttons EXPAND button STILL button ENTER button Mouse pointer / Direction buttons LASER button KEYSTONE button MUTE button Laser aperture Left click button (For mouse) When pressing Mouse button, it illuminates and Direction buttons work as the mouse pointer. Press the Mouse button or MENU button to set off. (Direction buttons work as Direction buttons.) Pressing LASER button emits the laser beam about 1 minute. Release LASER button and press it again if you wish to emits the laser beam. P in P EXPAND ­ VOLUME + · 17 About laser beam This remote control is class 2 (max. output 1 mW laser diode 640 - 660 nm) laser equipment. Beam Divergence : 3m distance about 5.0mm x 3.0mm (±1.5mm) 18 CAUTION LASER RADIATION DO NOT STARE INTO BEAM WAVE LENGTH : 640 - 660 nm MAX OUTPUT : 1 mW CLASS 2 LASER PRODUCT IEC 60825-1:1993+A1:1997 CAUTION : · Pressing the LASER button provided remote control emits laser beam. Do not look into the beam light directly. Do not point the laser beam at people. Looking the laser beam directly may damage eyesight. · Use of controls or adjustments or procedures other than those specified herein may result in hazardous radiation exposure. EN ­ 7 ENGLISH Using the remote control Battery installation Use two AAA size batteries. 1. Remove the back cover of the remote control by pushing the battery compartment door in the direction of the arrow. 2. Load the batteries making sure that they are positioned correctly (+ to +, and - to -). · Load the batteries from - spring side, and make sure to set them tightly. 3. Replace the back cover. 1 2 3 Important: · Do not combine a new battery with an old one. · Load batteries in the correct position. · Do not heat, take apart, or throw batteries into fire. · Do not try to recharge batteries. Do not use rechargeable batteries. · If the solution of batteries comes in contact with your skin or clothes, rinse with water. If the solution comes in contact with your eyes, rinse them with water and then consult your doctor. Operation area The range for operation is about 10 m (33 feet) when the remote control points to the projector. The distance to the screen back to the projector must be less than 6 m (20 feet). Depending on the type of the screen, the distance is different. 20° 15° 20° 15° 30° 30° Important: Avoid the direct sunlight or fluorescent light to the remote control sensor. Also keep the distance of more than 2 m between the remote control sensor and fluorescent lamp on the remote control may not work correctly. EN ­ 8 Installation Orientation of the projector Picture size can be set by changing the distance between the screen and the projector. Front projection To find the approximate distance between the projector and screen: Width Multiply the width of the screen Screen 1.9 (min.) , Multiply the width of the A B screen 2.5 (max.). · Refer to the chart for recommended Screen distances in maximum zoom and minimum zoom. Height A=B the screen and L (between of the projector) the head Screen Diagonal size (inch) 40 " 60 " 80 " 100 " 120 " 140 " 160 " 180 " 200 " 250 " 300 " Height inches Width feet (inch) (inch) 24 " 32 " 36 " 48 " 48 " 64 " 60 " 80 " 72 " 96 " 84 " 112 " 96 " 128 " 108 " 144 " 120 " 160 " 150 " 200 " 180 " 240 " Distance from screen (L) / (approximate) Maximum Minimum zoom (WIDE) zoom (TELE) (cm) (inch) (cm) (inch) 155 61 " 201 79 " 236 93 " 304 120 " 317 125 " 408 161 " 398 157 " 512 201 " 479 189 " 615 242 " 560 221 " 719 283 " 641 252 " 822 324 " 722 284 " 926 365 " 803 316 " 1030 405 " 1006 396 " 1288 507 " 1208 476 " ­ ­ Height projected image (H) (cm) 6.1 9.1 12.2 15.2 18.3 21.3 24.4 27.4 30.5 38.1 45.7 (inch) 2.4 " 3.6 " 4.8 " 6.0" 7.2 " 8.4 " 9.6 " 10.8 " 12.0 " 15.0 " 18.0 " · The above numbers are approximate, and may be slightly different from the actual measurements. Ceiling mount, Rear projection Ask a specialist for installation. For more details, consult your dealer. Caution: · Placing the projector on a carpet reduces ventilation from the fan at the bottom and might cause problems. Place a hard board or similar item under the projector to facilitate ventilation of the unit. · Place the projector more than 50 cm (20 inch) from the wall to prevent blocking the intake, exhaust slots and ventilation of this projector because hot air comes out of it. · Do not use the projector under the following circumstances, which may cause fire or electric shock. · in a dusty or humid place · while the projector is lying sideways or upside down · near a heater · in a kitchen or oily, smoky or damp place · in direct sunlight · with high temperature, such as a closed car · where the temperature is lower than 41°F or higher than 95°F Important: · Do not add stress on the lens, as this may cause damage. ´ EN ­ 9 ENGLISH H Basic connections This projector can be connected to equipment such as PC, VCRs, video cameras and DVD players. Important: · Make sure that your equipment is turned off before connection. · Plug in firmly and unplug by holding the plug, not by pulling the AC power cord. · If connected units are set too close to one another, the image may be affected. · Refer to the user manual of each component for details of connections. Projector + AV equipment Important: · Match the color of video and audio plugs on the AV cable with the connections. · S-video signals take priority over video signals. If you input both S-video signals and normal video signals at the same time, the normal video input automatically is inhibited. Connect either one of these. Ferrite core COMPUTER OUT RS-232C VIDEO IN VIDEO AUDIO L (MONO) COMPUTER IN O S-VIDEO AUDIO R AC IN VCR etc. · Speaker output is mono. · Select AUDIO MODE VIDEO to hear and to sound for the VIDEO. (Refer to page 16). · When connecting audio output of equipment which audio output is mono, connect to audio input L terminal. Projector + DVD player or HDTV decoder Some DVD players have output terminal for 3 line fitting (Y, CB, CR). When connecting them to the projector, connect to COMPUTER IN of the projector. DVD player generally has SDTV system component video output (Y, CB, CR) terminals. HDTV decoder has HDTV system component video output (Y, PB, PR) terminals. When connecting the projector with DVD player or HDTV decoder, the signal cuircuit automaticaly applied to either of them. In this case, the COMPUTER INPUT in the SIGNAL menu becomes [Y, CB, CR/Y, PB, PR]. DVD player or HDTV decoder AUDIO cable to AUDIO IN Y CB(PB) CR(PR) to AUDIO OUT BNC - RCA connector (optional) No connection G B R HD/CS VD COMPUTER OUT RS-232C COMPUTER IN VIDEO IN VIDEO AUDIO L (MONO) AUDIO R AC IN Mini D-SUB 15 pin-BNC conversion cable (optional) to COMPUTER IN · · · · · Y, PB, PR is an example of the terminal names for a HDTV decoder. The terminal name is different depending on the connected equipment. Use mini D-SUB 15 pin-BNC conversion cable for connection. Some DVD players may not project the image correctly. When connecting with HDTV equipment which has R, G, B output, set RGB for the COMPUTER INPUT in the SIGNAL setting menu. · Change the setting in the SIGNAL menu, when 525p signal is inputted. (Refer to page 20). EN ­ 10 O S-VIDEO I I MAIN to S-video input to video input to audio input to audio output to video output to S-video output MAIN Projector + Personal computer ENGLISH computer S-VIDEO VIDEO AUDIO L (MONO) RGB cable for PC to COMPUTER IN COMPUTER OUT RS-232C COMPUTER IN VIDEO IN AUDIO R AC IN O to COMPUTER OUT to AUDIO IN PC audio cable (option) to PC audio output AUDIO OUT Important: · Connectors or analog RGB output adapters may be necessary depending on the PC connected to this projector. Please contact your dealer. · The audio input for this projector is a stereo pin jack. (Speaker output is mono.) Please check the available cable for the audio input terminal of the PC. Some personal computer may not have the audio output terminal. · Select AUDIO MODE COMPUTER to hear and to sound for the COMPUTER. (Refer to page 16). · When connecting audio output of a personal computer which audio output is mono, connect to the audio input L terminal. For using Macintosh · A monitor output adapter is necessary for a Macintosh if it has no video port. Please contact your dealer. · A MAC adapter for RGB cable may be necessary depending on the personal computer connected to this projector. Please contact your dealer. ´ I MAIN to monitor port MONITOR OUTPUT RGB cable for PC (option) When outputting to both a PC monitor and the projector. EN ­ 11 Preparing the projector for operation Getting ready for projection 1. Connect the power cord provided to the projector. 2. Connect the power cord to the wall power outlet. 3. Remove the lens cap. Warning: · Do not look directly into the lens when projector is "ON". · The lens cap is for protecting the lens. If you leave the power on with the cap on, the cap may be warped. Please remove the lens cap when you turn the power on. · This projector is equipped with the power cords for both U.S. and Europe. Use the appropriate power cord for your country. · A three-pin grounding type power plug is used with the projector. Do not remove the grounding pin on the power plug. If you are unable to insert the plug into the outlet, contact your electrician to replace your A/C outlet. · The supplied power cord for U.S. is used for 120V only. Never connect to any outlet or power supply having a different voltage or frequency. If you connect to the power supply having a different voltage, please use the appropriate power cord. · Use 100-240V AC 50/60Hz correct voltage otherwise it may lead to fire or electric shock. · Do not place any objects on the power cord, and keep the projector away from heat sources to avoid breaking the power cord. A broken power cord can cause fire or electric shock. · Do not revise or alter the power cord otherwise it may cause fire or electric shock. Contact your dealer if the cord is broken. Caution: · Plug in firmly and unplug by holding the plug, not by pulling the cable out. · Do not plug in or out with wet hands. It may cause an electric shock. Adjusting the angle of projection For the best result, project onto a flat screen with a 90 degree angle to the floor. If necessary, tilt the projector by adjusting two foot adjustments on the bottom of the projector. screen Adjustment foot 1. Lift the projector to the appropriate angle. 2. Press the Front height adjuster button, this will allow the adjustment foot (up and down) to slide out to the position. 3. Release the Front height adjuster button to lock the feet in that position. Front height adjuster button Adjustment foot (up and down) After using the projector 4. Return the adjustment foot (up and down) into the projector by pressing the Front height adjuster button. When the left and right angles are different Adjust the angles with adjustment feet (right and left), which are on the bottom of the projector. Adjustment foot (right and left) Important: · The image becomes trapezoid shape when the screen or project is not level. Use KEYSTONE button and { or } buttons on the remote control to adjust, however, the circumference of the image may not be focused. · Screen on a flat wall with a 90° angle to the floor. · Align projector to produce a full screen display as illustrated on page 9. · The distance from the projector to the screen must be compatible with screen size chart on page 9. Note the distance from the screen chart. EN ­ 12 To operate projector power ON ENGLISH 2·9 MUTE button O COMPUTER OUT USB RS-232C COMPUTER IN VIDEO IN S-VIDEO VIDEO AUDIO L (MONO) AUDIO R AC IN 3·7·8 4 AUTO POSITION POWER COMPUTER LAMP VOLUME TEMP SOURCE VIDEO MENU AUTO POSITION button MUTE button MUTE ENTER 1. Turn on the equipment connected to the projector. 2. Put the projector into standby mode by pressing the main power switch. The POWER indicator lights up red. · The POWER indicator blinks red for 2, 3 seconds after the power switch ON. In this time, the buttons will not work. 3. Turn the projector on by pressing the POWER button. The light source lamp starts warming up, eventually turning completely on. In case the light source lamp does not come on, wait for one minute before switching power on again. · If the main power switch to the unit is turned off within two minutes of turning off the light source lamp, power will not be applied to the lamp for one minute when the next time the main unit power switch is turned on. When this happens, the indicator lamp will blink for one minute. Condition Indicator LAMP POWER Stand-by When light source lamp is on Light source lamp held off temporarily Green - Red Green Red Important: · A darkened image may be seen right after pressing the POWER button due to warming up of this projector. While warming up, no other commands can be accepted. ´ I MAIN 3·7·8 4 AUTO POSITION button POWER MUTE SOURCE KEYSTONE MOUSE LASER R-CLICK MENU ENTER AUTO POSITION STILL P in P EXPAND STILL button ­ VOLUME + · When the lamp indicator is blinking red, the the lamp should be replaced. Replace the lamp. See pages 23 and 26. · The picture might not be of optimum performance in extreme hot or cold conditions. (The projector is not malfunctioning.) 4. Select the desired external input source by using the SOURCE button on the remote control (or the COMPUTER or VIDEO button on the control panel). · The SOURCE, COMPUTER or VIDEO buttons do not work when MENU is displayed. · The projector automatically selects the appropriate signal format. The selected signal format is displayed on the screen. · When selecting the COMPUTER input, the image may flicker. Press the $ or % button to adjust the image. 5. Adjust the image size with the zoom ring by turning it. 6. Adjust the focus with the focus ring by turning it. focus ring tele zoom ring wide near far EN ­ 13 To operate projector power ON (Continue) Turning off the projector 7. Press the POWER button. The message "POWER OFF? YES : PRESS AGAIN" appears on the screen. · To exit from this mode, press any button except POWER, LASER, mouse pointer, R/L-click, STILL and VOLUME + and - buttons. 8. Press the POWER button again. The light source lamp will be turned off. Pressing the POWER button second time will shut off the light source lamp, but the exhaust fan continues to operate for 60 seconds to cool down the light source lamp and LCD panels. In this time, the lamp indicator will be turned off. 9. Turn off the main power switch. When turning off the main switch, the POWER indicator turns off. · In cases where the main power switch is accidentally turned off when either the intake/exhaust fan or the power source lamp is in operation, allow the unit to cool down for 10 minutes with the power turned off. Repeat step 3 when turning on the power source lamp. If the lamp does not turn on immediately, repeat this step two or three times. Replace the lamp if it should still fail to turn on. AUTO POSITION button When the source is selected to COMPUTER and the image is not in the right place, follow as shown below. 1. Set screen to the brightest display as possible (e.g., full-screen display of the "Trash" window). 2. If the screen saver is running, turn off the screen saver. 3. Press the AUTO POSITION button. · If the image is still not in the right place, adjust the image position by using the SIGNAL menu. The sound from the speaker The sound from the speaker is mono. · When inputting mono sound, connect to AUDIO L terminal. · The output sound is selected by changing the setting of AUDIO MODE in the FEATURE menu. See page 16 for details. The volume from the speaker Press the volume + or ­ button to change the volume from the speaker. The volume control bar will appear on the screen. 30 · The volume control bar will disappear about 4 seconds after releasing the volume buttons. · The volume buttons do not work when MENU selection bar or MENU is displayed. AV mute Image and audio are temporarily erased with pressing the MUTE button. To restore the image and audio to the normal mode, press the MUTE button again. · To prevent the damage of the LCD, the image and audio will be restored automatically to the normal mode, 10 minutes after setting the AV mute mode. Caution: · When you have finished using this equipment, wait 60 seconds for the exhaust fans to stop. Then turn off the main switch and unplug the power cable from the wall outlet, for safety purposes. · After the lamp is turned off, the lamp cannot be switched on again for 60 seconds as a precautionary measure. If you wish to turn on the projector again, wait until the indicator is off then press the POWER button. · The exhaust fan rotates faster when the temperature around the projector rises. · When the temperature around the projector becomes too high, the sign "TEMP!!" blinks red on the screen. If the temperature stays too high, the lamp will be shut off automatically . The projector automatically shuts off when the lamp is used up in about 2,000 hours and cannot be used until the lamp is replaced and the internal timer is reset. See page 23. EN ­ 14 Menu operation ENGLISH OFF OFF OFF 30 min IMAGE CONTRAST BRIGHTNESS COLOR MATRIX USER COLOR TEMP. ± 30 ± 30 sRGB STANDARD USER STANDARD HIGH LOW USER ± 10 ± 10 ± 10 RED YELLOW GREEN CYAN BLUE MAGENTA SATURATION CONTRAST R CONTRAST B BRIGHTNESS R BRIGHTNESS B ± 30 ± 30 ± 30 ± 30 ± 30 ± 30 ±5 ± 30 ± 30 ± 30 ± 30 SHARPNESS TINT COLOR INSTALLATION KEYSTONE AUTO POWER ON AUTO POWER OFF SPLASH SCREEN IMAGE REVERSE MENU POSITION EXPAND MODE FRAME POSITION AUDIO MODE VIDEO SIGNAL ANAMORPHIC LANGUAGE RESET ALL MEMORY CALL HORIZ.POSITION VERT.POSITION FINE SYNC. TRACKING COMPUTER INPUT HOLD (Displays only when the source is selected to VIDEO) (Displays only when the source is selected to VIDEO) -15°, -12°, -9°, -6°, -3°, 0°, +3°, +6°, +9°, +12°, +15° ON, OFF OFF, 5, 10, 15, 30, 60 min ON, OFF OFF, MIRROR, INVERT, MIRROR INVERT 1=Upper left, 2=Lower right 1-4 (AUTO : When the source is selected to COMPUTER) 1-5 COMPUTER, VIDEO, C/V AUTO, NTSC, PAL, SECAM, 4.43NTSC, PAL-M, PAL-N, PAL-60 ON, OFF , English, Español, Deutsch, Français, Italiano, OK AUTO, USER1, USER2 0 - 999 * 0 - 999 * 0 - 39 0 - 9999 * RGB, YCBCR / YPBPR AUTO ON OFF FEATURE SIGNAL * : Setting range is different according to the type of the signal. BEGIN END -1 - -99 1 - 99 0 - +63 * 1 - 63 * 0 - 9999 * 0 - 9999 * AUTO, 0 - 7 AUTO, ON, OFF 0 - 383 0 - 383 0 - 510 0 - 510 USER MEMORIZE DELETE DEFAULT USER1, USER2 USER1, USER2 CLAMP POSITION CLAMP WIDTH HORIZ. PIXELS VERT LINES PLL VERT. SYNC SHUTTER (U) SHUTTER (L) SHUTTER(LS) SHUTTER(RS) Basic operation Several settings can be adjusted using Menu. EXAMPLE: Auto power off time setting 1. Press the MENU button. Opt 4. Press the { or } button to select AUTO POWER OFF. AUTO POWER ON AUTO POWER OFF 5. Press the $ or % button to adjust auto power off time. AUTO POWER ON AUTO POWER OFF XGA60 IMAGE 2. Press the $ or % button to select the INSTALLATION menu. Opt 6. Exit the menu system by pressing the MENU button several times. · If the menu operation is not working, press the RESET button on the terminal board using a suitable sharp object, push gently. · The settings with 2 mark, you should press the ENTER button after selecting. XGA60 INSTALLATION 3. Press the ENTER button (or } button). Opt XGA60 0° OFF OFF ON OFF INSTALLATION KEYSTONE AUTO POWER ON AUTO POWER OFF ON SPLASH SCREEN IMAGE REVERSE EN ­ 15 Menu operation (continued) 1 IMAGE CONTRAST ........ Adjusts the picture contrast. The contrast becomes higher XGA60 as the number increases. IMAGE BRIGHTNESS .... Adjusts image brightness. The image becomes brighter as CONTRAST 0 the number increases. BRIGHTNESS 0 COLOR MATRIX. ...... Adjusts color balance in each color of the image. See page USER COLOR MATRIX 18. COLOR TEMP. STANDARD COLOR TEMP... . Adjusts color temperature. See page 18. SHARPNESS 0 SHARPNESS ...... Adjusts the picture sharpness. The sharpness becomes TINT 0 sharper as the number increases. COLOR 0 TINT .................... Adjusts the color balance of the image. The color balance of the image shifts green as the number increases and shifts to purple as the number decreases (displays only when the source is selected to VIDEO). · When the TV50 (PAL, SECAM) signal is inputted, you cannot adjust the TINT. COLOR ................ Adjusts the color intensity of the image (displays only when the source is selected to VIDEO). Opt 2 INSTALLATION KEYSTONE ........ Adjusts keystone correction of the image. If the image has XGA60 keystone distortion, select the approximate setting. For INSTALLATION normal use, select 0°. KEYSTONE 0° AUTO POWER ON ..... To select whether to boot up automatically when the power is AUTO POWER OFF ON turned on external to the projector. In this case, the main AUTO POWER OFF OFF power switch of the projector has to be ON. Set this when the SPLASH SCREEN ON projector is hanging on the ceiling. IMAGE REVERSE OFF · The projector is in stand-by mode when the lamp is not on. In this case, use the remote control to turn on the lamp. AUTO POWER OFF .. Use to select the length of time before projector switches to stand-by when there is no input signal selected source. SPLASH SCREEN . Use to display the splash screen on the screen when the power is turned ON. IMAGE REVERSE Use to reverse or invert the projected image. MIRROR is used to rear projection. MIRROR, INVERT is for rear projection ceiling mount. Opt ON 3 FEATURE MENU POSITION . Use to select the position where the menu is displayed, XGA60 (upper left) or (lower right). FEATURE EXPAND MODE Selects the mode of enlarging screen. See page 21. MENU POSITION 1. FRAME POSI. .... Sets the position of sub screen. See page 21. A EXPAND MODE 1. AUDIO MODE ....... Select COMPUTER to output the sound which is inputted FRAME POSI. 3. to audio input terminal only when the source is selected to AUDIO MODE VIDEO COMPUTER. Select VIDEO to output the sound which is ? VIDEO SIGNAL AUTO inputted to audio input terminal only when the source is ANAMORPHIC OFF selected to VIDEO. Select C/V (COMPUTER/VIDEO English LANGUAGE Ë mode) to output the sound which is inputted to audio input OK RESET ALL terminal at all time. VIDEO SIGNAL . When AUTO is set, the appropriate video format is automatically selected according to the input signal. If the image does not appear correctly, select the desired video format manually. ANAMORPHIC ... Set ON when displaying DVD discs which are recorded in letter boxed images. LANGUAGE ....... Use to select the language for the projector display such as menu. ( / English / Español / Deutsch / Français / Italiano / ) RESET ALL ........ Use to reset the MENU setting (except LANGUAGE). Opt A A A A EN ­ 16 4 SIGNAL MEMORY CALL ........ Use to select AUTO, USER 1 or USER 2. See below. HORIZ. POSITION .... Use to adjust the horizontal position of the image. VERT. POSITION ..... Use to adjust the vertical position of the image. FINE SYNC. ....... Use to synchronize the projector with PC input signals so that the image is not blurred. TRACKING ......... Use to avoid image noise such as wide stripes. COMPUTER INPUT .... The unit adjusts itself automatically when connected to a DVD player with a component video output (Y, CB, CR). In the case ( Y, PB, PR). In the case the projector is connected to equipment that includes RGB output terminal, adjust to RGB mode. HOLD .................. Adjusts the image when flagging occurs near the top of the screen. Opt XGA60 AUTO 0 0 0 0 RGB AUTO SIGNAL A U MEMORY CALL HORIZ. POSITION VERT. POSITION FINE SYNC. TRACKING RGB RGB COMPUTER INPUT HOLD USER MEMORIZE DELETE DEFAULT 5 SIGNAL - USER (Normally, there is no need for adjustments.) CLAMP POSITION/ CLAMP WIDTH .........If you use something similar, the brighter colors of the SIGNAL-USER projected image may become blurred. In this case, adjust CLAMP POSITION CLAMP POSITION or CLAMP WIDTH. CLAMP WIDTH HORIZ.PIXELS .. Use to adjust the width of the image. The image size grows HORIZ. PIXELS wider as the number increases. (Adjust to the horizontal VERT. LINES pixels of the input signal for normal setting.) PLL VERT.LINES ...... Use to adjust the height of the image. The image size grows VERT. SYNC. higher as the number increases. (Adjust to the vertical SHUTTER(U) lines of the input signal for normal setting.) SHUTTER(L) PLL ...................... Use to adjust the image when skewed on top. Select AUTO SHUTTER(LS) for normal setting. SHUTTER(RS) VERT.SYNC. ...... Use to adjust the image when its motion does not run smoothly. Select AUTO for normal setting. SHUTTER(U) ..... Use to adjust the image when the noise etc. appears on top part of image. SHUTTER(L) ...... Use to adjust the image when the noise etc. appears on bottom part of image. SHUTTER(LS) .... Use to adjust the image when the noise etc. appears on left side of image. SHUTTER(RS) ... Use to adjust the image when the noise etc. appears on right side of image. 0 0 0 0 AUTO AUTO 0 0 0 0 User memory for signal setting This projector can memorize the maximum of 2 signal menu settings. Memorizing the setting 1. Select MEMORIZE in the SIGNAL menu, and press the ENTER button. 2. Press the $ or % button to select the memory which you wish to record (USER 1 or USER 2). 3. Press the ENTER button. Initialite the setting which has been changed (Default) Select RESET in the SIGNAL menu, and press the ENTER button. · When initializing, selection buttons will not work for about 2 - 18 seconds. Select the user setting Select MEMORY CALL in SIGNAL menu, and press the $ or % button to select the memory (USER 1 or USER 2). Reset the recorded setting 1. Select DELETE in the SIGNAL menu, and press the ENTER button. 2. Press the $ or % button to select the memory which you wish to reset (USER 1 or USER 2). 3. Press the ENTER button. The recorded setting will be reset. EN ­ 17 ENGLISH Picture adjustment Adjusting the image You can adjust the picture by using the IMAGE menu. Opt 3. Press the $ or % button to select USER }. · When you select sRGB or STANDARD, you can not adjust the color balance of the color. 4. Press the { or } button to select the desired color. · If you wish to adjust the color intensity of the image, select SATURATION. 5. Press the $ or % button to adjust the color balance of the color. 6. Repeat steps 4 and 5 for more adjustments. 7. Exit the menu system by pressing the MENU button several times. · If you want to emphasize color matching, select sRGB position in step 3. · When you select sRGB, all the settings of the color balance are displayed 0. In this case, the color balance is different from that when you set all the settings to 0 manually. · If you want to emphasize brightness, select STANDARD position in step 3. (The initial setting is STANDARD.) XGA60 0 0 USER STANDARD 0 0 0 IMAGE CONTRAST BRIGHTNESS COLOR MATRIX COLOR TEMP. SHARPNESS TINT COLOR To control the level of white-to-black in the image : Adjust CONTRAST in IMAGE menu. Press the % button to increase the contrast and the $ button to reduce it. To control the light level of the image : Adjust BRIGHTNESS in IMAGE menu. Press the % button to lighten the image and the $ button to darken the image. To adjust the detail and clarity of the image : Adjust SHARPNESS in IMAGE menu. Press the % button to make the picture seem sharper and the $ button to make it softer. To determine the intensity of the color : Adjust COLOR in IMAGE menu. Press the % button to increase the amount of color in the image and the $ button to decrease it. To adjust the red-green color balance of the image : Adjust TINT in IMAGE menu. Press the % button to increase the amount of red in the image and the $ button to increase the amount of green in the image. Color temperature 1. Select COLOR TEMP in IMAGE menu. 2. Press the $ or % button to select USER 2. 3. Press the ENTER button. COLOR TEMP.-USER CONTRAST R CONTRAST B BRIGHTNESS R BRIGHTNESS B 0 0 0 0 4. Press the { or } button to select the desired item. 5. Press the $ or % button to adjust the item. 6. Repeat steps 4 and 5 for more adjustments. 7. Exit the menu system by pressing the MENU button several times. About color temperature There are different kinds of white color. Color temperature is a way to show the differences. The white, which temperature is low, becomes raddish white. When the color temperature is higher, the white becomes more bluish. This projector sets this color temperature by changing the numbers of contrast blue and red. To set the color temperature high: Set the contrast B (Blue) number high, and the contrast R (Red) number low. To set the color temperature low: Set the contrast B (Blue) number low, and the contrast R (Red) number high. Color matrix This feature adjusts the color balance in each color of RGB (Red, Green, Blue), and their neutral colors (yellow, cyan, magenta) by using Color correction adjustment. Use Color correct adjustment when enphasizing a specific color, or when only a certain color balance is not correctly adjusted. 1. Select COLOR MATRIX in IMAGE menu. 2. Press the ENTER button. COLOR MATRIX sRGB RED YELLOW GREEN CYAN BLUE MAGENTA SATURATION STANDARD USER 0 0 0 0 0 0 0 EN ­ 18 Adjustment from personal computer Although this projector sets proper signal systems automatically for the image signal from personal computers, it cannot be applied to some of personal computers. In this case, press the AUTO POSITION button. If the images are still not projected correctly, use the MENU display to adjust the projected images. Opt Top part of image curves : Change the setting of HOLD in SIGNAL menu or PLL in SIGNAL - USER menu. HOLD ... Select ON, and adjust BEGIN or END for image which top part is the least curved. PLL ....... Select 0 - 7 for an image in which top part is the least curved. Select AUTO for normal setting. Image does not move naturally : Adjust VERT. SYNC. of the menu in SIGNAL USER menu. Select AUTO for normal setting. curved. Select AUTO for normal setting. · Do not change each menu setting in USER menu for normal setting. XGA60 AUTO 0 0 0 0 RGB AUTO SIGNAL A U MEMORY CALL HORIZ. POSITION VERT. POSITION FINE SYNC. TRACKING RGB RGB COMPUTER INPUT HOLD Simple adjustment method 1. Select HORIZ. POSITION in SIGNAL menu. 2. Press the$ or % button to adjust the horizontal start position (the left side of image). 3. Select TRACKING in SIGNAL menu. 4. Press the$ or % button to adjust the horizontal end position (the right side of image). 5. Repeat steps 1 to 4 for fine adjustment. 6. Select VERT. POSITION in SIGNAL menu. 7. Press the$ or % button to adjust the vertical start position (the top end of image). USER MEMORIZE DELETE DEFAULT Image moved to right or left : Adjust HORIZ. POSITION in SIGNAL menu. Press the % button to move the image to left. Press the $ button to move the image to right. Image moved to up or down : Adjust VERT. POSITION in SIGNAL menu. Press the % button to move the image to upward. Press the $ button to move the image to down. Image flickers / Image is out of focus : Adjust FINE SYNC. in SIGNAL menu. SIGNAL-USER CLAMP POSITION CLAMP WIDTH HORIZ. PIXELS VERT. LINES PLL VERT. SYNC. SHUTTER(U) SHUTTER(L) SHUTTER(LS) SHUTTER(RS) 0 0 0 0 AUTO AUTO 0 0 0 0 Wide stripes appear : Adjust CLAMP POSITION or CLAMP WIDTH of each menu in SIGNAL - USER menu. Noise appears on right or left side of image : Adjust SHUTTER (LS), SHUTTER (RS) or HORIZ. PIXELS of the menu in SIGNAL - USER menu. Noise etc. appears on top or bottom part of image : Adjust SHUTTER (U), SHUTTER (L) or VERT. LINES of the menu in SIGNAL - USER menu. EN ­ 19 ENGLISH Picture adjustment (continued) Specification of RGB signals in each computer mode of the projector Signal mode TV60 TV50 1080i 720p PC98 CGA70 CGA85 VGA60 VGA72 VGA75 VGA85 SVGA56 SVGA60 SVGA72 SVGA75 SVGA85 XGA43i XGA60 XGA70 XGA75 XGA85 SXGA70a SXGA75a SXGA85a SXGA60b SXGA75b SXGA43i SXGA60 SXGA75 SXGA85 MAC13 MAC16 MAC19 MAC21 HP75 HP72 SUN66a SUN76a SUN66 SUN76 SGI72 SGI76 IBM60 resolution (H x V) ­ ­ ­ ­ 640 x 400 640 x 400 640 x 400 640 x 480 640 x 480 640 x 480 640 x 480 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1152 x 864 1152 x 864 1152 x 864 1280 x 960 1280 x 960 1280 x 1024 1280 x 1024 1280 x 1024 1280 x 1024 640 x 480 832 x 624 1024 x 768 1152 x 870 1024 x 768 1280 x 1024 1152 x 900 1152 x 900 1280 x 1024 1280 x 1024 1280 x 1024 1280 x 1024 1280 x 1024 horizontal frequency (kHz) 15.73 15.63 33.75 45.00 24.82 31.47 37.86 31.47 37.86 37.50 43.27 35.16 37.88 48.08 46.88 53.67 35.52 48.36 56.48 60.02 68.68 63.85 67.50 77.49 60.00 75.00 46.43 63.98 79.98 91.15 35.00 49.72 60.24 68.59 62.94 78.13 61.85 71.81 71.68 81.13 76.92 82.00 63.42 Vertical frequency (Hz) 59.94 50.00 60.00 60.00 56.42 70.09 85.08 59.94 72.81 75.00 85.01 56.25 60.32 72.19 75.00 85.06 86.96 60.00 70.07 75.03 85.00 70.01 75.00 85.06 60.00 75.00 86.87 60.02 75.03 85.02 66.67 74.55 75.02 74.96 74.92 72.00 66.00 76.63 66.68 76.11 72.30 76.00 60.00 Normal mode (H x V) 1024 x 768 1024 x 768 1024 x 576 1024 x 576 1024 x 640 1024 x 640 1024 x 640 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 Real mode (H x V) ­ ­ ­ ­ 640 x 400 640 x 400 640 x 400 640 x 480 640 x 480 640 x 480 640 x 480 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 640 x 480 832 x 624 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 · When the EXPAND MODE of FEATURE menu is set to real screen display, by pressing the EXPAND button on the remote control, it will switch to the screen displaying the picture as its original size (real screen display). In the real screen display, pictures will be black-framed when picture resolution is lower than 1,024 x 768. Important: · Some computers may not be compatible with the projector. · The projector's maximum resolution is 1,024 x 768 pixels. It may not display correctly for the pictures of higher resolutions than 1,024 x 768. · The picture with a SYNC on G (Green) signal may jitter. · The picture with a SYNC on G (Green) signal may be tinged with green. · If the resolution and frequency of your computer are not shown on the table, change the resolution of your computer. You may find the compatible resolution and frequency. · Set the COMPUTER INPUT in SIGNAL menu to RGB, when inputting the HDTV signal as RGB signal. · Set the SIGNAL menu and USER menu as shown below, when 525p signal is inputted. Set TRACKING first. HORIZ. POSITION ............................. 143 VERT. POSITION ................................ 54 TRACKING ............................. 800 COMPUTER INPUT ............... YCBCR/YPBPR CLAMP POSITION ............................. +9 CLAMP WIDTH .................................. +3 HORIZ.PIXELS ....................... 616 VERT.LINES ........................... 444 VERT.SYNC. ........................... ON HOLD ...................................... ON2 BEGIN -1 END 8 EN ­ 20