User manual MITSUBISHI M430I

This guide describes the operation of the GSM telephone M430i. Edition 1, 2004. © MITSUBISHI ELECTRIC EUROPE B.V. - French Branch, hereinafter referred to as « Mitsubishi Electric » Whilst every effort has been made to ensure the accuracy of the instructions contained in this guide, Mitsubishi Electric reserves the right to make improvements and changes to the product described in this guide and/or to the guide itself, without prior notice. Mitsubishi Electric is a Mitsubishi Group Company. TABLE OF CONTENTS Page 4 Introduction SAR _______________________________________ 4 Declaration of conformity _______________________ 5 FCC warning statements _______________________ 5 General safety _______________________________ 5 Vehicle safety _______________________________ 5 Emergency calls _____________________________ 6 Care and maintenance ________________________ 6 AC/DC adaptor charger ________________________ 6 Battery use _________________________________ 6 PC cable ___________________________________ 7 Your responsibility ____________________________ 7 Security Code: PIN codes ______________________ 7 Disposing of waste packaging ___________________ 7 Using this guide Getting started Preparing the phone for operation _______________ 11 Basic operations ____________________________ 11 Tools Diary _____________________________________ 14 Calculator _________________________________ 17 Currency converter __________________________ 18 Alarm clocks _______________________________ 18 Infrared port ________________________________ 19 Using your mobile as a modem _________________ 19 Messages/Text editing Contents of the Messages menu ________________ 20 Accessing the SMS menu _____________________ 20 Reading a received SMS message ______________ 20 Reading stored SMS messages ________________ 21 Moving messages to SIM _____________________ 21 Forwarding messages ________________________ 21 Activating or deactivating the message alert tone ___ 21 Preparing the phone to send SMS messages ______ 22 Entering text / Edition mode ___________________ 22 Creating text models _________________________ 26 Editing a text model __________________________ 26 Sending a new SMS message _________________ 26 Signature __________________________________ 27 Outbox and SIM archive emitted messages _______ 27 Draft messages _____________________________ 28 Status request ______________________________ 28 Storage consumption _________________________ 28 Broadcast - cell broadcast (CB) messages ________ 29 Calls & times Call logs ___________________________________ 30 Call timers _________________________________ 30 Call costs - management ______________________ 31 Recorded call _______________________________ 32 Line selection _______________________________ 32 Phone book Storing names and telephone numbers ___________ 33 Adding a video to your Phone book card __________ 35 Adding a picture or an icon to your Phone book card 35 Setting a melody, a video or a speech note as a ringtone 35 Editing a Phone book or a SIM name card ________ 36 Viewing and calling Phone book numbers _________ 36 Voice dialling _______________________________ 37 Free space in the Phone book __________________ 37 Page 8 Page 11 Page 14 Page 20 Page 30 Page 33 2- Table of Contents Page 40 Page 48 Page 57 Page 69 Page 72 Page 72 Page 73 Page 84 Page 96 Page 101 Page 104 Creating a group of cards ______________________ 37 My card ____________________________________ 38 My number(s) display _________________________ 38 Fixed dialling numbers ________________________ 39 Export _____________________________________ 39 Camera The Camera screen and the related icons _________ 40 Closed clamshell: scenery shots ________________ 41 Open clamshell: self-portraits ___________________ 44 Video Video display _______________________________ 48 Closed clamshell: scenery shots ________________ 49 Open clamshell: self-filming ____________________ 53 Fun & media box Pictures ___________________________________ 57 Melodies ___________________________________ 60 Video _____________________________________ 61 Games & applications ________________________ 63 Speech notes _______________________________ 64 Frames ____________________________________ 65 Others _____________________________________ 67 Storage used _______________________________ 68 miniSDTM Card Handling and storage precautions _______________ 69 Protecting your data __________________________ 69 How to insert/extract your miniSDTM Card _________ 70 How to access the miniSDTM Card contents _______ 70 How to configure your miniSDTM Card ____________ 71 Storage used _______________________________ 71 Calendar Network services i-mode User interface _______________________________ 73 i-mode menu _______________________________ 73 i-mode applications __________________________ 74 Setting your i-mode features ___________________ 76 Mail system ________________________________ 77 Options ____________________________________ 82 Quick access to i-mode basic features ____________ 83 Settings Tones _____________________________________ 84 Display ____________________________________ 85 Keypad ____________________________________ 87 Phone settings ______________________________ 87 Voice mail __________________________________ 89 GSM services _______________________________ 90 Security features ____________________________ 94 miniSDTM Card _______________________________ 95 Appendix Glossary ___________________________________ 96 Troubleshooting _____________________________ 97 Error messages _____________________________ 98 Guarantee ________________________________ 100 Index Notes 3- Table of Contents INTRODUCTION T hank you for purchasing the M430i (GSM, DCS, PCS) mobile telephone. The mobile telephone described in this guide is approved for use on all GSM 900, DCS 1800 and PCS 1900 networks. Some of the messages displayed on your mobile may be different according to your subscription type and/or service provider. As with all types of radio transceivers, this mobile telephone emits electromagnetic waves and complies with international regulations when it is used under normal conditions and in accordance with the safety and warning messages given below. SAR THIS M430i PHONE MEETS THE EU REQUIREMENTS FOR EXPOSURE TO RADIO WAVES. Before a mobile phone is available for sale to the public, compliance with the European R&TTE directive(1999/5/EC) must be shown. This directive includes as one essential requirement the protection of the health and the safety of the user and any other person. Your mobile phone is a radio transmitter and receiver. It is designed and manufactured not to exceed the limits for exposure to radiofrequency (RF) energy recommended by The Council of the European Union1. These limits are part of comprehensive guidelines and establish permitted levels of RF energy for the general public. The guidelines were developed by independent scientific organisations through periodic, thorough evaluation of scientific studies. The limits include a substantial safety margin designed to assure the safety of all persons, regardless of age and health. The exposure standard for mobile phones (CENELEC standard EN 50360: 2001) employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit2 recommended by The Council of the European Union is 2.0 W/kg. Tests for SAR have been conducted using standard operating positions (with reference to CENELEC standard EN 50361: 2001) with the phone transmitting at its highest certified power level in all tested frequency bands3. Although the SAR is determined at the highest certified power level, the actual SAR level of the phone while operating can be well below the maximum value. This is because the phone is designed to operate at multiple power levels so as to use only the power required to reach the network. In general, the closer you are to a base station antenna, the lower the power output. The highest SAR value for this M430i model when tested for compliance against the standard was 0,754 W/kg. While there may be differences between the SAR levels of various phones and at various positions, they all meet the EU requirements for RF exposure. Additional information from the World Health Organization (WHO) Individuals: Present scientific information does not indicate the need for any special precautions for use of mobile phones. If individuals are concerned, they might choose to limit their own or their children's' RF exposure by limiting the length of calls, or using "hands-free" devices to keep mobile phones away from the head and body. RF absorbing devices: Scientific evidence does not indicate any need for RF-absorbing covers or other "absorbing devices" on mobile phones. They cannot be justified on health grounds and the effectiveness of many such devices in reducing RF exposure is unproven. Source: WHO Fact Sheet 193, June 2000. WHO: www.who.int/peh-emf. There are a number of independent sources of information available to users including: Royal Society of Canada: www.rsc.ca The International Commission on Non-Ionizing Radiation Protection (ICNIRP): www.icnirp.de The US Food and Drug Administration: www.fda.gov/cellphones/ The World Health Organization: www.who.int/emf Mitsubishi Electric belongs to the MMF, an international association of radio equipment manufacturers. The MMF produces this type of information in order to develop and present industry positions to independent research organisations, government and other research bodies. Mobile Manufacturers Forum 1. European recommendation 1999/519/EC 2. The SAR limit for mobile phones used by the public is 2.0 watts/kilogram (W/kg) averaged over ten grams of tissue. The limit incorporates a substantial margin of safety to give additional protection for the public and to account for any variations in measurements. 3. The maximum level of GSM emitted power is 250mW at 900 MHz and 125 mW at 1800 MHz according to the GSM standard. 4- Introduction Diamant Building, 80 Blvd. A. Reyers B-1030 Brussels Belgium www.mmfai.org Declaration of conformity Mitsubishi Electric hereby declares that this M430i (VGH08B) is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. A copy of the full Declaration of Conformity may be found on our website: http://www.mitsubishi-telecom.com FCC warning statements This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:--Reorient or relocate the receiving antenna.--Increase the separation between the equipment and receiver.-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. --Consult the dealer or an experienced radio/TV technician for help. General safety Use of the hands-free kit over extended periods of time and at high volume may seriously damage your hearing. Due to the possibility of radio frequency interference, it is important to follow special regulations regarding the use of radio equipment. Please follow the safety advice given below. Switch off your phone and remove the battery when in an aircraft. The use of mobile telephones in an aircraft may endanger the operation of the aircraft, disrupt the mobile phone network and is illegal. Switch off your phone when at any refuelling point or near inflammable material. Switch off your phone in hospitals and any other place where medical equipment may be in use. Respect restrictions on the use of radio equipment in fuel depots, chemical plants or where blasting operations are in progress. There may be a hazard associated with the operation of phones close to inadequately protected personal medical devices such as hearing aids and pacemakers. Consult your doctor or the manufacturers of the medical device in question to determine whether it is adequately protected. Operation of your phone close to other electronic equipment may also cause interference if the equipment is inadequately protected. Observe any warning signs and manufacturers recommendations. Vehicle safety Respect national regulations on the use of mobile telephones in vehicles. Road safety always comes first! Always give your full attention to driving. - Do not use a hand-held phone while driving. If you do not have a 'hands free' car kit, stop and park your vehicle safely before using your phone. Please ensure that you are fully aware of the laws in your country regarding the use of hand-held mobile devices whilst driving. - If incorrectly installed in a vehicle, mobile telephones can interfere with the correct operation of the 5- Introduction vehicle electronics, such as ABS anti-lock brakes or air bags. To avoid such problems ensure that only qualified personnel carry out the installation. - Do not place the phone on the passenger seat or where it could fall during sudden braking or a collision. Always use the holder. Emergency calls You can make emergency calls by dialling the European standard emergency number 112 or the USA emergency number 911 even if there is no SIM card in your phone. Emergency calls can even be made if the phone is PIN or electronically locked or call barred. In some countries local emergency numbers can still be used for emergency purposes but the phone may have to contain a valid SIM card. When making an emergency call remember to give all the necessary information as accurately as possible. As the phone may be the only means of communication at the scene of an emergency, do not cut off the call until told to do so. Mobile phones rely on wireless and landline networks which cannot be guaranteed in all conditions. You should therefore never rely solely on wireless phones for essential emergency communications. Care and maintenance This mobile telephone is the product of advanced engineering, design and craftsmanship and should be treated with care. The suggestions below will help you to enjoy this product for many years. - Do not expose your phone to any extreme environment with high humidity or temperature. - Do not expose your mobile to or store your mobile in cold temperatures. When the phone warms up to its normal temperature after switch on, moisture may form inside and damage the electrical parts. - Do not attempt to disassemble the phone. There are no user serviceable parts inside. - Do not expose your phone to water, rain or spilt beverages. It is not waterproof. - Do not drop, knock or violently shake your phone. Rough handling may damage it. - Do not clean your phone with strong chemicals or solvents. Wipe it only with a soft, slightly dampened cloth. - Do not place the telephone alongside computer discs, credit or travel cards or other magnetic media. The information contained on discs or cards may be affected by the phone. - Do not connect incompatible products. The use of third party equipment or accessories, not made or authorised by Mitsubishi Electric, invalidates the warranty of your phone and may be a safety risk. - Do not remove the labels. The numbers on it are important for aftersales service and other related purposes. - Contact an authorised service centre in case of problem. AC/DC adaptor charger This mobile phone was designed to be used only with the supplied AC/DC charger. Use of any other charger or adaptor invalidates any approval given to this apparatus and may be dangerous. Battery use Batteries may be charged hundreds of times but gradually wear out. When the operating time (standby and talk time) is noticeably shorter than normal, it is time to buy a new battery. If the battery is totally empty the battery level symbol may not be displayed at once when connecting the battery charger. Moreover the mobile cannot be turned on. Up to 15 minutes may be necessary to reach the required 4% battery charge to turn your mobile on and allow the battery charge symbol to be displayed. Battery charging may only operate between 0°C and + 45°C. - Do not leave batteries connected to a charger longer than necessary. Overcharging shortens battery life. - Disconnect battery chargers from the power source when not in use. - Do not expose batteries to high temperatures or humidity. - Do not dispose of the batteries in fire. They may explode. - Avoid putting the batteries into contact with metal objects which can short circuit the battery terminals (e.g. keys, paper clips, coins, etc.). - Do not drop or subject the batteries to strong physical shocks. - Do not try to disassemble any of the battery packs. - Use only specified Mitsubishi charger (see above). - If the battery terminals become soiled, clean them with a soft cloth. - Batteries may warm up during charging. Caution: Risk of explosion if the battery is replaced by any other battery than the Mitsubishi MA-0803. 6- Introduction Battery disposal In compliance with European environmental protection directives, used batteries must be returned to the place of sale, where they are collected free of charge. Do not dispose of your batteries within household waste. PC cable The PC cable allows you to connect the GSM mobile telephone to a Personal Computer in order to exchange data. The PC cable may not be supplied with your mobile. Please check this accessory availability with your retailer. Your responsibility This GSM mobile telephone is your responsibility. Please handle it with care and in respect of local regulations. Please keep it in a safe place at all times and out of reach of children. Familiarise yourself with and use the security features to block unauthorised use. If your phone and/ or SIM card are lost or stolen, call your service provider immediately to prevent illegal use. When not in use, turn off the phone and remove the battery. Security Code: PIN codes The phone and SIM card are delivered to you pre-programmed with codes that protect the phone and SIM card against unauthorised use. A short description of each follows. See "Security features", page 94 to change your PIN and phone lock codes. PIN and PIN2 codes (4-8 digits) All SIM cards have a PIN (Personal Identity Number) that protects the card against unauthorised use. Entering the wrong PIN code three times disables the SIM card and the message SIM Blocked is then displayed. Enter PUK appears. PUK and PUK2 codes (8 digits) Please ask your service provider for your PUK code. Use it to unblock a disabled SIM card (see "Security features", page 94). The PUK2 code is required to unblock the PIN2 code (see above). Call barring password (4 digits) This password is used to bar various types of calls, made or received, from the phone (see "Call barring password", page 94). Phone lock code (4 digits) This code is set to 0000 on delivery. You can change it. Once changed it cannot be identified by the manufacturer over the phone. Please refer to "Phone lock code", page 94 for more details. i-mode lock (4 digits) The default i-mode lock code is 0000. It allows you to forbid any unauthorised use of the i-mode feature (see "i-mode lock", page 74). We advise you remember these codes and make yourself familiar with their purpose and operation. Disposing of waste packaging The packaging used for this phone is made of recyclable materials and as such should be disposed of in accordance with your country's national legislation on the protection of the environment. Please take care to separate the cardboard and plastic elements and to dispose of them in the correct manner. 7- Introduction USING THIS GUIDE P lease read this user guide carefully. It contains information about your phone and the way that it operates on the network. Some of the features described in this user guide are network dependent. Do not forget to check with your service provider which of these you can use. You may need to take out additional subscriptions to activate certain features. Main screen / External screen Your M430i is a clamshell-type mobile. It has two colour displays: an internal screen (Main screen) and an external screen. Both display information about the state of the mobile and connection with the network and both are designed to help you enjoy a clear information. All features described in this guide are to be reached via the Main screen, unless otherwise specified (e.g.: features related to the Camera and Video applications). Key actions To help you quickly familiarise yourself with your mobile, these are the keypad and side keys symbols used throughout the guide. [OK] key in the middle of the cursor key (to validate OK on the display and to get direct access to the Camera (short press) and Video (long press) applications). Left softkey (to validate the item above (usually an action), give direct access to the Messages menu (long press) and to the Mail menu (short press) from the standby display). Right softkey (to validate the action above: usually Exit - and and give direct access to the menu displayed above, to the i-mode browser (short press) and to the JavaTM applications (long press) from the standby display). [Menu/T9] key (to access the nine icons Main menu, to switch from the T9 mode to the Multitap mode (and vice-versa) while in edition mode, to access the Options menu of the applications and the i-mode Options menu). [Phone book] key gives direct access to the Phone book list from the standby display or the «To» field edition mode, while a call is in progress or to swap from the Phone book names list to the SIM names list. [Clear] key (to delete a character in edition mode; to activate the game/application set as a standby display on your Main screen). [Right] arrow on cursor key [Left] arrow on cursor key [Up] arrow on cursor key [Down] arrow on cursor key [Send/Call] key [End, On/Off] key [Up] side key [Down] side key [Menu] side key [Camera/Video] side key Icons menu The availability of the Calendar or Network services menu depends on your SIM card. 8- Using this guide User guide notes Here is how to follow the instructions contained in this user guide and use your mobile. These are examples. The bold text stands for information displayed while using your mobile. USER GUIDE INFORMATION TYPES ACTIONS TO PERFORM Press OK Press the [Menu/T9] key. Select Settings. Select Read (item above Left softkey) Select Exit (item above right softkey) Select Camera & Video Press the key to validate OK (middle of the display). From the standby display press the key to access the main menu, scroll Up , Down, Left or Right to the Settings menu item and press OK to access the sub-menu. Press the key underneath Read. From the standby display press the key underneath Exit once to return to the previous screen. Press and hold to return to the standby screen (except whilst in the i-mode menu). Use the cursor key to scroll up, down, left or right to the required menu item and validate by pressing OK. E.g. 'Select Camera & Video': scroll to the Camera & Video menu item with the navigation keys (Up , Down , Left , Right ) and press the [OK] key to validate your selection. The indicates that more options or sub-menus are available when pressing OK. The ... at the beginning or at the end of an Options menu indicates that more options or sub-menus are available by scrolling up or down. Insert ... Using the dynamic scroll panels When scrolling the menu, the following scroll panel type gives you a clear view of the information to be entered. 1 2 3 The list of elements to be entered is displayed. Scroll down to the field(s) you want to fill in and press OK. Enter the requested information or select the requested item and select OK to validate. Fill in as many fields as necessary and select Save to store all the information entered. The arrow keys displayed at the bottom of the screen show the scrolling possibilities. Understanding the graphic display indicators (icons) Icons may be displayed at the top of the mobile screen. The icons indicate the phone's state and operational conditions when in use. The following icons may be displayed: SIM memory in use Phone memory in use: refers to information from the Phone book cards. GPRS service icon. This indicates that data packet services or connection to the i-mode GPRS connection icon. This is displayed when a GPRS connection is in progress. Home zone. This is displayed when the phone is connected to its home network. Roaming. This is displayed when the phone is connected to a network other than its Call diverting. This indicates that all incoming calls are being diverted. Call diverting is Alarm clock. Vibrator alert. network dependent. home network. are available. 9- Using this guide Keypad lock. Line 2. This indicates that the second line is in use (subscription dependent). Silent mode On. Mute. Auto-switch-off/on mode is activated. Infrared port. This indicates that the infrared port is active. i.e. that data can be received Short message service (SMS). This is displayed when one or more short messages Voice Mail. This is displayed when a Voice Mail message has been received and stored have been received and not yet read. flashes when the SMS message box is full and no new messages can be stored. SMS availability is network dependent. via the infrared port. by the networks Voice Mail centre. Voice Mail availability is network dependent. Withheld number. This is displayed when the caller does not wish his identity to be shown. Unanswered call. This is displayed when an incoming call has not been answered. Battery level indicator. This is permanently displayed to show the current battery charge level. Five levels are shown: from full (5 bars) to low (one bar). If the icon is empty, the mobile needs recharging. Signal strength level. There are five strength levels. These show the strength of the received signal. The more bars, the stronger the signal. If the network cannot be found, no strength level is displayed. Tegic edition mode. Multitap edition mode. Arrow keys. These icons are displayed during menu operation to indicate that more or . items in the menu can be accessed by pressing Secured connection. This icon is displayed when a secured connection is in progress. Games & Applications software in use. Games & Applications icon. It is displayed when a game or an application is running. Problem in launching an application in Auto Start mode. Application set as wallpaper icon. This icon is displayed when an application is set as wallpaper. Mail or MMS on mobile Mail or MMS box on mobile full Mail on server MMS on server Mailbox on server full MMS box on server full Status light At the bottom of your clamshell (please refer to Getting started with your M430i) several light colours indicate your mobile's state (charging, event on mobile, etc.). The lights can be green, orange, red, yellow or blue. You can activate/deactivate these lights: MODE MOBILE ON MOBILE OFF Power saver Incoming call Missed event (SMS, unanswered call, etc.) Battery charging Network available The green light flashes No network The orange light flashes The blue light flashes Flashes alternately green Flashes alternately and yellow orange and yellow The green light flashes The orange light flashes Battery charging over The green light flashes The orange light iflashes The red light is On While charging, the battery charge symbol is displayed if your mobile phone is ON. Once charging is over, the screen backlight is turned Off (black screen). 10- Using this guide GETTING STARTED Preparing the phone for operation Please refer to the Getting started with your M430i booklet. Basic operations Turning the phone On 1 2 Open the clamshell. Press and hold the [On/Off] key. A beep sounds at mobile activation. When switching the mobile On for the first time or if the phone has been incorrectly switched off may be displayed. If your SIM card is PIN protected, Enter PIN is displayed. Enter the PIN code and select OK. If prompted, enter the date & time or select Exit if the information is correct. Please refer to "Security Code: PIN codes", page 7 and to "Security features", page 94 for more details on your PIN and lock codes. 3 4 If an image is set as a Welcome screen and/or a melody has been set as a Welcome melody, the mobile first requests the PIN code then shows the selected image/animation and plays the selected melody before showing the standby display (please see "Setting a still or animated image as a standby display (for the Main screen or the External screen), as a Welcome screen or as a Goodbye screen from the Pictures folder", page 59 and "Melodies", page 60). If you set an application as a standby display for your mobile internal screen (see "Games & applications", page 63), an information screen is displayed and proposes to display the Doja application. Making a call The phone can make and receive calls only when it is switched on, when a valid SIM card is inserted and when it is connected to a GSM, DCS or PCS network service. If the keypad is locked you can receive calls but you cannot make any (see "Keypad lock", page 13) except emergency calls. To make a call: 1 2 3 Open the clamshell. Dial the phone number or select one from your Phone book (press the [Left] arrow key or the [Phone book] key from the standby display and select one of the available names). Press the [Call/Send] key. Whilst in conversation an Options list (Speaker On or Speaker Off, AutoDTMF, Hold, Retrieve, Mute or Unmute, End call and Record) and Sp.on (Speaker On)/Sp.off (Speaker Off, after the speaker has been set to On) is available from the Left and Right softkeys. You can set the conversation volume by scrolling Up and Down In compliance with European regulations, you are obliged to inform your correspondent before recording a phone conversation. Answering a call When receiving a phone call: 1 Press the [Call/Send] key. You can also answer a call by opening the clamshell. Please see "Active flip", page 88. When a phone call is received the caller name, number (see "Receiving caller ID", page 92), picture/video (see "Storing names and telephone numbers", page 33) may be displayed if you created a Phone book card corresponding to this caller. 11- Getting started Rejecting a call When receiving a phone call: 1 Press the [On/Off] key or close the clamshell to reject the call (the call is then forwarded to your mailbox). Press and hold the [Camera/Video] side key if the clamshell is closed. or: 1 1 Ending a call Press the [On/Off] key. You can also end a call by closing the clamshell. Please see "Active flip", page 88. To stop the ringtone When receiving a phone call you have the possibility to stop the ringtone. 1 Press No ring if the clamshell is open or press the [Menu] closed. side key if the clamshell is Holding your mobile (while making or receiving a call) How to hold the phone. Avoid covering the upper back of the phone to allow maximum emission and reception quality. When using the hands free mode, do not put the phone to your ear. The standby display (Main screen) When switched On, the mobile searches for connection with the network. Once the connection has been established, a beep sounds and the network and/or service provider name or logo are displayed together with the time and date, the signal strength and the battery charge level. If the mobile cannot find a valid network, the signal strength and the operator name are not displayed. On the main screen, the four arrows indicate that features can be accessed via the four arrows on the cursor key. The oval symbol in the middle of the cursor key indicates that the Camera application (short press) and the Video application (long press) can be accessed by pressing the OK key (in the middle of the cursor key). Mail and i-mode indicate that you can directly access the mailer and the i-mode service by pressing the softkeys. The standby display (External screen) The provider name as well as the time, the signal strength and the battery charge levels are also displayed on the external screen when the mobile is activated. On both screens, indicates that your mobile is connected to a GPRS network. 12- Getting started Keypad lock When activated, the keypad lock feature prevents accidental actions occurring (e.g. camera activation) whilst the phone is being carried in a pocket or a bag for instance. Incoming calls can however be received and answered. Once the call is over, the keypad lock is automatically reactivated. To activate the keypad lock from the standby display: 1 2 1 2 3 1 2 1 2 Open the clamshell. Press and hold . Keypad locked is displayed. Open the clamshell. Press the [Menu/T9] key. Select Settings. Select Keypad, then select Keypad lock. Open the clamshell. Select Unlock and press To activate the keypad lock from the main menu: To deactivate the keypad lock: or press and hold . Keypad unlocked is displayed. Turning the phone Off Open the clamshell. Press and hold the [On/Off] key. A tone sounds to confirm your action and a Goodbye screen is displayed whilst the mobile switches off. You can set a melody and/or a picture to be played/displayed when the mobile is switched off (please see "Setting a still or animated image as a standby display (for the Main screen or the External screen), as a Welcome screen or as a Goodbye screen from the Pictures folder", page 59 and "Melodies", page 60). Do not take the battery out of the mobile without first turning the phone off. Data might be lost. Should this happen a first-aid kit symbol is displayed the next time the mobile is activated. Power saver When the phone has not been used for more than one minute, the internal and external screens turn Off (black screens). Press any key or open the clamshell to turn the internal and external screens On. However, this does not prevent any operation on your mobile from taking place. You can therefore receive a call, an SMS, etc. whilst the internal and external screens are turned Off. 13- Getting started TOOLS scrolling to the main icons menu, access to WhenInfrared portthe Toolsismenu fromby selecting Infrared ondirectleft side of the section possible the the display. The Tools menu allows access to a diary, a calculator, a currency converter, several alarm clocks and the infrared port opening. Diary The Diary is divided into three parts: -The Calendar (to manage events), -The Tasks list (to manage tasks), -The Storage used (to provide the diary memory information). An event is a diary entry that has a direct implication on your timetable (e.g. a meeting). A task is a diary entry that has no direct implication on your timetable (e.g. organising a journey). Calendar The calendar allows you to store up to 100 events scheduled to occur either once, daily, weekly, monthly or yearly. Each entry can contain up to 50 characters plus a reminder alarm. Events may be viewed on a daily, a weekly or a monthly basis, and may be sent via the Infrared port or by SMS. To enter an event 1 2 3 4 5 Press the [Menu/T9] key. Select Tools. Select Diary. Select Calendar. A Monthly or Daily view is displayed (the Daily view is displayed if an event is related to the current day). Select Options. Select New event. An empty new event card is displayed with the following fields: Title (up to 10 characters), Description (up to 50 characters), Start date & time, End date & time, Alarm, Location, Repetition. 6 7 Enter or select the requested data. Confirm each entry by pressing OK. Select Save to confirm data storage. 1 2 3 4 5 Press the [Menu/T9] key. Select Tools. Select Diary. Select Calendar. Select Options. Select View... and then Today to view the current day's entries or select Day view to view the selected day's entries. To view the current day's entries In the Today view each event is displayed on one line as follows: a graphic representation ( ) if an alarm has been set, the event starting time, the first part of the event title, Red events indicated that two or more events clash. The following actions are available: ACTIONS PURPOSE To move down to the next event or loop back to the first one To move up to the previous event or loop to the last one To move to the previous day To move to the next day 14- Tools An Options list is available. It allows you to change the current View..., Create a new event or Modify an event, Send it by... infrared port and SMS, Export... it, Delete one event or Delete all events. To view weekly entries 1 2 3 4 5 Press the [Menu/T9] key. Select Tools. Select Diary. Select Calendar. Select Options. Select View... and then Week view. The week's events are displayed in chronological order. Each event is represented as a bar (its length depends on its duration. Red indicates clashes. Purple indicates that the alarm has been activated). The following actions are available: ACTIONS PURPOSE (short press) (long press) (short press) (long press) To move down to the next time interval To move up to the next time interval To move to the previous day To scroll to the previous week To move to the following day To scroll to the following week An Options list is available. It allows you to change the current View..., Create an event, Export... the Events in a defined period/All events or Delete all events. To view monthly entries 1 2 3 4 5 Press the [Menu/T9] key. Select Tools. Select Diary. Select Calendar. Select Options. Select View... and Month view. The whole month is displayed. If the selected month is the current one, the date is displayed in a different colour. Colours are used to indicated the days (and alarm activation) of the stored events.The following actions are available: ACTIONS PURPOSE (short press) (long press) (short press) (long press) To move down within the current display To move up within the current display To move to the previous day To scroll to the previous month To move to the following day To scroll to the following month An Options list is available. It allows you to change the current View..., Create an event, Export... the Events in a defined period/All events or Delete all events. 15- Tools Tasks list This feature allows you to store up to 100 tasks to be done (To do), scheduled with a start and a due date, with or without a reminder alarm. To enter a new task 1 2 3 4 Press the [Menu/T9] key. Select Tools. Select Diary. Select Tasks list. Select New task and enter the required information. An empty task card is displayed with the following fields: a title (up to 10 characters), a description (up to 50 characters), a start date, a due date, an audio alarm which can be activated at your specified time. 5 6 1 2 3 4 Enter or select the requested data. Confirm each entry by pressing OK . Select Save to confirm data storage. Press the [Menu/T9] key. Select Tools. Select Diary. Select Tasks list . Select Current tasks or Elapsed tasks. To display a tasks list The tasks are displayed in a list, ordered by date. If an alarm is activated for a task is displayed. An Options list is available. It allows you to create a New task, Modify the current task, Send a task by... Infrared port or by SMS, to Export... Tasks in period or All tasks, to Delete the current task or to Delete all tasks period. Sending an event/a task The Send by... option allows you to directly send the selected file via the Infrared port, by SMS or by Mail. 1 2 Press Options (from the Day, Week or Month view). Scroll down and select Send by... Select Infrared port, SMS or Mail (if available), then proceed as usual when using these features. Exporting an event/a task The Export... option allows you to create a file so as to exchange events or tasks with another device such as a PC or another mobile. The created file can contain all the events or tasks stored in the calendar or in the tasks list (select All events/tasks) or in a time interval (Select Events/Tasks in period). 1 2 3 Press Options (from the Day, Week or Month view). Scroll down and select Export... Select All events/tasks or select Events/Tasks in period then define the time period (Between / And) and select Export. The exported file is stored in the Others folder of the Fun & Media box menu. You can then send it to another device (please see "Others", page 67). 1. The exported calendar or tasks list item is stored as a .vcs file. 2. Once your task/event is exported to the Others folder, a confirmation screen is displayed. Then you can directly send your task/event by selecting the Send by... option. Alarm notification The alarm notification screen is displayed at the specified time according to the event or task to which it relates. If it is not acknowledged, the alarm stops ringing after 60 seconds. It automatically restarts after a snooze time until it is stopped or up to the start/finish time and date of the event/task. If the phone is off at alarm time, it automatically switches on. If the phone is locked or if the PIN setting is on, the phone returns to this locked state after the alarm has rung until you use it. 1 Press Valid to acknowledge the alarm or press Snooze to repeat the alarm after the snooze period. Snooze is not available on a task alarm. 16- Tools Storage used This feature displays the number of Diary registered events and tasks. The following actions are available in the Options menu: ACTIONS PURPOSE Delete events Delete tasks Delete all events Delete all tasks To delete the events of the defined time period. To delete the tasks of the defined time period. To delete all the events stored in Calendar. To delete the tasks stored in the Diary. Calculator This feature allows you to make simple calculations using + (plus), - (minus), * (multiplication), / (division) and % (percentage) functions. If the currency converter is activated, numbers can be converted during calculations. To use the calculator 1 2 Press the [Menu/T9] key. Select Tools. Select Calculator . The phone is ready to perform simple calculations. Press keys to to enter numbers. Press the multitap (for further details on the multitap text entry method please see "Entering text / Edition mode", page 22) to get +, -, * and / symbols. Use the multitap to enter decimal points or %. Press the [Clear] key during a calculation to correct an entry. Press = to get the operation result. Example 144 x 12 = 1728 key sequence display 144 Press 3x * 12 = 1728 In the above example, pressing = again calculates 1728 x 12 = 20736 Pressing the [Clear] key deletes the result. The % function can only be used (entered) as the last operation during a calculation. e.g.250 - 10% = 225 An integrated currency converter facility is also available. See Currency converter below. using the currency converter £ - : Example 154 + 3 = £ 97.1374 key sequence display Select Curr. 95.2813 + 1.8561 = 97.1374 1. This example was made on the basis of the following exchange rate: 1 = £0.61871 2. The Currency converter feature can be accessed from the Calculator and from the Currency converter submenus. 17- Tools Currency converter This feature allows currency conversion. The currencies and exchange rates must be entered prior to use. The conversion is calculated on the per unit exchange rate of the second selected currency. To select the currencies and the exchange rate 1 2 3 4 5 Press the [Menu/T9] key. Select Tools. Select Currency converter. Select Settings. Enter the first currency name (e.g. Euro). Press OK. Enter the second currency name (e.g. Dollar). Press OK. Enter the exchange rate using to enter a decimal point. Press OK to validate the entry. Press Save to confirm data storage. To calculate the conversion between the selected currencies 1 2 3 4 5 Press the [Menu/T9] key. Select Tools. Select Currency converter. Select one of the first two options. Enter the amount to be converted. Press to insert a decimal point if needed. Press OK. The converted amount and the exchange rate information are displayed. Alarm clocks This feature allows you to set up to three alarm clocks. These alarms can be set to be played at different times and to be played once, daily, or on selected days. To set alarms 1 2 3 Press the [Menu/T9] key. Select Tools. Select Alarm clocks. Select Alarm 1, Alarm 2 or Alarm 3. Select On then enter the alarm time or press OK to validate the displayed time. Select Repetition (1, 2 or 3 according to the Alarm you have previously set). Select Once (the alarm will be played once only), Daily (the alarm will be played every day at the same time) or Weekdays to choose the required day(s) by pressing OK, then select Valid to return to the Alarm clocks screen. Press Save to confirm the selection. is displayed when reverting to the standby display. If the phone is off at alarm time, it automatically switches on. If the phone is locked or if the PIN setting is on, the phone returns to this locked state after the alarm has rung until you use it again. If the alarm is acknowledged but not validated after the 3rd (and final) alarm, the alarm indicators remain on the display for up to 15 minutes (the mobile then either goes back its previous state, 'on' or 'off'). 1. If a call is in progress at alarm time a 'Call in progress' alert beep sounds and a visual alert is displayed every 3 minutes. Validate or acknowledge the alarm in the usual way. 2. If several alarms are set to be played at the same time, the alarm tone is played once only. Any action performed on the mobile to acknowledge the alarm tone is then applied to all the alarms. To use the alarm as a Reminder or a Snooze Alarm 1 Press No ring, or any other key (except Valid. and OK) to snooze the alarm. The alarm icon remains on the display and the alarm starts ringing again 3 minutes later. Or press Valid or OK to acknowledge the alarm and stop the alarm clock process. Press the [Menu/T9] key. Select Tools. Select Alarm clocks. Select Off. Press Save to confirm the selection. To turn the alarm Off 1 2 3 18- Tools Infrared port The infrared port allows you to exchange data between the mobile and other devices (provided they have an infrared port). You can for instance download or send files such as videos, images for your Standby display (see "Pictures", page 57 ), send or receive name cards,... You can send files via the Infrared port from several menus or sub-menus (e.g. by selecting Options after having captured a picture, then by selecting Send by... Infrared port). To initiate a transfer via the infrared port, your mobile must be facing another infrared port. Both ports can then be opened and synchronised. The requested transfer can then be performed. Files (e.g name cards) are transferred one by one. Opening the Infrared port 1 2 3 Place your mobile directly opposite the infrared port of the other device. Press the [Menu/T9] key. Select Tools. Select Infrared port. The infrared port opens and the mobile automatically acknowledges the state of the opposite infrared port. 1. If the infrared port is already open, selecting the Infrared port item closes it. 2. The Infrared port cannot be opened while using the Camera or the Video applications. The Infrared port is automatically closed when accessing the Camera or Video applications. Transferring a name card via the infrared port You can transfer a name card via the infrared port: 1 2 3 4 Place your mobile directly opposite the infrared port of the other device. Open the infrared port of the other device. Select the card you wish to transfer as explained in the section "Viewing and calling Phone book numbers", page 36. Select Options. Select Send by... Infrared port. The infrared port opens and the transfer is performed. Using your mobile as a modem You can use your mobile as a modem for other devices (PC, PDA,...) via the infrared port (on both devices) or via a PC cable. In order to activate a connection, a standard modem driver must already be installed in the other appliance: 1 2 3 Install the PC cable or open the Infrared port on your PC or PDA. Install the modem driver. Configure the PC according to the instructions given with the modem driver. Please enter the following parameters: - Flow control: Hardware - Data Bits: 8 - Parity: No parity - Stop Bit: 1 stop Bit - Speed: 921 600b/s 1. The PC cable may not be supplied with your mobile. Please ask your retailer for an M430i compatible PC cable. 2. The compatibility between GPRS and i-mode features is operator dependent. Your mobile: 1 Plug in the PC cable (please refer to the Getting Started with your M430i booklet). Open your mobile Infrared port. If your mobile is set to Modem mode, (Please see "Operation mode", page 94) all incoming calls are rejected. If your mobile is not set to Modem mode, your Internet connection may be interrupted by incoming calls. or: 1 Once both devices are ready, the Internet connection can be activated (without any action being performed on your mobile). 19- Tools MESSAGES/TEXT EDITING his section describes the contents of the Messages menu and contains full information on the Short Message Service. Other types of messages can be sent and received via your mobile. The Short Message Service (SMS) allows you to send or receive text messages to or from other mobile phones. You can store, edit and forward messages as well as save any of the numbers, mail addresses, web site addresses they may contain. These SMS are stored on the phone memory; they may also be stored in the SIM card if they are sent by a service provider. You can access the Messages menu by pressing and holding the [Mail] softkey from the standby display. This chapter mainly deals with the SMS and Broadcast message types. Please refer to the i-mode section (page 73) for full information on Mail and MMS. T Contents of the Messages menu The Messages menu includes the three message types that are available on your mobile: SMS, Mail/MMS, Broadcast messages. To select one of these message types: 1 2 Press the [Menu/T9] key. Select Messages Select SMS, Mail/MMS or Broadcast. A number is displayed on the SMS and Mail/MMS lines, on the right of the screen. It indicates the number of unread received messages in the corresponding Inbox folder. From the idle screen, press and hold the left softkey (underneath Mail). Select SMS, Mail/MMS or Broadcast. A number is displayed on the SMS and Mail/MMS lines, on the right of the screen. It indicates the number of unread received messages in the corresponding Inbox folder. or 1 2 Accessing the SMS menu You can access the SMS menu via three ways. This chapter describes the SMS sub-menu and features via the [Menu/T9] key, but you can use any of the following paths to access this submenu. 1 2 Press the [Menu/T9] key. Select Messages Select SMS. From the idle screen, press and hold the left softkey (underneath Mail). Select SMS. From the idle screen, press the right softkey (underneath i-mode). Select SMS or press . or 1 2 or 1 2 Reading a received SMS message When the phone receives an SMS message, a new SMS alert beep or melody sounds and is displayed on the Standby display. The message is automatically stored in the phone or in the SIM card. A flashing indicates that the SIM or the phone memory are full and cannot store any further messages. Delete messages to allow new messages to be delivered. 1 2 Press Read to read new messages (from the standby display only). Press Options to View, Reply, Reply (+text), Delete, Delete all, Forward, Send as mail, Move to SIM, Numbers & addresses (to store or call the number(s) contained in the SMS header or text, or store the mail or web address contained in the message text. All the message characters that are displayed between «» can also be stored on your mobile). 1. According to the selected item, another Options list may be available so that you can proceed with the action. 2. If you select a melody as a new SMS alert (please see "Melodies", page 60), press the [OK] key to acknowledge receipt of the new incoming SMS and to stop the melody. 20- Messages/Text editing Reading stored SMS messages 1 2 3 4 Press the [Menu/T9] key. Select Messages. Or press and hold the Mail softkey. Select SMS. Select Inbox or SIM archive then select Received messages to display the message list. Use the arrow key to scroll up and down and access the message you want to read. Select OK or Options/View to read the message text. Unread messages are indicated by the read are indicated by . icon + bold text. Messages that have already been Moving messages to SIM It is possible to move a message from the Inbox or the Outbox to the SIM memory. However, according to the message size, the message may be truncated (the 160 first characters only are moved to the SIM memory). The sending date (for sent messages) and the 'Copy to' addressees are lost when moving the message to the SIM memory. To move a message to the SIM memory: 1 2 3 4 5 Press the [Menu/T9] key. Select Messages. Select SMS. Select Inbox or Outbox. Choose the message to be moved and select Options. Select Move to SIM. Forwarding messages You can forward a received message to other people/number(s): Press the [Menu/T9] key. Select Messages. Select SMS. Select Inbox or SIM archive/Received messages. Select the message to be forwarded and select Options. Select Forward. Press OK. Select the To field and select one of the displayed names or in the Phone book list select Options then New or Other folder if you want to send your message to another mobile number. Press OK to validate. 7 In the Text field enter the message text (see "Entering text / Edition mode", page 22) or select one of the models (Models) and press OK. 8 If you want to send the message to several addressees, enter one or several phone numbers/ names in the Copy to list (up to 4 more addressees) and press OK then Valid to return to the previous screen. 9 Select Options. 10 Select Send, Store & send or Store. 11 A warning message displays the number of SMS needed to send the message if it is more than one. Select Go on if you want to send the message or select Cancel if you do not want to send it or if you want to amend your message. 1 2 3 4 5 6 Activating or deactivating the message alert tone Each time a message is received, a new SMS alert tone sounds. To activate or deactivate this tone: 1 2 3 4 Press the [Menu/T9] key. Select Messages. Select SMS. Select Settings. Select Reception alert. Select On or Off. You can personalise the Message alert tone (please see Melodies, page 60). 21- Messages/Text editing Preparing the phone to send SMS messages Before sending your first SMS or if you want to register a new profile, the network SMS centre number (obtainable from your service provider) must be stored: FIELDS DESCRIPTION DEFAULT Name Message centre Format Validity period 1 2 3 4 5 To enter the profile name. To enter the centre number. To set the message format: text, voice, fax or paging. Time the message remains at the message centre until delivered. Profile1 Empty Text Maximum Press the [Menu/T9] key. Select Messages. Select SMS. Select Settings. Select Sending profile. Enter the message centre number or select a template (if several available) then enter the following fields (operator dependent). You may not be allowed to change your sending profile (format and validity period). Please contact your service provider for further details. 6 Select Save to validate. The SMS centre number may already be available in your SIM card and may be automatically displayed. If you want to select a Sending profile for your message: 1 2 3 4 5 Press the [Menu/T9] key. Select Messages. Select SMS. Select Settings. Select Sending profile and select the profile you want to use. Select Options. Select Select. Entering text / Edition mode All the settings described in this part are to be done from an edition screen. Some features and functions (storing names in the Phone book, typing SMS text messages, writing a mail, Tools, Settings,...) require you to know how to enter and edit text in the display, to insert special characters or mail icons, to copy and paste text, etc. Four edition modes are available. They are indicated on the left-hand side of the screen by in lower case mode, by in upper case mode, by in next character toggle mode (the first typed character is an upper case then the others are lower cases) and by in numeric mode. Text and figures and alphabet characters can then be entered or edited directly from the keypad. To switch from one mode to another: 1 2 Select Options Select Lowercase if the current mode is upper case mode or select Uppercase if the current mode is lower case. When in lower case, on T9 mode or on Multi-tap mode, the Next character toggle mode is automatically set when required, according to the context (i.e. after a full stop or after ? or ! followed by a space for instance). There are three input modes to enter text or figures: the Multi-tap (or Multipress) key method, the quicker intuitive method, called T9 text input and the Numeric mode (to type numbers). To select an edition mode: 1 Press the [Menu/T9] key to swap modes (T9 to Multi-tap/Multi-tap to T9). Select Options Select Input mode. Select T9, Multi-tap or Numeric. or: 1 2 3 22- Messages/Text editing When in T9 mode, is displayed on the upper part of the display to indicate that T9 is the current mode. When on Multitap mode, is displayed on the upper part of the display to indicate that Multitap is the current mode. The multitap/multipress method A brief press on a key displays the first character associated with the key and shows the other available characters at the top of the display. Here is the list of the available characters (the available characters list is language dependent): KEY CHARACTER Lower case Upper case . , - ' @ : ?/_1 abc2 ABC2 def3 DEF3 ghi4 GHI4 jkl5 JK L 5 mno6 MNO6 pqrs7 PQRS7 tuv8 TUV8 wxyz9 WXYZ9 0 0 Swap between the Upper case, Lower case and Numeric edition modes. Short press: to enter a space. Long press: to access special characters. Short press: moves the cursor through the text one place to the left or to the right. Long press: moves the cursor to the text beginning or end. To move the cursor to the text beginning or end. Swap between the Multitap/Multipress method and the T9 text input. To enter text, press the key bearing the required character until it appears in the display. Holding the key displays the figure corresponding to the key. If you need to use two characters from the same key, wait for a few seconds after entering the first character (until the key characters on the upper part of the screen are cleared) or press the right arrow key before pressing the key again. Correct mistakes by a short press on the [Clear] key. Holding the [Clear] key deletes all the text. Use the left or right arrow keys to move the cursor in the text. Multitap method Example To type Card: Press the [Menu/T9] key and select Messages. Select SMS. Select Write new. Fill in the To field (see "Sending a new SMS message", page 26). In the Text field, press on the [Menu/T9] key until is displayed, or select Options, then Input mode and choose Multi-tap. Press briefly three times, C is displayed. Press once, a is displayed Press three times, r is displayed Press once, d is displayed. The word Card is now displayed. 23- Messages/Text editing The T9 method A press on the [Menu/T9] key allows you to swap between T9 text entry and the Multitap method. 1 2 3 4 5 Press the key bearing the required letter once only (the requested character may not be displayed first). The active word changes as you enter text. Enter all the word characters up to the end of the word. If the right word is not displayed when all the characters have been entered, press until you get the required word. If the requested word does not correspond to the one displayed, press the [Menu/T9] key to swap to the Multi-tap mode and enter the correct letters. Use the [Left] or [Right] arrow keys to move the cursor around the text to insert or delete characters. Example To write card: Press the [Menu/T9] key and select Messages. Select SMS. Select Write new . Fill in the To field (see "Sending a new SMS message", page 26). In the Text field, press on the [Menu/T9] key until is displayed, or select Options, then Input mode and choose T9. Press , A appears. Press , Cc appears. Press , Car appears. Press , Case appears. If the displayed word is not the one you want, press as many times as necessary to view Card. To insert a text symbol such as :) or :-) or press to change the symbol to :( or :-( etc. two or three times. Press as many times as necessary Inserting special characters, i-mode pictographs or text You can insert special characters, i-mode icons (pictographs), pre-stored text models,... while using the edition mode. Some of the elements listed below are examples and may vary according to the edition context. To insert special characters: 1 2 Select Options, then select Insert. Select Special characters. Scroll up, down, left or right and press OK to select the required special character. or: 1 2 Press and hold the key to display the special characters list. Scroll up, down, left or right and press OK to select the required special character. The symbol may not be displayed from all edition modes. It allows you to go to the following line. To insert i-mode pictographs: 1 2 3 Select Options. Select Insert. Select Pictographs. Scroll up, down, left or right as many times as necessary to reach the required icon then press OK to validate your choice. You can choose those icons from any of the six available icons pages (scroll down as many times as necessary to reach the following pages). This option is only available from the Mail and MMS edition modes. 24- Messages/Text editing To insert a text model: 1 2 3 Select Options. Select Insert. Select Text models. Select one from the list. For more information on this feature, please see "Creating text models", page 26. This option is only available from messages edition modes (it is not available in numeric edition modes, while writing a mail address, etc.) Text copy and paste You can copy a text or part of a text so as to paste it into another edition context (or into the source edition context). The copied text remains stored in the mobile memory until the mobile is turned off or until another Copy action is performed. You can therefore paste it as many times as you wish. To copy part of a text 1 2 3 From an edition screen (e.g.: while writing a mail, an MMS, an SMS, a Phone book card,...), select Options. Select Copy (you can also access the Copy option from the edition screen by pressing the [Up] side key). Scroll right or left ([Right]/[Left] arrow keys or up/down side keys) to select the required part of the text to be copied (the selected text is displayed in blue colour). Select Copy, press OK or press the [Up] side key. The selected text is copied into the mobile memory. 1.The Copy option is not available in numeric edition modes. It is however available while using the numeric mode in an alpha-numeric edition context. 2. The Copy all option only is available in numeric edition mode. It therefore copies the full displayed number. To copy all the text 1 2 From an edition screen (e.g.: while writing a mail, an MMS, an SMS, a Phone book card,...), select Options. Select Copy all. The whole edition screen content is copied into the mobile memory. From an edition screen (e.g.: while writing a mail, an MMS, an SMS, a Phone book card,...), press and hold the [Up] side key. The whole edition screen content is copied into the mobile memory. From an edition screen (e.g.: while writing a mail, an MMS, an SMS, a Phone book card,...), move your cursor to the required location. Select Options. Select Paste. The previously copied text is pasted. From an edition screen (e.g.: while writing a mail, an MMS, an SMS, a Phone book card,...), move your cursor to the required location then press the [Down] side key. 1. If the copied text is too long to be inserted into the available space on the target edition mode (e.g. maximum SMS allowed size reached), the text to be copied is not fully pasted. 2. You cannot paste a copied text if the text characters are not supported by the target edition context (e.g. an alphanumeric text in a numeric edition context, such as a phone number, or a text bearing i-mode pictograph in an SMS edition screen). or: 1 To paste the copied text 1 2 or: 1 Selecting an edition language You may wish to select an edition language different from the language set on your mobile. Doing so, the required character sets are available while using the keypad. The required T9 editor may also be available. To choose an edition language: 1 2 3 From an edition screen (e.g.: while writing a mail, an MMS, an SMS, a Phone book card,...), select Options. Select Edit. language. A list bearing the available languages is displayed. Press OK to select the required language and return to the edition screen. The T9 edition mode may not be available for all languages. 25- Messages/Text editing Tips and Operation KEY ACTION Short press: to switch mode (from T9 or Multitap) to lower case, upper case or numeric mode. Long press: to insert a capital letter while writing in lower case. Only the first letter entered is upper case, the following ones are lower case (e.g.: to write a surname). Swap between the Multitap/Multipress method and the T9 text input. Clear or backspace Short press: to enter a space. Long press: to access special characters. Another matching word Smart punctuation Short press: moves the cursor to the beginning or end of each word. Long press: moves the cursor to beginning or end of the text. To move the cursor to the beginning or end of the text. Creating text models You can create a set of messages to be used as models. These texts can contain up to 50 characters and text can be added when you want to use them. These templates are stored in the mobile memory. To create text models: 1 2 3 4 5 Press the [Menu/T9] key. Select Messages. Select SMS. Select Text models. Choose any blank template ([...]) and press OK. Enter the template text and press OK. Editing a text model You can modify a text model: 1 2 3 4 5 Press the [Menu/T9] key. Select Messages. Select SMS. Select Text models. Select the text model to be modified and press OK. Edit the text and press OK. Sending a new SMS message You can send message texts (up to 918 characters). The standard size for an SMS is 160 characters (your service provider charges you according to the number of SMS used to send your message). The icon (1 = number of SMS used - it is updated while writing your message and shows the number of SMS needed to send your message) is displayed on the left corner of the screen. To send SMS from the Menu: 1 2 3 4 5 Press the [Menu/T9] key. Select Messages. Select SMS. Select Write new. Select the To field and choose one of the displayed names, or in the Phone book list select Options then New or Other folder if you want to send your message to another mobile number (directly enter the number). Press OK to validate. In the Text field, enter the message text (see "Entering text / Edition mode", page 22) or select one of the models (Text models ) and press OK. 26- Messages/Text editing 6 7 8 9 If you want to send the message to several addressees, enter one or several phone numbers/names in the Copy to list (up to 4 more addressees) and press OK then Valid to return to the previous screen. Select Options. Select Send, Store & send or Store. A warning message displays the number of SMS needed to send the message if it is more than one. Select Go on if you want to send the message or select Cancel if you do not want to send it or if you want to amend your message. If you have registered an automatic signature, the number of characters used is automatically added to the message length. To send SMS from the standby display: 1 2 3 4 Press the [left] arrow key to access the Phone book. Scroll to one of the available names or numbers. Select Options. Scroll down and select Send a message... Select SMS, then proceed as described above. Press and hold the key. Select Write new, then proceed as described above. or: 1 2 Signature You can register a signature to be automatically added to your text messages. The signature is not displayed when typing the message text but it is displayed on message reception by the addressee. The maximum size for the signature is 30 characters. If the message text to be sent already contains 918 characters, the signature cannot be added. To register a signature: 1 2 3 4 5 6 7 Press the [Menu/T9] key. Select Messages. Select SMS. Select Settings. Select Signature. Select Insert in message. Select Yes. Select Text and enter your signature text. Select Save to store your signature. Outbox and SIM archive emitted messages The Outbox contains stored sent messages (delivered or undelivered). The SIM archive contains unsent draft messages and stored sent messages (delivered or undelivered). These messages can be selected from the outbox or SIM archive menu and can be modified and resent as new SMS messages. To select one of these messages: 1 2 3 4 Press the [Menu/T9] key. Select Messages. Select SMS. Select Outbox or select SIM archive then Emitted messages and use the [Up] or [Down] arrow keys to scroll to the required message. Messages are either 'transmitted' or 'to be sent'. Press Options to View, Delete, Delete all (for Outbox messages only), Status (for sent messages only) Send, Send as mail, Edit, Move to SIM (for outbox messages only), Move to phone (for SIM archive emitted messages only), Numbers & addresses (to store or call the number(s) contained in the SMS header or text) or Details. 27- Messages/Text editing Draft messages The Drafts folder contains the written messages that were not sent. You can edit these messages and/or send them. To select one of these messages: 1 2 3 4 Press the [Menu/T9] key. Select Messages. Select SMS. Select Drafts and use the [up] or [down] arrow keys to scroll to the required message. Press Options to View, Delete, Delete all, Send, Send as mail, Edit, Edit a copy, Move to SIM (for outbox messages only), Numbers & addresses (to store or call the number(s) contained in the SMS header or text) or Details. Status request If a status is requested on a sent message, a status request is sent to the network (must be network supported). If the status is requested on a delivered message, the date and time of delivery may be shown. The network then answers by sending a status report (SR) back to the phone. Press OK to acknowledge it. To activate the status request 1 2 3 4 5 6 Press the [Menu/T9] key. Select Messages. Select SMS. Select Settings. Select Message config. Select Delivery report and select On. Select Save. To request a reply A reply to your message can be requested from your correspondent. If you activate this feature, you will be charged for the cost of the reply message. The availability of this feature is operator dependent. 1 2 3 4 5 6 1 2 Press the [Menu/T9] key. Select Messages. Select SMS. Select Settings. Select Message config. Select Reply requested and select On. Select Save. Press Options. Send again, Clear, Associated message or Delete message is displayed. Select the required action. To read the sent message, delete or re-send it when receiving the status: Storage consumption The storage status for SMS messages can be consulted. To view the number of messages stored, the total available space on the Phone memory and on the SIM card: 1 2 3 4 Press the [Menu/T9] key. Select Messages. Select SMS. Select Storage used. The SMS memory used is displayed. Scroll down to access the SIM archive. Select Details for more information on the Phone and SIM stored messages (use [up] and [down] arrow keys to scroll to the required information). 28- Messages/Text editing Broadcast - cell broadcast (CB) messages These messages are broadcast by the networks to GSM users and may provide general information about local area dialling codes, weather reports, traffic, news, etc. Each type of message is numbered, allowing you to select the type of information you wish to receive. Up to 5 types of messages can be programmed into the selection list. 16 standard message types are pre-programmed into the phone for your selection. New message types can be programmed into the selection list using the 3 digit cell broadcast type number. Contact your service provider for details about the type of messages they broadcast. Before you activate the broadcast message service, you must enter at least one message type in the selection list. Entering a message type in the selection list 1 2 3 4 5 6 1 2 3 4 Press the [Menu/T9] key. Select Messages. Select Broadcast. Select Message types and select one of the empty types ([...]). Select OK. Select Modify by list (or Modify by code if the type number is known). Select the message type(s) you wish to receive and select Valid. Select Save to store your setting. Press the [Menu/T9] key. Select Messages. Select Broadcast. Select Reception and select On or Off. Select Save to store your setting. Activating / deactivating the broadcast service Reading broadcast messages Broadcast messages are displayed whilst the phone is on standby. If a broadcast message is received whilst in conversation or operating the menu, it only becomes visible once the mobile reverts to the standby display. A message can contain up to 93 characters and may be displayed on several pages. Options on message display Press the [Clear] key to clear the CB message displayed. Press the [Call] key to dial the number contained in the message. Press Options to display the following menu: OPTION ACTION Delete Delete All Numbers & addresses Broadcast Off To delete the current message To delete all the received CB messages To display all phone numbers contained in the message text and dial or store them in the Phone book if required. To deactivate cell broadcast. Activating/deactivating the alert tone An alert tone can be set to beep every time a new or updated broadcast message is received. 1 2 3 4 Press the [Menu/T9] key. Select Messages. Select Broadcast. Select Reception alert and select On or Off. Select Save to store your setting. Broadcast language All the broadcast messages can be displayed in several languages. To select a language: 1 2 3 4 Press the [Menu/T9] key. Select Messages. Select Broadcast. Select Language and select one of the available languages. Select Save to store your setting. The availability of this feature is network dependent. 29- Messages/Text editing CALLS & TIMES Calls & to check the individual incoming and Access thecalls, theTimes menurecordedcall, details ofcall time for all outgoing outgoing duration of the last the total and incoming calls or to play the calls. Call logs This feature stores details (identity, time and date and call duration) about the last 20 numbers dialled, the last 20 unanswered calls and the last 20 received calls. The calls log can be activated for Line 1 and Line 2 (Line 1 is your main line. Line 2 availability is subscription dependent). 1 2 3 Press the [Menu/T9] key. Select Calls & Times. Select Call logs. Use the [Up] or [Down] arrow keys to scroll through the calls list. The last number dialled , received or unanswered is displayed at the top of the list. The caller's name is displayed if it is registered in one of the Phone books (if not the phone number is displayed). If your subscription does not have Caller Line Identification (CLI) 'Unknown number' is displayed. If the caller has with withheld his number, 'Withheld number' is displayed. Press the [Call] key to call the selected number. Press Options to access the following menu: ITEM ACTION Call Store Delete Delete all Edit Send SMS To call the selected number. To store the number in the Phone book. To delete the entry. To delete all entries. To edit the displayed number. To send an SMS message to the selected phone number. Use the [Up] or [Down] arrow keys to select the required option and follow the instructions displayed. Press the [Call] key from the standby display to access the call logs list. Call timers The voice, Modem and GPRS call information for Line 1 and Line 2 is stored in the Call timers menu. 1 2 3 4 Press the [Menu/T9] key. Select Calls & Times. Select Call timers. Select Show. Use the [Up] or [Down] arrow keys to view all the timer information. If the call timers were reset (see "Call timers - reset", page 31) the date of the latest counter reset is displayed. The call type and the accumulated times of outgoing and incoming calls are displayed. Selecting Details displays information on calls made on your home network, on National roaming and on International roaming. If Line 2 is active too, 'All Calls' for Line 1 and Line 2 are displayed separately. 30- Calls & Times Balance information (subscription dependent) This service may be supplied by your service provider. It allows you to view the remaining airtime balance on your phone line. Please contact your service provider for more information. If your subscription allows access to this information: 1 2 3 4 Press the [Menu/T9] key. Select Calls & Times. Select Call timers. Select Balance information. Select Call or Set number. When selecting Call, if the balance information number is already stored, a call is sent to the balance information centre. If no number is stored, select Set number and enter it. Press OK to store the number, then select Call to call the information centre number. Reminder - call duration You can set a duration reminder to beep regularly to remind you of the time spent on your call. The frequency can be any multiple of 1 minute (up to 59 minutes) and a beep is emitted 10 seconds before you reach the set limit. 1 2 3 4 5 6 Press the [Menu/T9] key. Select Calls & Times. Select Call timers. Select Reminder. Select On to activate the Reminder. Enter the reminder interval. Press OK to validate the entry. Call timers - reset This feature allows you to reset the call timers. The 4 digit lock code is required to reset the call timers (default lock code: '0000'). 1 2 3 4 5 Press the [Menu/T9] key. Select Calls & Times. Select Call timers. Select Reset. Select Yes. Enter the phone lock code and press OK. Call costs - management Some service providers offer an Advice of Charge (AoC) subscription service allowing you to view the latest call cost, the total calls cost and the remaining balance on your account (once a 'credit limit' has been set ). To display these, you must first set a currency value and enter an average cost per unit (only calls units are displayed if the cost information is not stored). To set a currency value per Unit: 1 2 3 4 5 6 7 1 2 3 4 Press the [Menu/T9] key. Select Calls & Times. Select Call costs. Select Display cost type. Select Currency. The current currency unit value is displayed. Select Modify. Enter your PIN 2 code and press OK. Enter the currency name (up to 3 letters). Press OK to validate. Enter the unit cost (e.g.: 0.15 Euro per minute). Press OK to validate. Press the [Menu/T9] key. Select Calls & Times. Select Call costs. Select Display cost type. Select Units. When the cost type is set to Units, the credit limit and the remaining credit are shown in units. To set the call cost type to Units: 31- Calls & Times Setting the credit limit (subscription dependent) You may also be able to set a credit limit to your calls. Once the credit limit has been reached, no more chargeable outgoing or incoming calls are allowed. You can however still make emergency calls. The PIN2 code is required to set the credit limit. 1 2 3 4 5 Press the [Menu/T9] key. Select Calls & Times. Select Call costs. Select Credit limit. The display indicates the current credit limit set. Select Edit. Enter your PIN 2 code and press OK. Enter the credit limit (use to enter a decimal point for currencies). Press OK to validate. When a credit limit has been set, the selection from the 'Credit limit' display is Edit or Set no limit. Show costs 1 2 3 4 Press the [Menu/T9] key. Select Calls & Times. Select Call costs. Select Show. Use [Up] and [Down] arrow keys to display the Last Call and All Calls and show the Remaining credits. The remaining credit is shown in either units or currency, as set by Cost Type menu above. Call costs - resetting all costs to zero To reset all call costs to zero: 1 2 3 4 5 Press the [Menu/T9] key. Select Calls & Times. Select Call costs. Select Reset. Select Yes. Enter the PIN 2 number and press OK. Recorded call This sub-menu allows you to play the recorded phone calls. If several phone conversations have been recorded, they are played one after another. 1 2 Press the [Menu/T9] key. Select Calls & Times. Select Recorded call. In compliance with European regulations, you are obliged to inform your correspondent before recording a phone conversation. Line selection Some operators support the use of a second line. You may then have two mobile phone numbers (e.g. a business line plus a personal line). To use them you need to select the line to be used. 1 2 3 Press the [Menu/T9] key. Select Calls & Times. Select Line selection. The current line selection is displayed. Use the [Up] and [Down] arrow keys to scroll to the required line. Press OK to validate. 1.The Line selection sub-menu may not be available on your mobile. Please contact your service provider for further details about this service. 2. Line 1 and Line 2 can be named (Office and Home for instance). Refer to My number menu (see "My number(s) display", page 38). Whichever line is selected to send calls, incoming calls can still be received on either line. 32- Calls & Times PHONE BOOK hone numbers can be stored in the mobile memory and in the SIM card memory. - The mobile memory can store up to 500 'extended' cards (called 'Phone book cards'). These cards allow you to store different information types: family name, first name, home number, mobile number, work number, fax number, two mail addresses, postal address, business information, voice tag, group name, card related melody and an associated icon, picture or video. - The SIM card memory capacity may vary according to your operator or service provider. The SIM memory allows you to store one name, one phone number and one voice tag per card. Both the SIM and the phone memories are searched when reading the Phone book contents, unless you have previously selected a folder to be scanned when accessing the Phone book (please see "Sorting the Phone book entries so that they can be viewed as separate folders", page 36). P Press the [Phone book] key or the [Left] arrow key to directly access the Phone book from the standby display. Storing names and telephone numbers Names and numbers can be stored directly in the Phone book or copied from different sources such as SMS messages, last dialled number list, etc. There are several ways to store numbers in the Phone books: Phone names card From the standby display: 1 2 3 4 Enter the number. Select Store. Select New phone name. The Home number, Mobile number, Work number,or FAX number list is displayed, thereby allowing you to select a number type. Enter the card requested data and select Save to store the information. Via the menu: 1 2 3 4 Press the [Menu/T9] key. Select Phone Book. Select Add name. Select Phone names. Enter the card requested data and select Save to store the information. The Groups field allows you to identify the caller's type according to entries you have previously set (see "Creating a group of cards", page 37). Updating a stored phone names card from the phone book: 1 2 3 Press the [Menu/T9] key. Select Phone Book. Select Read. Select the required phone name card from the displayed list, then update the required information. Select Save to store your settings. You can only update the Home, Mobile, Work or Fax numbers via this route. The icon leads to the Pictures list. You can therefore select one of the registered images (please see "Pictures", page 57) and link it with your phone card. 1. You can link about 100 images with your Phone book cards. If the images folder is full (images too big), an error message is displayed. 2. The images remain attached to the Phone book cards even if you have deleted them from the Pictures folder memory. You can modify or delete them one after the other via the Phone book cards (see "Editing a Phone book or a SIM name card", page 36). 3. When sending a Phone book card via the infrared port, the image is automatically sent unless the file is protected. 4. The Image failure icon is displayed on incoming or outgoing calls if a problem related to the image has been detected by the mobile. 33- Phonebook SIM names card From the standby display: 1 2 3 4 1 2 3 4 5 6 Enter the number. Select Store. Select New SIM name. Fill in the available fields and select OK to validate your entries. Select Save to store the card. Press the [Menu/T9] key. Select Phone Book. Select Add name. Select SIM names. Enter the name and select OK. Enter the number and select OK. Select Save to store the card. Via the menu: Storing a received number Numbers stored in the last dialled, received, unanswered call information and SMS message locations can also be stored in the Phone book: 1 2 With a last dialled call, received call, unanswered call or SMS message select Options. For an SMS message, select Numbers if the number is contained in an SMS. The message number(s) is/are displayed. Select one if several numbers are available. 2' For received and unanswered calls, select Store. 3 Follow the above mentioned procedure to create a phone name or a SIM name card then select Save to store the card. 1. While entering a number, pressing the [Clear] key once deletes the last character. Holding the [Clear] key deletes the whole number. 2. You can use _ (wild card spaces) to store numbers (wild card spaces cannot be obtained when registering a number from the standby display). When calling a number containing wild card spaces, select the number from the Phone book, select Options or press on the [Call/Send] key and enter the number corresponding to the wild card spaces (=missing figures). 3. The *, +, p (pause) and _ characters- which are accessible by pressing and holding the key when registering a number - can be stored as part of numbers. 4. If the SIM card or phone memory are full, a warning message is displayed on the Phone book selection. Copying names and numbers When consulting your Phone book you can copy any SIM or phone card to another directory. 1 2 3 Press on the [Left] arrow key or press the [Phone book] key or press the [Menu/T9] key then select Phone Book. Select Read. Scroll to one of the items from the displayed list. Select Options. Select Copy, then select one of the available destination directories (Phone names, SIM names, My card). The card content is then automatically copied to the required location. Copying all names and numbers When consulting your Phone book for the first time the 'Copy all SIM names to phone?' message is displayed. Select Yes. You can also, at any time, copy all the names cards from the Phone to the SIM card and from the SIM card to the Phone. 1 2 3 4 5 Press the [Menu/T9] key. Select Phone Book. Select Read. Select Options. Select Copy all. Select Phone to SIM or SIM to phone. All the names are copied unless the SIM card memory does not bear enough free space when copying the Phone entries to the SIM card. A warning message is then displayed. 1. If your Phone book cards bear more than one number (home, mobile, work, fax numbers), the first available number from the list is copied to the corresponding SIM card entry. 2. If the Phone book entries are sorted (please see "Sorting the Phone book entries so that they can be viewed as separate folders", page 36), the Copy all option allows to copy the SIM names in the phone memory or to copy the Phone names in the SIM memory. 34- Phonebook Moving names and numbers When consulting your Phone book you can move any SIM or phone card to another directory. 1 2 3 Press on the [Left] arrow key or press the [Phone book] key or press the [Menu/T9] key then select Phone Book. Select Read. Scroll to one of the items from the displayed list. Select Options. Select Move, then select one of the available destination directories (Phone names, SIM names, My card). The card content is then automatically moved to the required location. Adding a video to your Phone book card You can add a video to each of your Phone book cards. This video is played on receipt of an incoming call. 1 2 3 4 5 Press the [Menu/T9] key. Select Phone Book. Select Add name. Select Phone names. Scroll Down and select Video. Select the required video from the displayed list. Press OK to confirm your selection. Select Save to store your settings. 1. If you add a video and a ringtone to your Phone book card, the video sequence only is played and the ringtone is deactivated on receipt of an incoming call. 2. You can only select a video with an audio track. Otherwise the video is not played on receipt of an incoming call and a warning message is displayed. Adding a picture or an icon to your Phone book card You can add a picture to each of your Phone book cards. This picture can be an icon, an image or a picture you captured 1 2 3 4 Press the [Menu/T9] key. Select Phone Book. Select Add name. Select Phone names. Scroll down and select Picture. Select the required icon or select ture. to display the pictures list, then select the required pic- The icons list allows you to store your card with a symbol or an image that is then displayed together with the caller's name on incoming or outgoing calls. 5 Select Save to store your settings. Setting a melody, a video or a speech note as a ringtone You can set a melody, a video or a speech notes as a ringtone for each of your Phone book cards. If you set a video as a ringtone the audio track of the video sequence only is played. This ringtone is played on on receipt of an an incoming call. 1 2 3 4 5 6 Press the [Menu/T9] key. Select Phone Book. Select Add name. Select Phone names. Scroll Down and select Ringtone. Select Melodies (to set a melody as a ringtone), Videos (to set the audio track of a video sequence as a ringtone), Speech notes (to set a speech note as a ringtone) or No sound (to deactivate the ringtone). Select the required melody, video or speech note. Press OK to confirm your selection. Select Save to store your settings. If no melody is set as a ringtone for your Phone book card, the default ringtone or the melody you set as a ringtone (please see "Ringtone selection", page 84)is played on receipt of an an incoming call. 35- Phonebook Editing a Phone book or a SIM name card From the standby display: 1 2 3 1 2 3 4 5 6 Press the [Left] arrow or the [Phone book] key to access the Phone book. Scroll down to the card you want to modify and select OK. Scroll down to the field(s) you want to modify and amend it/them. Select Save to store the changes. Press the [Menu/T9] key. Select Phone Book. Select Read. Select one of the stored cards. Select Options. Select View. Scroll down to the field(s) you want to modify and amend it/them. Select Save to store the changes. Via the menu: You can create a voice dialling pattern on Phone book cards. This voice dialling pattern can only be recorded in edition mode. Recording a Voice dialling pattern 1 2 3 Press the [Left] arrow key or press the [Phone book] key to access the Phone book. Scroll down to the card you want to access and press OK or select Options then select View. Scroll down to the Voice dialling field and press OK. Select New to record the voice pattern or select Options then Record if a voice pattern is already recorded and you want to change it. Repeat the name until it is stored (minimum = twice). Pronounce it as clearly as possible and in a quiet environment. When the voice patterns match, Stored is displayed. You may have to select the number - the voice dialling pattern has to be attached if several numbers are stored on the card. Select Home number, Mobile number or Work number if you have registered several numbers on a Phone book card. Viewing and calling Phone book numbers There are two ways of viewing and calling entries stored in the Phone book: Directly from the standby display: 1 2 Press the [Left] arrow key or the [Phone book] key to display the Phone book list. To access the required name, either scroll up or down or press a numeric key to access the different letters associated with the key (e.g: press twice to reach the names starting with letter 'B') or type in the required name in the edition area displayed at the top of the screen (you can enter up to 20 characters). Press the [Call] key or select Options then select Call. When typing in the required name in the edition area, the Multitap mode is only available. 3 Via the menu: 1 2 3 Press the [Menu/T9] key. Select Phone Book. Select Read to display the Phone book list, then scroll up and down to the required name or press a numeric key to access the different letters associated with the key. E.g: press twice to access the names starting with letter 'B'. Press the [Call] key or select Options then select Call. 1. Selecting a group from the Folder selection displays the names/phone numbers of the corresponding group. This group is then displayed when next reading the Phone book contents. 2. Selecting Options displays the following menu choice: View, Call, Add name, Delete, Delete all (Phone names or SIM names), Copy, Copy all, Move, Folder selection(to select All names, the Phone names only, the SIM names only or the groups members), Send by... Infrared port or SMS, Send a message...(an SMS, a Mail or an MMS). Some of these options may not be available according to the selected folder. 3. If several phone numbers are stored on a Phone name card, scroll down to the required number and select it before activating the call. The list of Phone book entries is displayed in alphabetical order. Sorting the Phone book entries so that they can be viewed as separate folders You can split the Phone book entries into folders and view either the Phone names, the SIM names or a selected group of entries when reaching the Phone book list. 36- Phonebook 1 2 3 4 Press the [Menu/T9] key. Select Phone Book. Select Read. Select Options Select Folder selection, then choose All names (to display all the folders contents), Phone names (to display the phone cards only), SIM names (to display the SIM cards only) or one of the Groups names (see "Creating a group of cards", page 37) if any. The selected folder remains active for further Phone book reading. Please go over the above procedure to select another folder or display the full Phone book list. Voice dialling You can make a call by using your voice. To create a voice pattern: 1 2 3 4 5 Press the [Menu/T9] key. Select Phone Book. Select Voice dialling. Select New entry. All name entries are displayed. Use the [Up] and [Down] arrow keys to select the card you want to use and press OK. If several phone numbers are registered on a card (e.g. Home number, Mobile number or Work number) select one by pressing OK. You are then prompted to pronounce the name at least twice (pronounce it as clearly as possible).Stored is displayed when both voice patterns match. If the voice patterns do not match, Failed is displayed. Repeat the whole voice registration procedure again. To view the voice dialling numbers list: 1 2 3 4 5 1 2 3 1 2 3 Press the [Menu/T9] key. Select Phone Book. Select Voice dialling. Select List. Use the [Up] and [Down] arrow keys to view the requested entry. Press Options to play the voice pattern, select Play Back, to remove voice tag from the voice dialling list, select Erase, or to create a new voice pattern select Record. Press the [Menu/T9] key. Select Phone Book. Select Voice dialling. Select Delete all. From the standby display, press and hold the call key. Pronounce the name as clearly as possible. The name called as well as an animated icon are then displayed and the call proceeds as normal. To remove all phone numbers from the voice dialling list: To call a phone number using a voice pattern: Free space in the Phone book To view the remaining capacity in the Phone book: 1 2 Press the [Menu/T9] key. Select Phone Book. Select Storage used to get to the Phone names Storage used; press the [Down] arrow key to get to the SIM card Storage used. If available, the free memories in the FDN list are also displayed. Please see "Fixed dialling numbers", page 39 for more information on FDN numbers. Creating a group of cards Groups of cards can be defined for the Phone book. This feature allows you to group certain cards and to play a specific melody on receiving an incoming call from one of the group members. To create a group: 1 2 3 Press the [Menu/T9] key. Select Phone Book. Select Groups. Select any blank template ([...]) and select OK. The following items are displayed: 37- Phonebook ITEM FUNCTION Group name Ringtone 4 5 To enter and store a group name. To select a melody to be used as a ringtone on group member calls. Enter or select the requested data. Press OK to validate. Press Save to store the defined group. Groups' characteristics can be modified or deleted (when in the Groups menu, select OK to amend the settings or select Delete to erase the group). To modify a group: 1 2 3 4 1 2 3 4 Press the [Menu/T9] key. Select Phone Book. Select Groups. Select the group to be modified and select OK then select the group name and/or the ringtone. Select the new parameters (name/melody). Select Save to store your settings. Repeat the Phone names storage procedure (see "Storing names and telephone numbers", page 33) and fill in the Phone names card. Scroll down to Groups and select OK. Select one of the displayed groups from the list. Select Save to store your settings. Groups can only be set for the Phone names cards (not for the SIM names cards). To select a group when storing a number: To view group members: 1 2 3 4 Press the [Menu/T9] key. Select Phone Book. Select Groups. Select the required group name and select Options. Select Members. The group members list is displayed. Please use the same procedure as when in the phone book to reach the required name. My card My card is a specific storage location where you can enter personal data. You can easily access My card and send its contents to another device via the infrared port or SMS. My card contents is identical to the phone cards contents except for the Groups and Voice dialling fields. To enter My card data set: 1 2 3 4 1 2 3 Press the [Menu/T9] key. Select Phone Book. Select My card. Select View and enter the requested information as for a Phone book card (validate each entry by selecting OK). Select Save to store your card. Press the [Menu/T9] key. Select Phone Book Select My card. Select Send by... then select Infrared port: the infrared port automatically opens and sends the card. Or select Mail or SMS, then enter the mobile number to send the card to or select it via Options then Names list and press OK.