User manual MITSUBISHI WD-52525 - Owners Guide

Projection Television Models WD-52525, WD-52725 WD-62525, WD-62725 Owner's Guide TM TM visit our website at www.mitsubishi-tv.com TV Information: Use this space to record the model and serial numbers of your television. This information is on the back of your TV. Model number Serial number CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user of the presence of uninsulated "dangerous voltage" within the product's enclosure that may be sufficient magnitude to constitute a risk of electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. This TV is very heavy! Exercise extreme care when lifting or moving. A minimum of two adults should lift or move the TV. Portions of the advanced circuitry of this TV must continue to operate even when the TV is turned off. Some of these circuits therefore need to be cooled at all times. A low power standby fan may be heard in a quiet environment. This is normal operation. Custom cabinet installation must allow for proper air circulation around the television. STAND REQUIREMENT CAUTION: Mitsubishi TV models WD-52525 and WD-52725 are for use only with Mitsubishi stand, model MB-52525. Mitsubishi TV models WD-62525 and WD-62725 are for use only with Mitsubishi stand model MB-62525. Use with other stands is capable of resulting in instability causing possible injury. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. NOTE TO CATV SYSTEM INSTALLER: THIS REMINDER IS PROVIDED TO CALL THE CATV SYSTEM INSTALLER'S ATTENTION TO ARTICLE 820-40 OF THE NEC THAT PROVIDES GUIDELINES FOR THE PROPER GROUNDING AND, IN PARTICULAR, SPECIFIES THAT THE CABLE GROUND SHALL BE CONNECTED TO THE GROUNDING SYSTEM OF THE BUILDING, AS CLOSE TO THE POINT OF CABLE ENTRY AS PRACTICAL. FCC Declaration of Conformity Product: Models: Responsible Party: Projection Television Receiver WD-52525, WD-52725, WD-62525, WD-62725 Mitsubishi Digital Electronics America, Inc. 9351 Jeronimo Road Irvine, CA 92618-1904 949-465-6000 Telephone: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · · · · Reorient or relocate the receiving antenna. Increase the separation between the equipment and the receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. CAUTION: To assure continued FCC compliance, the user must use a shielded video interface cable with bonded ferrite cores at both ends, when using the PC or HDMI input. Changes or modifications not expressly approved by Mitsubishi could cause harmful interference and would void the user's authority to operate this equipment. Contents Chapter 1 Television Overview TV Accessories............................................................................................................. 10 Special Features........................................................................................................... 10 Front Control Panel ...................................................................................................... 11 Front Panel Inputs and Media Card Slots .................................................................... 12 Back Panel.................................................................................................................... 13 Chapter 2 Connecting External Devices & NetCommand® Setup .................................................................. 16 Wall Outlet Cable or Cable Box.................................................................................... 17 CableCARDTM Technology ........................................................................................... 18 Single Lead Antenna .................................................................................................... 19 Separate UHF and VHF Antennas ............................................................................... 19 VCR Video and Audio to an Antenna or Wall Outlet Cable .......................................... 20 VCR Video and Audio to a Cable Box .......................................................................... 21 A/V Receiver or Stereo System.................................................................................... 22 Satellite Receiver or Other Device with S-Video .......................................................... 22 DVD Player with Component Video.............................................................................. 23 Computer with a PC Monitor Output............................................................................ 23 DTV Receiver with Component Video.............................................................................................. 24 with RGB, HV Video ................................................................................................. 25 M-Link Control.............................................................................................................. 26 RS-232C Connection ................................................................................................... 26 HDMI Device................................................................................................................. 26 DVI Device .................................................................................................................... 26 IR Emitter NetCommand® ........................................................................................... 27 Compatible IEEE 1394 Devices .................................................................................... 28 Helpful Hints ................................................................................................................. 30 Chapter 3 NetCommand ® Setup and Editing Using the Remote Control with NetCommand®.......................................................... 32 Remote Control Functions: Overview........................................................................... 33 Remote Control Functions: Operation................................................................................................................. 34 Care ......................................................................................................................... 34 Sleep Timer ............................................................................................................. 34 NetCommand® OnScreen Buttons ............................................................................. 35 3D Graphical Viewpoint® Menu System...................................................................... 36 NetCommand® Initial Setup ........................................................................................ 37 Edit NetCommand® Add an A/V Receiver .............................................................................................. 39 Add Devices ........................................................................................................... 42 Change Devices ..................................................................................................... 46 Delete Devices........................................................................................................ 46 Finish Screen.......................................................................................................... 46 Chapter 4 IEEE 1394 Devices and NetCommand® Controlled Recordings IEEE 1394 Devices and NetCommand® Control ......................................................... 48 Adding IEEE 1394 Devices Automatically..................................................................... 49 Device Selection Menu................................................................................................. 51 Using the DEVICE MENU Button to Display Menus........................................................ 52 Using the Guide Button to Display ChannelViewTM and Menus................................... 53 NetCommand® Controlled Recordings ....................................................................... 54 NetCommand® and Traditional VCR's......................................................................... 54 NetCommand® Controlled Peer-to-Peer Connections ............................................... 56 Direct VCR Recording from an Antenna or Cable Screen ........................................... 57 A/V Disc Search ........................................................................................................... 57 Track List Screen ......................................................................................................... 57 PC Viewing ................................................................................................................... 58 MediaCommandTM and Media Card Playback............................................................. 59 Chapter 5 TV Menu Screen Operations Main Menu Choices...................................................................................................... 62 Setup Menu .................................................................................................................. 63 NetCommand® Menu .................................................................................................. 64 Antenna Menu .............................................................................................................. 65 Time Menu.................................................................................................................... 67 Captions Menu ............................................................................................................. 68 V-Chip Lock Menu........................................................................................................ 70 AudioVideo Menu ......................................................................................................... 73 A/V Settings Descriptions ............................................................................................ 74 Operation of PIP and POP............................................................................................ 76 Chapter 6 Special Features Display Formats ........................................................................................................... 78 Device Control with NetCommand®............................................................................ 81 Appendix A: Bypassing the V-Chip Lock ..................................................................... 83 Appendix B: Specifications .......................................................................................... 85 Appendix C: Remote Control Programming Codes..................................................... 87 Appendix D: On-Screen Information Displays ............................................................. 90 Appendix E: NetCommand® Specialized Device Keys .............................................. 91 Appendix F: Cleaning and Service ............................................................................... 92 Appendix G: Diamond ShieldTM Removal .................................................................... 93 Appendix H: Filter Cleaning.......................................................................................... 94 Lamp Replacement ...................................................................................................... 95 Troubleshooting............................................................................................................ 97 Additional Information .................................................................................................. 102 Index ............................................................................................................................. 103 Warranty ....................................................................................................................... 105 IMPORTANT SAFEGUARDS Please read the following safeguards for your TV and retain for future reference. Always follow all warnings and instructions marked on the television. 1. Read, Retain and Follow All Instructions Read all safety and operating instructions before operating the TV. Retain the safety and operating instructions for future reference. Follow all operating and use instructions. 2. Heed Warnings Adhere to all warnings on the appliance and in the operating instructions. 3. Cleaning Unplug the TV from the wall outlet before cleaning. Do not use liquid, abrasive or aerosol cleaners. Cleaners can permanently damage the cabinet and screen. Use a lightly dampened cloth for cleaning. 4. Attachments and Equipment Never add any attachments and/or equipment without approval of the manufacturer as such additions may result in the risk of fire, electric shock or other personal injury. 5. Water and Moisture Do not use the TV where contact with or immersion in water is possible. Do not use near bath tubs, wash bowls, kitchen sinks, laundry tubs, swimming pools, etc. 6. Accessories Do not place the TV on an unstable cart, stand, tripod, or table. The TV may fall, causing serious injury to a child or adult and serious damage to the TV. Use only with a cart, stand, tripod, bracket or table recommended by the manufacturer, or sold with the TV. Any mounting of the TV should follow the manufacturer's instructions, and should use mounting accessories recommended by the manufacturer. An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn. 7. Ventilation Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the TV and to protect it from overheating. Do not block these openings or allow them to be obstructed by placing the TV on a bed, sofa, rug, or other similar surface. Nor should it be placed over a radiator or heat register. If the TV is to be placed in a rack or bookcase, ensure that there is adequate ventilation and that the manufacturer's instructions have been adhered to. 8. Power Source This TV should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supplied to your home, consult your appliance dealer or local power company. 9. Grounding or Polarization This TV is equipped with a polarized alternating current line plug having one blade wider than the other. This plug will fit into the power outlet only one way. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug. 10. Power-Cord Protection Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the TV. 11. Lightning For added protection for this TV during a lightning storm, or when it is left unattended and unused for long period of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the TV due to lightning and power-line surges. 6 IMPORTANT SAFEGUARDS, continued 12. Power Lines An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal. 13. Overloading Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock. 14. Object and Liquid Entry Never push objects of any kind into this TV through openings as they may touch dangerous voltage points or shortout parts that could result in fire or electric shock. Never spill liquid of any kind on or into the TV. 15. Outdoor Antenna Grounding If an outside antenna or cable system is connected to the TV, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electric Code, ANSI/NFPA No. 70-2002, provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. 16. Servicing Do not attempt to service this TV yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel. 17. Damage Requiring Service Unplug the TV from the wall outlet and refer servicing to qualified service personnel under the following conditions: (a) When the power-supply cord or plug is damaged. (b) If liquid has been spilled, or objects have fallen into the TV. (c) If the TV has been exposed to rain or water. (d) If the TV does not operate normally by following the operating instructions, adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the TV to its normal operation. (e) If the TV has been dropped or the cabinet has been damaged. (f) When the TV exhibits a distinct change in performance - this indicates a need for service. 18. Replacement Parts When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock or other hazards. 19. Safety Check Upon completion of any service or repair to the TV, ask the service technician to perform safety checks to determine that the TV is in safe operating condition. 20. Heat The product should be situated away from heat sources such as radiators, heat registers, stoves or other products (including amplifiers) that produce heat. 7 Our Thanks... Thank you for choosing Mitsubishi as your premier Home Entertainment provider. This Owner's Guide describes the features and functions of your Mitsubishi widescreen, high definition TV. We urge you to examine this Owner's Guide to become familiar with the innovative features and operations this unique television offers. The very core of our corporate philosophy is to provide our customers with the very best. Our development team at Mitsubishi has worked to provide you with a television that defines "state-of-the-art," with the capability to meet your needs now and in the future. Whether this is your first Mitsubishi electronic product, or an addition to your Mitsubishi collection, we believe you and your family will continue to enjoy your Mitsubishi home theater for many years. Thank you, Mitsubishi Digital Electronics America, Inc. 8 Chapter . . . 1 Television Overview TV Accessories ..........................................................................10 Special Features ........................................................................10 Front Control Panel.................................................................... 11 Front Panel Inputs and Media Card Slots ...............................12 Back Panel .................................................................................13 TV Accessories Please take a moment to review the following list of items to ensure that you have received everything including: SUB/CANCEL Special Features Your new High Definition widescreen television has many special features that make it the perfect center of your home entertainment system, including: Your widescreen Mitsubishi HDTV uses Texas Instruments Digital Light ProcessingTM technology. This TV is truly a high performance multimedia monitor uniquely capable of both stunning high definition video images and clear detailed high resolution PC images. Your TV is able to accept video signals in the standard video scanning rates of 480i, 480p, 720p and 1080i. It is also able to accept signals with PC resolutions from VGA (640 x 480) through XGA (1024 x 768). When using a compatible graphics card and controlling software, this TV is also able to accept the custom PC resolution of 720p (1280 x 720). All signals will be converted to 720p for final display. High Definition DLPTM Display System CONNECT POWER MUTE GUIDE VIDEO SLEEP CABLE/DBS/DTV VCR DVD AUDIO TV FORMAT AUDIO QV VOL 3 EXCH 6 9 PAUSE FF/FWD HOME PIP DEVICE PIP/POP INFO 2 5 8 0 CH REC TV MENU DEVICE MENU V-CHIP 1. Remote Control 2. Two AA Batteries SQV DEVICE 1 4 7 PIP CH REW/REV STOP PLAY 3. One Digital Audio Cable (sends the audio of digital channels to a digital audio video receiver). Your widescreen Mitsubishi HDTV is "Plug-andPlay" ready. It can descramble a cable provider's one-way digital signals with the use of a CableCARD security module. The CableCARD is used in place of a traditional cable box to access digital cable programming (including high definition). Contact your local cable provider for availability information and service details. Digital Cable Ready (CableCARDTM) 4. One Quadruple IR Emitter Cable (allows NetCommand to control other devices) Your widescreen Mitsubishi HDTV offers a new level of networking to combine selected older products with new and future digital products. NetCommand supports IEEE 1394 connections, Audio Video Control system (AV/C), 5C copy protection and IR control of selected older products such as VCRs, DVD players, cable boxes or satellite receivers. NetCommand includes the ability to learn remote control signals directly from many devices, allowing you to customize the NetCommand system in a way that works best for your viewing. NetCommand® Home Network Control System 16:9 Widescreen Picture Format 5. One Double IR Emitter Cable (allows NetCommand to control other devices) 6. Product Registration Card (not pictured) 7. Owner's Guide (not pictured) 8. Quick Reference Card (not pictured) Enjoy a full theatrical experience in the comfort of your home. View pictures as film directors intended them. Digital TV broadcasts, DVDs and newer video game consoles support this widescreen format. You can display a slideshow of your favorite JPEG pictures or listen to MP3 or WMA audio selections that have been recorded on compatible media cards. Media Cards 10 Front Control Panel The buttons on the Front Control Panel highlighted in gray are duplicated on the remote control. The top row of labels show the control functions when there are no TV menus displayed on the screen. The bottom row of labels show the control functions when the TV menus are displayed on the screen or when a special function has been activated. See Remote Control Overview, for further details on the functions of these buttons. If the TV will not respond to either the remote control or the front panel controls and/or will not power Off, press the SYSTEM RESET button with a pointed item like the end point of a paperclip. The TV will turn Off and the TIMER light will flash quickly for about one minute. When the TIMER light stops flashing, you may again turn on the TV. The changes you made the last time the TV was on before you used the SYSTEM RESET button may be lost, however, the changes that were previously saved are not lost. >> << SYSTEM RESET System Reset POWER LAMP STATUS TIMER < ADJUST < > ­ VOL ­ ­ CH ­ > FORMAT ENTER MENU MENU GUIDE CANCEL DEVICE Indicators COLOR None (off) Green (steady light) Please refer to the table below for conditions when the indicator lights will display. LAMP LIGHT INDICATOR Power off n/a n/a TIMER/ POWER Power off Power on Starting up* TV Timer is set COLOR None (off) Green (steady light) Green ( fast blinking light) Green (blinking light) STATUS LIGHT INDICATOR Power off n/a n/a Green ( fast blinking light) Green (blinking light) Power just turned off, TV cooling down (1 minute). Cannot turn the TV back on until blinking stops. Lamp life end warning. A new lamp should be purchased. See Appendix H. n/a Yellow (steady light) n/a Yellow (steady light) Operating temperature is too high. The dust filter may be dirty. See Appendix H. or The room temperature too hot. Turn off TV until the room is cooler. The filter cover is open or not secure. See Appendix H. Yellow (blinking light) Lamp cover door is open or no lamp installed. See Appendix H. Lamp has failed, replacement is required. See Appendix H. n/a n/a Yellow (blinking light) Red (steady light) n/a Red (steady light) Service required. Turn off TV and call your dealer or a Mitsubishi Authorized Service Center. See www.mitsubishi.com or call 1-800332-2119. Service required. Turn off TV and call your dealer or a Mitsubishi Authorized Service Center. See www.mitsubishi.com or call 1-800332-2119. Red (blinking light) n/a Red (blinking light) *Each time the TV is plugged into a wall electrical outlet, when power is restored after a power failure, or when using the SYSTEM RESET button, this light will flash for about one (1) minute. There may be times when you wish to reset the A/V (Audio and Video) settings back to the factory defaults. To return all of the settings at once, press GUIDE and FORMAT on the front panel at the same time. To reset the defaults for individual devices, use the A/V Memory Reset selection on the AudioVideo menu. A/V Reset 11 Front Panel Inputs and Media Card Slots Media Card Slots and IEEE 1394 Input/Output There are four card slots in the front of the TV that allow the display of JPEG pictures from many digital cameras, MP3 or WMA audio files recorded from computers or other digital recording devices. The card slots are designed for specific types of cards and other cards or objects should not be inserted into the slots as this may damage the TV. CARD1 slot is compatible with both MultiMediaCardTM (MMC) and Secure Digital (SD) cards. CARD-2 slot is compatible with SmartMediaTM cards. CARD-3 slot is compatible with CompactFlash® cards and CARD-4 is compatible with MEMORY STICKTM cards. See media card (slideshow, playlist) Setup for details about JPEG, MP3 and WMA file types that are compatible with the TV. The IEEE 1394 input/output allows for temporary connection of IEEE 1394 devices such as some camcorders, to the front of the TV. This connection works the same way as rear IEEE 1394 connections, please refer to the NetCommand® information (Chapter 3) for details. Input 3 This input can be used for convenient connection of a camcorder or other video device to the TV. Please note that if you connect to the S-VIDEO terminal, the VIDEO terminal is deactivated. The VIDEO terminal is active when there is no S-Video connection. INPUT 3 IMPORTANT Portions of the advanced circuitry of this TV must continue to operate even when the TV is turned off. Some of these circuits therefore need to be cooled at all times. A low power standby fan may be heard in a quiet environment. This is normal operation. 12 Back Panel 7. 6. IEEE1394 INPUT/OUTPUT 8. IR EMITTER NetCommand R PC VGA/SVGA/XGA/ 720p 60 Hz AUDIO R L(MONO) VIDEO S-VIDEO MONITOR OUTPUT 9. L DVI Analog Audio L AUDIO 2 R ANT-2 AUX DTV/ CABLE/ VHF/ UHF R PCAUDIO AUDIO/VIDEO 1 5. 10. INPUT-1 1. 11. HDMI M-LINK ANT-1 MAIN PCINPUT INPUT-2 YPbPr (480i/480p/720p/1080i) COMPONENT-1 M-LINK CONTROL/ RS-232C 4. DIGITAL AUDIO YPbPr (480i/480p/720p/1080i) COMPONENT-2 YPbPr / RGB HV (480i/480p/720p/1080i) INPUT-DTV 12. 2. 3. 1. Antenna (ANT-1 MAIN, ANT-2 AUX) ANT-1 MAIN and ANT-2 AUX can each receive both digital and analog over-the-air channels from a VHF/UHF antenna or non-scrambled digital/analog cable channels. Your primary viewing signal source should be connected to ANT-1 MAIN. ANT-1 MAIN must be used to view premium subscription cable TV service authorized by the CableCARDTM access card. The CableCARD access card is provided by your local cable company. ANT-2 AUX can continue to receive over-the-air or non-scrambled cable signals. CableCARD SLOT CARD TOP Pr/R Pb/B Y/G TM V H This input is used to connect an external DTV receiver, and can be configured for YPbPr or RGB plus H&V signal types. Please see Appendix B for signal compatibility. 3. Input DTV (480i/480p/720p/1080i) These inputs can be used for the connection of devices with component video outputs, such as a DVD player, external HDTV receiver or compatible video game system. Please see Appendix B for signal compatibility. 4. Component-1, -2 Inputs YPbPr (480i/480p/720p/1080i) The CableCARD access card provided by your cable TV service provider is inserted into this slot. The top of the card should face in the direction the CARD TOP arrow indicates. CableCARD is a nationwide standard system that allows your local cable TV provider to supply you with an access card customized to your account. This card allows the TV to receive, decode and unscramble the premium digital channels included in your cable TV subscription without the use of a cable box. See page 16 for additional CableCARD information and activation instructions. If your cable company is not currently offering CableCARD access cards, you will need to use a cable box provided and authorized by your local cable company to view scrambled channels. 2. CableCARDTM Slot 5. Input-1, -2; Monitor Output Input 1 and 2 can be used for the connection of a VCR, Super VHS (S-VHS) VCR, DVD player, standard satellite receiver or other A/V device to the TV. Please note that if S-VIDEO and VIDEO are available for the input, you must choose to connect only one. They cannot both be connected at the same time. The Monitor Output sends the TV audio and video signals from the antennas or Inputs to an A/V receiver or other analog A/V equipment such as a VCR. Digital channels and IEEE 1394 signals will be down converted to analog signals compatible with traditional VCRs. Digital channels or IEEE 1394 signals may be output with copy protection or may display no video signals if they have copy restrictions. There will be only audio and no video signals from Monitor Outputs when viewing the Component 1 & 2 inputs, INPUT-DTV, the HDMI input or Cards 1-4. (Audio/Video 1, Audio 2) 13 Back Panel, continued Monitor Output Audio/Video 1 should be connected to a VCR for recording. Monitor Output Audio 2 should be connected to your A/V receiver for home theater surround sound. 6. PC Input and Audio This input can be used for the connection of a computer. Please see Appendix B for signal compatibility. If NetCommand® has not been setup, the on-screen display name will be VGA. Stereo audio inputs are also provided for the PC connection. Use this input to connect to EIA/CEA-861 compliant devices such as a high definition receiver or DVD player. This input supports 480i, 480p, 720p and 1080i video formats. It is not intended for use with personal computers or devices outputting video signals with computer resolutions. This input can also be used as a DVI connection with separate analog audio inputs. An optional HDMI-toDVI adaptor or cable will be necessary to make this connection and may be available from your local electronics retailer. When using the optional HDMI-toDVI adapter, the DVI analog audio inputs on your TV allow you to receive left and right audio from your DVI device. This input is HDCP (High-Bandwidth Digital Copy Protection) compliant. (VGA/WVGA/SVGA/WSVGA/XGA/ 720p, 60Hz ) 7. DTV Link/IEEE1394 These jacks allow the TV to connect to external IEEE 1394 digital products by means of a single cable. Three jacks (one on the front panel and two on the back) are provided for this purpose, which allow for a high degree of flexibility for connecting your NetCommand controlled system. Detailed information regarding IEEE 1394 connection requirements are in Chapter 4. 11. M-Link/RS-232C Control A digital control interface that works in conjunction with M-Link. While M-Link provides the digital video signal, the RS-232 control provides enhanced functioning such as automatic power ON/OFF and input port selection with an external control system. For RS-232 command protocol please visit www.mitsubishi-tv.com. Two jacks are provided for connecting IR emitters. IR Emitters connected to these jacks are used by the NetCommand system of the TV to control external analog devices such as VCRs, DVDs, cable boxes, satellite receivers and audio receivers. 8. IR Emitter-NetCommand® 12. Digital Audio Output Unlike HDMI, DVI does not carry audio information on the same cable. Use these analog stereo audio inputs when using the HDMI input with a device that outputs DVI instead of HDMI. 9. DVI Analog Audio This output will automatically send Dolby® Digital audio from digital channels and IEEE 1394 devices to a digital Audio/Video receiver. Connect this output to the A/V receiver's coaxial digital audio input. The output will automatically turn off when viewing an analog channel or device. Use Monitor Output Audio 2 to send analog sound to your A/V receiver. Some digital cable channels send MPEG-1 digital audio instead of Dolby Digital, however, not all A/V receivers can decode MPEG-1 digital audio. This can cause the A/V receivers to produce a loud noise that can damage speakers. For this reason, the TV will automatically turn off the digital audio output when tuned to a channel or device that has MPEG-1 digital audio and send it to the A/V receiver as analog left and right audio from Monitor Output. 10. HDMI/M-Link M-Link(MonitorLinkTM) is a Mitsubishi exclusive proprietary digital interface for the display of high quality digital video signals from Mitsubishi products, such as the HD-6000 HDTV Receiver/Controller. The HDMITM (High Definition Multimedia Interface) supports uncompressed standard and high definition digital video formats and existing digital multi-channel audio formats. If using a cable box, the HDMI input supports both video and audio using a single cable. 14 Chapter . . . 2 Connecting External Devices & NetCommand® Setup..................................16 Wall Outlet Cable or Cable Box ....................................................17 CableCARDTM Technology.............................................................18 Single Lead Antenna......................................................................19 Separate UHF and VHF Antennas ...............................................19 VCR Video and Audio to an Antenna or Wall Outlet Cable ........20 VCR Video and Audio to a Cable Box ..........................................21 A/V Receiver or Stereo System....................................................22 Satellite Receiver or Other Device with S-Video ........................22 DVD Player with Component Video..............................................23 Computer with a PC Monitor Output ...........................................23 DTV Receiver with Component Video ...............................................................24 with RGB, HV Video ...................................................................25 M-Link Control, RS-232 Connection............................................26 HDMI Device...................................................................................26 DVI Device.......................................................................................26 IR Emitter NetCommand® ............................................................27 Compatible IEEE 1394 Devices.....................................................28 Helpful Hints ...................................................................................30 Connecting External Devices & NetCommand® Setup NetCommand is able to control many current audio and video devices by sending remote control signals from the TV to each device through IR emitters. Additionally, it is also able to learn the remote control signals used by most audio video devices not already in the TV's memory. NetCommand can automatically switch the TV and compatible or learned Audio/Video (A/V) Receivers to the correct input used with each device. It is important that the inputs on the TV and A/V receiver back panels match the NetCommand setup that is displayed on-screen. To simplify the installation of NetCommand, there is a step-by-step on-screen NetCommand Setup procedure in this chapter, which details the type and brands of devices you are connecting to the TV. The NetCommand Setup also assigns preset TV and A/V receiver inputs for each device. You should connect each device to the TV input (both audio and video) and to the A/V receiver (audio) as shown in the figure below. video and stereo audio cables Device to be connected stereo and/or digital audio cables IR Emitters TV stereo and digital audio cables AV Receiver The following charts show which preset inputs you should use on the TV and A/V receiver. Chart 1 shows TV inputs. Chart 2 shows the A/V receiver inputs used by A/V receiver models already known by NetCommand. Chart 1 Device Audio and Video Outputs to TV Inputs Cable for CableCARDTM Service Antenna/Cable (digital/analog) Cable box VCR Satellite Receiver (DBS) Camcorder DVD Player ANT-1 ANT-1 if primary viewing source, ANT-2 if secondary viewing source ANT-2 Input-1 Input-2 Input-3 (on front panel) Component-1 Mitsubishi 1 Mitsubishi 2 Bose Model Model Model M-VR800 & M-VR900 & Lifestyle ®28 M-VR1000 M-VR700 Denon Model AVR-2700 Integra Kenwood Marantz Pioneer 1 Pioneer 2 Model Model Model Model Model DTR-9.1 VR-2080 SR8200 VSX-D557 VSX-49TX Rotel Sony Yamaha 1 Yamaha 2 Model Model Model Model RSX-1065 STR-DE825 RV-X2095 RX-V2200 Chart 2 Device Audio Output to VCR VCR 1 Satellite Receiver Aux DVD Player DVD TV Monitor Output TV (& Digital Audio) AV Receiver Inputs by Name VCR VCR VCR-1 Cable/DBS AUX CD DVD (built-in) DVDVDP TV TV TV/DBS Video 1 Video 3 DVD Video 4 Video 1 Video 3 Video 4 Video 4 VCR1 DSS DVD TV VCR/Tape VCR 1/DVR CD SAT LD/SAT DVD/LD DVD/TV TV Video 2 Video 4 Video 5 Video 1 Video 1 TV/DBS TAPE/MD DVD/LD VCR 1 TV/DBS CD DVD/LD VCR 1 D-TV/LD DVD CBL/SAT After using NetCommand Setup, you may go to the NetCommand menu at any time to change the inputs you used for connecting each device, custom name devices, add devices not included in the presets above or delete devices no longer used. See Edit NetCommand. See Helpful Hints, at the end of this chapter for additional information on device setup. 16 Connecting a Wall Outlet Cable or Cable Box Wall Outlet Cable (can be used with a CableCARDTM) Figure 1 It is very important to connect the incoming cable for your primary viewing source to ANT-1, especially for CableCARDTM use. 1. Connect the primary incoming coaxial lead cable to ANT-1 MAIN on the TV back panel. 2. For an optional secondary antenna source, connect an antenna (or cable) to ANT-2 AUX. 3. If you have subscribed to a CableCARDTM service, the CableCARD can now be inserted into the CableCARD SLOT. Using a phillips screwdriver, remove the CableCARD cover screws. Insert the CableCARD, then replace the cover and screws. Additional CableCARD information is on page 18. TV back panel section 2. Optional Secondary Antenna or Cable IR EMITTER NetCommand R Figure 2 3 coaxial cables and one two-way RF splitter are required. These are not included with the TV. Cable Box (compatible with PIP/POP) It is very important to connect the incoming cable for your primary viewing source to ANT-1, especially for CableCARDTM use. 1. Connect the incoming cable to IN on an RF splitter. 2. Connect one coaxial cable from OUT on the RF splitter to ANT-1 MAIN on the TV back panel. 3. Connect one coaxial cable from OUT on the RF splitter to IN on the cable box. 4. Connect one coaxial cable from OUT on the cable box to ANT-2 AUX on the TV back panel. Cable Box back panel section 3. IN TV back panel section IR EMITTER NetCommand R OUT L DVI Analog Audio 4. 3. 4. L DVI Analog Audio R ANT-2 AUX DTV/ CABLE/ VHF/ UHF HDMI M-LINK ANT-1 MAIN R ANT-2 AUX DTV/ CABLE/ VHF/ UHF HDMI M-LINK ANT-1 MAIN TWO WAY SPLITTER OUT 1. IN 2. M-LINK CONTROL/ RS-232C Incoming Cable OUT 2. 1. Primary Wall Outlet Cable M-LINK CONTROL/ RS-232C DIGITAL AUDIO Figure 2. Connecting a Cable Box CableCARD SLOT CableCARD SLOT (cover removed) TM 3. CARD TOP TM Figure 1. Wall Outlet Cable Note: Net Command® will assume that your Cable Box is connected as shown above. Also, that Channel 3 is the default output channel for the cable box. If either the connections or output channel are different, use the Change option of Edit NetCommand to apply the changes. IMPORTANT Additional connection cables are not provided with the TV. They are available at most electronic stores. 17 CableCARDTM Technology CableCARD Technology CableCARD is a nationwide system standard that allows your local cable TV provider to supply you with an access card customized to your account. This card allows your TV to receive, decode and unscramble the premium digital channels included in your cable TV subscription, without the use of a cable box. It also allows your cable provider to automatically update and change your subscription. When you move to a new cable provider's area, you simply return the CableCARD to the original cable provider and get a new card from your new cable provider. Please note that CableCARD is a new technology and your local cable provider may not currently be offering this service. As time passes, this system will become broadly supported by most cable providers. The CableCARD system is "unidirectional" which means your cable provider can send updates to the access card and TV, however, the TV cannot send back signals such as requests for Video-On-Demand or Pay-per-View request by remote control. Digital cable channels authorized by the CableCARD will be available on the Firewire® IEEE 1394 network and can be shared by other products on the network. Some digital channels or programs may not be copied or recorded because of copy restriction limits set by the content owners or copyright holders. The digital television is cable of receiving analog basic, digital basic and digital premium cable television programming by direct connection to a cable system providing such programming. A security card (CableCARD) provided by your cable operator is required to view encrypted digital programming. Certain advanced and interactive digital cable services such as video-on-demand, a cable operator's enhanced program guide and dataenhanced television services may require the use of a set-top box. For more information call your local cable operator. Please see page 17 for instructions on how to insert the CableCARD. Using a CableCARD After inserting a CableCARD into the TV back panel CableCARD slot and powering On the TV, the initialization process begins. An initial screen will automatically display for a few minutes, with information that your Cable Provider will need in order to start service. Please write down this information before calling your cable provider. Please call XYZ Cable at xxx-xxx-xxxx to activate cable service. They will need these numbers: Host ID X-XXX-XXX-XXX-XXX CableCARDTM ID: X-XXX-XXX-XXX-XXX See owner's manual for further information An example of an initial screen is shown here. Your screen will display specific information from your cable provider and may not look like this screen. If you were unable to record the information, you can press TV MENU on the remote and then enter the number 999 and the screen will re-display. You can also press DEVICE MENU when the CableCARD is the selected source and you will be able to select the startup application. IMPORTANT To use a CableCARD, the primary incoming cable must be connected to ANT-1 MAIN. 18 Connecting a Lead Antenna or Separate UHF and VHF Antenna Lead Antenna (not for use with CableCARDTM) Figure 3 A 300-Ohm to 75-Ohm transformer is required. This is not included with the TV, but is available at most electronics stores. Figure 4 A UHF/VHF combiner is required. This is not included with the TV. Separate UHF and VHF Antenna For antennas with twin flat lead 1. For antenna with twin flat leads, connect the 300-Ohm twin leads to the 300-Ohm to 75-Ohm transformer. 2. Push the 75-Ohm side of the transformer onto ANT-1 MAIN on the TV back panel. For cable or antenna with coaxial lead 3. Connect the coaxial lead directly to ANT-1 MAIN on the TV back panel. 1. Connect the UHF and VHF antenna leads to the UHF/VHF combiner. 2. Push the combiner onto ANT-1 MAIN on the TV back panel. VHF Antenna (Channels 2-13) UHF Antenna (Channels 14-69) Flat Twin Lead External Antenna or Cable Flat Twin Lead TV back panel section IR EMITTER NetCommand R TV back panel section IR EMITTER NetCommand R L DVI Analog Audio R 300 Ohm to 75 Ohm Combiner UHF ANT-2 AUX DTV/ CABLE/ VHF/ UHF 2. Side HDMI M-LINK ANT-1 MAIN 300-Ohm FlatTwin Lead 75-Ohm Coaxial Cable DVI L Analog Audio R VHF M-LINK CONTROL/ RS-232C Back ANT-2 AUX DTV/ CABLE/ VHF/ UHF 3. HDMI M-LINK 1. ANT-1 MAIN Figure 4. Connecting separate UHF and VHF Antennas 2. Optional 300-Ohm to 75-Ohm Matching Transformer 1. M-LINK CONTROL/ RS-232C Figure 3. Connecting a Single Antenna Mitsubishi strongly recommends against using antennas with twin flat leads. Twin flat lead antenna wires are subject to interference which may adversely affect the performance of the TV. We recommend using coaxial antenna cable. 19 Connecting VCR Video and Audio to an Antenna or Wall Outlet Cable VCR Video and Audio to an Antenna or Wall Outlet Cable Figure 5 A two-way RF splitter, 3 coaxial cables, right and left audio cables and a S-Video or Video cables are required. These are not included with the TV. 1. Connect the incoming cable or Antenna to IN on the RF splitter. 2. Connect one coaxial cable from OUT on the RF splitter to ANTENNA IN on the VCR back panel. 3. Connect one coaxial cable from OUT on the RF splitter to ANT-1 MAIN on the TV back panel. 4. To use the TV speakers with the VCR, connect a set of audio cables from AUDIO OUT on the VCR back panel to INPUT-1 AUDIO-LEFT (MONO) and AUDIO-RIGHT on the TV back panel. The red cable connects to the R (right) channel and the white cable connects to the L (left) channel. If your VCR is mono (non-stereo), connect only the white (left) cable. 5. Connect either an S-Video or Video cable from VIDEO OUT on the VCR back panel to INPUT-1 VIDEO on the TV back panel. Only one type of video cable should be connected. S-Video is recommended, if available. 6. For NetCommand® controlled recordings, connect a set of audio cables from AUDIO IN on the VCR back panel to MONITOR OUTPUT AUDIO/VIDEO 1 AUDIO-LEFT (MONO) and AUDIO-RIGHT on the TV back panel. The red cable connects to the R (right) channel and the white cable connects to the L (left) channel. 7. Complete the NetCommand controlled recordings connections by connecting a Video cable from VIDEO IN on the VCR back panel to MONITOR OUTPUT AUDIO/VIDEO 1 on the TV back panel. 6. TV back panel section