Maintenance Jet Cleaning Your iron has a built in cleaning system designed to keep the water valve, steam chamber and steam vents clear of lint and loose mineral deposits. The `jet clean' should be operated after each period of ironing. To operate, ensure that there is little water in the tank, place the iron on its heel and turn the temperature control dial to the maximum setting. Wait for the temperature indicator light to go out, then unplug the iron and hold it 6'' (150mm) above the sink in the ironing position. Push in the steam control about 10 times in succession. After this cleaning operation, empty out any remaining water. To clean a coated soleplate In the unlikely event of any manmade fibre fusing to the soleplate, set the iron at the 3 dot position and pass it over a clean piece of cotton which will draw the deposit off the surface. Do not use scouring powder or solution as this could cause damage to the coating. To clean the exterior Allow the iron to cool and wipe over with a damp cloth and mild detergent, then dry with a dry cloth. Voyager travel iron Includes World Wide Travel Adaptor World Wide Travel Adaptor The world wide travel adaptor converts UK plugs to foreign sockets in seconds. Morphy Richards products are intended for household use only. Morphy Richards has a policy of continuous improvement in product quality and design. The Company, therefore, reserves the right to change the specification of its models at any time. The adaptor consists of both a continental adaptor plug for travel within Europe and a trans-continental adaptor plug for use in North/South America, Japan, Far East and Australia. Attention It is not suitable for use in all countries. Morphy Richards Limited, Mexborough, South Yorkshire, England, S64 8AJ 441/3752/21 Rev 1 The After Sales Division, Morphy Richards Ltd, Mexborough, South Yorkshire, England, S64 8AJ Helpline (office hours) :UK (local rate) 08450 777700, Republic of Ireland 1800 409119 Two year guarantee This guarantee is valid in the UK and Ireland only. It is in your interest to retain the retailers receipt as proof of purchase. Please quote the following information if the product develops a fault. These numbers can be found on the base of the product. Model No. Serial No. guarantee the appliance must have been used according to the manufacturers instructions. For example kettles should have been regularly descaled or an iron cord should have been stored as recommended by the instructions. EXCLUSIONS Morphy Richards shall not be liable to replace or repair the goods under the terms of the Guarantee where: 1 The fault has been caused or is attributable to accidental use, misuse, negligent use or used contrary to the manufacturers recommendations or where the fault has been caused by power surges or damage caused in transit. 2 The appliance has been used on a voltage supply other than that stamped on the products. 3 Repairs have been attempted by persons other than our service staff (or authorised dealer). 4 Where the appliance has been used for hire purposes or nondomestic use. 5 Morphy Richards are not liable to carry out any type of servicing work, under the guarantee. 6 Plastic filters for all Morphy Richards kettles and coffee makers are not covered by the guarantee. This guarantee does not confer any rights other than those expressly set out above and does not cover any claims for consequential loss or damage. This guarantee is offered as an additional benefit and does not affect your statutory rights as a consumer. Shot of steam to Push in the steam control obtain a boost of extra steam for ironing out creases in heavy material such as denim etc. The shot of steam can be used whilst dry ironing, providing there is water in the tank, and the temperature control is set to the steam position. Do not use shot of steam at temperatures below the steam position shown on the control. Note : For optimum steam quality, do not operate the shot more than three times in succession. Vertical steam Hold the iron in a vertical position between 1 cm and 2 cm away from , the item. Push the steam control this will create vertical steam. This feature is especially useful for removing creases from hanging clothes, curtains, wall hangings, etc. Slide the beaker in between the handle and the main body of the iron . All Morphy Richards products are individually tested before leaving the factory. In the unlikely event of any appliance proving to be faulty within 28 days of purchase it should be returned to the place of purchase for it to be replaced. If the fault develops after 28 days and within 24 months of original purchase, you should contact the Helpline number quoting Model number and Serial number on the product, or write to the address on the front page. You will be asked to return the product (in secure, adequate packaging) to the address on the front page along with a copy of proof of purchase. Subject to the exclusions set out below (see `Exclusions') the faulty appliance will then be repaired or replaced and dispatched usually within 7 working days of receipt. If for any reason this item is replaced during the 2 year guarantee period, the guarantee on the new item will be calculated from original purchase date. Therefore it is vital to retain your original till receipt or invoice to indicate the date of initial purchase. To qualify for the 2 year Ensure the iron is thoroughly dry then place in the bag provided. Important : The flex can be damaged if wound too tightly around the iron after use. Make a loose loop with the flex and wrap it around the iron. The iron must be cool before winding the flex and storing on its heel. Emptying and Storing When you have finished ironing, unplug your iron. Ensure that the is set at the steam control position. Remove the water inlet cover and empty any remaining water out of the filling hole. Replace the water inlet cover. 2 7 Electrical requirements Check that the voltage on the rating plate of your appliance corresponds with your house electricity supply which must be A.C. (Alternating current). If the socket outlets in your home are not suitable for the plug supplied with this appliance the plug should be removed and the appropriate one fitted. IMP0RTANT : THE PLUG REMOVED FROM THE MAINS LEAD, IF SEVERED, MUST BE DESTROYED AS A PLUG WITH A BARED FLEXIBLE CORD IS HAZARDOUS IF ENGAGED INTO A LIVE SOCKET OUTLET. Should the fuse in the 13 amp plug require replacement, a 13 amp BS1362 fuse must be fitted. WARNING : THIS APPLIANCE MUST BE EARTHED. Components of your iron Textiles and clothes are supposed to carry ironing instructions. If they don't you should follow the fabric guide on page 4, but be sure to test the temperature by ironing the hem of the garment or similar area first. If you turn the control dial down from a hot setting to a cooler setting, wait until the iron temperature has stabilised before you continue ironing. Filling 1 Temperature control dial Temperature indicator light Sole plate Water tank Water inlet cover Steam control 2 Before filling the iron with water, ensure that the iron is unplugged is set to and the steam control . Pull the water inlet cover out and pour the water through the , filling hole into the water tank . In using the beaker provided hard water areas the use of distilled or demineralised water is recommended. Replace the water inlet cover before using the iron. Never use battery topping-up fluid or water containing any substances like starch or sugar, or defrosted water from a refrigerator. Instructions for use Temperature guide Heat setting markings on the adjustable control dial of all Morphy Richards irons match those of the international Textile Care Labelling Code. Symbol (120 C Max) Cool (160 C Max) Warm (210 C Max) Hot Control knob positions Fabric Do not iron at all Nylon, Acetates e.g. Acrilan Courtelle, Orlon Triacetates, e.g. Tricel/Polyester Iron on wrong side. If moisture required use damp cloth (Not Acetate) Wool, polyester mixtures e.g. Polyester/Cotton Cotton, linen Rayon, Rayon mixtures, e.g. Rayon/Linen Fabrics requiring this setting usually require steam pressing for heavy cotton, denim etc o o o Dial pointer Before use It is recommended that you use up one beaker of water by operating your iron's steam and shot of steam functions before ironing any clothes as some dripping may occur while your iron's steam system is first activated. Note : The steam facility should only be used on garments which are suitable for ironing at the 3 dot setting. 3 Ironing With water in tank Dry Steam /shot of steam Dry ironing Without water in tank 4 5 4 Always pour out the remaining water after use. Dry ironing You can also use your iron as a dry iron only. Make sure the steam is set to the symbol. control Any temperature setting may be used depending on the garment. You do not need to put any water in the tank when dry ironing only. Steam control Important safeguards WARNING : When filling your iron with tap water always use the beaker provided. Never fill directly under the tap. Temperature control Plug in the iron and switch on. Set the temperature control dial to the temperature required, but don't start ironing immediately. If you wait a few minutes, the iron will stabilise at the required setting. It is always a good idea to begin with `cool' fabrics and work up to higher settings. An iron heats up quicker than it cools down so you'll save time and electricity. Fill the iron with water as described in "Filling", (page 5) and insert the plug into the electrical socket. Turn the temperature control dial , to the "steam" position shown as and rest the iron on it's heel whilst it warms up. Turn the steam control to the . steam position. The steam facility should only be used on garments which are suitable for ironing at the 3 dot setting. Features of your iron Temperature indicator light shows that The indicator light the iron is warming up. When the required temperature is reached the light will go out and will cycle on-off during operation. This shows that the iron is maintaining the heat setting you have chosen. 11 Do not leave the iron unattended whilst plugged in or on an ironing board. Never allow the mains lead to When using your iron, basic safety over hang the work surface. precautions should always be followed, 12 Burns can occur from touching including the following: hot metal parts, hot water or steam. Use caution when you turn a steam 1 Read all the instructions. iron upside down, there may be hot 2 Use the iron only for its intended water in the water tank. use. 3 To protect against the risk of Special instructions electric shock do not put the appliance in water or in any other 1 If your iron does not work, check liquid. the following points: Has the 4 Close supervision is necessary temperature control been set to the when any appliance is used near required temperature? Is the plug in children. NEVER ALLOW A CHILD its socket? Is the plug itself or the TO USE THIS PRODUCT. socket faulty?(Check by plugging in 5 The socket should always be off another appliance). before plugging or unplugging from the socket. Never yank the cord to 2 Warning : When not in use, your iron should never be placed flat disconnect from socket, instead, and left on an ironing board. grasp plug and pull to disconnect. 3 To prevent damage to the textile 6 Do not allow cord to touch hot being ironed, follow the tempera surfaces. Let iron cool completely ture guide carefully. (Test on the before putting away. Loop cord inside hem of the garment). loosely around the iron before 4 When ironing is complete, remove storing. the plug from the socket, empty 7 Always disconnect the iron from any remaining water from the tank, the electrical socket when filling and allow to cool before storage. with water or emptying and when 5 If you drop or severely knock not in use. your iron this could cause internal 8 Do not use outdoors. damage even if the outside appears 9 Do not operate the iron if it has a alright. Have it checked by a damaged cord or if the iron itself qualified electrician. has been dropped or damaged. To avoid the risk of electric shock, do not disassemble the iron, but telephone Morphy Richards for advice. Incorrect reassembly can cause a risk of electric shock when the iron is used. 10 Do not use the vertical steam feature on clothes that are being worn. SAVE THESE INSTRUCTIONS 6 3 ...