TM Bluetooth Wireless Hands Free Car Kit User's Guide > Welcome Welcome to Motorola's "connected" world of BluetoothTM personal area wireless networking. The Motorola Bluetooth Wireless Hands Free Car Kit makes wireless connection simple and quick. The advanced, sophisticated Motorola Bluetooth Wireless Hands Free Car Kit offers these features: · seamless, wireless hands-free audio through Bluetooth link · digital audio interface with high quality, full-duplex, hands free speech · Voice Recognition · voice user interface · entertainment mute--automatically mutes radio during calls · noise reduction and acoustic echo cancellation · automatic volume control · Ignition sense--continue an active call after car is turned off · compliance with Bluetooth Headset v1.1 and Bluetooth Hands Free 0.96 profile Note: There may be differences between the performances of the Bluetooth headset profile and the Bluetooth Hands Free profile. See the "Using Your Car Kit" chapter for details. 1 Personal Communications Sector 600 North U.S. Highway 45 Libertyville, Illinois 60048 1-800-331-6456 (United States) 1-888-390-6456 (TTY/TDD United States) 1-800-461-4575 (Canada) www.motorola.com (United States) www.motorola.ca (Canada) MOTOROLA, the Stylized M Logo and all other trademarks indicated as such herein are trademarks of Motorola, Inc. ® Reg. U.S. Pat. & Tm. Off. The Bluetooth trademarks are owned by their proprietor and used by Motorola, Inc. under license. All other product or service names are the property of their respective owners. © 2002 Motorola, Inc. All rights reserved. Printed in the U.S.A. Manual number: 6889176G01-O 2 Contents Welcome . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Safety and General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Installing the Hands Free Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Guidelines for Installation and Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Installation Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Using Your Car Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 The Control Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Linking Your Car Kit and Phone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Disconnecting the Car Kit from Your Phone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Training Your Car Kit's Internal Voice Recognition . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Placing a Call with the Car Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Using Features While on a Call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Training Quick Reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Calling Features Quick Reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Motorola Limited Warranty for Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Total Customer Satisfaction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Motorola's Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 3 Safety and General Information IMPORTANT INFORMATION ON SAFE AND EFFICIENT OPERATION. READ THIS INFORMATION BEFORE USING YOUR PHONE. Users are not permitted to make changes or modify the device in any way. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. See 47 CFR Sec. 15.21. This device complies with part 15 of the FCC rules and with RSS-210 / RSS-139 of the Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. See 47 CFR Sec. 15.19(3). Canada Compliance (Industry Canada) To prevent radio interference to the licensed service, this device is intended to be operated indoors and away from windows to provide maximum shielding. Equipment that is installed outdoors is subject to licensing. European Union (EU) and EFTA This equipment complies with the R&TTE directive 1999/5/EC and has been provided with the CE mark accordingly. Electromagnetic Interference/Compatibility Nearly every electronic device is susceptible to electromagnetic interference (EMI) if inadequately shielded, designed, or otherwise configured for electromagnetic compatibility. 4 Installing the Hands Free Kit Guidelines for Installation and Connection · Only qualified personnel should install this car kit. If necessary, contact with vehicle manufacturer for air bag information specific to the vehicle. Caution: An air bag inflates with great force. DO NOT place objects, including communication equipment, in the area over the air bag or in the air bag deployment area. If the communication equipment is improperly installed and the air bag inflates, serious injury could occur. · Mount components securely on strong surfaces to prevent shifting that could cause injury or interfere with safe vehicle operation. Always use the supplied mounting hardware · Mounted components and attached wires or cables must not interfere with seating or leg space. · Route cables so they are protected from pinching, sharp edges, and crushing. Keep all in-line connectors easily accessible. · This car kit is intended for use in 12 volt negative ground systems only. The car kit draws less than 3 amps. Confirm that the vehicle's electrical system can supply this current. Installing the Hands Free Kit Installation Procedure Caution: This car kit must be connected to a maximum 10A fuse in the car fuse panel to prevent fire or other damages if a short circuit should occur somewhere in the Junction Box. Before installation, unpack, assemble, and test all components on a service bench. Installing the Bluetooth Junction Box Mount the box using the screws provided. The best location for the Bluetooth junction box is under the dash. The box must be protected from dirt and moisture and have adequate space for cooling and to allow for cable connection. For optimal Bluetooth performance, mount the junction box so that the side with the barcode faces away from the mounting surface. 5 The location MUST NOT interfere with the vehicle's air bag deployment. Installing the Power Cable and Fuse Kit Caution: Failure to follow these steps may cause the accessory not to work properly and may cause damage to the car kit. Speaker (SSN4020) Junction Box (SYN8883A, SYN0415A, SYN0416A, SYN0417A Power Cable (SKN4834A) Microphone (SMN4103) Vehicle Radio Installing the Hands Free Kit Orange Blue C B Control Module (SYN9698A) Wire crimps: green to green, red to red, black to black Black Vehicle Chassis Yellow Green: to a point in the fuse box Red: to a point in fuse box that is always active 4 - 10 AMP fuse Fuse Kit (SKN4937A) 1 Remove all fuses and tape them to their respective holders. DO NOT re-insert fuses until you complete and inspect all connections. 2 Connect the fuse kit's GREEN Ignition Sense wire (3 amp fuse) to an ignition-switched location on the fuse block. When the ignition is off, the ignition sense line is low. 3 Connect the power cable's ORANGE Entertainment Mute Wire to the vehicle's entertainment system. Note: This feature is only operational if the car radio and/or phone support this capability. Installation may require an optional relay (not included). 4 Connect the fuse kit's RED positive primary lead (4 amp fuse) to a point in the vehicle's fuse box that is fused at 4 to 10 amp. 5 Connect the fuse kit's BLACK ground wire to the vehicle chassis. 6 Inspect all connections. Note: The Yellow and Blue wires are not used. 7 Re-insert all fuses. Do not replace any fuse with a higher amperage fuse. Installing the Microphone Note: Always use the supplied mounting hardware. 6 1 Attach one of the three supplied mounting clips to the microphone. 2 Select a suitable location, and mount the microphone. · Locate the microphone no more than 16 inches (40 cm) from the driver. · Aim the microphone directly toward the driver. · Do not allow anything (such as a rear-view mirror or sun visor) to block the path between the microphone and the driver. · Mount the microphone firmly so that vibrations do not affect audio quality. 3 Connect the microphone to the Bluetooth Junction Box. Installing the Hands Free Kit Installing the External Speaker Note: Always use the supplied mounting hardware. 1 Mount the speaker to the transmission hump or beneath the dash. Position the speaker so that it does not directly face the microphone. Caution: The location of the external speaker MUST NOT interfere with the vehicle's air bag deployment. 2 Connect the speaker to the Bluetooth Junction Box. 7 Using Your Car Kit The Control Module The control module enables you to set up and use the Bluetooth Hands Free Car Kit. Bluetooth Button Voice Recognition Button Volume-Up Button C B Using Your Car Kit Microphone Mute Button Volume-Down Button Linking Your Car Kit and Phone Before you can use this car kit, you must link it with your phone. You establish a Bluetooth link between your car kit and phone with a paired link. When you set up a paired link, the car kit remembers the phone's ID. Once the car kit and phone are paired, your car kit automatically connects to your phone every time you start your vehicle or power up the car kit. Initial Pairing With the car kit and phone in close proximity: Step 1 Set the car kit to pairing mode: Start your vehicle. or Power up the car kit by pressing the Bluetooth Button E. Result 8 Step 2 If your phone has a Bluetooth Hands Free Profile, press and hold the Bluetooth Button E.* or If your phone has only a Bluetooth Headset Profile, press and hold both the Bluetooth Button E and the Voice Recognition Button.* Result The Bluetooth Button E and the Voice Recognition Button begin to flash (often 3 seconds). The Bluetooth Button E and the Mute Button begin to flash. You now have two minutes to create a wireless connection between the car kit and your phone. To leave pairing mode before timeout, press the Bluetooth Button E until the buttons stop flashing (often 3 seconds). * If you don't know which profile to use, see "Validating Pairing" on page 10. 3 Set phone to scan and connect to this Your phone scans all Bluetooth Hands car kit. Free devices around it. When your phone "finds" the car kit, it displays For Motorola phones: Motorola BT Car-kit. a Press MENU. b Select SETTINGS. c Select CONNECTION. d Select BLUETOOTH LINK. e Select HANDSFREE. f Select SCAN ALL. Note: If your phone is not a Motorola phone, refer to its manual for instructions on how to scan/discover the car kit. 4 Select LINK. 5 Enter Pass Key or Press 0000 or Press OK/Send/Yes key (depends on your phone) Using Your Car Kit Your phone displays Pass Key. The Bluetooth Button E remains lit (indicating that the link between your phone and the car kit has been established), while all other buttons stop flashing. Validating Pairing To verify whether your phone has the Bluetooth headset or Bluetooth Hands Free profile, attempt to pair your phone with the car kit as if the phone has Bluetooth Hands Free profile. 9 If the Bluetooth link cannot be established, or if you are not able to make a call, then pair your phone and the car kit according to the procedure for Bluetooth headset profile. This car kit can be paired with up to three phones at a time. Automatic Connection After initial pairing, every time you start your vehicle, your phone and car kit will automatically be connected (if your phone's relevant settings are not changed and it is in power-on mode). When the wireless connection is established, the Bluetooth Button E remains lit. If your phone is powered off when you start your vehicle, the Bluetooth connection may not be automatically established when you turn on your phone. To manually establish the connection: Step Press the Bluetooth Button E after you turn on the phone. If the connection cannot be established 10 seconds after you press the Bluetooth Button E, press the button again to restart the paging. Result The Bluetooth Button E begins to flash, and the ca ...