User manual MOTOROLA H550 - Quick Start Guide

motorola Bluetooth Handsfree Headset ® BEFORE YOU BEGIN Before using this product, read the Important Safety and Legal Information pamphlet and follow its instructions. Take a moment before you get started to familiarize yourself with your new H550 Headset. Call Button/ Slide Switch Multi-Color Indicator Light Volume Buttons Microphone Speaker (on reverse side) H550 Get connected in 4 quick steps. 1 Charging Port CHARGE Your Headset's Battery 2 START BLUETOOTH FEATURE Your Phone Your phone's Bluetooth feature is off by default. To use your headset, you must turn on the Bluetooth feature in your phone. For most Motorola phones (at the main menu): 1 Press M (Menu) > Settings > Connection > 1 Verify slide switch is in the off position (toward the charging port). Bluetooth Link > Setup. 2 Plug the Motorola charger into the end of the headset. The indicator light turns red when the battery is charging. It may take up to 1 minute for the indicator light to turn on. When the headset's battery is fully charged (about 2 hours), the indicator light turns off. 2 Scroll to Power. 3 Select Change. 4 Scroll to On. 5 Press Select to turn on the Bluetooth feature. The Bluetooth feature remains on until you turn the feature off. Note: These steps are for most Motorola phones. For other phones, see your phone's user's guide. 3 Disconnect the charger. Note: Headset is not functional while charging. Note: For optimal performance, make sure that the headset is off while charging. 3 PAIR Your Headset Motorola, Inc. Consumer Advocacy Office 1307 East Algonquin Road Schaumburg, IL 60196 www.hellomoto.com 1-877-MOTOBLU 1-888-390-6456 (TTY/TDD United States for hearing impaired) Guide Number: 6809504A24-B Before you can use your headset, you must pair (link) it with your phone. Step A - ENSURE HEADSET IS IN PAIRING MODE Power on headset by sliding the Call button towards the microphone to initiate easy pairing. After a few moments, the indicator light will be steadily lit in blue to indicate headset is in pairing mode. Indicator Light (steadily blue for pairing mode) MOTOROLA and the Stylized M Logo are registered in the US Patent & Trademark Office. The use of wireless devices and their accessories may be prohibited or restricted in certain areas. Always obey the laws and regulations on the use of these products. The Bluetooth trademarks are owned by their proprietor and used by Motorola, Inc. under license. All other product or service names are the property of their respective owners. © Motorola, Inc. 2007. If the headset does not enter pairing mode, see TROUBLESHOOTING for help. 3 PAIR CONTINUED Your Phone 4 TEST AND USE Step B - SET YOUR PHONE TO LOOK FOR YOUR HEADSET For most Motorola phones: Your phone and headset are now paired and ready to make and receive calls. To make a call: 1 On your Motorola phone, press M (Menu) > Settings > Connection > Bluetooth Link > Handsfree > Look for Devices. The phone lists Bluetooth devices it finds. 1 Place the headset over your ear. 2 On the phone, dial the number you want to call and press SEND key on your phone. 3 If your phone and headset are successfully paired, you will hear ringing on the headset. After you have successfully paired your phone and headset, you don't need to repeat these steps. For daily use, ensure that your headset is turned ON and that your phone's Bluetooth feature is ON. To save battery power, turn OFF the headset when you don't use it for an extended time by sliding the switch towards the charging plug. your phone. 4 Enter the passkey: 0000 5 Select OK. 2 Select Motorola H550. 3 Select OK or Yes to pair your headset with When your headset successfully pairs and connects with your phone, the indicator light changes from steadily lit to flashing blue. Note: These steps are for most Motorola phones. For other phones, see your phone's user's guide. USING YOUR H550 See Features and Functions Guide on the reverse side for information on using your H550 TROUBLESHOOTING My headset will not enter pairing mode. Make sure that any devices previously paired with the headset are turned off. If the indicator light is not steadily lit in blue, turn off both the other device and headset, wait 10 seconds, then turn headset back on. Wait for the indicator light to become steadily lit in blue, indicating the headset is now in pairing mode. My phone doesn't find my headset. Make sure the indicator light on your headset is on (lit in blue) and steady when your phone is searching for devices (see step 3). My headset worked before but now it's not working. Make sure your phone is on and the Bluetooth feature is turned on in your phone (see step 2). If the Bluetooth feature was turned off or was turned on only temporarily, you may need to restart the Bluetooth feature (see step 2) and pair your phone and headset again (see step 3). Support. If you need more help, contact us at 1-877-MOTOBLU or visit us at www.hellomoto.com/Bluetoothsupport Note: If desired, your headset can be restored to original factory settings. This action will erase all pairing information stored in your headset. Thus, you will need to pair your phone and headset again (see step 3). To restore your headset to original factory settings, press and hold both Volume buttons and the Call button at the same time for 10 seconds. Features and Functions Guide H550 Bluetooth® Handsfree Headset TURNING HEADSET ON AND OFF To turn your headset on, slide the switch toward the microphone. The indicator light is steadily purple for several seconds, then flashes blue (if paired and connected with another device) or is steadily blue (if ready to be paired). To turn your headset off, slide the switch toward the charging plug. The indicator light will turn off. Slide Switch IMPORTANT: Be sure to first follow the Quick Start Guide on the reverse side of this guide to complete initial setup of your H550. Indicator Light EARHOOKS AND YOUR HEADSET Your H550 headset is supplied with multiple earhooks. The earhook is attached onto a hinge pin, and is placed onto your ear when using your headset. To install an earhook on your headset: WEARING THE HEADSET Once you have attached your desired earhook, follow these steps to wear your headset on your ear: 1 Open the attached earhook 90 degrees from the headset. 1 Open the attached earhook 45 degrees from the headset. 1 2 Gently lift and pull the top of the earhook up and off the upper hinge pin. Then, pull it away to remove it. 1 Open Earhook 2 Pull Earhook Up Hinge Pin 2 Loop the earhook over your ear. 3 Press earhook to your ear. When worn, your headset will look like this on your head: 2 3 3 Position the headset for right or left ear use (right ear use is displayed). 4 Hook the bottom of the earhook onto the lower hinge pin, then lift and pull the top of the earhook over the upper hinge pin. CHANGING VOLUME BUTTON ORIENTATION You can also change the orientation of the volume buttons on your headset. European Union Directives Conformance Statement Hereby, Motorola declares that this product is in compliance with: · The essential requirements and other relevant provisions of Directive 1999/5/EC. · All other relevant EU Directives. 1 Turn the headset power off. 2 Press and hold the Volume button you want to assign as the "volume up" button and slide the switch toward the microphone. The indicator light is either steadily lit or flashing in blue. Product Approval Number Volume Buttons The above gives an example of a typical Product Approval Number. Slide Switch You can view your product's Declaration of Conformity (DoC) to Directive 1999/5/EC (to R&TTE Directive) at www.motorola.com/rtte. To find your DoC, enter the product Approval Number from your product's label in the "Search" bar on the web site. MAKING CALLS Function Receive a call Mute or unmute a call Reject a call Action Tap the Call button Tap both Volume buttons Press and hold a Volume button until you hear two descending tones Tap the Call button Press and hold the Call button until you hear two ascending tones Tap the Call button and speak the name after the tone MAKING CALLS CONTINUED Function Answer a second incoming call End an active call and resume a call on hold Disable the indicator light Action Tap the Call button Tap the Call button First slide the switch toward charging plug (to turn headset off), then press and hold both Volume buttons AND slide the switch towards the microphone (to turn headset on) End a call Redial last call Make a voice dial call Note: Some features are phone/network dependent. Note: Your H550 supports both Handsfree and Headset Profiles. Accessing call functions depends upon which profile your phone supports. See your phone's user's guide for more information. INDICATOR LIGHTS With the Charger Plugged In Headset Indicator Headset Status Steady red Charging Off Charging complete With No Charger Plugged In Headset Indicator Headset Status Off Power off Steady purple Powering up Steady blue Pairing/connection mode 10 rapid purple flashes Connection successful Slow blue flash Standby (not on call) Quick blue flash Incoming call Slow blue pulse Connected (on a call) Slow purple pulse Connected (on a muted call) Red flash Idle (not connected) Quick red flash Low battery Note: After 30 minutes of inactivity, the light stops flashing to conserve power, but the headset remains in standby mode. AUDIO TONES Audio Tone Ring tone Single high tone High to low tone Single high tone when pressing volume button Two ascending tones Two descending tones Low to high tone Headset Status Incoming call Phone network not available End call Volume at minimum or maximum Mute enabled Mute disabled Connection confirmation/voice activation Out of range Low battery No audio indications; deteriorating quality Two tones repeated every 30 sec.