Movita junior User manual These operating instructions contain information, settings, safety precautions, which are to be considered with the use of Movita junior, as well as other important data. Movita junior are not to be used on diagonal and uneven ground. Movita junior are walking aids for children starting with age 7 and for adult body size from approx. 120 cm to 200 cm. Movita is directed mainly towards walk-obstructed people who, without support, cannot keep themselves upright. Movita can be adapted individually to the needs of the user. The thoracic support holds the upper body in an upright position and gives the user security. The pelvic support holds the child on the seat, and the handle gives a relieved support for the arms. The thoracic support and the pelvic support can be opened with a simple motion, thus makes the transfer particularly easy. Movita junior can be used indoors and outdoors, thanks to the large wheels. Start-up Movita junior will be delivered in two parts: the underframe with wheels and brakes and the upper section with seat and thoracic support. Under the seat a hexagonal wrench is located (fig. 2). Assembling upper section and underframe Upper section needs to be put on top of the underframe. Basic model adjustment Height of the thoracic support and seat For height adjustment of the thoracic support, loosen the two bottom handles (fig. 3). Once the desired height has been reached, the handles need to be tightened whereby the same height can be adjusted on both sides with the help of the height framework. The seat height can be adjusted by loosening both upper handles (fig. 4). Once the desired height has been achieved both handles need to be tightened, whereby with the help of the height framework the exact height can be adjusted. Thoracic support The thoracic support can be opened or closed through lightly raising or down-pressing the padded pipe (fig. 6). Springs The two springs in the lower pipes can be exchanged, if a harder or softer suspension is needed (fig. 5). The springs are available in four different levels of stiffness, which are appropriate for the following body weights 20 kg - 40 kg -60 kg -80 kg. Seat The seat can be pushed back and forward. Loosen the large screw under the seat attachment pipe (fig. 6). If the desired position is found the screw needs again to be tightened. In addition also the angle of the seat can be adjusted again by loosening the two internal hexagonal screws under the seat (fig. 6). After adjusting, the screws are tightened again. Manufacturer: elmi GmbH - Handwerkerzone 25 - I-39052 Kaltern - Tel 0471 961002 - FAX 0471 962374 elmisrl@tin.it www.movita.it -2- Movita junior User manual Pelvic support The pelvic support behind the seat can be lifted or pushed down; whereby an internal hexagonal screw becomes visible. If the screw is loosened the pelvic support can be pushed backwards or forwards (fig. 7). After adjusting, the screw is tightened again. Handle The handle is fastened to both sides by an aluminum part to the framework. The height and the length of the handle can be adjusted by opening the two internal hexagonal screws. After adjusting, the screws are tightened again. Safety precautions Warning: Never leave the user of Movita junior without supervision. CE- tested brand: Movita junior is provided with a CE-marking. Technical data length Movita junior 86 cm width seat height thoracic support height (side) thoracic support, perimeter wheels dimension front wheels dimension rear load in relation to shock absorbers frame wheels thoracic support and handle seat 69 cm 46-67 cm 76-97 cm 70/90/105/ 140x30 mm 400 x 40 mm 20 kg / 40 kg / 60 kg / 80 kg stainless steel tubular frame, powder coated full rubber, suitable for indoor and outdoor use covered with soft and anallergic rubber anatomic Abb. 11 Manufacturer: elmi GmbH - Handwerkerzone 25 - I-39052 Kaltern - Tel 0471 961002 - FAX 0471 962374 elmisrl@tin.it www.movita.it ...