WORLD CLASS HI FI OWNERS MANUAL CD Players: CDS3, CDX2, CD5x, CD5i IMPORTANT In order to comply with current European safety regulations it is essential that the Naim loudspeaker connectors supplied with amplifiers and loudspeakers are used. Do not under any circumstances allow anyone to modify your Naim equipment without first checking with the factory, your dealer, or your distributor. Unauthorised modifications will invalidate your guarantee. For your own safety do not under any circumstances open Naim equipment without first disconnecting it from the mains. Warning: an apparatus with CLASS I construction shall be connected to a mains socket outlet with a protective earthing connection. Where the mains plug or an appliance coupler is used as the disconnect device, the disconnect device shall remain readily operable. To disconnect the equipment from the mains remove the mains plug from the mains outlet. The following label is attached to all mains powered equipment: WA R N I N G THIS APPARATUS MUST BE EARTHED Contents Page Section 1 1 2 3 Equipment Installation Audio Connections Mains Power Connection General Installation CDS3 Installation and Operation CDS3 Connection Diagrams CDS3 Transit Screw and CD Loading Diagrams CDX2 Installation and Operation CDX2 Connection Diagrams 2 3 4 5 7 8 10 11 13 14 15 16 16 17 18 20 21 4 5 6 7 8 9 10 CD5x Installation and Operation 11 CD5x Connection Diagrams 12 CD5i Installation and Operation 13 CD5i Connection Diagrams 14 CDX2, CD5x and CD5i Transit Screw and CD Loading Diagrams 15 CD Puck Identification 16 CD Player Specifications 17 Flash Remote Handset 18 NARCOM 3 Remote Handset 19 iCOM Remote Handset 20 Declaration of Conformity NOTE This equipment has been tested and found to comply with the relevant EMC and Safety Standards, and, where applicable, also complies with the limits for a class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Increase the separation between the equipment and the receiver. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. · Consult your Naim dealer or an experienced radio/TV technician for help. Introduction Naim Audio products are conceived with performance as the top priority. Careful installation will help ensure that their full potential is achieved. This manual begins with general installation notes and statutory safety warnings for all Naim Audio products. Product specific information begins in Section 5. 1 Equipment Installation Normally your Naim Audio equipment will have been installed by the dealer who sold it to you - even if you live outside their immediate vicinity. In any event however your dealer is responsible for making sure that the system sounds as it should. Information given here is not intended to reduce this responsibility in any way. 2 Audio Connections It is important for both safety and performance that the standard cables supplied are not modified. 3.1 Mains Plug Wiring In some territories a mains plug may need to be fitted to the supplied mains lead. As the colours of the wires in the mains lead may not correspond with the coloured markings identifying the terminals in the plug proceed as follows: The wire which is coloured GREEN-AND-YELLOW must be connected to the terminal in the plug which is marked by the letter E or by the safety earth symbol or coloured GREEN or GREEN and YELLOW. The wire which is coloured BLUE must be connected to the terminal in the plug which is marked with the letter N or coloured BLACK. The wire which is coloured BROWN must be connected to the terminal in the plug which is marked with the letter L or coloured RED. 2.1 Interconnect Cables If options are available with your equipment and installation, DIN interconnect sockets should be used in preference to RCA Phono sockets. One end of each Naim interconnect cable is marked with a band to establish its correct orientation. The band denotes the end that connects to the signal source. Interconnect plugs and sockets should be kept clean and free from corrosion. The easiest way to clean them is to switch off the equipment, pull the plugs out of their sockets, and push them back in again. Contact cleaners and "enhancers" should not be used as the film they tend to deposit may degrade the sound. 2.2 Loudspeaker Cables Loudspeaker cables are vitally important and your dealer should make them up to suit your installation. The cables should each be at least 3.5 metres long and of equal length. The recommended maximum is normally 20 metres although longer cables may be viable with some Naim amplifiers. Contact your dealer or Naim Audio for advice. Many Naim amplifiers are designed only to work with Naim loudspeaker cable and using alternatives may degrade the performance or even damage the amplifier. Naim loudspeaker cable is directional and should be oriented so that the printed arrow points towards the speakers. The amplifier/loudspeaker connectors supplied are designed to make a robust electromechanical connection and to comply with European safety regulations. They should be used in preference to alternatives. 3.2 Non-rewirable Mains Plugs If a non-rewirable plug is cut from a mains lead (for whatever purpose) the plug MUST be disposed of in a way to render it totally useless. Considerable shock hazard exists if the cut-off plug is inserted into a mains outlet. 3.3 Mains Circuits and Cables A hi-fi system usually shares a mains circuit with other household equipment some of which can cause distortion of the mains waveform. This distortion can in turn lead to a mechanical hum from power amplifier and power supply transformers. Naim transformers are large in size with heavy gauge windings, making them relatively sensitive to such distortion, and it may be necessary to take account of transformer hum when siting your equipment. Transformer hum is not transmitted through the speakers and has no effect on the performance of the system; however, a separate mains circuit may reduce it. Such a circuit (ideally with a 30 or 45 Amp rating) will also improve system performance. Advice on the installation of a separate mains circuit should be sought from a qualified electrician. Do not substitute alternative mains leads and plugs to those supplied. They are selected to offer the best possible audio performance. 3 Mains Power Connection Where fused plugs are used 13 amp fuses should be fitted. Fuses of a lower rating will fail after a period of use. Do not wire voltage dependent resistors or noise suppressors into mains plugs. They degrade the mains supply and the sound. 1 Introduction 4 General Installation Naim equipment is designed to offer the finest sound quality possible avoiding compromise wherever practical. This can lead to circumstances that may be unfamiliar. The notes that follow contain advice specifically related to Naim equipment as well as more general warnings about the use of domestic audio products. Please read them carefully. 4.5 Non-standard Cables Use of non-standard speaker cables or interconnects may invalidate your guarantee. 4.6 Lightning Precautions Your Naim hi-fi system can be damaged by lightning. Power amplifiers are particularly at risk and should be turned off and disconnected from the mains when there is risk of lightning strike. For complete protection all mains plugs and any aerial cables should be disconnected when not in use. 4.1 Siting The Equipment In order to reduce the risk of hum audible from the loudspeakers, power supplies and power amplifiers should be located a reasonable distance away from other equipment. The maximum separation distance for connected equipment is that allowed by the standard interconnect lead. Some Naim equipment is extremely heavy. Ensure that your equipment rack or table can easily support the weight and is stable. 4.7 Liquid Precautions Equipment must not be exposed to dripping or splashing and no objects filled with liquid, such as vases, should be placed on the equipment. 4.8 Equipment Fuses Mains powered Naim Audio equipment is fitted with a mains input fuse on the rear panel adjacent to the mains input socket. Replace it if necessary only with the spare fuse supplied or with identical fuses. Repeated failure of this fuse points to an equipment or system fault that should be investigated by your dealer or at the factory by Naim itself. 4.2 Switching On Source components and power supplies should be switched on before the power amplifiers. Always switch amplifiers off and wait a minute before connecting or disconnecting any leads. Always use the power switch on the product rather than a mains outlet switch. A "thump" may be heard from the loudspeakers as power amplifiers are switched on. This is normal, will not cause any loudspeaker damage and does not point to any fault or problem. A mild "pop" may also be heard shortly after power amplifiers are switched off. 4.9 Problems? Consumer protection varies from country to country. In most territories a dealer must be prepared to take back any equipment he has sold if it cannot be made to work satisfactorily. A problem may be due to a fault in the system or its installation so it is essential to make full use of your dealer's diagnostic skills. Please contact your local distributor, or Naim Audio directly, if any difficulties cannot be resolved. Some Naim equipment is made in special versions for different territories and this makes it impracticable to arrange international guarantees. Please establish the local guarantee arrangements with your dealer. Contact Naim Audio directly for help and advice if necessary. 4.3 Running In Naim equipment takes a considerable time to run in before it performs at its best. The duration varies, but under some conditions the sound may continue to improve for over a month. Better and more consistent performance will be achieved if the system is left switched on for long periods. It is worth remembering however that equipment left connected to the mains can be damaged by lightning. 4.10 Repairs and Updates It is essential that repairs and updates are only carried out by an authorised Naim dealer or at the factory by Naim itself. Many components are custom made, tested or matched and appropriate replacements are often unobtainable from other sources. Direct contact to Naim for service or update information should be made initially through the Service Department: Tel: Email: +44 (0)1722 332266 service@naim-uk.com 4.4 Radio Interference In some circumstances, depending on where you live and the earthing arrangements in your home, you may experience radio frequency interference. Controls on broadcasting in some territories allow very high levels of radio frequency radiation and both the choice and exact siting of equipment may be critical. Susceptibility to radio frequency interference is related to the wide internal bandwidth necessary for high sound quality. Systems incorporating moving coil phono preamplifiers and active crossovers are more likely to suffer. A radio frequency filter kit is available for some Naim equipment but sound quality will be progressively compromised as more elements of the kit are fitted. In situations of extreme radio interference Naim equipment may be unsuitable. Please quote the product serial number (found on its rear panel) in all correspondence. 2 CDS3 5 Installation and Operation The CDS3 CD Player can only be operated from a Naim XPS Power Supply. Connection of the power supply is illustrated in Diagram 6.2 The CDS3 should be installed on a dedicated equipment stand intended for the purpose. To improve sound quality the player has hard metallic feet which may blemish any delicate surface on which it is placed. Do not stand the player directly on top of another item of Naim Audio equipment. Care should be taken to ensure that the player is level. Transit screws on the underside of the CDS3 case and beneath its transport lid should be removed before use and must be replaced if the unit is to be moved or re-packed and shipped. The transit screw locations are illustrated in Section 7. The transit screws must not be used in any other Naim product. Do not invert the player once the transit screws are removed. 5.1 Disc Loading Disc loading is illustrated i ...