PATIO HEATER -PTH38PSS-PTH38PCP-PTH38PGMWARNING: For Outdoor Use Only. FOR YOUR SAFETY If you smell gas: 1. Shut off gas to the appliance. 2. Extinguish any open flame. 3. if odor continues ,immediately call gas supplier. OFF GH HI FOR YOUR SAFETY Do not store or use gasoline or other flammable vapors or liquids in the vicinity of this or any other appliance. CAUTION: Retain the instructions for future use. DE SIGN CERTIFIED E RTIFIE Manual,Instructions & Parts List D C TOOLS AND PARTS NEEDED FOR ASSEMBLY DANGER CARBON MONOXIDE HAZARD This appliance can produce carbon monoxide which has no odor. Using it in an enclosed space can kill you. Never use this appliance in an enclosed space such as a camper, tent, car or home. adjustment, alteration, services or maintenance can cause injury, death or property damage. Read the installation, operating and maintenance instructions thoroughly before installing or servicing this equipment. WARNING: Improper installation, TOOLS NEEDED: 7/16" Wrench 3/8" Open End Wrench Adjustable Opening Wrench, 8" Long Philips Head Screwdriver Leak Detection Solution ( Instructions how to make solution are included in Step 8 ) WARNING For outdoor use only. Cylinders to be used must be constructed and marked in accordance with US DOT specifications. Storage indoors is permissible only if the cylinder is removed. The unit should be secured or moved indoors if winds exceed 35 km/h. Note: 20 Pound, 5 Gallon LPG Tank is not supplied 2 PARTS 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 1 4 1 1 1 1 3 1 Center Reflector Cap Reflector Cap Head Assembly Gas Hose Post Cylinder Cover Post Mounts Cylinder Base 15 16 10 9 1 2 15 M6 Nuts 18 6mm Washers 6 5 5 6 5mm Washers 4mm Washers M4 x 8 Bolts M5 x 8 Bolts 3 4 13 12 M6 x 10 Bolts 3 1 1 M6 x70 double pointed bolts Regulator Cylinder (Not Supplied) 5 6 9 10 11 12 14 13 14 15 16 17 7 17 8 3 PRECAUTIONS NOTE: PLEASE READ THE FOLLOWING SAFETY RULES This appliance must only be used outdoors. Using this product in an enclosed area may cause injury, death or property damage. Read the instructions before use. This appliance must be installed in accordance with such regulations as are in force. Do not use the heater in an explosive atmosphere. Keep the heater away from areas where gasoline or other flammable liquids or vapors are stored. Prior to use, check for damaged parts such as hoses, regulators, pilot or burner. The installation of fixed appliances shall only be carried out by competent persons and be in accordance with the relevant Codes of Practice. Warning: This appliance requires a gas hose and regulator, check with your gas supplier and or product supplier. Regularly check the gas hose and if necessary, replace the gas hose. DISCONNECT LPG bottle before moving the heater. Do not attempt to alter unit in any manner. EXAMPLE: using the heater without the top canopy reflector or radiant screen. Do not shorten the burner post assembly. The appliance shall not be used in basements or below ground level. It must always be placed on a solid and level surface. Always assure there is ample fresh air ventilation. For outdoor use ONLY . Never replace or substitute the regulator with any regulator other than the factory suggested replacement. Do not clean the heater with cleaners that are combustible or corrosive. Do not paint radiant screen, control panel or top canopy reflector. All leak tests should be done with a soapy solution. NEVER USE AN OPEN FLAME TO CHECK FOR LEAKS. The LP gas cylinder should be turned off when the heater is not in use. WARNING At least once a year, the unit should be inspected for the ¥ presence of spiders, spider webs or other insects. Check the heater immediately if any of the following exist: 1. The smell of gas in conjunction with extreme yellow colored tips of the burner flames. 2. The heater does not reach temperature. 3. The burner makes popping noise during use (a slight popping noise is normal when the burner is extinguished after using). The propane hose with regulator assembly shall be located out of pathways where people may trip over it or in areas where the hose will not be subject to accidental damage. Children and adults should be aware of the hazards of high surface temperature and shall stay away to avoid clothing burn or ignition. Young children should be carefully supervised when they are in the area of the heater. Clothing or other flammable material should not be hung from the heater, or placed on or near the heater. Any guard or other protective device removed for servicing the heater must be replaced prior to operating the heater. Installation and repair should be done by a qualified service person. The heater should be inspected before use and cleaning may be required at least once a year, or as necessary. It is imperative that control compartment, burner and circulating air passageways of the heater be kept clean. Keep the appliance area clear of combustible materials such as gasoline and other flammable vapors and liquids. Do not obstruct the flow of combustion and ventilation air. Keep the ventilation opening of the cylinder enclosure free and clear of debris. 4 ASSEMBLY FOR LIGHT SYSTEM WARNING: TO BE INSTALLED ONLY BY AN AUTHORISED PERSON Instruction For Battery Installing Upon first time use of the product,please remove the ignition button and install an AAA battery as indicated. Ignition button Control knob Replace Battery Ignition button AAA battery 5 ASSEMBLY NOTE: Assembly of this heater requires basic mechanical skills. Proper assembly is the responsibility of the installer. Step 1 ---- Attach Post to Base Assembly Attach the post to the post mounts using M5 X 8 bolts (6 pcs) and 5mm washers (6 pcs) Step 1 5 11 14 7 Step 2 ---- Attach Cylinder Cover to Post Mounts Attach the cylinder cover to the post mounts. Step 2 6 7 6 ASSEMBLY NOTE: Assembly of this heater requires basic mechanical skills. Proper assembly is the responsibility of the installer. Step 3 ---- Attach Head Assembly to Post Load head assembly by inserting gas hose into post. Insert head assembly into post. Tighten securely using M4 X 8 Bolts (5 pcs) and 4mm washers (5 pcs). Step 3 3 4 12 13 5 Step 4 Step4 ---- Attach Double Pointed Bolt to Head Assembly Attach M6 X 70 double pointed bolts (3 pcs) and 6mm washers (3 pcs) to the top of head assembly and tighten the bolts securely. 10 16 3 7 ASSEMBLY NOTE: Assembly of this heater requires basic mechanical skills. Proper assembly is the responsibility of the installer. Step 5 9 10 Step 5 ---- Attach Center Reflector to Reflector Attach center reflector to the top of reflector (4 pcs) by M6 X 10 mm screws (12 pcs) , 6mm washers (12 pcs) and nuts (12 pcs). 1 15 2 Step 6 ---- Attach Center Reflector and Reflector to the top of Head Assembly Load center reflector and reflector to the top of head assembly by M6 X 70 double pointed bolts (3 pcs) 6mm washers (3 pcs) and nuts (3 pcs) Step 6 9 10 3 8 ASSEMBLY NOTE: Assembly of this heater requires basic mechanical skills. Proper assembly is the responsibility of the installer. Step 7 ---- Connect Gas Line to Cylinder Attach Gas hose to regulator with 3/8 Inch Open End Wrench and Adjustable Wrench. Attach regulator to cylinder. Tighten securely. Move cylinder to the plate of base assembly. Step 7 Step 8 ---- Check for leak Your Patio Heater has been checked at all factory connections for leaks, To check the Connection of the gas hose/regulator/cylinder. 1) Make leak solution by mixing 1part liquid dish soap and 3 parts water. 2) Spoon several drops (or use squirt bottle) of the solution onto the gas hose/regulator and regulator/cylinder connection. 3) Inspect the connections and look for bubbles. 4) If no bubbles appear, the connection is safe. 5) If bubble appear, there is leak, loosen and re-tighten this connection. Step 8 9 ASSEMBLY WARNING : TO BE INSTALLED ONLY BY A COMPETENT PERSON Step 9---- Lower Cylinder Cover onto Cylinder Base Lower the cylinder cover onto the cylinder base . Step 9 6 8 Step 10---- Disconnect Cylinder When Storing or Transporting 1).Turn off the heater; 2).Upper the cylinder cover onto the post mounts; 3).Turn off the valve of the cylinder; 4).Loosen the screw of cylinder and regulator; 5).Disconnect the cylinder from regulator. Step 10 6 7 10 OPERATION WARNING: DO NOT attempt to operate heater until you have read and understand all precautions. Failure to do so can result in serious personal injury, death or property damage. Before Turning Gas Supply ON FOR YOUR SAFETY: WA R N I N G Your heater was designed and approved for OUTDOOR USE ONLY. Do NOT use it inside a building ,or any other enclosed area. Make sure surrounding areas are free of combustible materials, gasoline and other flammable vapors or liquids. Ensure that there is no obstruction to air ventilation. Be sure all gas connections are tight and there are no leaks. Be sure the access panel is clear of debris. Be sure any component removed during assembly or servicing is replaced and fastened prior to starting. If at any time you are unable to light burner and smell gas, wait 5 minutes to allow gas to dissipate before attempting to light heater. If, after 1 minute, you are unable to light burner, wait 5 minutes and allow flammable vapors to dissipate before attempting to light heater again. Before Lighting Heater should be thoroughly inspected before each use, and by a qualified service person at least annually. If relighting a hot heater, always wait at least 5 minutes. Our heater is tested for quality assurance. Ignition attempts should succeed 8 out of 10 attempts. at least 45 minutes after use. Allow emitter and dome to cool before touching. FOR YOUR SAFETY: DO NOT touch or move heater for WA R N I N G LIGHTING INSTRUCTIONS 1) Turn the control knob to "OFF" position. 2) Fully open gas valve 3) Depress control knob and turn knob counter-clockwise to PILOT whilst simultaneously pressing the electronic ignition button until light the pilot. 4) Once the pilot is lit, continue to keep the control knob depressed for at least 30 seconds, After 30 seconds release control knob. 5) If pilot does not stay lit, repeat steps 3 and 4. 6) If pilot still does not stay lit, then: a) Push in gas control knob and turn counter clockwise to "PILOT" b) keep depressing the control knob, put long stem lighter into the Ignition Hole on the emitter screen to light the pilot. c) repeat step 4. 7) Push in and turn control knob counter clockwise to "LOW" position, release knob then turn to low. If you want a higher temperature, push in the control knob and turn counter clockwise to the "HIGH" position. OFF Pu sh to P IL O T turn W OFF Pu sh to P IL O T W Note: The flame pattern at the emitter grid should be visually checked whenever heater is operated. Normally the burner flame is blue, but little yellow flame is acceptable. If flames extend beyond surface of the emitter grid , or the phenomena of flame lift or light back, or black spot is accumulating on the emitter grid or reflector, the heater should be turned off immediately. The heater should not be operated again until the unit is serviced and or repaired. If you experience any ignition problem, turn off the heater and gas supply, and consult "Troubleshooting" on page 15. Emitter Screen Ignition Hole 11 GH HI GH HI turn LO LO OPERATION CAUTION : Avoid inhaling fumes emitted from the heater's first use. Smoke and odor from the burning of oils used in manufacturing will appear. Both smoke and odor will dissipate after approximately 30 minutes. The heater should NOT produce thick black smoke. The burner may be noisy when initially turned on. To eliminate excessive OW noise from the burner, turn the Control Knob to the " LOW " position. Then, turn the knob to the level of heat desired. Warning: White smoke may appear around the radiant head during the first minutes of the initial firing. OFF Pu NOTE: sh to P IL O T turn W When heater is ON: Emitter screen will become bright red due to intense heat. The color is more visible at night. Burner will display tongues of blue flame. These flames should not be yellow or produce thick black smoke, indicating an obstruction of airflow through the burners. Operation Pressure Checked If the flame is very small, this is because the supply pressure is not enough. RELIGHT OW 1)Turn the control knob to " OFF " position. 2)Wait five (5) minutes before attempting to relight pilot. 3) Repeat steps beginning with step 2 above. Before Leaving 1)Turn the control knob to "OFF" position and Turn LP cylinder to "OFF" position. 2)Never leave the patio heater unattended while in use. OFF Pu P IL O T SHUT DOWN INSTRUCTIONS 1) Push in and turn control knob clockwise to "OFF" position. 2) Turn L.P. tank gas valve clockwise to "OFF" position when heater is not in use Note: After use, some discoloration of the emitter screen is norma ...