User manual NAVMAN ICN 700 WITH SMARTS 2006

USER MANUAL N Pix Navig av to pictu r ate iCN 700 with SmartSTM 2006 series en English - Europe/New Zealand es iCN 700 series User Manual English - Europe / New Zealand © 2006 Brunswick New Technologies Asia Pte Limited. Navman is a registered trademark of Brunswick New Technologies Asia Pte Limited and is used under licence by Navman New Zealand. Navman is part of the Brunswick Group, headquarters Chicago, IL. All rights reserved. The software contains proprietary information of Navman; it is provided under a licence agreement containing restrictions on use and disclosure and is also protected by copyright law. Reverse engineering of the software is prohibited. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or otherwise, without the prior written permission of Navman. Back-On-Track, Drive-Away, NavPix, Smart and Turn-by-Turn are either registered trademarks or trademarks of Brunswick New Technologies Asia Pte Limited and are used under licence by Navman New Zealand. All rights reserved. Microsoft Windows 2000 and XP SP1, Microsoft Internet Explorer and ActiveSync are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. All rights reserved. Adobe and Adobe Reader are either registered trademarks or trademarks of Adobe Systems Incorporated in the United States and/or other countries. All rights reserved. Location Identifiers © 2005 International Air Transport Association. All other trademarks and registrations are the property of their respective owners. Published in New Zealand. Disclaimer Due to continued product development this information may change without notice. Navman does not warrant that this document is error-free. The screenshots and other presentations shown in this User Manual may differ from the actual screens and presentations generated by the actual product. All such differences are minor and the actual product will deliver the described functionality as presented in this User Manual in all material respects. Compliance This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The software is based in part on the work of the Independent JPEG Group. iCN 700 series | Important safety information Important safety information PLEASE READ CAREFULLY BEFORE INSTALLING PRODUCT IN VEHICLE This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death. WARNING indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. CAUTION indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. CAUTION used without the safety alert symbol indicates a potentially hazardous situation which, if not avoided, may result in property damage. Removing original equipment, adding accessories or modifying your vehicle could affect the vehicle's safety or make it illegal to operate in some jurisdictions. Follow all product instructions and all instructions in your vehicle owner's manual regarding accessories or modifications. Consult your country's and/or state's laws regarding operation of a vehicle with any accessories or modifications. It is your sole responsibility to place, secure and use the iCN in a manner that will not cause accidents, personal injury or property damage. Always observe safe driving practices. Mount the iCN in a position that is secure and does not obstruct the driver's view. Do not mount the iCN in a way that may interfere with the safe operation of the vehicle, the deployment of air bags or other safety equipment. Do not operate the iCN while driving. Before you use your iCN for the first time, familiarize yourself with your device and its operation. On main roads, the distance to an exit calculated by the iCN may be further than the distance shown on road signs. Road signs show the distance to the start of an exit while your iCN shows the distance to the next intersection, i.e., the end of the exit ramp or road. To prepare to exit a road, always follow distance information on road signs. 5 iCN 700 series | Important safety information Do not handle the iCN while it is hot. Let the product cool, out of direct sunlight. Do not expose the iCN to direct sunlight in an unattended vehicle for prolonged periods. Overheating may damage the unit. To discourage theft, do not leave the iCN, mounting bracket or any cables in plain view in an unattended vehicle. Failure to adhere to these warnings and cautions may lead to death, serious injury or property damage. Navman disclaims all liability for installation or use of the iCN that causes or contributes to death, injury or property damage or that violates any law. 6 iCN 700 series | Contents Contents Important safety information...................................................................................................................5 Welcome................................................................................................................................................9 Box contents ...................................................................................................................................10 Typographical conventions .............................................................................................................11 Getting to know your iCN ................................................................................................................12 Front components.......................................................................................................................12 Side components........................................................................................................................13 Top components.........................................................................................................................14 Bottom components....................................................................................................................14 Back components .......................................................................................................................15 Volume .......................................................................................................................................15 Internal battery............................................................................................................................16 How do I get started?...........................................................................................................................17 How do I turn my iCN off? ...............................................................................................................19 What are the main screens that I will use?...........................................................................................20 How do I navigate with GPS? ..............................................................................................................22 How do I go from A to B? .....................................................................................................................23 How do I search for an address? ....................................................................................................24 Case Study: How do I search for an address?...........................................................................24 Using the Keyboard screen ........................................................................................................27 Using the Destination Search screen..........................................................................................27 How do I create a trip with multiple stops? ......................................................................................30 Case Study: How do I navigate to multiple addresses? .............................................................31 How do I skip a waypoint during a multi-stop trip? ......................................................................35 How do I search for a landmark or venue?......................................................................................36 How do I find the nearest petrol station?.....................................................................................36 How do I find the nearest parking area? .....................................................................................37 How do I search for other POIs?.................................................................................................38 Case Study: How do I search for a Point of Interest?.................................................................38 How do I view my route?......................................................................................................................41 3D Map screen ...............................................................................................................................42 2D Map screen ...............................................................................................................................44 Next Turn screen ............................................................................................................................46 Direction List screen .......................................................................................................................47 What if I miss a turn? ......................................................................................................................48 How do I save Favourites and My Home?............................................................................................49 How do I save a Favourite? ............................................................................................................49 How do I navigate to a Favourite?...................................................................................................50 How do I navigate to My Home? .....................................................................................................51 How do I view details of a Favourite?..............................................................................................52 How do I edit the name of a Favourite? ..........................................................................................53 How do I delete a Favourite? ..........................................................................................................54 How do I use the camera? ...................................................................................................................55 How do I view the Camera screen? ................................................................................................56 How do I take a photo? ...................................................................................................................57 How do I customize camera preferences?..................................................................................58 How do I manage my photos? ........................................................................................................59 Album management ...................................................................................................................59 Photo management ....................................................................................................................61 7 iCN 700 series | Contents How do I save, e-mail or print photos?............................................................................................63 Via Memory Card........................................................................................................................63 Via USB cable ............................................................................................................................63 How do I navigate to a photo location? ...........................................................................................65 How do I assign a photo to a Favourite? .........................................................................................66 What else can I do? .............................................................................................................................67 How do I navigate to a recent location? ..........................................................................................68 How do I use the Map Menu? .........................................................................................................69 How do I avoid an area? .................................................................................................................71 How do I preview a route? ..............................................................................................................72 How do I view my route statistics? ..................................................................................................74 How do I view statistics on my current route? .............................................................................74 How do I view statistics of my trips to date?................................................................................75 What is SmartST Desktop?..................................................................................................................76 Can I use Smart Desktop with my computer? ........................................................................77 What is Microsoft ActiveSync®? ..................................................................................................77 How do I install a map for the first time? .....................................................................................77 How do I install Smart Desktop on my computer? ......................................................................78 Smart Desktop features..............................................................................................................79 Toolbars .....................................................................................................................................81 How do I keep Smart up-to-date?..............................................................................................82 How do I install maps on my iCN? ..................................................................................................83 How do I install maps from CD? .................................................................................................83 How do I know which map contains a particular city or town?.....................................................86 What is a Major Road Network map? .........................................................................................87 How do I install Custom Points of Interest?..........................................................................................88 How do I create a Custom POI file?............................................................................................89 How do I copy a Custom POI file to my iCN?.............................................................................90 How do I backup my iCN?...............................................................................................................93 Reference ............................................................................................................................................94 What can I customize?....................................................................................................................95 Route Preferences......................................................................................................................96 Tutorial .......................................................................................................................................99 System Preferences ...................................................................................................................99 Display Preferences .................................................................................................................103 POI Preferences .......................................................................................................................107 Which maps are already installed on my iCN? ..............................................................................110 How do I use a memory card with my iCN? ..................................................................................111 How do I insert a Memory Card? ..............................................................................................112 How do I remove a Memory Card? ...........................................................................................112 Address search rules ....................................................................................................................113 Street types - Europe ....................................................................................................................114 Points of Interest categories..........................................................................................................118 Specifications................................................................................................................................120 Support information............................................................................................................................121 Notes .................................................................................................................................................122 8 iCN 700 series | Welcome Welcome Thank you for purchasing this Navman iCN. This user manual has been prepared to guide you through the operation of your Navman iCN from first set-up through to continuous use, and will help you Drive-AwayTM with your iCN, straight out of the box. Please read this manual carefully before using your iCN for the first time. Keep this manual available for future reference. In this section Box contents........................................................................................................................................ 10 Typographical conventions .................................................................................................................. 11 Getting to know your iCN..................................................................................................................... 12 9 iCN 700 series | Welcome Box contents Item iCN with GPS receiver Item Mounting bracket AC Power pack with power cable and plugs The number of plugs included depends on the country of purchase. 12V In-vehicle power adaptor with power cable USB cable CDs include: Smart 2005 software, including Smart Desktop Map data User Manual (PDF) and ® ® Adobe Reader The number of discs included depends on the country of purchase. User Manual In-Car Installation Guide GPS Frequently Asked Questions guide Global Support Information Software Product Licence and Limited Warranty Agreement Registration card 10 iCN 700 series | Welcome Typographical conventions It is important to understand the terms and typographical conventions used in this manual. Formatting The following kinds of formatting in the text identify special information: Convention Bold Italics Type of Information iCN components or items displayed on screen, including buttons, headings, field names and options. Indicates the name of a screen. Icons The following icons are used throughout this manual: Icon Description Note Important note Tip Case study Warning Terms The following terms are used throughout this manual to describe user actions. Term Press Select Tap Tap and hold Description Press and release a button quickly. Tap an item in a list or tap a command from a menu. Press and release an item displayed on the touch screen. Press and hold an item displayed on the touch screen for 2-3 seconds. 11 iCN 700 series | Welcome Getting to know your iCN We recommend that you familiarize yourself with the iCN's basic operations. Front components Component Battery indicator Description Indicates the level of internal battery charge: Green - battery full Red - battery low Orange - battery charging For more information, see "Internal battery" on page 16. Touch screen Displays maps and menu options. Tap to select menu options or enter information. Displays a list of the nearest petrol stations based upon your current location. Displays a list of the nearest parking areas based upon your current location. Displays the Main Menu screen. For more information, see "What are the main screens that I will use?" on page 20. Displays the Go To menu screen. For more information, see "What are the main screens that I will use?" on page 20. Cycles through the 3D Map, 2D Map, Next Turn and Turn List screens. For more information, see "What are the main screens that I will use?" on page 20. 12 iCN 700 series | Welcome Side components Component External antenna socket Description Connection socket for GPS MCX External Antenna (not included). Connection socket for headphones or earphones (not included). Slot for memory card. The memory card must be inserted with the label facing the front of the iCN. For more information on inserting the memory card, see "How do I use a memory card with my iCN?" on page 111. Connection socket for AC power-pack or in-vehicle power adaptor. Connection socket for USB cable to your computer. Volume control Rotate up or down to hear a sound test and adjust the volume. Press to mute the volume. 13 iCN 700 series | Welcome Top components Component Description Turns the iCN on or off; when off, the iCN enters a suspended state. Turns the camera on. Press to take a photo. Bottom components Component RESET BATTERY Hot shoe plate Description Resets the iCN. For more information, see "How do I turn my iCN off?" on page 19. Must be set to ON for normal use. Switching to OFF turns the battery off, which saves battery power. Connection plate for the P1 or T1 module. 14 iCN 700 series | Welcome Back components Component Camera Speaker GPS receiver Description The camera lens. Broadcasts voice commands and warnings. Use the Volume control to adjust. Receives signals from GPS satellites when lifted out to the horizontal position. Volume The volume on your iCN can be adjusted either by the volume control on the iCN or by using the three volume control buttons on the remote control (may be sold separately). These are described below: Volume Control on iCN To hear a sound test and adjust the volume, rotate the Volume control up or down. The volume bar displays as green. To mute the volume, press the Volume control. The volume bar displays as grey, and indicates that the volume is muted. To make the volume active, rotate the Volume control up or down. The volume bar displays as green. 15 iCN 700 series | Welcome Internal battery The iCN has an internal battery that, when fully charged, should power the iCN for up to 2.5 hours. The battery indicator light on the front of the iCN indicates the level of internal battery charge: Green - battery full Red - battery low Orange - battery charging How do I monitor the battery status? You can monitor battery power status at the Power screen. For more information, see "Power" on page 101. How do I charge the internal battery? The Battery Status bar displays Charging while the battery is under charge; when the battery is fully charged, the Battery Status bar will display at 100%. To charge the iCN in a vehicle, plug the vehicle power adaptor into into the vehicle power socket. on the side of the iCN and the other end on the side of the iCN and the To charge the iCN using an electrical wall outlet, plug the AC power cable into AC power pack into the wall outlet. 16 iCN 700 series | How do I get started? How do I get started? Before you begin, check if your vehicle is fitted with a heat-reflective or heated windscreen. If so, you will need to purchase an external antenna for your iCN to receive GPS signals. For more information, see the GPS Frequently Asked Questions guide. To get started for the first time, complete the following steps: Step 1 2 3 4 Action Turn your iCN on. Select your preferred language. Accept the warning message. View the Tutorial. 1. Turn the iCN on a) Position the iCN in your vehicle according to the instructions in the In-Car Installation Guide. Please ensure that: the iCN does not obstruct the driver's view, or interfere with the operation of the vehicle airbags and safety devices. the GPS receiver is facing the sky directly above it, to allow it to obtain a GPS fix through the windscreen. the BATTERY switch is ON. The BATTERY switch is GREEN when ON and RED when OFF. b) Press to turn your iCN on. The iCN will turn on and display the Language screen. If your iCN was last turned OFF via the BATTERY switch, it will automatically turn on when the BATTERY switch is switched ON. If you have maps installed from multiple continents, you may be prompted to select the maps you would like to load before the Language screen is displayed. To use maps from a different continent at a later time, you must first reset your iCN, then select a different continent. 17 iCN 700 series | How do I get started? 2. Select your preferred language From the Language screen, tap your preferred language. To prevent the Language screen from displaying on each startup, tap the Show on startup check box. You can change your preferred language while using your iCN. For more information, see "Language" on page 101. 3. Accept the warning message a) b) The Warning screen will display when you have selected your preferred language. Read the Warning message. To confirm that you have read and understood the message, tap Accept. The Tutorial will display. 4. View the Tutorial When you have accepted the Warning message, the Tutorial will display. Read the Tutorial: To prevent the Tutorial from displaying again on startup, tap the Show on start-up check box to clear it. To move forward through the Tutorial screens, tap . To revisit the previous screen, tap . You can view the Tutorial again while using your iCN. For more information, see "Tutorial" on page 99. When you have finished the Tutorial, the 3D Map screen will display. If you have a GPS fix, your current location will be displayed on the map. For information on GPS, see "How do I navigate with GPS?" on page 22. 18 iCN 700 series | How do I get started? How do I turn my iCN off? To turn your iCN off, press . Your iCN will enter a suspended state and the screen will turn off. When you turn your iCN on again, it will return to the screen you were last viewing. Power-saving suspended state To save power, your iCN will automatically enter a suspended state after a pre-determined period of time. You can change the default suspended state setting at the Power preference screen. For more information, see "Power" on page 101. If battery power is very low, your iCN will enter a suspended state whether you have set a pre-determined period of time or not. If you are not going to be using your iCN for an extended period of time, switch the BATTERY switch to OFF to save battery power. How do I reset my iCN? Normally you do not need to reset your iCN; however, should your iCN not turn on or not respond, you can reset it to solve the problem. To reset your iCN, press the white RESET button on the bottom of your iCN. Your iCN will restart. 19 iCN 700 series | What are the main screens that I will use? What are the main screens that I will use? Map screens There are four map screens used to view the route to your destination: 3D Map 2D Map Next Turn Direction List To display the 3D Map screen, or the map screen that you were last viewing, press the map screens. ; press again to cycle through For more information on the map screens, see "How do I view my route?" on page 41. For information on using the Map menu from the 3D Map and 2D Map screens, see "How do I use the Map Menu?" on page 69. Main Menu screen The Main Menu screen provides access to all of the iCN's navigation functions. To access the Main Menu at any time, press ; to select a Main Menu option, tap the required icon. 20 iCN 700 series | What are the main screens that I will use? Go To Menu screen The Go To Menu screen is your starting point for specifying a destination. From the Go To Menu screen you can navigate to My Home, an address, Point of Interest, Favourite, recent location or set a multi-stop trip. To access the Go To Menu at any time, press option, tap the required icon. , or tap from the Main Menu screen; to select a Go To Menu For information or setting your destination, see "How do I go from A to B?" on page 23. 21 iCN 700 series | How do I navigate with GPS? How do I navigate with GPS? The Global Positioning System (GPS) is available at any time, free of charge, and is accurate to within 5m (15ft). GPS navigation is made possible by a network of satellites that orbit the Earth at around 20,200km. Each satellite transmits a range of signals which are utilized by GPS receivers, such as your iCN, to determine an exact location. Although a GPS receiver can detect signals from up to 12 satellites at any time, only four signals are required to provide a position or "GPS fix" (latitude and longitude), for vehicle navigation systems. Your iCN receives GPS signals via the GPS antenna. To guarantee the optimum GPS signal strength, ensure your iCN is outdoors, or in a vehicle outdoors and the GPS antenna has an unobstructed view of the sky. Your iCN can operate in all weather types except snowfall. You can view your GPS status at any time from the map screens or the camera screens. The GPS icon displays green when a GPS fix is established and red when a GPS fix is unavailable. To indicate the reception strength of a displays between one and four green quadrants. GPS fix, To see your GPS status in more detail, see "GPS Status" on page 100. For more GPS information, see the GPS Navigation - Frequently Asked Questions guide. 22 iCN 700 series | How do I go from A to B? How do I go from A to B? Your iCN is equipped with maps that provide street-level detail for door-to-door navigation, including Points of Interest (POIs) such as accommodation, parking areas, petrol stations, railway stations and airports. When you ... know the address of your destination have multiple stops Then ... use the address-entry wizard to enter the address, see "How do I search for an address?" on page 24. use the Multi-stop Trip Planner screen to enter multiple waypoints, see "How do I create a trip with multiple stops?" on page 30. search for a Point of Interest, see "How do I search for a landmark or venue?" on page 36. select from a list of the nearest petrol stations, see "How do I find the nearest petrol station?" on page 37. select from a list of the nearest parking areas to your current location, see "How do I find the nearest parking area?" on page 37. need to find a named site, feature, landmark or public venue need to find a petrol station need to find a parking area WARNING For your safety, enter destination information before you start a journey. Do not enter a destination while driving. In this section How do I search for an address? ......................................................................................................... 24 How do I create a trip with multiple stops?........................................................................................... 30 How do I search for a landmark or venue? .......................................................................................... 36 23 iCN 700 series | How do I go from A to B? How do I search for an address? Select a destination using the Destination Search, Keyboard and Destination Preview screens, which used together form an address-entry wizard. This section describes how to use each of these screens and provides a case study to help guide you through setting your destination. Quick Steps 1. 2. 3. 4. 5. 6. Open the Destination Search screen Select the country Search for the city/area Search for the street Search for the house number Tap Go. Case Study: How do I search for an address? This case study will show you how to set your destination by selecting your country, then area, then street, then house number. 1. Open the Destination Search screen The Destination Search screen will display. If this is the first time you are setting your destination and you have maps from more than one country installed and selected, then the Select Country screen will display instead of the Destination Search screen. Go directly to step 2b. The next time you perform this procedure, the Destination Search screen will open as expected. 24 iCN 700 series | How do I go from A to B? 2. Select the country If you only have the map of one country installed and selected, that country is selected for your destination by default and cannot be changed. Go to step 3. a) From the Destination Search screen, tap Change Country. The Select Country screen will display. Select a country from the list. The Destination Search screen will display. 3. Search for the City/Area a) From the Destination Search screen, tap City/Area. The Keyboard screen will display. b) Use the Keyboard screen to search for the city or area of your destination. The Destination Search screen will display. 25 iCN 700 series | How do I go from A to B? 4. Search for the street a) From the Destination Search screen, tap Street. The Keyboard screen will display. There may be multiple matches for a particular street name. Long streets that run through several neighbouring areas, and common street names; for example, Main Street, will produce matches that are distinguished by their associated city or area name. b) Use the Keyboard screen to search for the street of your destination. Where there are multiple matches, select the city or area that best describes your destination. The Destination Search screen will display. If house numbers and intersection information are not available for your selected street, the Destination Preview screen will display. Go to step 5c. 26 iCN 700 series | How do I go from A to B? Using the Keyboard screen The Keyboard screen will display when you are required to enter text, such as when searching for a street name. As you tap each character, the first two matching results will display. Tap to see more search results. Search results will be listed in matching order, with the closest matches appearing at the top of the list. A maximum of 99 results will display. The Keyboard screen can display in three modes: alphabet, alternate and number/symbol. As you select each character, the first two results will display. Tap to see more search results. To select a character or a search result, tap the character or search result. To delete a character, tap . To display the number/symbol Keyboard screen, tap 123. To display the alternate Keyboard screen, tap alt. To display the alphabet Keyboard screen, tap abc. Using the Destination Search screen As you specify each part of the address, it will display at the top of the screen. The available options will change to reflect the parts of the address still to be completed. 27 iCN 700 series | How do I go from A to B? 5. Search for the house number a) From the Destination Search screen, tap House Number. The Keyboard screen will display. If house numbers are available, but not the one that you require, you may have to choose the same street in a neighbouring area. Go to step 4. If the House Number option is not displayed at all, house numbers are not available for your selected section of the street. Tap Go to Centre of Street to display the Destination Preview screen. Go to step c. b) Use the Keyboard screen to search for the house number of your destination. The Destination Preview screen will display. c) Complete one of the following: Please ensure that the route preferences are applicable for the route that you have specified, before you tap Go. If you want to ... calculate the route and open the 3D Map screen select a more precise location by pointing display the geographical details save the destination as My Home Then ... tap Go. Your route is calculated; the 3D Map screen will display. tap the map to switch to the main map view. tap Details. The Destination Details screen will display. tap Save. The New Favourite screen will display. Tap Save as Home. save the destination as a Favourite tap Save. The New Favourite screen will display. Tap Save as Favourite. 28 iCN 700 series | How do I go from A to B? If you want to ... display Route Preferences change your destination Then ... tap Preferences. The Route Calculation screen will display. . press The Destination Search screen will display. 29 iCN 700 series | How do I go from A to B? How do I create a trip with multiple stops? You can use the Multi-stop Trip Planner screen to set multiple waypoints for your trip. Your route will be calculated to go via each of these points in the specified order. Waypoints can be added via the Multi-stop Trip Planner screen or by selecting Location from the pop-up Map menu on the 2D Map or 3D Map screen, then Add to Trip. You can save up to 200 multi-stop trips, each with up to 15 waypoints. Waypoints added, updated or deleted after a multi-stop trip has commenced will not affect the current route. Quick Steps 1. 2. 3. 4. 5. 6. Start your Multi-stop Trip Select the country Search for the city/area Search for the street Search for the house number Tap Go. 30 iCN 700 series | How do I go from A to B? Case Study: How do I navigate to multiple addresses? This case study will show you how to set a multi-stop trip by selecting your country, then area, then street, then house number for each waypoint. 1. Start your multi-stop trip The Multi-stop Trip Planner screen will display. a) Tap Add. The Add to Trip Menu will display. b) Tap Address or POI. The Destination Search screen will open. You can also add waypoints using Favourites, recent destinations and nearest Points of Interest. 31 iCN 700 series | How do I go from A to B? 2. Select the country If you only have the map of one country installed and selected, that country is selected for your destination by default and cannot be changed. Go to step 3. a) From the Destination Search screen, tap Change Country. The Select Country screen will display. Select a country from the list. The Destination Search screen will display. 3. Search for the city/area a) From the Destination Search screen, tap City/Area. The Keyboard screen will display. b) Use the Keyboard screen to search for the city or area of your destination. The Destination Search screen will display. 32 iCN 700 series | How do I go from A to B? 4. Search for the street a) From the Destination Search screen, tap Street. The Keyboard screen will display. b) Use the Keyboard screen to search for the street of your destination. The Destination Search screen will display. If house numbers and intersection information are not available for your selected street, the Waypoint Preview screen will display. Go to step 5b. 5. Search for the house number a) From the Destination Search screen, tap House Number. The Keyboard screen will display. If the House Number option is not displayed, house numbers are not available for your selected street. To display the Destination Preview screen, tap Go to centre of street. Go to step c. 33 iCN 700 series | How do I go from A to B? b) Use the Keyboard screen to search for the house number of your destination. The Waypoint Preview screen will display. c) Tap Add. The destination is automatically saved and the Multi-Stop-Trip Planner screen will display. d) Complete one or more of the following: If you want to ... add another waypoint Waypoints added after a multi-stop trip has commenced will not be included in the current route. Then ... tap Add. The Destination Search screen will display. Return to step 3. calculate the route tap Go. The Multi Stop Trip Preview screen will display. Tap Go. The Map screen will display the calculated route. tap a destination point to move. The Waypoint Preview screen will display. Tap Move up or Move down. The Multi-stop Trip Planner screen will display. tap a destination point. The Waypoint Preview screen will display. Tap Details. The Waypoint Details screen will display. tap Clear. tap a destination point to delete. The Waypoint Preview screen will display. Tap Delete. The Multi-stop Trip Planner screen will display. change the order of your waypoints display the geographical details of a waypoint delete all waypoints delete one waypoint 34 iCN 700 series | How do I go from A to B? If you want to ... save the multi-stop trip as a Favourite Then ... tap Save. The New Favourite screen will display. Tap Save as Favourite. The Favourite will save and the Multi-Stop Trip Planner screen will display. How do I skip a waypoint during a multistop trip? You can modify a multi-stop trip at any time from the Multi-stop Trip Planner screen, however if you have already commenced a trip, changes will not affect the current route: To skip a waypoint during a multi-stop trip, complete the following: 1. 2. Tap the map to display the cross-hairs. The Map Menu will display. Tap Route, then Skip Waypoint. The next waypoint will be skipped and the route recalculated to the following waypoint. 35 iCN 700 series | How do I go from A to B? How do I search for a landmark or venue? Setting a Point of Interest (POI) as your destination A POI is a named site, feature, landmark or public venue which can be displayed as an icon on the map. POIs are grouped by type, such as petrol stations, parks and museums. How do I find the nearest petrol station? You can press to quickly find the nearest petrol station. As POIs are grouped by category, including petrol stations, your iCN will display a list of the nearest petrol stations based upon your current location. a) . Press The Select POI screen will display, showing a list of the nearest petrol stations based upon your current location. The nearest appears at the top of the list. b) Select a petrol station from the list. The Destination Preview screen will display. c) Tap Go. Your route is calculated; the 3D Map screen will display. 36 iCN 700 series | How do I go from A to B? How do I find the nearest parking area? You can press to quickly find the nearest parking area. This case study will show you how to set your destination by locating and selecting a parking area Point of Interest (POI). As POIs are grouped by category, including parking areas, the iCN will show you a list of the nearest parking areas based upon your current location. a) Press . The Select POI screen will display, showing a list of the nearest parking areas based upon your current location. The nearest appears at the top of the list. b) Select a parking area from the list. The Destination Preview screen will display. c) Tap Go. Your route is calculated; the 3D Map screen will display. 37 iCN 700 series | How do I go from A to B? How do I search for other POIs? Select a POI destination using the Destination Search, Keyboard and Destination Preview screens, which used together form a POI-entry wizard. This section describes how to use each of these screens and provides a case study to help guide you through setting your POI. Quick Steps 1. 2. 3. 4. Open the Destination Search screen Select the country Select the type of POI Tap Go. Case Study: How do I search for a Point of Interest? This case study will show you how to set your destination by selecting a Point of Interest (POI). 1. Open the Destination Search screen The Destination Search screen will display. If this is the first time you are setting your destination and you have maps from more than one country installed and selected, then the Select Country screen will display instead of the Destination Search screen. Go directly to step 2b. The next time you perform this procedure, the Destination Search screen will open as expected. 38 iCN 700 series | How do I go from A to B? 2. Select the country If you only have the map of one country installed and selected, that country is selected for your destination by default and cannot be changed. Go to step 3. a) From the Destination Search screen, tap Change Country. The Select Country screen will display. Select a country from the list. The Destination Search screen will display. 3. Select the type of POI To narrow the search for a type of POI, you can first search by Area. a) From the Destination screen, tap Point of Interest. The Select POI screen will display. b) Select a POI type from the list. The Keyboard screen will display. 39 iCN 700 series | How do I go from A to B? c) Use the Keyboard screen to find the POI. The Destination Preview screen will display. d) Complete one of the following: Please ensure that the route preferences are applicable for the route that you have specified, before you tap Go. If you want to ... calculate the route and open the 3D Map screen select a more precise location by pointing display the geographical details save the destination as My Home Then ... tap Go. Your route is calculated; the 3D Map screen will display. tap the map to switch to the main map view. tap Details. The Destination Details screen will display. tap Save. The New Favourite screen will display. Tap Save as Home. save the destination as a Favourite tap Save. The New Favourite screen will display. Tap Save as Favourite. display Route Preferences change your destination tap Preferences. The Route Calculation screen will display. . press The Destination Search screen will display. 40 iCN 700 series | How do I view my route? How do I view my route? Once a route has been calculated, the 3D Map screen will display. You will be directed to your destination by vocal and visual instructions. You can view your route in several ways by pressing to cycle through the map screens. In this section 3D Map screen .................................................................................................................................... 42 2D Map screen .................................................................................................................................... 44 Next Turn screen ................................................................................................................................. 46 Direction List screen ............................................................................................................................ 47 41 iCN 700 series | How do I view my route? 3D Map screen The 3D Map screen is oriented to your travelling direction. To view the 3D Map screen when a route has been calculated, press Tap and drag the screen, to move across the map. Tap and hold the map, to view Map menu. For more information, see "How do I use the Map Menu?" on page 69. to cycle through the screens. Item Direction of next turn Description The direction of your next turn. To repeat the voice prompt of your next turn, tap the turn arrow. Distance to next turn Next instruction The distance to your next turn. The direction and name of the street to turn in to. When you cycle through the Information options, a function description will display briefly at the top of the screen. Next turn arrow Your next turn is highlighted in a different colour from future turns. The default colour of your next turn is green, but will depend on the colour theme you are using. Current position Status bar Your current position is marked with Displays one of the following: . The name of the street you are located on Speed warnings Active POIs. 42 iCN 700 series | How do I view my route? Item Information Description Displays one of the following options: Time km/h or mph (Speed) TTG (Time to Go) DTG (Distance to Go) ETA (Estimated Time of Arrival). Tap to cycle through the options. During a Multi-trip journey, Time to Go, Distance to Go and ETA will display as: Time to Waypoint, Distance to Waypoint and ETA at Waypoint. Route Cancel route Zoom Your current route is highlighted. Cancels your current route To view zoom options, tap . or scroll To display a smaller area in greater detail, tap down. To display a larger area in less detail, tap Compass and GPS information Displays one of the following options: or scroll up. Green Quadrants - A valid GPS signal is being used to fix your position; displays between one and four quadrants to indicate the strength of the signal. Red Circle - No GPS signal. Compass heading. Tap to cycle through the options; tap and hold to display the GPS Status screen. 43 iCN 700 series | How do I view my route? 2D Map screen The 2D Map screen shows your current position (if a GPS fix is active) and surrounding street names. If a route has been calculated, the route and turns are highlighted. The 2D Map screen is displayed Course Up, unless the Map Display preferences are set to North. To view the 2D Map screen, press to cycle through the screens. Tap and drag the screen, to move across the map. Tap and hold the map, to view Map menu. For more information, see "How do I use the Map Menu?" on page 69. Item Direction of next turn Description The direction of your next turn. To repeat the voice prompt of your next turn, tap the turn arrow. Distance to next turn Next instruction The distance to your next turn. The direction and name of the street to turn in to. When you cycle through the Information options, a function description will display briefly at the top of the screen. Current position Scale bar Status bar Your current position is marked with Displays map scale. Displays one of the following: . The name of the street you are located on Speed warnings Active POIs. 44 iCN 700 series | How do I view my route? Item Information Description Displays one of the following options: Time km/h or mph (Speed) TTG (Time to Go) DTG (Distance to Go) ETA (Estimated Time of Arrival). Tap to cycle through the options. During a Multi-trip journey, Time to Go, Distance to Go and ETA will appear as: Time to Waypoint, Distance to Waypoint and ETA at Waypoint. Route Cancel route Next turn arrow Your current route is highlighted. Cancels your current route. Your next turn is highlighted in a different colour to future turns. The default colour of your next turn is green, but will depend on the colour theme you are using. Zoom To view zoom options, tap . or scroll To display a smaller area in greater detail, tap down. To display a larger area in less detail, tap Compass and GPS Information Displays one of the following options: or scroll up. Green Quadrants - A valid GPS signal is being used to fix your position; displays between one and four quadrants to indicate the strength of the signal. Red Circle - No signal. Compass heading. Tap to cycle through the options; tap and hold to display the GPS Status screen. 45 iCN 700 series | How do I view my route? Next Turn screen The Next Turn screen displays information that you need for the next turn, the direction of the turn and the distance to the turn. A route must first have been calculated, for this screen to be available. To view the Next Turn screen when a route has been calculated, press to cycle through the screens. Item Next instruction Description The direction and name of the street to turn in to. When you cycle through the Information options, a function description will display briefly at the top of the screen. Direction of next turn Scale bar Distance to next turn Status Bar The direction of your next turn. Displays map scale. The distance to your next turn. Displays one of the following: The name of the street you are located on Speed warnings Active POIs. Information Displays one of the following options: Time km/h or mph (Speed) TTG (Time to Go) DTG (Distance to Go) ETA (Estimated Time of Arrival). Tap to cycle through the options. During a Multi-trip journey, Time to Go, Distance to Go and ETA will appear as: Time to Waypoint, Distance to Waypoint and ETA at Waypoint. Cancel Route Cancels your current route. 46 iCN 700 series | How do I view my route? Item Map of next turn Current position Compass and GPS Information Description A map of your next turn. Your current position is marked with Displays one of the following options: Green Quadrants - A valid GPS signal is being used to fix your position; displays between one and four quadrants to indicate the strength of the signal. Red Circle - No signal. Compass heading. Tap to cycle through the options; tap and hold to display the GPS Status screen. ; if visible. Direction List screen The Direction List screen displays the next four turns of your route, the turn direction, the street name and the distance to the turn. You can view all the turns in the list, using the scroll bar. A route must first have been calculated for this screen to be available. To view the Direction List screen when a route has been calculated, press to cycle through the screens. Item Direction of turn Distance to turn Instruction Next turn (highlighted) Upcoming turns