User manual NEC 42RESI

Operation Manual For the specifications of your plasma monitor, refer to "Model Information". NEC Solutions (America), Inc. Important Information Precautions Please read this manual carefully before using your plasma monitor and keep the manual handy for future reference. 2. Do not use this unit's polarized plug with extension cords or outlets unless the prongs can be completely inserted. 3. Do not expose the unit to water or moisture. 4. Avoid damage to the power cord, and do not attempt to modify the power cord. 5. Unplug the power cord during electrical storms or if the unit will not be used over a long period. 6. Do not open the cabinet which has potentially dangerous high voltage components inside. If the unit is damaged in this way the warranty will be void. Moreover, there is a serious risk of electric shock. 7. Do not attempt to service or repair the unit. The manufacturer is not liable for any bodily harm or damage caused if unqualified persons attempt service or open the back cover. Refer all service to authorized Service Centers. To avoid damage and prolong operating life: 1. Use only with 100-240V 50/60Hz AC power supply. Continued operation at line voltages greater than 100240 Volts AC will shorten the life of the unit, and might even cause a fire hazard. 2. Handle the unit carefully when installing it and do not drop. 3. Set the unit away from heat, excessive dust, and direct sunlight. 4. Protect the inside of the unit from liquids and small metal objects. In case of accident, unplug the power cord and have it serviced by an authorized Service Center. 5. Do not hit or scratch the panel surface as this causes flaws on the surface of the screen. 6. For correct installation and mounting it is strongly recommended to use a trained, authorized dealer. 7. As is the case with any phosphor-based display (like a CRT monitor, for example) light output will gradually decrease over the life of a Plasma Display Panel. 8. To avoid sulfurization it is strongly recommended not to place the unit in a dressing room in a public bath or hot spring bath. 9. Do not use in a moving vehicle, as the unit could drop or topple over and cause injuries. 10. Do not place the unit on its side, upside-down or with the screen facing up or down, to avoid combustion or electric shock. Plasma monitor cleaning procedure: 1. Use a soft dry cloth to clean the front panel and bezel area. Never use solvents such as alcohol or thinner to clean these surfaces. 2. Clean plasma ventilation areas with a vacuum cleaner with a soft brush nozzle attachment. 3. To ensure proper ventilation, cleaning of the ventilation areas must be carried out monthly. More frequent cleaning may be necessary depending on the environment in which the plasma monitor is installed. Recommendations to avoid or minimize phosphor burn-in: Like all phosphor-based display devices and all other gas plasma displays, plasma monitors can be susceptible to phosphor burn under certain circumstances. Certain operating conditions, such as the continuous display of a static image over a prolonged period of time, can result in phosphor burn if proper precautions are not taken. To protect CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION:TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol warns the user that uninsulated voltage within the unit may have sufficient magnitude to cause electric shock. Therefore, it is dangerous to make any kind of contact with any part inside of this unit. This symbol alerts the user that important literature concerning the operation and maintenance of this unit has been included. Therefore, it should be read carefully in order to avoid any problems. WARNING TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO DO NOT USE THIS UNIT'S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS, UNLESS THE PRONGS CAN BE FULLY INSERTED. REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH-VOLTAGE COMPONENTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. Warnings and Safety Precaution This plasma monitor is designed and manufactured to provide long, trouble-free service. No maintenance other than cleaning is required. Please see the section "Plasma monitor cleaning procedure" on the next page. The plasma display panel consists of fine picture elements (cells) with more than 99.99 percent active cells. There may be some cells that do not produce light or remain lit. For operating safety and to avoid damage to the unit, read carefully and observe the following instructions. To avoid shock and fire hazards: 1. Provide adequate space for ventilation to avoid internal heat build-up. Do not cover rear vents or install the unit in a closed cabinet or shelves. If you install the unit in an enclosure, make sure there is adequate space at the top of the unit to allow hot air to rise and escape. If the monitor becomes too hot, the overheat protector will be activated and the monitor will be turned off. If this happens, turn off the power to the monitor and unplug the power cord. If the room where the monitor is installed is particularly hot, move the monitor to a cooler location, and wait for 60 minutes to cool the monitor. If the problem persists, contact your dealer for service. 2 your investment in this plasma monitor, please adhere to the following guidelines and recommendations for minimizing the occurrence of image burn: * Always enable and use your computer's screen saver function during use with a computer input source. * Display a moving image whenever possible. * Change the position of the menu display from time to time. * Always power down the monitor when you are finished using it. If the plasma monitor is in long term use or continuous operation take the following measures to reduce the likelihood of phosphor burn: * Lower the Brightness and Contrast levels as much as possible without impairing image readability. * Display an image with many colors and color gradations (i.e. photographic or photo-realistic images). * Create image content with minimal contrast between light and dark areas, for example white characters on black backgrounds. Use complementary or pastel color whenever possible. * Avoid displaying images with few colors and distinct, sharply defined borders between colors. * Note: Burn-in is not covered by the warranty. Contact your dealer for other recommended procedures that will best suit your particular application needs. Recommandations importantes Précautions Veuillez lire avec attention ce manuel avant d'utiliser le moniteur à plasma et le conserver accessible pour s'y référer ultérieurement. Mises en garde et précautions de sécurité Ce moniteur à plasma a été conçu et fabriqué pour une utilisation fiable et durable. Il ne nécessite aucun entretien en dehors du nettoyage. Voir la section "Méthode de nettoyage du moniteur à plasma" plus loin. Le panneau à affichage plasma est constitué de fines particules d'images (cellules) dont plus de 99,99%sont actives. Certaines d'entre elles ne produisent pas de lumière ou restent allumées. Pour des raisons de sécurité et pour éviter d'endommager l'appareil, lire attentivement les instructions suivantes. Pour éviter les risques d'éléctrocution et d'incendie: 1. Laisser suffisament d'espace autour de l'appareil pour la ventilation et éviter toute augmentation excessive de la température interne. Ne pas couvrir les évents ou l'installer dans un endroit trop exigu. Si vous installez l'appareil dans un espace clos, assurezvous qu'il y ait suffisamment d'espace au dessus pour permettre à l'air chaud de s'élever et de s'évacuer. Si la température du moniteur devient excessive, la protection contre les surchauffes entrera en action et coupera l'alimentation. Dans ce cas, éteindre l'appareil et débrancher le câble d'alimentation. Si la température de la pièce dans laquelle se trouve le moniteur est particulièrement élevée, déplacer celui-ci dans un endroit plus frais et attendre environ 60 minutes qu'il refroidisse. Si le problème persiste, prendre contact avec votre revendeur. 2. Ne pas raccorder la prise d'alimentation polarisée de ce périphérique à une rallonge ou une prise murale si les fiches ne peuvent pas être complètement insérées. 3. Ne pas exposer à L'eau ou à l'humidité. 4. Eviter d'endommager le cordon d'alimentation, et ne pas modifier le cordon d'alimentation. 5. Débrancher le câble d'alimentation électrique pendant les orages ou les longues périodes d'inactivité. 6. Ne pas ouvrir le coffret. Des composants de haute tension se trouvent à l'intérieur. Si l'appareil est endommagé de cette manière, la garantie devient caduque. De plus, il y a risque d'électrocution. 3 7. Ne pas essayer d'intervenir ou de réparer l'appareil. Le ATTENTION RISQUE D'ELECTROCUTION NE PAS OUVRIR MISE EN GARDE: AFIN DE REDUIRE LES RISQUES D'ELECTRO-CUTION, NE PAS DEPOSER LE COUVERCLE, IL N'Y A AUCUNE PIECE UTILISABLE A L'INTERIEUR DE CET APPAREIL. NE CONFIER LES TRAVAUX D'ENTRETIEN QU'A UN PERSONNEL QUALIFIE. Ce symbole a pour but de prévenir l'utilisateur de la présence d'une tension dangereuse, non isolée se trouvant à l'intérieur de l'appareil. Elle est d'une intensité suffisante pour constituer un risque d'électrocution. Eviter le contact avec les pièces à l'intérieur de cet appareil. Ce symbole a pour but de prévenir l'utilisateur de la présence d'importantes instructions concernant l'entretien et le fonctionnement de cet appareil. Par conséquent, elles doivent être lues attentivement afin d'éviter des problèmes. AVERTISSEMENT AFIN DE REDUIRE LES RISQUES D'INCENDIE OU D'ELECTROCUTION, NE PAS EXPOSER CET APPAREIL A LA PLUIE OU A L'HUMIDITE. AUSSI, NE PAS UTILISER LA FICHE POLARISEE AVEC UN PROLONGATEUR OU UNE AUTRE PRISE DE COURANT SAUF SI CES LAMES PEUVENT ETRE INSEREES A FOND. NE PAS OUVRIR LE COFFRET, DES COMPOSANTS HAUTE TENSION SE TROUVENT A L'INTERIEUR. LAISSER A UN PERSONNEL QUALIFIE LE SOIN DE REPARER CET APPAREIL. fabricant décline toute responsabilité en cas de blessure corporelle ou de dégâts matériels résultant d'une opération d'entretien quelconque effectuée par des personnes non qualifiées ou résultant de l'ouverture du couvercle arrière. S'adresser aux services après-vente autorisés. Pour éviter des dommages et prolonger la durée de service de l'appareil: 1. N'utiliser qu'une source d'alimentation de 100-240 V 50/60 Hz CA. Le fait d'utiliser l'appareil en continu à des tensions de ligne supérieures à 100-240 Volts CA réduit sa durée de vie et risque de provoquer un incendie. 2. Manipuler l'appareil avec soin pendant son déplacement et ne pas le faire tomber. 3. Eloigner l'appareil des endroits chauds, très poussiéreux et exposés en plein soleil. 4. Eviter que des liquides et des petits objets métalliques pénètrent à l'intérieur de l'appareil. En cas d'incident de ce genre, débrancher le câble d'alimentation électrique et confier le moniteur à un service après-vente agréé. 5. Ne pas frapper ou rayer la surface de la écran plasma, car des défauts risquent de se produire sur la surface de la écran plasma. 6. Pour un montage et une installation correcte, il est fortement recommandé de faire appel à un revendeur agréé et qualifié. 7. Comme c'est le cas pour tout affichage à base de phosphore (comme un moniteur CRT, par exemple), la puissance de lumière baisse graduellement au cours de la vie du Panneau d'Affichage à Plasma. 8. Pour éviter tout risque de sulfuration, il est fortement conseillé de ne pas installer l'appareil dans un vestiaire, un bain public ou un bain de source thermale. 9. Ne pas utiliser dans un véhicule en marche car l'unité pourrait tomber ou glisser et provoquer des blessures. 10. Pour éviter l `inflammation ou les chocs électriques, ne pas placer l'unité sur la tranche, à l'envers ou avec l'écran vers le bas ou vers le haut. Méthode de nettoyage du moniteur à plasma: 1. Nettoyer le panneau avant et le cadre en procédant à l'aide d'un chiffon doux et sec. Ne jamais utiliser de solvents du type alcool ou diluant pour le nettoyage de ces surfaces. 2. Nettoyer les prises d'aération du plasma en procédant à l'aide d'une brosse à poils doux fixée à un aspirateur. 3. Pour garantir la bonne ventilation du moniteur, nettoyer les prises d'air tous les mois. Un nettoyage plus fréquent peut s'avérer nécessaire selon les conditions environnantes dans lesquelles le moniteur à plasma est utilisé. Pour éviter les risques de brûlage du luminophore, les mesures suivantes sont recommandées: Comme tous les périphériques d'affichage à base luminophore et tous les autres affichages gaz plasma, les moniteurs plasma peuvent être sujets au brûlage du luminophore dans certaines circonstances. Certaines conditions d'utilisation, telles que l'affichage continu d'une image statique pour une durée prolongée, peuvent causer le brûlage du luminophore si aucune précaution n'est prise. Pour protéger votre investissement dans ce moniteur à plasma, veuillez suivre les directives et les conseils suivantes pour minimiser l'occurence le marquage de l'écran: 4 · Assurez-vous de mettre en marche et d'utliser l'économisateur d'écran chaque fois que c'est possible lorsque vous l'utilisez avec une source d'entrée d'ordinateur. · Affichez une image en mouvement aussi souvent que possible. · Changer la position de l'affichage de menu de temps à autre. · Coupez toujours l'alimentation lorsque vous avez terminé d'utiliser la moniteur. Si le moniteur est en usage continu ou longue durée, prenez les mesures suivantes afin d'éviter l'occurence le brûlage du luminophore: · Abaissez le niveau de l'image (contraste, luminosité) autant que possible, sans faire perdre la lisibilité de l'image. · Affichez une image avec de nombreuses couleurs et graduations de couleur (par ex. des images photographiques ou photo-réalistes). · Créez un contenu d'image avec un contraste minimal entre les zones sombres et les zones claires, par exemple, des caractères blancs sur un fond noir. Utilisez des couleurs complémentaires ou pastels le plus souvent possible. · Évitez d'afficher des images avec peu de couleurs et des limites nettes et clairement définies entre les couleurs. * Remarque: Le brûlage de l'écran n'est pas couvert par la garantie. Contactez un revendeur agréé ou un revendeur de marque pour d'autres procédures qui conviendront le mieux à vos besoins particuliers. Contents Installation ...................................................... 6 Ventilation Requirements for enclosure mounting .......... 6 How to use the safety metal fittings and the screws for safety metal fittings ................................................ 6 Cable Management .................................................. 7 How to use the remote control .................................... 7 Battery Installation and Replacement ........................... 7 Operating Range .......................................................... 7 Handling the remote control ......................................... 7 Function Settings Menu ........................................... 24 Setting the power management for computer images ..... 24 POWER/STANDBY indicator ................................... 24 Setting the Input Skip ................................................. 24 Reducing burn-in of the screen .................................. 24 Setting Closed Caption .............................................. 26 Reducing the brightness of Closed Caption ................ 26 Signal Information Menu ......................................... 26 Checking the frequencies, polarities of input signals, and resolution .......................................................... 26 Part Names and Function .................................. 8 Front View .............................................................. 8 Rear View/ Terminal Board ....................................... 9 Remote Control ...................................................... 10 External Control ............................................. 27 Application ........................................................... 27 Connections .......................................................... 27 Type of connector: D-Sub 9-pin male ........................ 27 Communication Parameters ..................................... 27 External Control Codes (Reference) .......................... 27 Basic Operations ............................................. 11 POWER ................................................................ 11 To turn the unit ON and OFF: .................................... 11 VOLUME .............................................................. 11 To adjust the sound volume: ....................................... 11 MUTE ................................................................... 11 To mute the audio: ..................................................... 11 DISPLAY ................................................................ 11 To check the settings: ................................................. 11 DIGITAL ZOOM ..................................................... 11 OFF TIMER ............................................................ 11 To set the off timer: .................................................... 11 To check the remaining time: ..................................... 11 To cancel the off timer: .............................................. 11 Pin Assignments ............................................. 27 mini D-Sub 15-pin connector (Analog) ..................... 27 DVI-D 24-pin connector (Digital) .............................. 27 Troubleshooting .............................................. 28 Contents of the Package Plasma monitor Power cord Remote control with two AAA Batteries Manuals (Model Information and Operation) Safety metal fittings Ferrite cores, bands Cable clamps HDMI-DVI cable * These are fittings for fastening the unit to a wall to prevent tipping due to external shock when using the stand (optional). Fasten the safety fittings to the holes in the back of the monitor using the safety fitting mount screws (see page 6). WIDE Operations ............................................. 12 Wide Screen Operation (manual) ............................ 12 When viewing videos or digital video discs ............... 12 Wide Screen Operation with Computer Signals ......... 13 OSM (On Screen Menu) Controls ....................... 14 Menu Operations ................................................... 14 Menu Tree ............................................................. 15 Picture Settings Menu .............................................. 17 Storing picture settings ............................................... 17 Adjusting the picture .................................................. 17 Reducing noise in the picture ..................................... 17 Setting the color temperature ..................................... 18 Adjusting the color to the desired level ...................... 18 Changing the Gamma Curve ...................................... 18 Making the Low Tone adjustments ............................ 18 Adjusting the pedestal level (black level) ................... 19 Adjusting the colors ................................................... 19 Setting the picture to suit the movie ........................... 19 Setting the picture mode according to the brightness of the room .............................................................. 19 Audio Settings Menu .............................................. 20 Adjusting the treble, bass and left/right balance and audio input select ..................................................... 20 Setting the allocation of the audio connectors ............ 20 Image Adjust Settings Menu .................................... 20 Adjusting the Position, Size, Fine Picture, Picture Adj ..... 20 SET UP Settings Menu ............................................. 21 Setting the language for the menus ............................. 21 Setting the BNC connectors ....................................... 21 Checking the signal being transmitted to RGB1 terminal .... 21 Setting high definition images to the suitable screen size .... 21 Setting a computer image to the correct RGB select screen ...................................................................... 21 Setting the signal and black level for DVI signal ........ 22 Setting the video signal format ................................... 22 Setting the background color when no signal is being input ........................................................................ 22 Setting the gray level for the sides of the screen ......... 23 Setting the screen size for S1/S2 video input .............. 23 Turning on/off the menu display ................................ 23 Setting the position of the menu ................................. 23 Resetting to the default values .................................... 23 Options · Wall mount unit · Ceiling mount unit · Tilt mount unit · Stand · Attachable speakers 5 Installation You can attach your optional mounts or stand to the plasma monitor in one of the following two ways: * While it is upright. (See Drawing A) * As it is laid down with the screen face down (See Drawing B). Lay the protective sheet, which was wrapped around the monitor when it was packaged, beneath the screen surface so as not to scratch the screen face. * Do not touch or hold the screen face when carrying the unit. · This device cannot be installed on its own. Be sure to use a stand or original mounting unit. (Wall mount unit, Stand, etc.) * See page 5. · For correct installation and mounting it is strongly recommended to use a trained, authorized dealer. Failure to follow correct mounting procedures could result in damage to the equipment or injury to the installer. Product warranty does not cover damage caused by improper installation. * Use only the mounting kit or stand provided by manufacturer and listed under Options. Drawing A Drawing B Ventilation Requirements for enclosure mounting To allow heat to disperse, leave space between surrounding objects as shown on the diagram below when installing. How to use the safety metal fittings and the screws for safety metal fittings These are fittings for fastening the unit to a wall to prevent tipping due to external shock when using the stand (optional). Fasten the safety fittings to the holes in the back of the monitor using the safety fitting mount screws. Screw hole Wall 50mm (2") 50mm (2") 50mm (2") Wall Screw or Hook etc. (Not supplied) Safty metal fittings Screw for Safty metal fittings Metal chain (Not supplied) 50mm (2") 50mm (2") Wall Table Top 6 Cable Management Using the cable clamps provided with the plasma display, bundle at the back of the unit the signal and audio cables connected to the display. Back of the unit Operating Range * Use the remote control within a distance of about 7 m/ 23ft. from the front of the monitor's remote control sensor and at horizontal and vertical angles of up to approximately 30°. * The remote control operation may not function if the monitor's remote control sensor is exposed to direct sunlight or strong artificial light, or if there is an obstacle between the sensor and the remote control. mounting hooks To attach 1. clamp 2. Approx. 7m / 23ft mounting hook cables To detach How to use the remote control Battery Installation and Replacement Insert the 2 "AAA" batteries, making sure to set them in with the proper polarity. 1.Press and open the cover. Handling the remote control · Do not drop or mishandle the remote control. · Do not get the remote control wet. If the remote control gets wet, wipe it dry immediately. · Avoid heat and humidity. · When not using the remote control for a long period, remove the batteries. · Do not use new and old batteries together, or use different types together. · Do not take apart the batteries, heat them, or throw them into a fire. 2.Align the batteries according to the (+) and (­) indication inside the case. 3.Replace the cover. 7 Part Names and Function Front View MENU/ENTER VOLUME DOWN UP LEFT/- RIGHT/+ INPUT SELECT /EXIT MENU/ENTER VOLUME DOWN UP LEFT/ - RIGHT/+ INPUT SELECT /EXIT 7 6 5 4 1 3 2 q Power Turns the monitor's power on and off. w Remote sensor window Receives the signals from the remote control. e POWER/STANDBY indicator When the power is on ............................. Lights green. When the power is in the standby mode ... Lights red. r INPUT SELECT / EXIT Switches the input. The available inputs depend on the setting of "BNC INPUT", "RGB SELECT" and "DVI SET UP". Functions as the EXIT buttons in the On-Screen Menu (OSM) mode. t LEFT/­ and RIGHT/+ Enlarges or reduces the image. Functions as the CURSOR ( / ) buttons in the On-Screen Menu (OSM) mode. y VOLUME DOWN and UP Adjusts the volume. Functions as the CURSOR (v/ w) buttons in the On-Screen Menu (OSM) mode. u MENU/ENTER Sets the On-Screen Menu (OSM) mode and displays the main menu. WARNING The Power on/off switch does not disconnect the plasma display completely from the supply mains. 8 Rear View/ Terminal Board C D E F G H AB I A AC IN Connect the included power cord here. B EXT SPEAKER L and R Connect speakers (optional) here. Maintain the correct polarity. Connect the (positive) speaker wire to the EXT SPEAKER terminal and the (negative) speaker wire to the EXT SPEAKER terminal on both LEFT and RIGHT channels. Please refer to your speaker's owner's manual. C VIDEO1, 2, 3 (BNC, RCA, S-Video) Connect VCR's, DVD's or Video Cameras, etc. here. D AUDIO1, AUDIO2, AUDIO3 These are audio input terminals. The input is selectable. Set which video image to allot them from the audio menu screen. E DVD1 / HD1 Connect DVD's, High Definition or Laser Discs, etc. here. F DVD2/ HD2, RGB2 DVD2/ HD2: You can connect DVDs, High Definition sources, Laser Discs, etc. here. This input can be set for use with an RGB or component source. (see page 21) RGB2: You can connect an analog RGB signal and the syncronization signal. G RGB1 (D-Sub) Connect an analog RGB signal from a computer, etc. here. H DVD3/HD3, RGB3 (DVI) Connect a digital signal (TMDS) from a source with a DVI output. This input can be set for use with an RGB3 or DVD3/ HD3 source. (see page 22) I EXTERNAL CONTROL (D-Sub) This terminal is used when operating and controlling the monitor externally (by external control). 9 Remote Control i MUTE Mutes the audio. o VOLUME (+ /­) Adjusts the audio volume. !0 ZOOM (+ /­) Enlarges or reduces the image. !1 CONTRAST Press this button to adjust contrast directly. !2 BRIGHTNESS Press this button to adjust brightness directly. !3 PICTURE MODE Press this button to adjust picture mode directly. !4 COLOR TEMP Press this button to adjust color tone directly. !5 VIDEO1, 2, 3 Press this button to select VIDEO as the source. VIDEO can also be selected using the INPUT SELECT button on the monitor. !6 DVD/HD1, 2, 3 Press this button to select DVD/HD as the source. DVD/HD can also be selected using the INPUT SELECT button on the monitor. !7 PC/RGB Press this button to select PC/RGB as the source. PC/RGB can also be selected using the INPUT SELECT button on the monitor. !8 PICTURE MEMORY Switches sequentially between picture memory settings 1 to 6. !9 Remote control signal transmitter Transmits the remote control signals. q POWER ON/STANDBY Switches the power on/standby. (This does not operate when POWER/STANDBY indicator of the main unit is off.) w OFF TIMER Activates the off timer for the unit. e DISPLAY Displays the source settings on the screen. r WIDE Automatically detects the signal and sets the aspect ratio. Wide button is not active for all signals. t MENU/ENTER Press this button to access the OSM controls. Press this button during the display of the main menu to go to the sub menu. y CURSOR (v / w / / ) Use these buttons to select items or settings and to adjust settings or switch the display patterns. u EXIT Press this button to exit the OSM controls in the main menu. Press this button during the display of the sub menu to return to the previous menu. 10 Basic Operations POWER To turn the unit ON and OFF: 1. Plug the power cord into an active AC power outlet. 2. Press the Power button (on the unit). The monitor's POWER/STANDBY indicator turns red and the standby mode is set. 3. Press the POWER ON button (on the remote control) to turn on the unit. The monitor's POWER/STANDBY indicator will light up (green) when the unit is on. 4. Press the POWER STANDBY button (on the remote control) or the Power button (on the unit) to turn off the unit. The monitor's POWER/STANDBY indicator turns red and the standby mode is set (only when turning off the unit with the remote control). OFF TIMER To set the off timer: The off timer can be set to turn the power off after 30, 60, 90 or 120 minutes. 1. Press the OFF TIMER button to start the timer at 30 minutes. 2. Press the OFF TIMER button to the desired time. 3. The timer starts when the menu turns off. 30 60 90 120 0 OFF TIMER 30 VOLUME To adjust the sound volume: 1. Press and hold the VOLUME button (on the remote control or the unit) to increase to the desired level. button (on the remote 2. Press and hold the VOLUME control or the unit) to decrease to the desired level. To check the remaining time: 1. Once the off timer has been set, press the OFF TIMER button once. 2. The remaining time is displayed, then turns off after a few seconds. 3. When five minutes remain the remaining time appears until it reaches zero. OFF TIMER 28 MUTE To mute the audio: Press the MUTE button on the remote control to mute the audio; press again to restore. DISPLAY To check the settings: 1. The screen changes each time the DISPLAY button is pressed. 2. If the button is not pressed for approximately three seconds, the menu turns off. DIGITAL ZOOM Digital zoom specifies the picture position and enlarges the picture. 1. Press the ZOOM (+ or -) button to display magnifying ) glass. ( To change the size of the picture: Press the ZOOM+ button and enlarge the picture. A press of the ZOOM- button will reduce the picture and return it to its original size. To change the picture position: Select the position with the vw buttons. 2. Press the EXIT button to delete the pointer. To cancel the off timer: 1. Press the OFF TIMER button twice in a row. 2. The off timer is canceled. OFF TIMER 0 Note: After the power is turned off with the off timer ... A slight current is still supplied to the monitor. When you are leaving the room or do not plan to use the system for a long period of time, turn off the power of the monitor. 11 WIDE Operations Wide Screen Operation (manual) With this function, you can select one of six screen sizes. 2.35:1 size screen When viewing videos or digital video discs 1. Press the WIDE button on the remote control. 2. Within 3 seconds ... Press the WIDE button again. The screen size switches as follows: NORMAL ANAMORPHIC STADIUM ZOOM 2.35:1 14:9 Original image Information is lost on both sides. The squeezed film image is expanded to fulfill the entire screen at a ratio of 2.35:1. Black bands do not appear at the top and bottom but information is lost on the left and right margins. · This feature is available when the input signal is video, component (480I, 480P, 576I, 576P, 720P, 1080I) or RGB (525P or 625P signal from a scan converter). * If black bands appear on the top and bottom in the full size screen, select the 2.35:1 size screen to avoid phosphor burnin. 14:9 size screen When a 720P or 1080I signal is input: ANAMORPHIC 2.35:1 NORMAL size screen (4:3) The normal size screen is displayed. * The picture has the same size as video pictures with a 4 : 3 aspect ratio. ANAMORPHIC size screen The image is displayed at a 14:9 aspect ratio. * This feature is available when the input signal is video, component (480I, 480P, 576I, 576P) or RGB (525P or 625P signal from a scan converter). The image is expanded in the horizontal direction. * Images compressed in the horizontal direction ("squeezed images") are expanded in the horizontal direction and displayed on the entire screen with correct linearity. (Normal images are expanded in the horizontal direction.) STADIUM size screen Note: Do not allow the displayed in 4:3 mode for an extended period. This can cause a phosphor burn-in. The picture is expanded in the horizontal and vertical directions at different ratios. * Use this for watching normal video programs (4:3) with a wide screen. ZOOM size screen The picture is expanded in the horizontal and vertical direction, maintaining the original proportions. * Use this for theater size (wide) movies, etc. 12 Wide Screen Operation with Computer Signals Switch to the wide screen mode to expand the 4 : 3 image to fill the entire screen. 1. Press the WIDE button on the remote control. 2. Within 3 seconds ... Press the WIDE button again. The screen size switches as follows: NORMAL ANAMORPHIC ZOOM NORMAL size screen (4:3 or SXGA 5:4) Information Supported resolution See page 7 of Model Information for details on the display output of the various VESA signal standards supported by the monitor. When 852 (848) dot 480 line wide VGA* signals with a vertical frequency of 60 Hz and horizontal frequency of 31.7 (31.0) kHz are input Select an appropriate setting for RGB SELECT mode referring to the"Table of Signals Supported" on page 7 of Model Information. * "VGA", "SVGA" and "SXGA" are registered trademarks of IBM, Inc. of the United States. Note: Do not allow the displayed in 4:3 mode for an extended period. This can cause a phosphor burn-in. The picture has the same size as the normal computer image. ANAMORPHIC size screen The image is expanded in the horizontal direction. ZOOM size screen When wide signals are input. ANAMORPHIC size screen 13 OSM (On Screen Menu) Controls Menu Operations The following describes how to use the menus and the selected items. 1. Press the MENU/ENTER button on the remote control to display the MAIN MENU. MAIN MENU PICTURE AUDIO IMAGE ADJ. SEL. MENU/ENTER OK SET UP FUNCTION SIGNAL INFO. EXIT EXIT 2. Press the cursor buttons v w on the remote control to highlight the menu you wish to enter. 3. Press the MENU/ENTER button on the remote control to select a sub menu or item. PICTURE : OFF PICTURE MEMORY CONTRAST BRIGHTNESS SHARPNESS COLOR R TINT : OFF NR : MIDDLE COLOR TEMP. : 2.2 GAMMA : AUTO LOW TONE : 0% SET UP LEVEL COLOR TUNE : ON CINEMA MODE : NORMAL PICTURE MODE SEL. MENU/ENTER OK ADJ. EXIT RETURN G 4. Adjust the level or change the setting of the selected item by using the cursor buttons on the remote control. CONTRAST 10 5. The adjustments or the settings that are stored in memory. The change is stored until you change it again. 6. Repeat steps 2 ­ 5 to adjust an additional item, or press the EXIT button on the remote control to return to the main menu. * When adjusting using the bar at the bottom of the screen, press the or button within 5 seconds. If not, the current setting is set and the previous screen appears. Note: The main menu disappears by pressing the EXIT button. 14 Menu Tree :Shaded areas indicate the default value. : Press the or button to adjust. The default value is at the center. Main menu PICTURE Sub menu PICTURE MEMORY CONTRAST BRIGHTNESS SHARPNESS COLOR TINT NR COLOR TEMP. WHITE BALANCE Sub menu 2 Sub menu 3 Sub menu 4 RESET YES YES YES YES YES YES YES YES YES YES YES YES YES YES YES YES YES YES YES YES YES YES YES YES YES YES YES RESET YES YES YES YES YES YES REFERENCE 17 17 17 17 17 17 17 18 18 18 18 18 18 18 18 18 18 19 19 19 19 19 19 19 19 19 19 REFERENCE 20 20 20 20 20 20 OFF/MEMORY1-6 05272 03264 01632 03264 RG 03264 OFF/NR-1/NR-2/NR-3 LOW/MIDDLE LOW/MIDDLE/HIGH GAIN RED 070 GAIN GREEN 070 GAIN BLUE 070 BIAS RED 070 BIAS GREEN 070 BIAS BLUE 070 RESET OFFON 2.12.22.32.4 AUTO1...3 0%3.75%7.5% RED YM 064 GREEN CY 064 BLUE MC 064 YELLOW GR 064 MAGENTA RB 064 CYAN BG 064 RESET OFFON ONOFF DEFAULT/THEATER1/THEATER2/NORMAL/BRIGHT Sub menu 2 Sub menu 3 Sub menu 4 GAMMA LOW TONE SET UP LEVEL COLOR TUNE CINEMA MODE PICTURE MODE Main menu AUDIO Sub menu BASS TREBLE BALANCE AUDIO INPUT1 AUDIO INPUT2 AUDIO INPUT3 01326 01326 LR -220+22 VIDEO 1-3 / HD/DVD 1-3 / RGB 1-3 VIDEO 1-3 / HD/DVD 1-3 / RGB 1-3 VIDEO 1-3 / HD/DVD 1-3 / RGB 1-3 Main menu IMAGE ADJUST Sub menu ASPECT MODE V-POSITION H-POSITION V-HEIGHT H-WIDTH AUTO PICTURE FINE PICTURE*1 PICTURE ADJ.*1 Sub menu 2 Sub menu 3 Sub menu 4 RESET NO YES YES YES YES NO YES YES REFERENCE 20 20 20 20 20 20 20 20 ZOOM/NORMAL/ANAMORPHIC/STADIUM/14:9/2.35:1 -640+64 -1280+127 064 064 ONOFF*2 *2 064 *2 0128 Sub menu 2 Sub menu 3 Sub menu 4 Main menu SET UP Sub menu LANGUAGE BNC INPUT D-SUB INPUT HD SELECT RGB SELECT DVI SET UP COLOR SYSTEM BACK GROUND GRAY LEVEL S1/S2 DISPLAY OSM OSM ADJ. ALL RESET RESET NO YES YES NO YES NO NO NO YES YES YES YES YES -- REFERENCE 21 21 21 21 21 22 22 22 22 23 23 23 23 23 ENGLISH/DEUTSCH/FRANÇAIS/ESPAÑOL/ITALIANO/SVENSKA/ / RGBCOMPONENT RGB 1080I/1035I/540P AUTO/STILL/MOTION/WIDE1/WIDE2/WIDE3/DTV PLUG/PLAY PCSTB/DVD BLACK LEVEL LOWHIGH AUTO/PAL/PAL-M/PAL-N/PAL 60/SECAM/4.43 NTSC/3.58NTSC BLACK/GRAY 0...3...15 AUTOOFF ONOFF TOP LEFTTOP CENTERTOP RIGHTBTM LEFTBTM CENTERBTM RIGHT ONOFF 15 Main menu FUNCTION Sub menu POWER MGT. INPUT SKIP PDP SAVER Sub menu 2 Sub menu 3 Sub menu 4 RESET YES YES YES YES YES YES YES YES YES YES YES YES REFERENCE 24 24 24 25 25 25 25 25 26 26 26 26 CLOSED CAPTION CAPTION CONT ONOFF ONOFF MANUAL/AUTO PEAK BRIGHT 100%/75%/50%/25% ORBITER OFF/AUTO1/AUTO2 INVERSE/WHITE OFF/INVERSE/WHITE SCREEN WIPER ON/OFF SOFT FOCUS OFF/LEVEL1-4 OSM ORBITER ON/OFF OSM CONTRAST LOW/NORMAL OFF/CAPTION1-4/TEXT1-4 LOW/NORMAL Main menu SIGNAL INFO. Sub menu Sub menu 2 Sub menu 3 Sub menu 4 RESET -- REFERENCE 26 *1 Only when AUTO PICTURE is OFF. *2 RGB/PC only Information Restoring the factory default settings Select "ALL RESET" under the SET UP menu. Note that this also restores other settings to the factory defaults. 16 Picture Settings Menu Storing picture settings This function allows you to store in memory the current input signal and PICTURE menu settings and to recall these settings when necessary. There are six picture memories, and notes of up to 15 characters can be added to each. Example: Storing picture settings at MEMORY1 On "PICTURE MEMORY" of "PICTURE" menu, select "MEMORY1", then press the MENU/ENTER button. The "PICTURE MEMORY" screen appears. PICTURE MEMORY MEMORY1 SET INPUT : DVD/HD1 SIGNAL : 480P NOTE : DVD/STAR WARS MEMORY2 INPUT : -- SIGNAL : -- NOTE : -- MEMORY3 INPUT : -- SIGNAL : -- NOTE : -- NEXT PAGE SEL. MENU/ENTER OK ADJ. 1/2 RESET PICTURE MEMORY PREVIOUS PAGE MEMORY4 SET INPUT : -- SIGNAL : -- NOTE : -- MEMORY5 INPUT : -- SIGNAL : -- NOTE : -- MEMORY6 INPUT : -- SIGNAL : -- NOTE : -- SEL. ADJ. MENU/ENTER OK 2/2 RESET Adjusting the picture The contrast, brightness, sharpness, color and tint can be adjusted as desired. Example: Adjusting the contrast On "CONTRAST" of "PICTURE" menu, adjust the contrast. PICTURE : OFF PICTURE MEMORY CONTRAST BRIGHTNESS SHARPNESS COLOR R TINT : OFF NR : MIDDLE COLOR TEMP. : 2.2 GAMMA : AUTO LOW TONE : 0% SET UP LEVEL COLOR TUNE : ON CINEMA MODE : NORMAL PICTURE MODE SEL. ADJ. EXIT RETURN G CONTRAST 10 Note: If "CAN NOT ADJUST" appears ... When trying to enter the PICTURE submenu, make sure PICTURE MODE is not set to DEFAULT. Information Picture adjustment screen CONTRAST: Changes the picture's white level. BRIGHTNESS: Changes the picture's black level. SHARPNESS: Changes the picture's sharpness. Adjusts picture detail of VIDEO display. COLOR: Changes the color density. TINT: Changes the picture's tint. Adjust for natural colored skin, background, etc. Adjusting the computer image Only the contrast and brightness can be adjusted when a computer signal is connected. Restoring the factory default settings Select "DEFAULT" under the "PICTURE MODE" settings. EXIT RETURN EXIT RETURN Information PICTURE MEMORY Settings OFF: Picture memory not used. MEMORY1 to 6: Picture memory with the specified number used. Maximum memories are 6, not depending on inputs. Setting the memory · Use the v and w button to select the desired memory place, MEMORY1 to MEMORY6. · Use the and buttons to select "SET", then press the MENU/ENTER button. · If necessary, input a note. Resetting the memory Use the v and w button to select the desired memory place, MEMORY1 to MEMORY6, then use the and buttons to select "RESET", and finally press the MENU/ENTER button. The memory is cleared, and "--" is displayed in the "INPUT", "SIGNAL" and "NOTE" columns. Inputting notes · Use the and buttons to select "NOTE", then press the MENU/ENTER button. · Input the note. Use the v and w button to select the character. Use the and buttons to move the cursor. Use the EXIT button to delete the character at the cursor position. · When you have finished inputting the note, press the MENU/ENTER button. Reducing noise in the picture Use these settings if the picture has noise due to poor reception or when playing video tapes on which the picture quality is poor. Example: Setting "NR-3" On "NR" of "PICTURE" menu, select "NR-3". PICTURE : OFF PICTURE MEMORY CONTRAST BRIGHTNESS SHARPNESS COLOR R TINT : OFF NR : MIDDLE COLOR TEMP. : 2.2 GAMMA : AUTO LOW TONE : 0% SET UP LEVEL COLOR TUNE : ON CINEMA MODE : NORMAL PICTURE MODE SEL. ADJ. EXIT RETURN G NR : NR-3 Information NR * "NR" stands for Noise Reduction. * This function reduces noise in the picture. Types of noise reduction There are three types of noise reduction. Each has a different level of noise reduction. The effect becomes stronger as the number increases (in the order NR-1 NR-2 NR-3). OFF: Turns the noise reduction function off. 17 Setting the color temperature Use this procedure to set color tone produced by the plasma display. Example: Setting "HIGH" On "COLOR TEMP." of "PICTURE" menu, select "HIGH". PICTURE : OFF PICTURE MEMORY CONTRAST BRIGHTNESS SHARPNESS COLOR R TINT : OFF NR : HIGH COLOR TEMP. : 2.2 GAMMA : AUTO LOW TONE : 0% SET UP LEVEL COLOR TUNE : ON CINEMA MODE : NORMAL PICTURE MODE SEL. ADJ. EXIT RETURN Changing the Gamma Curve This feature adjusts the brightness of the midtone areas while keeping shadows and highlights unchanged. Example: Setting "2.3" On "GAMMA" of "PICTURE" menu, select "2.3". PICTURE : OFF PICTURE MEMORY CONTRAST BRIGHTNESS SHARPNESS COLOR R TINT : OFF NR : MIDDLE COLOR TEMP. : 2.3 GAMMA : AUTO LOW TONE : 0% SET UP LEVEL COLOR TUNE : ON CINEMA MODE : NORMAL PICTURE MODE SEL. ADJ. EXIT RETURN G G Information Setting the color temperature LOW: Redder MIDDLE LOW: Slightly red MIDDLE: Standard (slightly bluer) HIGH: Bluer Information GAMMA settings The picture becomes darker as the number increases (in the sequence of 2.1, 2.2, 2.3, 2.4). * These values are approximate. Adjusting the color to the desired level Use this procedure to adjust the white balance for each color temperature to achieve the desired color quality. Example: Adjusting the "GAIN RED" of "HIGH" color temperature On "COLOR TEMP." of "PICTURE" menu, select "HIGH", then press the MENU/ENTER button. The "WHITE BALANCE" screen appears. On "GAIN RED", adjust the white balance. WHITE BALANCE COLOR TEMP. HIGH GAIN RED GAIN GREEN GAIN BLUE BIAS RED BIAS GREEN BIAS BLUE : OFF RESET SEL. ADJ. EXIT RETURN Making the Low Tone adjustments This feature allows more detailed tone to be reproduced especially in the dark area. Example: Setting "2" On "LOW TONE" of "PICTURE" menu, select "2". PICTURE : OFF PICTURE MEMORY CONTRAST BRIGHTNESS SHARPNESS COLOR R TINT : OFF NR : MIDDLE COLOR TEMP. : 2.2 GAMMA :2 LOW TONE : 0% SET UP LEVEL COLOR TUNE : ON CINEMA MODE : NORMAL PICTURE MODE SEL. ADJ. EXIT RETURN G GAIN RED 20 Information Adjusting the white balance GAIN R/G/B: White balance adjustment for white level BIAS R/G/B: White balance adjustment for black level RESET: Resets settings to the factory default values. Use and buttons to select "ON", then press the MENU/ENTER button. Restoring the factory default settings Select "RESET" under the WHITE BALANCE menu. Information LOW TONE settings AUTO: Will automatically appraise the picture and make adjustments. 1: Will apply the dither method suitable for still pictures. 2: Will apply the dither method suitable for motion pictures. 3: Will apply the error diffusion method. 18 Adjusting the pedestal level (black level) This feature adjusts the video black level in a video image. Example: Setting "3.75%" On "SET UP LEVEL" of "PICTURE" menu, select "3.75%". PICTURE : OFF PICTURE MEMORY CONTRAST BRIGHTNESS SHARPNESS COLOR R TINT : OFF NR : MIDDLE COLOR TEMP. : 2.2 GAMMA : AUTO LOW TONE : 3.75% SET UP LEVEL COLOR TUNE : ON CINEMA MODE : NORMAL PICTURE MODE SEL. ADJ. EXIT RETURN Setting the picture to suit the movie The film image is automatically discriminated and projected in an image mode suited to the picture. [NTSC, PAL, PAL60, 480I (60Hz), 525I (60Hz), 576I (50Hz), 625I (50Hz), 1035I (60Hz), 1080I (60Hz) only] Example: Setting the "CINEMA MODE" to "OFF" On "CINEMA MODE" of "PICTURE" menu, select "OFF". PICTURE : OFF PICTURE MEMORY CONTRAST BRIGHTNESS SHARPNESS COLOR R TINT : OFF NR : MIDDLE COLOR TEMP. : 2.2 GAMMA : AUTO LOW TONE : 0% SET UP LEVEL COLOR TUNE : OFF CINEMA MODE : NORMAL PICTURE MODE SEL. ADJ. EXIT RETURN G G Information SET UP LEVEL settings 0%: Normal status 3.75%: 3.5% lower than normal 7.5%: 7.5% lower than normal Adjusting the colors Use this procedure to adjust hue and color density for red, green, blue, yellow, magenta and cyan. You can accentuate the green color of trees, the blue of the sky, etc. Example: Adjusting the color tune for blue On "PICTURE" menu, select "COLOR TUNE", then press the MENU/ENTER button. The "COLOR TUNE" screen appears. On "BLUE" of "COLOR TUNE", adjust the color tune. COLOR TUNE RED GREEN BLUE YELLOW MAGENTA CYAN RESET SEL. ADJ. Y C M G R B M Y C R B G Information CINEMA MODE ON: Automatic discrimination of the image and projection in cinema mode. OFF: Cinema mode does not function. Setting the picture mode according to the brightness of the room There are four picture modes that can be used effectively according to the environment in which you are viewing the display. Example: Setting the "THEATER1" mode On "PICTURE MODE" of "PICTURE" menu, select "THEATER1". PICTURE : OFF PICTURE MEMORY CONTRAST BRIGHTNESS SHARPNESS COLOR R TINT : OFF NR : MIDDLE COLOR TEMP. : 2.2 GAMMA : AUTO LOW TONE : 0% SET UP LEVEL COLOR TUNE : ON CINEMA MODE : NORMAL PICTURE MODE SEL. ADJ. EXIT RETURN G : OFF EXIT RETURN PICTURE MODE : THEATER1 Information COLOR TUNE settings RED: Makes red's adjustment GREEN: Makes green's adjustment BLUE: Makes blue's adjustment YELLOW: Makes yellow's adjustment MAGENTA: Makes magenta's adjustment CYAN: Makes cyan's adjustment RESET: Resets settings to the factory default value. and buttons to select "ON", then press the Use MENU/ENTER button. Information Types of picture modes THEATER1, 2: Set this mode when watching video in a dark room. This mode provides darker, finer pictures, like the screen in movie theaters. For a darker image, select THEATER2. NORMAL: Set this mode when watching video in a bright room. This mode provides dynamic pictures with distinct differences between light and dark sections. BRIGHT: This mode provides brighter pictures than NORMAL. DEFAULT: Use this to reset the picture to the factory default settings. 19 Audio Settings Menu Adjusting the treble, bass and left/right balance and audio input select The treble, bass and left/right balance can be adjusted to suit your tastes. Example: Adjusting the bass On "BASS" of "AUDIO" menu, adjust the bass. AUDIO BASS TREBLE BALANCE AUDIO INPUT1 AUDIO INPUT2 AUDIO INPUT3 SEL. ADJ. Image Adjust Settings Menu Adjusting the Position, Size, Fine Picture, Picture Adj The position of the image can be adjusted and flickering of the image can be corrected. Example: Adjusting the vertical position in the normal mode On "V-POSITION" of "IMAGE ADJUST" menu, adjust the position. The mode switches as follows each time the or button is pressed: NORMAL ANAMORPHIC : VIDEO1 : HD/DVD1 : RGB1 EXIT RETURN Note : If "CAN NOT ADJUST" appears... Set "AUDIO INPUT" on the AUDIO menu correctly. Information Audio settings menu BASS: Controls the level of low frequency sound. TREBLE: Controls the level of high frequency sound. BALANCE: Controls the balance of the left and right channels. * The mode can also be switched by pressing the WIDE button on the remote control. * The settings on the IMAGE ADJUST menu are not preset at the factory. IMAGE ADJUST : NORMAL ASPECT MODE V-POSITION H-POSITION V-HEIGHT H-WIDTH : OFF AUTO PICTURE FINE PICTURE PICTURE ADJ. SEL. ADJ. EXIT RETURN V-POSITION -30 Setting the allocation of the audio connectors Setting the AUDIO 1, 2, and 3 connectors to the desired input. Example: Setting "AUDIO INPUT1" to "VIDEO 2" On "AUDIO INPUT1" of "AUDIO" menu, select "VIDEO2". The available sources depend on the settings of input. AUDIO BASS TREBLE BALANCE AUDIO INPUT1 AUDIO INPUT2 AUDIO INPUT3 SEL. ADJ. Information When "AUTO PICTURE" is "OFF" IMAGE ADJUST : ANAMORPHIC ASPECT MODE V-POSITION H-POSITION V-HEIGHT H-WIDTH : OFF AUTO PICTURE FINE PICTURE PICTURE ADJ. SEL. ADJ. EXIT RETURN : VIDEO2 : HD/DVD1 : RGB1 EXIT RETURN Information AUDIO INPUT A single audio input cannot be selected as the audio channel for more than one input terminal. When Auto Picture is off, the Fine Picture and the Picture ADJ. items are displayed so that you can adjust them. Adjusting the Auto Picture ON: The Picture ADJ., Fine Picture and Position adjustments are made automatically. Not available for digital ZOOM. OFF: The Picture ADJ., Fine Picture and Position adjustments are made manually. * If FINE PICTURE can't be adjusted, set Auto Picture to OFF and adjust manually. Adjusting the position of the image V-POSITION: Adjusts the vertical position of the image. H-POSITION: Adjusts the horizontal position of the image. V-HEIGHT: Adjusts the vertical size of the image. (Except for STADIUM mode) H-WIDTH: Adjusts the horizontal size of the image. (Except for STADIUM mode) FINE PICTURE*: Adjusts for flickering. PICTURE ADJ.*: Adjusts for striped patterns on the image. * The Picture ADJ. and Fine Picture features are available only when the "Auto Picture" is off. * The AUTO PICTURE, FINE PICTURE and PICTURE ADJ. are available only for RGB signals. But, these features are not available for moving pictures on VIDEO, HD/DVD or RGB. 20