AccuSync LCD51VM/LCD71VM TM Index Warning .................................................................................................................... 1 Contents ................................................................................................................. 2 Quick Start ............................................................................................................. 3 Controls ...................................................................................................................7 Recommended Use .............................................................................................. 10 Specifications ....................................................................................................... 12 Features ............................................................................................................... 14 Troubleshooting ................................................................................................... 15 References ............................................................................................................. 16 Limited Warranty ................................................................................................. 17 TCO `99 .................................................................................................................. 18 Avertissement ...................................................................................................... 21 Contenu ................................................................................................................. 22 Mise en marche rapide ...................................................................................... 23 Commandes .......................................................................................................... 27 Usage recommandé ............................................................................................ 30 Spécifications ...................................................................................................... 32 Fonctions ............................................................................................................. 34 Dépannage ............................................................................................................ 35 Références ........................................................................................................... 36 Garantie limitée .................................................................................................. 37 TCO `99 .................................................................................................................. 38 WARNING TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT USE THIS UNIT'S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS THE PRONGS CAN BE FULLY INSERTED. REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. CAUTION CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, MAKE SURE POWER CORD IS UNPLUGGED FROM WALL SOCKET. TO FULLY DISENGAGE THE POWER TO THE UNIT, PLEASE DISCONNECT THE POWER CORD FROM THE AC OUTLET. DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol warns user that uninsulated voltage within the unit may have sufficient magnitude to cause electric shock. Therefore, it is dangerous to make any kind of contact with any part inside this unit. This symbol alerts the user that important literature concerning the operation and maintenance of this unit has been included. Therefore, it should be read carefully in order to avoid any problems. Canadian Department of Communications Compliance Statement DOC: This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. C-UL: Bears the C-UL Mark and is in compliance with Canadian Safety Regulations according to CAN/CSA C22.2 No. 60950. FCC Information 1. Use the attached specified cables with the AccuSync LCD51VM (L152R5) or AccuSync LCD71VM (L172R6) color monitor so as not to interfere with radio and television reception. (1) Please use the supplied power cord or equivalent to ensure FCC compliance. (2) Please use the supplied shielded video signal cable. Use of other cables and adapters may cause interference with radio and television reception. 2. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. · Consult your dealer or an experienced radio/TV technician for help. If necessary, the user should contact the dealer or an experienced radio/television technician for additional suggestions. The user may find the following booklet, prepared by the Federal Communications Commission, helpful: "How to Identify and Resolve Radio-TV Interference Problems." This booklet is available from the U.S. Government Printing Office, Washington, D.C., 20402, Stock No. 004-000-00345-4. 1 AS5171VMManual042403.p65 1 5/6/03, 10:05 AM Contents Your new NEC AccuSync LCD monitor box* should contain the following: · AccuSync LCD monitor with tilt base · Power Cord · User's Manual · Audio Cable · Video Signal Cable · Base stand Power Cord Video Signal Cable Audio Cable AccuSync LCD monitor (base stand not connected) User's Manual Base Stand * Remember to save your original box and packing material to transport or ship the monitor. 2 AS5171VMManual042403.p65 2 5/6/03, 10:05 AM Quick Start To attach the Base to the LCD Stand: 1. Insert the front of the LCD Stand into the holes in the front of the Base. 2. Next, position the locking tabs on the back side of the LCD Stand with the holes on the Base. Lower the Stand until locking tabs are secure. Stand 1 Locking Tabs Base 2 Front Base To attach the AccuSync LCD monitor to your system, follow these instructions: 1. Turn off the power to your computer. 2. For the PC with Analog output: Connect the 15-pin mini D-SUB signal cable to the connector of the display card in your system (Figure A.1). Tighten all screws. For the MAC: Connect the AccuSync Macintosh cable adapter to the computer, then attach the 15-pin mini D-SUB signal cable to the AccuSync Macintosh cable adapter (Figure A.2). Tighten all screws. NOTE: To obtain the AccuSync Macintosh cable adapter, call NEC-Mitsubishi Electronics Display of America, Inc. at (800) 632-4662. 3. Connect the 15-pin mini D-SUB of the video signal cable to the appropriate connector on the back of the monitor (Figure B.1). Connect the audio cable to AUDIO-INPUT on the back of the monitor and the other end to the "Audio out" terminal of the computer. Headphones may be connected to the "Headphones" output on the back of the monitor " ". While the headphones are connected, the sound from the speakers will be disabled. Headphones can be purchased from your local electronics store. 4. Connect one end of the power cord to the LCD and the other end to the power outlet. Place the video signal cable and power cord between the cable holder (Figure B.1). NOTE: Adjust the position of cables between the holder to avoid damage. NOTE: If you use this monitor at AC125-240V, please refer to Recommended Use section of this manual for proper selection of power cord. 5. Turn on the monitor with the front power button and the computer. (Figure C.1) 6. No-touch Auto Adjust automatically adjusts the monitor to optimal settings upon initial setup for most timings. For further adjustments, use the following OSM® controls: · Auto Adjust Contrast · Auto Adjust Refer to the Controls section of this User's Manual for a full description of these OSM controls. NOTE: For download information on the Windows® 95/98/Me/2000/XP INF file for your AccuSync monitor, refer to the References section of this User's Manual. NOTE: If you have any problems, please refer to the Troubleshooting section of this User's Manual. 3 AS5171VMManual042403.p65 3 5/6/03, 10:06 AM Quick Start ­continued Figure A.1 Macintosh Cable Adapter (not include) Figure A.2 Note: Some Macintosh systems do not require a Macintosh Cable Adapter Headphone Audio input Input (D-Sub) Figure B.1 Cable holder Power button Figure C.1 4 AS5171VMManual042403.p65 4 5/6/03, 10:06 AM Quick Start ­continued Tilt Grasp both sides of the monitor screen with your hands and adjust the tilt as desired (Figure TS.1). Figure TS.1 Remove Monitor Stand for Mounting To prepare the monitor for alternate mounting purposes: 1. Disconnect all cables. 2. Place monitor face down on a nonabrasive surface (Figure R.1). 3. Remove the 2 screws on the stand and lift off the stand (Figure R.1). 4. Remove the 4 screws connecting the monitor to the stand and remove the metal plate (Figure R.2). The monitor is now ready for mounting in an alternate manner. 5. Connect the AC cord and signal cable to the back of the monitor (Figure R.3). 6. Reverse this process to reattach stand. NOTE: Use only VESA-compatible alternative mounting method. NOTE: Handle with care when removing monitor stand. Figure R.1 non-abrasive surface Figure R.2 Figure R.3 5 AS5171VMManual042403.p65 5 5/6/03, 10:06 AM Quick Start ­continued Removing the Base Note: Always remove the Base when shipping the LCD. 1. Place monitor face down on a non-abrasive surface (Figure R.1). 2. While using your thumbs, press the bottom tabs upward to unlock. 3. Press the top tabs down to unlock and pull off the stand. Connecting a Flexible Arm This LCD monitor is designed for use with a flexible arm. Please use the attached screws (4pcs) as shown in the picture when installing. To meet the safety requirements, the monitor must be mounted to an arm which guaranties the necessary stability under consideration of the weight of the monitor. The LCD monitor should only be used with an approved arm (e.g. GS mark). Replace screws Thickness of Bracket (Arm) 2.0~3.2 mm Tighten all screws. 75 mm (LCD51VM) 100 mm (LCD71VM) Specifications 4-SCREWS (M4) (MAX depth: 8.5 mm) 75 mm (LCD51VM) 100 mm (LCD71VM) If using other screws, check depth of holes. Weight of LCD assembly: 2.6 kg - LCD51VM (MAX) 4.0 kg -LCD71VM (MAX) 6 AS5171VMManual042403.p65 6 5/6/03, 10:06 AM Controls OSM® (On-Screen Manager) control buttons on the front of the monitor function as follows: 1. Basic key function Button OSM Off OSM On (Icon selection stage) SELECT OSM displayed Moves to Adjustment stage Moves to Icon selection stage ­ Shortcut to bright adjust window Cursor moves left + Shortcut to volume adjust window Cursor moves left AUTO / RESET "Auto adjust" function OSM On (Adjustment stage) Adjust value decrease or Cursor for adjust moves left Adjust value increase or Cursor for adjust moves right Reset operation Mute off/on Volume adjustment window 2. OSM Structure Main Menu (Icon Select) Press "SELECT" key Press "SELECT" key VOLUME MUTE Main Menu (Adjust) % Press "SELECT" key Adjust by using "­" or " +". Press "SELECT" key Press "SELECT" key Press "­" or " +" Press "­" or " +" Sub Menu (Icon Select) Press "SELECT" key Adjust by using "­" or " +". Sub Menu (Adjust) 7 AS5171VMManual042403.p65 7 5/6/03, 10:06 AM Controls ­continued AUDIO Control the sound volume of speakers and headphone. To mute the speaker sound, press the AUTO/RESET key. BRIGHTNESS Adjusts the overall image and background screen brightness. CONTRAST Adjusts the image brightness in relation to the background. AUTO CONTRAST Adjusts the image displayed for non-standard video inputs. AUTO ADJUST Automatically adjusts the Image Position, the H. Size and Fine setting. LEFT/RIGHT Controls Horizontal Image Position within the display area of the LCD. DOWN/UP Controls Vertical Image Position within the display area of the LCD. H. SIZE Adjusts the horizontal size by increasing or decreasing this setting. FINE Improves focus, clarity and image stability by increasing or decreasing this setting. COLOR CONTROL SYSTEMS Four color ...