MultiSync LCD1560NX ® TM Index Warning .................................................................................................................... 1 Contents ................................................................................................................. 2 Quick Start ............................................................................................................. 3 Controls ...................................................................................................................7 Recommended Use .............................................................................................. 10 Specifications ....................................................................................................... 12 Features ................................................................................................................. 13 Troubleshooting .................................................................................................. 14 References ............................................................................................................. 15 Limited Warranty ................................................................................................. 16 TCO'95 ..................................................................................................................... 17 TCO'99 ..................................................................................................................... 19 Avertissement ..................................................................................................... 22 Contenu ................................................................................................................. 23 Mise en marche rapide ...................................................................................... 24 Commandes .......................................................................................................... 28 Usage recommandé ............................................................................................. 31 Fiche technique ................................................................................................... 33 Fonctions .............................................................................................................. 34 Dépannage ............................................................................................................ 35 Références ........................................................................................................... 36 Garantie limitée .................................................................................................. 37 TCO'95 .................................................................................................................... 38 TCO'99 .................................................................................................................... 40 WARNING TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT USE THIS UNIT'S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS THE PRONGS CAN BE FULLY INSERTED. REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. CAUTION CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, MAKE SURE POWER CORD IS UNPLUGGED FROM WALL SOCKET. TO FULLY DISENGAGE THE POWER TO THE UNIT, PLEASE DISCONNECT THE POWER CORD FROM THE AC OUTLET.DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol warns user that uninsulated voltage within the unit may have sufficient magnitude to cause electric shock. Therefore, it is dangerous to make any kind of contact with any part inside this unit. This symbol alerts the user that important literature concerning the operation and maintenance of this unit has been included. Therefore, it should be read carefully in order to avoid any problems. Canadian Department of Communications Compliance Statement DOC: This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. C-UL: Bears the C-UL Mark and is in compliance with Canadian Safety Regulations according to CAN/CSA C22.2 No. 950. FCC Information 1. Use the attached specified cables with the MultiSync LCD1560NX (NL2501) color monitor so as not to interfere with radio and television reception. (1) Please use the supplied power cord or equivalent to ensure FCC compliance. (2) Please use the supplied shielded video signal cable. Use of other cables and adapters may cause interference with radio and television reception. 2. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. · Consult your dealer or an experienced radio/TV technician for help. If necessary, the user should contact the dealer or an experienced radio/television technician for additional suggestions. The user may find the following booklet, prepared by the Federal Communications Commission, helpful: "How to Identify and Resolve Radio-TV Interference Problems." This booklet is available from the U.S. Government Printing Office, Washington, D.C., 20402, Stock No. 004-000-00345-4. 1 LCD1560NX.p65 1 10/7/02, 3:09 PM Contents Your new NEC MultiSync® LCD monitor box* should contain the following: · MultiSync LCD1560NXTM monitor with tilt base · Power Cord · Video Signal Cable · User's Manual Power Cord Video Signal Cable MultiSync LCD1560NX ® TM User's Manual * Remember to save your original box and packing material to transport or ship the monitor. 2 LCD1560NX.p65 2 10/7/02, 3:09 PM Quick Start To attach the MultiSync® LCD monitor to your system, follow these instructions: 1. Turn off the power to your computer. 2. For the PC or MAC with DVI digital output: Connect the DVI signal cable (not included) to the connector of the display card in your system (Figure A.1). Tighten all screws. For the PC with Analog output: Connect the 15-pin mini D-SUB signal cable to the connector of the display card in your system (Figure A.2). Tighten all screws. For the MAC: Connect the MultiSync Macintosh cable adapter to the computer, then attach the 15-pin mini D-SUB signal cable to the MultiSync Macintosh cable adapter (Figure B.1). Tighten all screws. NOTE: To obtain the MultiSync LCD1560NXTM Macintosh cable adapter, call NECMitsubishi Electronics Display of America, Inc. at (800) 632-4662. 3. Remove the cable cover. Connect the 15-pin mini D-SUB of the video signal cable and DVI signal cable (not included) to the appropriate connector on the back of the monitor (Figure C.1). 4. Connect one end of the power cord to the monitor and the other end to the power outlet. Place the Video Signal Cable and power cord under Cable cover (Figure C.1). Replace cable cover. NOTE: Adjust position of cable that place under cable cover, to avoid damage for cable or monitor. NOTE: If you use this monitor at AC125-240V, please refer to Recommended Use section of this manual for proper selection of power cord. 5. The vacation switch on the right side of the monitor must be turned on (Figure D.1). Turn on the monitor with the front power button and the computer. NOTE: The vacation switch is a true on/off switch. If this switch is on the OFF position, the monitor cannot be turned on using the front button. DO NOT switch on/off repeatedly. 6. Analog input only: No-touch Auto Adjust automatically adjusts the monitor to optimal settings upon initial setup for most timings. For further adjustments, use the following OSM® controls: · Auto Adjust Contrast · Auto Adjust Refer to the Controls section of this User 's Manual for a full description of these OSM controls. NOTE: For download information on the Windows® 95/98/Me/2000/XP INF file for your MultiSync LCD1560NX monitor, refer to the References section of this User's Manual. NOTE: If you have any problems, please refer to the Troubleshooting section of this User's Manual. 3 LCD1560NX.p65 3 10/7/02, 3:09 PM Quick Start ­continued Figure A.2 DVI signal cable A.1 Input1(D-Sub) Input2(DVI) Cable cover B.1 Figure C.1 vacation switch power button Figure D.1 4 LCD1560NX.p65 4 10/7/02, 3:09 PM Quick Start ­continued Tilt Grasp both sides of the monitor screen with your hands and adjust the tilt as desired (Figure TS.1). Remove Monitor Stand for Mounting To prepare the monitor for alternate mounting purposes: 1. Disconnect all cables. 2. Place monitor face down on a non-abrasive surface (Figure R.1). 3. Remove the hinge cover (Figure R.1). 4. Remove the 4 screws connecting the monitor to the stand and lift off the stand assembly (Figure R.2). The monitor is now ready for mounting in an alternate manner. 5. Connect the AC cord and signal cable to the back of the monitor (Figure R.3). 6. Reverse this process to reattach stand. NOTE: Use only VESA-compatible alternative mounting method. NOTE: Handle with care when removing monitor stand. Figure TS.1 Hinge Cover Non-abrasive surface Figure R.1 Figure R.2 Figure R.3 5 LCD1560NX.p65 5 10/7/02, 3:09 PM Quick Start ­continued This LCD monitor is designed for use with a flexible arm. Please use the attached screws (4pcs) as shown in the picture when installing. To meet the safety requirements, the monitor must be mounted to an arm which guaranties the necessary stability under consideration of the weight of the monitor. The LCD monitor shall only be used with an approved arm (e.g. GS mark). Thickness of Bracket(Arm) 2.0~3.2mm Tighten all screws. Specifications If using other screws, check depth of hole. (MAX depth: 8.5mm) Weight of LCD assembly: 2.8kg(MAX) 6 LCD1560NX.p65 6 10/7/02, 3:09 PM Controls OSM® (On-Screen Manager) control buttons on the front of the monitor function as follows: To access OSM menu, press any of the control buttons ( <, >, ­, +, EXIT). To change signal input, press the SELECT button. NOTE: OSM must be closed in order to change signal input. Menu EXIT Exits the OSM controls. Exits to the OSM main menu. Moves the highlighted area left/right to select control menus. Moves the highlighted area up/down to select one of the controls. Moves the bar left/right to increase or decrease the adjustment. Active Auto Adjust function. Enter the OSM controls. Enter the OSM sub menu. Resets the highlighted control menu to the factory setting. ­/+ SELECT RESET NOTE: When RESET is pressed in the main and sub-menu, a warning window will appear allowing you to cancel the RESET function by pressing the EXIT button. Brightness/Contrast Controls BRIGHTNESS Adjusts the overall image and background screen brightness. CONTRAST Adjusts the image brightness in relation to the background. AUTO AUTO (Analog input only) Adjusts the image displayed for non-standard video inputs. Automatically adjusts the Image Position and H. Size settings and Fine settings. Auto Adjust (Analog input only) Image Controls (Analog input only) LEFT / RIGHT Controls Horizontal Image Position within the display area of the LCD. DOWN / UP Controls Vertical Image Position within the display area of the LCD. H.SIZE Adjusts the horizontal size by increasing or decreasing this setting. FINE Improves focus, clarity and image stability by increasing or decreasing this setting. 7 LCD1560NX.p65 7 10/7/02, 3:09 PM Controls ­continued AccuColor® Control Systems AccuColor Control Systems: Six color presets select the desired color setting. (NATIVE color preset cannot be changed.) R,G,B: Increases or decreases Red, Green or Blue color depending upon which is selected. The change in color will appear on screen and the direction (increase or decrease) will be shown by the bars. NATIVE: Original color presented by the LCD panel that is unadjustable. Tools LANGUAGE: OSM® control menus are available in seven languages. OSM Position: You can choose where you would like the OSM control image to appear on your screen. Selecting OSM Location allows you to ma ...