User manual NEC LT100

MultiSync LT 100 Ultra-Portable Projector Ultra-Portable Projector ® NEC Technologies, Inc. 1250 N. Arlington Heights Road, Suite 500 Itasca, Illinois 60143-1248 Part No. 78409941 Printed in Japan Projector User's Manual NEC Technologies TM IMPORTANT INFORMATION CAUTION TO PREVENT SHOCK, DO NOT OPEN THE CABINET. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED NEC SERVICE PERSONNEL. This symbol warns the user that uninsulated voltage within the unit may be sufficient to cause electrical shock. Therefore, it is dangerous to make any kind of contact with any part inside of the unit. This symbol alerts the user that important information concerning the operation and maintenance of this unit has been provided. The information should be read carefully to avoid problems. 1 Precautions Please read this manual carefully before using your NEC MultiSync LT100 Projector and keep the manual handy for future reference. Your serial number is located beneath the main power switch on the back of your MultiSync LT100. Record it here: CAUTION LASER RADIATIONDO NOT STARE INTO BEAM WAVE LENGTH: 670 nm MAX. OUTPUT: 1 mW CLASS II LASER PRODUCT WARNING TO PREVENT FIRE OR SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. DO NOT USE THIS UNIT'S GROUNDED PLUG WITH AN EXTENSION CORD OR IN AN OUTLET UNLESS ALL THREE PRONGS CAN BE FULLY INSERTED. DO NOT OPEN THE CABINET. THERE ARE HIGHVOLTAGE COMPONENTS INSIDE. ALL SERVICING MUST BE DONE BY QUALIFIED NEC SERVICE PERSONNEL. DOC Compliance Notice This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. RF Interference WARNING The Federal Communications Commission does not allow any modifications or changes to the unit EXCEPT those specified by NEC Technologies in this manual. Failure to comply with this government regulation could void your right to operate this equipment. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a commercial installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at their own expense. 2 3 Important Safeguards These safety instructions are to ensure the long life of your projector and to prevent fire and shock. Please read them carefully and heed all warnings. 7. If installing the projector on the ceiling: a. The ceiling must be strong enough to support the projector and the installation must be in accordance with any local building codes. b. The projector must be installed by qualified NEC service personnel. Installation 1. For best results, use your projector in a darkened room. 2. Place the projector on a flat, level surface in a dry area away from dust and moisture. 3. Do not place your projector in direct sunlight, near heaters or heat radiating appliances. 4. Exposure to direct sunlight, smoke or steam can harm internal components. 5. Handle your projector carefully. Dropping or jarring can damage internal components. 6. Do not place heavy objects on top of the projector. Power Supply 1. The projector is designed to operate on a power supply of 100-120 or 220-240 V 50/60 Hz AC. Ensure that your power supply fits this requirement before attempting to use your projector. 2. Handle the power cable carefully and avoid excessive bending. A damaged cord can cause electric shock or fire. 3. If the projector is not to be used for an extended period of time, disconnect the plug from the power outlet. Cleaning 1. Unplug the projector before cleaning. 2. Clean the cabinet periodically with a damp cloth. If heavily soiled, use a mild detergent. Never use strong detergents or solvents such as alcohol or thinner. 3. Use a blower or lens paper to clean the lens, and be careful not to scratch or mar the lens. Fire and Shock Precautions 1. Ensure that there is sufficient ventilation and that vents are unobstructed to prevent the build-up of heat inside your projector. Allow at least 3 inches (10cm) of space between your projector and a wall. 2. Prevent foreign objects such as paper clips and bits of paper from falling into your projector. Do not attempt to retrieve any objects that might fall into your projector. Do not insert any metal objects such as a wire or screwdriver into your project. If something should fall into your projector, disconnect it immediately and have the object removed by a qualified NEC service person. 3. Do not place any liquids on top of your projector. Lamp Replacement · Perform lamp replacement in accordance with the instructions on page 77. · Be sure to replace the lamp when the Status light comes on. If you continue to use the lamp after 1000 hours of use, the lamp bulb may shatter, and pieces of glass may be scattered in the lamp case. Do not touch them as the pieces of glass may cause injury. If this happens, contact your NEC dealer for lamp replacement. · Allow a minimum of ONE minute to elapse between turning the lamp off and on. High voltage is applied to the lamp immediately when the power is turned on. Therefore turning the power off and quickly back on may shorten the life of your lamp and result in damage to your projector. · Do not look into the lens while the projector is on. Serious damage to your eyes could result. · Do not look into the laser pointer while it is on and do not point the laser beam at another person. Serious injury could result. 4 5 ATTENTION RISQUE D'ELECTROCUTION NE PAS OUVRIR ATTENTION RAYONNEMENT LASER NE PAS REGARDER DANS LE FAISCEAU LONGUEUR D'ONDE: 670 nm MAX. SORTIE: 1 mW APPREIL A LASER DE CLASSE 2 Ce symbole a pour but de prévenir l'utilisateur de la présence d'une tension dangereuse, non isolée se trouvant à l'intérieur de l'appareil. Elle est d'une intensité suffisante pour constituer un risque d'électrocution. Eviter le contact avec les pièces à l'intérieur de cet appareil. Ce symbole a pour but de prévenir l'utilisateur de la présence d'importantes instructions concernant l'entretien et le fonctionnement de cet appareil. Par conséquent, elles doivent être lues attentivement afin d'éviter des problèmes. AVERTISSEMENT AFIN DE REDUIRE LES RISQUES D'INCENDIE OU D'ELECTROCUTION, NE PAS EXPOSER CET APPAREIL A LA PLUIE OU A L'HUMIDITE. AUSSI, NE PAS UTILISER LA FICHE POLARISEE AVEC UN PROLONGATEUR OU UNE AUTRE PRISE DE COURANT SAUF SI CES LAMES PEUVENT ETRE INSEREES A FOND. NE PAS OUVRIR LE COFFRET, DES COMPOSANTES HAUTE TENSION SE TROUVENT A L'INTERIEUR. LAISSER A UN PERSONNEL QUALIFIE LE SOIN DE REPARER CET APPAREIL. Importantes précautions de sécurité Les points suivants sont des précautions de sécurité importantes destinées à garantir une longue durée de service du projecteur et afin d'éviter un incendie et des risques d'électrocution. S'assurer de lire attentivement ces précautions de sécurité et respecter tous les avertissements décrits ci-dessous. Installation 1. Pour un fonctionnement optimal, utiliser le projecteur dans une pièce sombre. 2. Placer le projecteur sur une surface à niveau et dans un endroit sec exempt de poussières et d'humidité. 3. Ne pas placer le projecteur en plein soleil, près d'appareils ménagers ou d'autres appareils de chauffage. DOC avis de conformation DOC avis de conformation Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur le Matériel Brouilleur du Canada. 6 7 4. La fumée, la vapeur et l'exposition aux rayons directs du soleil risquent de détériorer sérieusement les composantes internes. 5. Eviter des manipulations brusques lors du déplacement du projecteur, car un choc violent pourrait endommager les composantes internes. 6. Ne pas deposer d'objets lourds sur le dessus du projecteur. 7. Lors de l'installation du projecteur au plafond, respecter les instructions suivantes. a. Le plafond doit être suffisamment solide pour supporter le poids du projecteur et il doit être installé selon les codes de construction locaux. b. Le projecteur doit être installé par un personnel qualifié. 3. Si le projecteur n'est pas utilisé pendant une période prolongée, retirer la fiche de la prise secteur. Nettoyage 1. Débrancher le projecteur de la prise d'alimentation avant le nettoyage. 2. Nettoyer régulièrement le coffret avec un chiffon doux. S'il y a des taches tenaces, utiliser une solution d'un détergent doux. Ne jamais utiliser de détergents puissants ou des solvants, tel que l'alcool ou un diluant pour nettoyer le projecteur. 3. Utiliser un appareil diffuseur chauffant ou du papier de nettoyage de lentille disponible dans le commerce pour nettoyer la lentille. Ne pas frapper ou rayer la surface de la lentille, car des défauts risquent de se produire sur la surface de la lentille. Alimentation 1. Le projecteur est conçu pour fonctionner à 100-120 ou 220-240VCA 50/ 60Hz. S'assurer que la tension d'alimentation locale satisfait cette exigence avant d'utiliser le projecteur. 2. Manipuler le câble d'alimentation avec précaution et éviter de le plier excessivement. Un cordon endommagé risque de provoquer une électrocution ou un incendie. Remplacement de la lampe · Effectuer le remplacement de la lampe suivant les instructions de la page 81. · Assurez-vous de bien remplacer la lampe lorsque le voyant d'usure s'allume. Si vous continuez d'utiliser la lampe après 1000 heures d'utilisation, l'ampoule peut se briser et des brisures de verre peuvent être éparpillées dans le compartiment de la lampe. Ne les touchez pas car elles peuvent vous blesser. Dans ce cas, contactez votre revendeur NEC afin de procéder au remplacement de la lampe. · Attendez minimum UNE minute après avoir éteint la lampe avant de la rallumer. Une haute tension est immédiatement appliquée à la lampe quand celle-ci est mise sous tension. Par conséquent, éteindre, puis tout de suite rallumer peut abréger la vie de votre lampe et endommager votre projecteur. 2. Eviter que des objets étrangers, des agrafes, des clous et du papier, par exemple, pénètrent à l'intérieur du projecteur. Ne pas essayer de récupérer ces objets soi-même ou ne pas insérer des objets métalliques, des fils et des tourne-vis, par exemple à l'intérieur du projecteur. Si un objet tombe à l'intérieur du projecteur, le débrancher immédiatement et contacter un dépanneur qualifié pour retirer l'objet. 3. Ne pas placer des liquides sur le dessus du projecteur. · Ne regardez pas à l'intérieur de l'objectif lorsque le projecteur est en marche. Vous risquez de vous blesser gravement aux yeux. · Ne regardez pas à l'intérieur de la flèche laser lorsque celle-ci est en marche et ne dirigez pas le rayon laser sur une autre personne. Vous risquez de provoquer ue blessure grave. Précautions pour éviter un incendie ou une électrocution 1. Une ventilation appropriée doit être assurée afin d'éviter une accumulation de chaleur à l'intérieur du projecteur. S'assurer que les trous de ventilation ne sont pas obstrués. Laisser un espace d'au moins 10 cm (quatre pouces) entre le projecteur et les murs. 8 LIMITED ® WARRANTY 9 NEC MultiSync Projector Products NEC Technologies, Inc. (hereafter NECTECH) warrants this product to be free from defects in material and workmanship under the following terms. 2. Any product on which the serial number has been defaced, modified or removed. NECTECH'S LIABILITY FOR ANY DEFECTIVE PRODUCT IS LIMITED TO THE REPAIR OR REPLACEMENT OF THE PRODUCT AT OUR OPTION. REPLACEMENT PRODUCTS MAY BE NEW OR `LIKE NEW'. 3. NECTECH SHALL NOT BE LIABLE FOR : Damage, deterioration or malfunction resulting from: a. Accident, misuse, abuse, neglect, fire, water, lightning or other acts of nature, unauthorized product modification, or failure to follow instructions supplied with the product. b. Repair or attempted repair by anyone not authorized by NECTECH. c. Any shipment of the product (claims must be presented to the carrier). d. Removal or installation of the product. e. Any other cause which does not relate to a product defect. 4. Cartons, carrying cases, batteries, external cabinets, magnetic tapes, or any accessories used in connection with the product. HOW LONG IS THE WARRANTY? Parts and labor are warranted for (2) two years from the date of the first customer purchase. The lamp is warranted for 1000 hours of operating time or six months, whichever comes first. WHO IS PROTECTED? This warranty may be enforced only by the first purchaser. WHAT IS COVERED AND WHAT IS NOT COVERED Except as specified below, this warranty covers all defects in material or workmanship in this product. The following are not covered by the warranty: 1. Any product which is not distributed in the U.S.A. or Canada by NECTECH or which is not purchased in the U.S.A. or Canada from an authorized NECTECH dealer. For a listing of authorized dealers please contact NECTECH at 800-836-0655. WHAT NEC WILL COVER We will pay labor and material expenses for covered items. But we will not pay for the following: 1. Removal or installation charges. 2. Costs of initial technical adjustments (set-up), including adjustment of user controls. These costs are the responsibility of the NECTECH dealer from whom the product was purchased. 3. Payment of shipping charges. 1. DAMAGE TO OTHER PROPERTY CAUSED BY ANY DEFECTS IN THIS PRODUCT, DAMAGES BASED UPON INCONVENIENCE, LOSS OF USE OF THE PRODUCT, LOSS OF TIME, COMMERCIAL LOSS; OR 2. ANY OTHER DAMAGES, WHETHER INCIDENTAL, CONSEQUENTIAL OR OTHERWISE. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS AND/OR DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS AND EXCLUSIONS MAY NOT APPLY TO YOU. HOW YOU CAN GET WARRANTY SERVICE 1. To obtain service on your product, consult the dealer from whom you purchased the product. 2. Whenever warranty service is required, the original dated invoice (or a copy) must be presented as proof of warranty coverage. Please be prepared to describe or demonstrate the problem to your dealer. 3. For the name of the nearest NECTECH authorized service center, call NECTECH at 800-836-0655. HOW STATE LAW RELATES TO THE WARRANTY This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. FOR MORE INFORMATION, TELEPHONE 800-366-5213 NEC TECHNOLOGIES, INC. 1250 N. Arlington Heights Road, Suite 500 Itasca, Illinois 60143-1248 NOTE: All products returned to NECTECH for service MUST have prior approval. To get approval, call NEC Technologies at 800-836-0655. LIMITATION OF IMPLIED WARRANTIES ALL IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO THE LENGTH OF THIS WARRANTY. EXCLUSION OF DAMAGES NECTECH'S LIABILITY FOR ANY DEFECTIVE PRODUCT IS LIMITED TO THE REPAIR OR REPLACEMENT OF THE PRODUCT AT OUR OPTION. NECTECH SHALL NOT BE LIABLE FOR: 10 TABLE 1. Introduction OF CONTENTS 11 Introduction To The MultiSync LT100 Projector ............................................................ 13 How Do You Get Started? ............................................................................................... 15 What's In The Box? ........................................................................................................ 15 Getting To Know Your MultiSync LT100 Projector ........................................................ 17 Front Features .......................................................................................................... 17 Rear Features ........................................................................................................... 18 Top Features ............................................................................................................ 19 Terminal Panel Features ........................................................................................... 21 Remote Control Features ......................................................................................... 25 2. Installation Setting Up Your MultiSync LT100 Projector ................................................................... 29 Selecting A Location ................................................................................................ 30 Projection Distance .................................................................................................. 31 Using A Tabletop Or Cart ........................................................................................ 35 Transporting And Storing The Projector .................................................................. 37 Ceiling Installation ................................................................................................... 39 Wiring Diagram ........................................................................................................ 41­42 Connecting Your PC Or Macintosh Computer ................................................................ 43 Connecting Your DVD Player ......................................................................................... 49 Connecting Your Document Camera ............................................................................... 49 Connecting Your VCR Or Laser Disc Player ................................................................... 50 Connecting An External Monitor .................................................................................... 50 Connecting Your Remote Mouse Receiver ...................................................................... 51 3. Operation General Controls ............................................................................................................. 55 Using The Menus ............................................................................................................ 57 Menu Descriptions & Functions ..................................................................................... 59 Source Menu (Source Icons) .................................................................................... 59 Image Adjust Menu(Sound And Picture Control Icons) ........................................... 61 Power Menu(Projector Control Icons) .................................................................... 65 Settings Menu(Maintenance Icons) .......................................................................... 67 Using the Viewer Function ....................................................................................... 69 4. Maintenance Replacing The Lamp ....................................................................................................... 77 Remote Control Battery Installation ................................................................................ 79 Operating Range ............................................................................................................. 80 5. Troubleshooting Status Light Messages ..................................................................................................... 85 Common Problems & Solutions ...................................................................................... 87 6. Specifications Optical ............................................................................................................................ 89 Electrical ......................................................................................................................... 90 Mechanical ..................................................................................................................... 90 D-Sub Pin Assignments .................................................................................................. 93 Timing Chart ................................................................................................................... 95 PC Control Command Reference .................................................................................... 97 Cable Connection .......................................................................................................... 101 12 1 INTRODUCTION This section introduces you to your new MultiSync LT100 (XGA) Projector, provides a list of materials that comes with your projector and describes the features and controls. Congratulations On Your Purchase Of The MultiSync LT100 Projector The MultiSync LT100 is one of the very best projectors available today. The MultiSync LT100 enables you to project precise images up to 300 inches across (measured diagonally) from your PC or Macintosh computer (desktop or notebook), VCR, DVD player, document camera, or even a laser disc player. You can use the projector on a tabletop or cart, you can permanently mount it on a ceiling*1, or you can use MultiSync LT100 Projector to project images from behind the screen. The remote control can be used wirelessly or with a cable, and you can even use the remote control with the built-in remote mouse receiver to operate the mouse on your PC or Mac. 13 Features you'll enjoy: · Simple set up and operation. · A high-performance 280 watt metal halide lamp that delivers a high bright image, allowing you to make presentations with the lights on. · A wireless remote control that operates the projector from any angle. · A laser pointer that' s built into the remote control. · The manual zoom control enables you to adjust the image to be between 24 and 300 inches (measured diagonally). · White balance control allows you to adjust the brightness and contrast for each RGB color. · You can choose between video modes depending on your source: "normal" for a typical picture, "natural" for true color reproduction, and "camera" for use with a document camera or low APL picture. · The optional LT Viewer kit allows you to start your presentation even when a PC is not available at the site. · The "image capture" enables you to use the entire picture as a background image or to create slides (optional LT Viewer required). · An image can be projected from in front or behind a screen, and the projector can even be installed on the ceiling. · NEC Technologies' exclusive AccuBlendTM intelligent pixel blending technology - an extremely accurate image compression technology - offers a crisp image with SXGA (1280 1024) resolution*2 . · Supports most IBM VGA, SVGA, XGA, SXGA(with AccuBlendTM)*2 , Macintosh, or any other RGB signals within a horizontal frequency range of 15.754 to 85 kHz and a vertical frequency range of 50 to 85 Hz. This includes NTSC, PAL, SECAM and NTSC4.43 standard video signals. Note: Composite video standards are as follows: NTSC: U.S. TV standard for video in U.S. and Canada. PAL: TV standard used in western Europe. SECAM: TV standard used in France and Eastern Europe. NTSC4.43: TV standard used in Middle East countries. · Accepts component video source such as DVD player with the Y/ Cb/Cr output. · The remote control can be used with or without a cable, and you can even use the remote to operate your PC or Macintosh mouse wirelessly from across the room with the built-in remote mouse receiver. · You can control your MultiSync LT100 Projector with a PC. · The contemporary cabinet design is compact, easy to carry, and complements any office, board room or auditorium. *1 Installing the MultiSync LT100 LCD Projector on the ceiling must be done by authorized NEC technicians. Consult your NEC dealer for more information. 2 * An SXGA image (1280 1024) is converted into a 1024 768 crisp image with NEC technology's AccuBlend. INTRODUCTION 14 15 How Do You Get Started? The fastest way to get started is to take your time and do everything right the first time. Take a few minutes now to click through the training CD-ROM and review the user's manual. This may save you hours later on. At the beginning of each section of the manual you'll find an overview. If the section doesn't apply, you can skip it. Remote control Mouse adapter (For IBM PS/2) What's In The Box? Make sure your box contains everything listed. If any pieces are missing, contact your dealer. Please save the original box and packing materials if you ever need to ship your MultiSync LT100 Projector. · NEC MultiSync LT100 Projector · Carrying Case · Remote Control With Built-In Laser Pointer · Remote Control Case · Remote Mouse Receiver · Signal Cable (15-Pin Mini D-Sub To 15-Pin Mini D-Sub Connector) · · · · · · · · · Mouse Adapters for IBM PS/2 and Mac Serial Cable Pin Adapter for Macintosh Power Cable Two AA Batteries Introductory / Training CD-ROM User's Manual Registration Card Quick Connect Guide Remote control case Mouse adapter (For Macintosh) Remote mouse receiver Batteries (AA 2) Pin adapter for Macintosh Power cable Signal cable (15-Pin Mini D-Sub To 15-Pin Mini D-Sub connector) Serial cable Carrying case Introductory / Training CD-ROM User's manual Registration card Quick Connect Guide Qu 1 LT cr no y ct iS je lt o u Pr M k ic c n y iS lt u M 1 LT 0 0 Co tG ec nn id e 0 0 INTRODUCTION 16 17 Getting To Know Your MultiSync LT100 Projector Front Features P O W E R S TA C T S E LE M E M U TU S Top features Monaural Speaker (1W) O N /O FF E N TE R Cooling Fan Remote Sensor Ventilation One-Touch Tilt Button Rear Foot Adjustable Foot Lens and lens Cap Focus Ring Zoom Ring Lever One-Touch Tilt Button Terminal Panel Remote Sensor Adjustable Foot Rear Features Remote Sensor Remote Sensor M E M U C T TU S TA S E N TE R P O W E R LE S E Slot for Kensington MicroSaver Security System AC IN O N /O FF Carrying handle Power Switch AC Input Connect the supplied power cable's three-pin plug here. INTRODUCTION 18 19 Top Features 1 Power Button Use this button to turn the power on and off when Main Power Switch is on and the projector is on standby. 2 Enter Button Executes your menu selection. 3 Select (vw ) / (+)(­) Buttons Select: After you press the "Menu" button, use the v or w button to (vw ) select the menu icon of the item you wish to adjust. (+)(­): Use these buttons while you' re in the Image Adjust mode to change the level of a selected menu item. These buttons are also used to set an item in the Power or Settings menus. 4 Menu Button Displays the on- screen menu. 5 Power Indicator When the projector is switched On, the green LED blinks for about one minute, then lights up. M E M U C T LE E TA S E N TE R O N /O FF TU S S P O W E R AC IN 4 If the main power is on and you switch it off by pressing POWER OFF on the remote control or press and hold down the POWER button on the cabinet for one second, the green LED blinks for one minute, then lights up and the projector goes on standby. * The projector will not accept operation instructions for the one minute during which the LED is blinking during switching on or off as described above. 6 Status Indicator When this is lit red continually, it's warning you that the projection lamp has exceed 1000 hours of service. After this light appears, it is advisable to replace the projection lamp as soon as possible.(See page 77.) When the operating time of the lamp exceeds 1000 hours, the STATUS indicator is lit red continually. In addition the message "LAMP USAGE XX HOURS" appears continually when the on-screen menu is not displayed. If this light blinks red rapidly, it indicates that the lamp house is not attached properly; if the light blinks slowly it means the projector's internal temperature is too hot to operate safely. See the Status Light Messages on page 85 for more details. INTRODUCTION MENU SELECT - + 3 2 ENTER 6 STATUS ON / OFF POWER 5 1 20 21 Terminal Panel Features This panel is located in the side and is where you connect your cables. 1 2 3 1 Remote Control Jacks a. Remote Control Input Jack Connect your remote control cable here for wired operation. b. Remote Control Output Jack This terminal enables you to operate up to five projectors with the same remote control. When your remote mouse receiver is connected here, the remote sensors on the projector cabinet will receive your mouse commands. 2 Video Input Connect a VCR, laser disk player, or document camera here to project video. Left Channel/Mono Audio Input Jack This is your left channel audio input for stereo sound coming from video equipment or audio system. This also serves as your monaural audio input. Right Channel Audio Input Jack This is your right channel audio input for stereo sound. INTPUT VIDEO INPUT PC CONTROL OUTPUT S-VIDEO VIDEO L(MONO) -R-AUDIO RGB INPUT RGB OUTPUT REMOTE CONTROL RGB AUDIO RGB AUDIO 4 S-Video Input Here is where you connect S-Video input from an external source like a VCR. NOTE: S-Video provides more vivid color and higher resolution than the traditional composite video format. 3 PC Control Port Use this port to connect your PC to control the MultiSync LT100 Projector. This enables you to use your PC and serial communication protcol to control the projector. If you are writing your own program, command reference are on pages 97 to 100. 4 RGB Input Connector (Mini D-Sub 15 pin) Connect your PC or other RGB equipment such as IBM or compatible computers. Use the signal cable that's supplied to connect to a PC. This also serves as the Y/Cb/Cr input connector which allows you to connect a DVD player with the component video output. RGB Audio Input Mini Jack This is where you connect RGB audio output from a computer or another RGB source. INTRODUCTION 22 23 5 RGB Output Connector (Mini D-Sub 15 pin) You can use this connector to loop your computer image to an external monitor from the RGB input source. Even if VIDEO is selected, the video image input to the RGB INPUT terminal is output. Audio Output Mini Jack You can use this jack to loop your audio to an external monitor from the VIDEO audio input or RGB audio input source. 6 Built-in Security Slot ( ) This security slot supports the MicroSaver® Security System. MicroSaver® is a registered trademark of Kensington Microware Inc. The logo is trademarked and owned by Kensington Microware Inc. M E M U C T TU S INTPUT VIDEO INPUT PC CONTROL OUTPUT S-VIDEO VIDEO L(MONO) -R-AUDIO RGB INPUT RGB OUTPUT REMOTE CONTROL RGB AUDIO RGB AUDIO 5 E LE TA S R P O S W E R 6 AC IN E N TE INTRODUCTION O N /O FF 24 25 Remote Control Features You can use your wireless remote control to operate your MultiSync LT100 Projector. With the remote mouse receiver connected to your computer, you can also use the projector's remote control to operate your computer. (See pages 51 and 54 to connect the remote mouse receiver to your computer.) 2 NOTE: If you are using a Macintosh computer, you can click either the right or left button to activate the mouse. 3 1 1 Left Click Button Use this button to enter your menu selection. It works the same as the "Enter" button on the cabinet. 2 Laser Pointer Beams a laser light when "Laser" button is pressed. 3 Infrared Transmitter Direct the remote control toward the remote sensor on the projector cabinet 6 or the remote mouse receiver. 7 4 LED Flashes when any button is pressed. 8 MENU LASER OFF POWER ON 4 5 VIDEO S-VIDEO RGB PC CARD 9 10 - + 5 Power On And Off If your main power switch is turned on, you can use these buttons to turn your MultiSync LT100 Projector on and off. 6 Video Button Press to select an NTSC, PAL, SECAM or NTSC4.43 compatible video source from a VCR, DVD player, laser disc player or document camera. 7 S-Video Button Press to select an S-Video source from a VCR or other S-Video source. 8 RGB Button Press to select a video source from a computer connected to your RGB port. 9 PC Card Button Press to display a slide from the flash memory card inserted in the PC card slot of your projector. (You must first install the optional LT Viewer board into your projector.) 10 Menu Button Use this button to call up the On-Screen Menu so you can adjust and set the image. After you press this button, it will light up. During this time you can use the mouse pointer and right/left click buttons to make menu selections. If no buttons are pressed within 10 seconds the menu turns off. INTRODUCTION 26 R-CLICK POSITION PIC-MUTE FREEZE MAGNIFY SLIDE VOLUME + - + - + - 27 11 Laser Button Press and hold this button to activate the laser pointer. When lit, you can use the laser to draw your audience's attention to a red dot that you can place on any object within 30 feet (10 m). 12 Mouse Pointer Buttons Works as a mouse for your computer. This button is also used to adjust screen position. Push (+) or (­) to select the submenu you want to adjust. 13 Right Click Button Press this button to exit "Menus" or "Position." 14 Freeze Button This button will freeze a video image. Press again to resume motion. 15 Position Button When image is magnified, press this button to activate the mouse. This allows you to select the portion of the image displayed on screen. Position button will remain lit for 10 seconds or until right click button is pushed. NOTE: When you are adjusting Position, the Mouse Pointer button is used to move the picture. OFF POWER ON VIDEO S-VIDEO RGB PC CARD MENU LASER 11 + 12 13 R-CLICK POSITION PIC-MUTE FREEZE 16 Picture Mute Button This button turns off the image for a short period of time. Press again to restore the image. 15 MAGNIFY SLIDE VOLUME 14 16 + - + - + - 17 Magnify Button Use the (+) or (­) button to adjust the image size up to 400%. 18 Slide Button Press (+) to advance the next file or slide and (-) to return to the 17 previous file or slide. (the optional LT Viewer board required) 19 Volume Buttons Press (+) to increase the volume and (­) to decrease it. 20 Remote Jack Connect your remote control cable here for wired operation. VI O DE 19 18 O F NOTE: You cannot use Menu and Position at the same time. - S- RG B VI M EN U PC CA RD Remote Control Precautions · Do not look into the laser pointer while it is on. · Do not point the laser beam at a person. · Handle the remote control carefully. · If the remote control gets wet, wipe it dry immediately. · Avoid excessive heat and humidity. · If you will not be using the remote control for a long time, remove the batteries. · Do not mix new and old or different types of batteries. INTRODUCTION LA SE R ON TI SI PO FY NI AG M+ E ID SL + K RE CF LI TE -C U R IC-M P E EZ - + E M LU VO + - 20 28 2 INSTALLATION This section describes how to set up your MultiSync LT100 projector and how to connect video and audio sources. 29 Setting Up Your MultiSync LT100 Projector Your MultiSync LT100 Projector is simple to set up and use. But before you get started, you must first: 1. Determine the image size 2. Set up a screen or select a non-glossy white wall onto which you can project your image. Carrying The Projector Always carry your projector by the handle. Ensure that the power cord and any other cables connecting to video sources are disconnected before moving the projector. When moving the projector or when it is not in use, cover the lens with the lens cap. M E M U C T E TA S E N TE R O N /O FF TU S LE S AC IN Carrying handle Pull it out ; push it back to retract. Diagonal Image Size (inch) Selecting A Location The further your projector is from the screen or wall, the larger the image. The minimum size the image can be is approximately 24" (0.61 m) measured diagonally when the projector is roughly 4 feet (1.2 m) from the wall or screen. The largest the image can be is 300" (7.6 m) when the projector is about 40.35 feet (12.3 m) from the wall or screen. Projection Distance and Image Size P O W E R 300 300" 240 200 160 120 100 80 60 40 20 0 0.0 231" WIDE TELE 27" 24" 3.28 (1) 6.56 (2) 9.84 13.12 16.4 (3) (4) (5) 19.7 (6) 23.0 (7) 26.2 (8) 29.5 (9) 32.8 (10) 36.1 (11) 39.4 40.35 ft. (12) (12.3) (m) Projection distance Width Projection Distance Height Screen size (diagonal) INSTALLATION 30 31 Projection Distance Wide Screen size Projection angle Screen width H inch Degree inch mm A inch mm B inch mm Projection distance C inch mm D inch mm E inch mm 40" 14.8 32 813 65.2 1655 4.7 119 63 1600 12 305 24 610 60" 14.8 48 1219 97.8 2483 7.0 178 94.5 2400 18 457 36 914 70" 14.7 56 1422 114.8 2915 8.2 207 111 2819 21 533 42 1067 80" 14.7 64 1626 131.6 3342 9.3 237 127.3 3233 24 610 48 1219 90" 14.6 72 1829 148.3 3767 10.5 267 143.5 3645 27 686 54 1372 100" 14.6 80 2032 164.8 4185 11.7 296 159.4 4049 30 762 60 1524 120" 14.6 96 2438 198.5 5042 14.0 356 192.1 4879 36 914 72 1829 150" 14.6 120 3048 248.7 6316 17.5 444 240.7 6114 45 1143 90 2286 180" 14.5 144 3658 298.9 7591 21.0 533 289.3 7348 54 1372 108 2743 200" 14.5 160 4064 332.3 8441 23.3 593 321.7 8171 60 1524 120 3048 240" 14.5 192 4877 399.2 10140 28.0 711 386.5 9817 72 1829 144 3658 270" 14.5 216 5486 449.4 11415 31.5 800 435.1 11052 81 2057 162 4115 300" 14.5 240 6096 500.2 12704 35.0 889 484.3 12301 90 2286 180 4572 Tele Screen size Projection angle Screen width H inch Degree inch mm A inch mm B inch mm Projection distance C inch mm D inch mm E inch mm 40" 11.4 32 813 84.4 2143 4.7 119 82.7 2101 12 305 24 610 60" 11.4 48 1219 126.5 3213 7.0 178 124 3150 18 457 36 914 70" 11.4 56 1422 147.2 3739 8.2 207 144.3 3665 21 533 42 1067 80" 11.4 64 1626 168.7 4286 9.3 237 165.4 4201 24 610 48 1219 90" 11.3 72 1829 190.8 4847 10.5 267 187.1 4752 27 686 54 1372 100" 11.3 80 2032 212.8 5406 11.7 296 208.7 5301 30 762 60 1524 120" 11.3 96 2438 255.2 6483 14.0 356 250.3 6358 36 914 72 1829 150" 11.3 120 3048 319.6 8117 17.5 444 313.4 7960 45 1143 90 2286 180" 11.3 144 3658 384.0 9753 21.0 533 376.6 9566 54 1372 108 2743 200" 11.3 160 4064 426.3 10829 23.3 593 418.1 10620 60 1524 120 3048 240" 11.2 192 4877 512.7 13024 28.0 711 502.9 12774 72 1829 144 3658 270" 11.2 216 5486 577.2 14660 31.5 800 566.1 14379 81 2057 162 4115 300" ­ ­ ­ ­ ­ ­ ­ ­ ­ ­ ­ ­ ­ * For Screen Sizes of 24 to 300 inches not indicated on the projection tables, use the formulas on the next page. INSTALLATION 32 33 Desk top Screen C Unit (inch) H (inch) = Width of screen A = C / cos B = 3.7H / 25.4 C (WIDE) = (2.026 H) ­ 2.437 C (TELE) = C (WIDE) 1.3 D=E/2 E=H/4 3 E A Screen bottom B 3.8" (96.64mm) Screen center D Projector base Unit (mm) H (inch) = Width of screen A = C / cos B = 3.7H C (WIDE) ={(2.026 H) ­ 2.437} C (TELE) = C (WIDE) 1.3 D=E/2 E=H/4 3 25.4 Ceiling mount C Projector base A Screen top D E Screen center 3.8" (96.64mm) B A : Distance between lens center and screen center B : Vertical distance between lens center and screen bottom (screen top for ceiling mount) C : Horizontal throw distance between screen surface and projector lens D : Vertical distance between screen center and screen bottom (screen top for ceiling mount) E : Screen Height INSTALLATION 34 35 Using A Tabletop Or Cart 1. Place your projector on a flat level surface at the optimal distance from the screen or wall so you realize the size image you want. (Avoid having bright room lighting or sun light directly on the screen or wall where you'll be projecting the image.) 2. Connect the power cable, remove the lens cap and turn the projector on. (If no input signal is available, the projector will display a background image.) 3. Ensure that the projector is square to the screen. 4. Move the projector left or right to center the image horizontally on the screen. (A) 5. To center the image vertically (B), lift the front edge of the projector and press the buttons on the front of the projector, just above the feet, to release the one-touch tilt feet. (There is approximately 5.0° of up and down adjustment for the front of the projector. (A) Top view screen (B) Side view screen 6. To fine tune the image's position vertically on the screen, rotate each front foot, and rear feet if necessory. NOTE: Adjust feet so that lens surface is parallel to the screen. If you use the projector with the screen tilted, the picture will be distorted. 7. Adjust the size of the image using the zoom ring lever on the lens. NOTE: The set up angle of the projector should not exceed 15 degrees, otherwise lamp life could decrease dramatically. Up Down Up Down Focus ring Zoom ring lever INSTALLATION 36 37 Transporting and storing the projector A padded carrying case has been supplied with your projector. Please use this case when transporting and storing the projector. The carrying case also has a compartment for your laptop computer. To use the carrying case follow the directions below: 1. Unfold carrying case. 3. Hold the projector by it's handle and slide it into the large compartment of the carrying case. Projector MEMU SELECT AC IN ENTER ON / OFF STATUS POWER 2. Zip up the sides of the case. 4. Zip up the top of the case. Zipper 5. Unlatch the belt and then place your notebook computer into the front pouch. Note book PC 7. Store the remote control and other accessories in the side pouches on the carrying case. 1 2 Other Accessories 6. Latch the belt. When storing the remote control, place the remote in its protective case. The case will keep the remote buttons from being accidentally pushed while it is being stored or transported. This will keep the batteries from being discharged. 2 1 * Carry the projector carefully. Bumping or dropping the projector may cause damage. INSTALLATION 38