NEC Flat Professional Series MultiSync FP950 FP1350 TM TM TM TM ® ® User's Manual User's Manual 78134171 1 12/3/98, 4:09 PM Index Warning Contents Quick Start Controls Recommended Use Specifications Features Troubleshooting References Limited Warranty TCO'99 Avertissement Contenu Mise en marche rapide Commandes Usage recommandé Fiche technique Fonctions Dépannage Références Garantie limitée TCO'99 Warnung Lieferumfang Quick Start Bedienungselemente Empfehlungen für die Verwendung Technische Daten Funktionen Fehlerbehebung Verweise Beschränkte Gewährleistung TCO'99 1 2 3-5 6-9 10-11 12-13 14 15 16 17 18-19 21 22 23-25 26-29 30-31 32-33 34 35 36 37 38-39 42 43 44-46 47-50 51-52 53-54 55 56 57 58 59-60 78134171 2 12/3/98, 4:09 PM WARNING TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT USE THIS UNIT'S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS THE PRONGS CAN BE FULLY INSERTED. REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. CAUTION CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, MAKE SURE POWER CORD IS UNPLUGGED FROM WALL SOCKET. TO FULLY DISENGAGE THE POWER TO THE UNIT, PLEASE DISCONNECT THE POWER CORD FROM THE AC OUTLET. DO NOT REMOVE COVER (OR BACK) NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol warns user that uninsulated voltage within the unit may have sufficient magnitude to cause electric shock. Therefore, it is dangerous to make any kind of contact with any part inside this unit. This symbol alerts the user that important literature concerning the operation and maintenance of this unit has been included. Therefore, it should be read carefully in order to avoid any problems. Canadian Department of Communications Compliance Statement DOC: This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. C-UL: Bears the C-UL Mark and is in compliance with Canadian Safety Regulations according to C.S.A. 22.2 #950. FCC Information 1. Use the attached specified cables with the JC-1946UMW and JC-2241UMW color monitors so as not to interfere with radio and television reception. (1) Please use the supplied power cord and USB cable or equivalent to ensure FCC compliance. (2) Shielded signal cable. Use of other cables and adapters may cause interference with radio and television reception. 2. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. · Consult your dealer or an experienced radio/TV technician for help. If necessary, the user should contact the dealer or an experienced radio/television technician for additional suggestions. The user may find the following booklet, prepared by the Federal Communications Commission, helpful: "How to Identify and Resolve Radio-TV Interference Problems." This booklet is available from the U.S. Government Printing Office, Washington, D.C., 20402, Stock No. 004-000-00345-4. 1 78134171 3 12/3/98, 4:09 PM Contents Your new NEC Technologies MultiSync® FP Series monitor box* should contain the following: · MultiSync FP Series Monitor with tilt/swivel base MultiSync FP950TM (JC-1946UMW) or MultiSync FP1350TM (JC-2241UMW) · Power Cord · Signal Cable · USB Cable · Monitor Control Software · Macintosh Cable Adapter · User's Manual · Registration Card Power Cord Macintosh Cable Adapter Monitor Control Software USB Cable AT IO N NE C Signal Cable User's Manual Registration Card * Remember to save your original box and packing material to transport or ship the monitor. 2 PR se r's Ma nu al O D U 78134171 4 C Mu l FP tiSy 95 nc FP 0 1 U 35 0 ® ® n u p ult By iSy ome ovat ort y ing da ret ef o nc nts ive an te o urni p u, a for mo to nit reg rodu nd t ts to ab d se f pu ng t or. iste cts o b esp ility rial n rchas his c r y , pl rin eci to p um e a ard pu ou eas g , n rch ally ro rn e ces bers. d rec we c ew ase i Th is l f you s wa This ords onfir an ank m ost r o rra NE yo rig nty facil the m you . it ina C M u fo o l p claim ates del r ry ult ou roo iSy our r f o s, nc tim f mo e a nit nd or. for ch oo sin g T Note: You can register your product on the Internet at http://www.prodreg.com/nec R EG IS T Fla tP ro fe ss io na lS er ie s TH C M M CHO AN ultiSy ul tiS OS K Y nc Mon ito yn ING O c © A U F rs To be hel -- MNO Im ON N R yo tter s p us po u n er ta rta v in o IT EC e NE ke a w an e an ur c nt OR C M few d i d su ont -- in p mn NE R 12/3/98, 4:09 PM Quick Start To attach the MultiSync® FP Series monitor to your system, follow these instructions: 1. Turn off the power to your computer. If you are using the signal cable, continue to Step 2. If you are using a BNC cable, please skip to Step 3. NOTE: BNC cables may be purchased at your local electronics store. 2. For the PC: Connect one end of the 15-pin mini D-SUB signal cable to the connector of the display card in your system (Figure A.1) and the other end to the back of the monitor (Figure A.2). Tighten all screws. For the Mac: Connect the Macintosh cable adapter to the computer (Figure B.1). Attach one end of the 15-pin mini D-SUB signal cable to the Macintosh cable adapter (Figure B.1) and the other end to the back of the monitor (Figure B.2). Tighten all screws. Proceed to Step 4. 3. Connect the BNC cable to the appropriate connectors on the back of the monitor. Connect the red BNC cable to the BNC connector on the monitor labeled R, the green BNC cable to the BNC connector labeled G (/Sync), the blue BNC cable to the BNC connector labeled B. If you have a fourth BNC connector (Composite Sync), connect it to the BNC connector on the monitor labeled HS/CS. If you have a fifth BNC connector (Vertical Sync), connect it to the BNC connector on the monitor labeled VS (Figure C.1). NOTE: Incorrect cable connections may result in irregular operation or damage display components. Figure A.1 Figure B.1 3 78134171 5 12/3/98, 4:09 PM Quick Start cont.Start 4. Connect one end of the power cord to the MultiSync® FP Series monitor and the other end to the power outlet (Figure D.1). 5. Turn on the monitor (Figure E.1) and the computer. 6. The Factory Setting for your monitor is set for D-SUB installation. If you are using a BNC cable connection, push the BNC/D-SUB button on the front of the monitor (Figure E.1) to switch settings. Figure A.2 R G(/Sync) B Figure B.2 HS/CS VS Power Outlet BNC Connector Power Cord Figure C.1 Figure D.1 NOTE: For download information on the Windows®95/98 INF file for your MultiSync FP Series monitor, refer to the References section of this user's manual. NOTE: If you have any problems, please refer to the Troubleshooting section of this User's Manual. BNC/D-SUB Power Button MultiSync EXIT PROCEED RESET BNC/D-SUB Figure E.1 4 78134171 6 12/3/98, 4:10 PM Quick Start cont.Start If your computer is equipped with USB and uses the Windows® 98 operating system and you want to operate the monitor's user controls using your system, you can install USB support by using the following procedure. To attach the USB port on your MultiSync FP Series monitor to a USB port on your system: 1. Using the supplied USB cable, connect the USB Series B connector end to the USB upstream port on the monitor (Figure 1). 2. Connect the other end of the supplied cable to the USB downstream port on the computer (or to a USB Hub attached to the computer (Figure 1). 3. Install the supplied Monitor Control Software. USB upstream port USB Series B connector end USB downstream port Figure 1 5 78134171 7 12/3/98, 4:10 PM Controls OSMTM (On-Screen Manager) control buttons on the front of the monitor function as follows: EXIT / Main Menu Exits the OSM menu. Moves the highlighted area up/down to select one of the controls. Moves the highlighted area left/right to select one of the controls. Has no function. Resets all the controls within the highlighted menu to the factory setting. Sub-Menu Exits to the OSM controls main menu. Moves the highlighted area up/down to select one of the controls. Moves the bar in the ­ or + direction to decrease or increase the adjustment. Only executes control or enters sub, sub-menu. Resets the highlighted control to the factory setting. ­/+ PROCEED RESET NOTE: When RESET is pressed in the main and sub-menu, a warning window will appear allowing you to cancel the reset function. When OSM controls are activated, icons are displayed at the top of the menu. If an arrow ( ) is displayed in a sub-menu, it indicates further choices are available. To enter a sub, sub-menu, press PROCEED. Brightness/Contrast Controls Brightness: Adjusts the overall image and background screen brightness. Contrast: Adjusts the image brightness in relation to the background. Degauss: Eliminates the buildup of stray magnetic fields which alter the correct scan of the electron beams and affect the purity of the screen colors, focus and convergence. When activated, your screen image will jump and waver a bit as the screen is demagnetized. Caution: Please allow a minimum of 20 minutes to elapse between uses of the Degauss Control. Size and Position Controls Auto Adjust: Automatically adjusts the horizontal and vertical size and position settings for applicable signal timings. Left/Right: Moves the image horizontally (left or right). Down/Up: Moves the image vertically (up or down). Narrow/Wide: Decreases or increases the horizontal size of the image. Short/Tall: Decreases or increases the vertical size of the image. 6 78134171 8 12/3/98, 4:10 PM Controls cont.Start Color Control/AccuColor® Control System Color presets 1 through 5 selects the desired color setting. The bar is replaced by the color setting choice from 1 to 5. Each color setting is adjusted at the factory to the stated Kelvin. If a setting is adjusted, the name of the setting will change from Kelvin to Custom. Red, Green, Blue: NEC's AccuColor Control System decreases or increases the monitor's red, green or blue color guns depending upon which is selected. The change in color will appear on screen and the direction (decrease or increase) will be shown by the bars. Geometry Controls Geometry Controls Menu The Geometry controls allow you to adjust the curvature or angle of the sides of your display. Sides In/Out (pincushion): Decreases or increases the curvature of the sides either inward or outward. Sides Left/Right (pincushion balance): Decreases or increases the curvature of the sides either to the left or right. Sides Tilt (parallelogram): Decreases or increases the tilt of the sides either to the left or right. Sides Align (trapezoidal): Decreases or increases the bottom of the screen to be the same as the top. Rotate (raster rotation): Rotates the entire display clockwise or counterclockwise. Tools 1 Moiré Canceler: Moiré is a wavy pattern which can sometimes appear on the screen. The pattern is repetitive and superimposed as rippled images. When running certain applications, the wavy pattern is more evident than in others. To reduce moiré, adjust the ON/Level by using the ­/+ CONTROL buttons. Basic Convergence: Aligns all three colors (R,G,B) to form a single color (white). The purpose of this control is to ensure that a white line drawn on the screen is as crisp and clear as possible. · Use the Horizontal control to adjust the alignment of the white lines in the up/down direction. · Use the Vertical control to adjust the alignment of the white lines in the left/right direction. Area Convergence: A small window will appear to indicate the area of adjustment -- Top Horizontal, Top Vertical, Bottom Horizontal or Bottom Vertical. Corner Correction: Allows you to adjust the geometry of the corners of your display -- Top, Top Balance, Bottom or Bottom Balance. 7 78134171 9 12/3/98, 4:10 PM Controls cont. Linearity: This selection allows you to adjust the spacing of the area on the screen. The purpose of this control is to en ...