NEC LCD Series MultiSync LCD1510 LCD1510V LCD2010 User's Manual TM TM TM ® You can register your t product online a / www.nectech.com on productregistrati 78133314.wpc 1 5/7/99, 4:13 PM Index Warning Contents Quick Start Controls Recommended Use Specifications Features Troubleshooting References Limited Warranty TCO'95 TCO'92 Avertissement Contenu Mise en marche rapide Commandes Usage recommandé Fiche technique Fonctions Guide de dépistage Références Garantie limitée TCO'95 TCO'92 Warnung Lieferumfang Quick Start Bedienungselemente Empfehlungen für die Verwendung Technische Daten Funktionen Fehlerbehebung Verweise Beschränkte Gewährleistung TCO'95 TCO'92 1 2 3-7 8-10 11-12 13-14 15 16 17 18 19-20 21 22 23 24-28 29-31 32-33 34-35 36 37 38 39 40-41 42 44 45 46-50 51-53 54-55 56-57 58 59 60 61 62-63 64 78133314.wpc 2 5/7/99, 4:13 PM WARNING TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT USE THIS UNIT'S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS THE PRONGS CAN BE FULLY INSERTED. REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. CAUTION CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, MAKE SURE POWER CORD IS UNPLUGGED FROM WALL SOCKET. TO FULLY DISENGAGE THE POWER TO THE UNIT, PLEASE DISCONNECT THE POWER CORD FROM THE AC OUTLET.DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol warns user that uninsulated voltage within the unit may have sufficient magnitude to cause electric shock. Therefore, it is dangerous to make any kind of contact with any part inside this unit. This symbol alerts the user that important literature concerning the operation and maintenance of this unit has been included. Therefore, it should be read carefully in order to avoid any problems. DOC: This Class B digital apparatus meets all requirements of the Canadian InterferenceCausing Equipment Regulations. C-UL: Bears the C-UL Mark and is in compliance with Canadian Safety Regulations according to C.S.A. C22.2 No. 950. Canadian Department of Communications Compliance Statement FCC Information 1. Use the attached specified cables with the LA-1521JMW, LA-1522JMW and LA-2032JMW color monitor so as not to interfere with radio and television reception. (1) Please use the supplied power cord or equivalent to ensure FCC compliance. (2) Please use the supplied AC Adapter. (3) MultiSync® LCD1510TM and LCD1510VTM monitor: Shielded video signal cable. (4) MultiSync® LCD2010TM monitor: Shielded 15-pin VGA to BNC cable. Use of other cables and adapters may cause interference with radio and television reception. 2. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. · Consult your dealer or an experienced radio/TV technician for help. If necessary, the user should contact the dealer or an experienced radio/television technician for additional suggestions. The user may find the following booklet, prepared by the Federal Communications Commission, helpful: "How to Identify and Resolve Radio-TV Interference Problems." This booklet is available from the U.S. Government Printing Office, Washington, D.C., 20402, Stock No. 004-000-00345-4. 1 78133314.wpc 3 5/7/99, 4:13 PM Contents You can register your product online at www.nectech.com/productregistration Your new NEC Technologies MultiSync® LCD monitor box* should contain the following: Model Name Standard Model Number MultiSync® LCD1510TM · MultiSync LCD Monitor with tilt/swivel/pivot stand MultiSync® LCD1510VTM · Power Cord MultiSync® LCD2010TM · AC Adapter · Video Signal Cable (LCD1510, LCD1510V) · 15-pin VGA to BNC Cable (LCD2010) · User's Manual · Pivot® Driver Software CD LA-1521JMW LA-1522JMW LA-2032JMW MultiSync LCD2010 monitor with 15-pin VGA to BNC Cable and AC Adapter MultiSync LCD1510/LCD1510V monitor with Video Signal Cable and AC Adapter Power Cord User's Manual (Includes User's Manual) Pivot Driver Software CD * Remember to save your original box and packing material to transport or ship the monitor. 2 78133314.wpc 4 5/7/99, 4:13 PM Quick Start 1. Turn off the power to your computer. 2. For the PC: Connect the 15-pin mini D-SUB of the appropriate signal cable to the connector of the display card in your system (Figure A.1). Tighten all screws. For the Mac: Connect the MultiSync LCD1510TM, MultiSync LCD1510VTM or MultiSync LCD2010TM Macintosh cable adapter to the computer (Figure B.1). Attach the 15-pin mini D-SUB end of the appropriate signal cable to the MultiSync LCD1510, MultiSync LCD1510V or MultiSync LCD2010 Macintosh cable adapter (Figure B.1). Tighten all screws. NOTE: To obtain the MultiSync LCD1510, MultiSync LCD1510V or MultiSync LCD2010 Macintosh cable adapter, call NEC Technologies at (800) 820-1230. 3. For the MultiSync LCD1510 and MultiSync LCD1510V: Connect the 15-pin mini D SUB of the video signal cable and AC Adapter cable to the appropriate connectors on the back of the monitor (Figure C.1). For the MultiSync LCD2010: Remove connector cover on back of monitor (Figure D.1). Connect the BNC cables and AC adapter cable to the appropriate connectors on the back of the monitor. Connect the red BNC cable to the BNC connector on the monitor labeled R, the green BNC cable to the BNC connector labeled G/Sync, the blue BNC cable to the BNC connector labeled B. If you have a fourth BNC connector (Composite Sync), connect it to the BNC connector on the monitor labeled H/CS. If you have a fifth BNC connector (Vertical Sync), connect it to the BNC connector on the monitor labeled VS (Figure D.1). Place the 15-pin VGA to BNC Cable under Clip A (Figure D.1A). Then place the 15-pin VGA to BNC cable under Clip B (Figure D.1B) Replace connector cover. NOTE: Incorrect cable connections may result in irregular operation, damage display quality/components of LCD module and/or shorten the module's life. 4. Connect one end of the power cord to the AC Adapter and the other end to the power outlet (Figure E.1). 5. Turn on the monitor (Figure F.1) and the computer. 6. To complete the setup of your MultiSync LCD monitor: A. For the MultiSync LCD1510/LCD1510V monitors, set the resolution to 1024 x768 @ 75 Hz. For the MultiSync LCD2010 monitor, set the resolution to 1280 x 1024 @ 60 Hz. NOTE: For download information on the Windows ® 95/98 INF file for your MultiSync LCD monitor, refer to the References section of this User's Manual. B. Use the following OSMTM controls: · Auto Adjust Contrast · Auto Adjust · Image Adjust ­ Fine (MultiSync LCD2010 monitor only) NOTE: Manual adjustment of the H/V Position and Image Adjust H. Size/Fine controls may be required to complete setup of your MultiSync monitor. For a full description of these OSM controls, refer to the Controls section of this User's Manual. 7. Refer to User's Manual in the Pivot® Software CD case for installation and operation of this software. NOTE: If you have any problems, please refer to the Troubleshooting section of this User's Manual. 3 To attach your MultiSync® LCD monitor to your system, follow these instructions: 78133314.wpc 5 5/7/99, 4:13 PM Quick Start cont. Mac Adapter (not included) 15-pin mini D-SUB Figure A.1 MultiSync LCD1510 monitor Figure B.1 Connector Cover MultiSync LCD2010 monitor Figure C.1 Power Cord Figure E.1 Figure F.1 Figure D.1A Figure D.1B Figure D.1 Power Switch 4 78133314.wpc 6 5/7/99, 4:13 PM Quick Start cont. Cable Management To use the cable management feature, lift up then remove back cover (Figure CM.1). Place all cables into the vertical groove, leaving 6" of slack in the cables to allow the monitor to rotate between Landscape and Portrait orientation (Figure CM.2). To replace back cover, push in then slide down (Figure CM.3). Cable Cover Lift up then remove back cover Leave sufficient length of cable Push in and slide down Figure CM.1 Figure CM.2 Figure CM.3 Raise and Lower Monitor Screen The monitor may be raised or lowered in either Portrait or Landscape mode. To raise or lower screen, place one hand under bottom of screen (Figure RL.1), lift or lower slightly and simultaneously push the button on the bottom back of the stand (Figure RL.2). Screen will lower while button is pushed in. Release button to lock screen in place. CAUTION: Although the monitor has been designed not to lower automatically when the button is pushed, ALWAYS support the bottom of the screen with one hand. Figure RL.1 5 Figure RL.2 78133314.wpc 7 5/7/99, 4:13 PM Quick Start cont. Screen Rotation Before rotating, the screen must be raised to the highest level to avoid knocking the screen on the desk or pinching your fingers. To raise the screen, place one hand under bottom of screen (Figure RL.1), lift up and simultaneously push the button on the bottom back of the stand. (Figure RL.2). To rotate screen, place hands on each side of the monitor screen and turn clockwise from Landscape to Portrait or counter-clockwise from Portrait to Landscape (Figure R.1). To toggle the orientation of the OSMTM menu between Landscape and Portrait modes, press the RESET button while OSM menu is off. Figure R.1 6 78133314.wpc 8 5/7/99, 4:13 PM Quick Start cont. Tilt and Swivel Grasp both sides of the monitor screen with your hands and adjust the tilt and swivel as desired (Figure TS.1). Remove Monitor Stand for Mounting To prepare the monitor for alternate mounting purposes: 1. Disconnect all cables. 2. Place one hand under bottom of screen (Figure RL.1), lift up and simultaneously push the button on the bottom back of the stand raise it to the maximum height (Figure RL.2). 3. Place monitor face down on a non-abrasive surface. (Place the screen on a 2-inch platform so that the stand is parallel with the surface.) (Figure S.1) 40mm Figure TS.1 Figure S.1 4. Remove cable cover. Remove the 4 screws connecting the monitor to the stand and lift off the stand assembly (Figure S.2). The monitor is now ready for mounting in an alternate manner. 5. Reverse this process to reattach stand. NOTE: Use only VESA-compatible alternative mounting method. 3 2 1 4 Figure S.2 7 78133314.wpc 9 5/7/99, 4:13 PM Controls OSMTM (On-Screen Manager) control buttons on the front of the monitor function as follows: To access OSM press any of the control buttons ( , , , ) or the PROCEED or EXIT button. To rotate OSM between Landscape and Portrait modes, press the RESET button. Main Menu EXIT CONTROL / Exits the OSM controls. Moves the highlighted area up/down to select one of the controls. Moves the highlighted area left/right to select control menus. Has no function Resets the highlighted control menu to the factory setting. Sub-Menu Exits to the OSM main menu. Moves the highlighted area up/down to select one of the controls. Moves the bar left/ right to increase or decrease the adjustment. Activates Auto Adjust and ALL RESET functions. Resets the highlighted control to the factory setting. CONTROL / PROCEED RESET NOTE: When RESET is pressed in the main and sub-menu, a warning window will appear allowing you to cancel the RESET function by pressing the EXIT button. Brightness/Contrast Controls BRIGHTNESS CONTRAST AUTO Adjusts the overall image and background screen brightness. Adjusts the image brightness in relation to the background. AUTO ADJUST CONTRAST Adjusts the image displayed for non-standard video inputs. OSM LOCK OUT The OSM LOCK OUT control completely locks out access to all OSM control functions. When attempting to activate OSM controls while in the LOCK OUT mode, a screen will appear indicating that OSM controls are locked out. · To enter the LOCK OUT mode, simultaneously press the PROCEED and button. The LOCK OUT window will appear. · To activate the LOCK OUT function, simultaneously press and hold down the PROCEED and button. The OSM window will disappear within seconds and the LOCK OUT function will be activated. · To deactivate the LOCK OUT ...