NEC LCD Series MultiSync LCD1510+ User's Manual TM ® You can register your t product online a / www.nectech.com on productregistrati 78134702.wpc 1 10/15/99, 1:59 PM Index Warning .................................................................................. 1 Contents ................................................................................... 2 Quick Start ............................................................................ 3-6 Controls ................................................................................ 7-9 Recommended Use ............................................................. 10-11 Specifications ......................................................................... 12 Features ................................................................................. 13 Troubleshooting ...................................................................... 14 References .............................................................................. 15 Limited Warranty .................................................................... 16 TCO'99 ............................................................................ 17-18 Avertissement ......................................................................... 20 Contenu ................................................................................. 21 Mise en marche rapide ...................................................... 22-25 Commandes ...................................................................... 26-28 Usage recommandé ........................................................... 29-30 Fiche technique ....................................................................... 31 Fonctions ................................................................................ 32 Dépannage ............................................................................ 33 Références .............................................................................. 34 Garantie limitée ...................................................................... 35 TCO'99 ............................................................................ 36-37 Warnung ............................................................................... 40 Lieferumfang .......................................................................... 41 Quick Start ........................................................................ 42-45 Bedienungselemente ........................................................... 46-48 Empfehlungen für die Verwendung ...................................... 49-50 Technische Daten .................................................................... 51 Funktionen ............................................................................. 52 Fehlerbehebung ...................................................................... 53 Verweise ................................................................................ 54 Beschränkte Gewährleistung .................................................... 55 TCO'99 ............................................................................ 56-57 78134702.wpc 2 10/15/99, 1:59 PM WARNING TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT USE THIS UNIT'S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS THE PRONGS CAN BE FULLY INSERTED. REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. CAUTION CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, MAKE SURE POWER CORD IS UNPLUGGED FROM WALL SOCKET. TO FULLY DISENGAGE THE POWER TO THE UNIT, PLEASE DISCONNECT THE POWER CORD FROM THE AC OUTLET.DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol warns user that uninsulated voltage within the unit may have sufficient magnitude to cause electric shock. Therefore, it is dangerous to make any kind of contact with any part inside this unit. This symbol alerts the user that important literature concerning the operation and maintenance of this unit has been included. Therefore, it should be read carefully in order to avoid any problems. DOC: This Class B digital apparatus meets all requirements of the Canadian InterferenceCausing Equipment Regulations. C-UL: Bears the C-UL Mark and is in compliance with Canadian Safety Regulations according to C.S.A. C22.2 No. 950. Canadian Department of Communications Compliance Statement FCC Information 1. Use the attached specified cables with the LA-1571HMW-1 color monitor so as not to interfere with radio and television reception. (1) Please use the supplied power cord or equivalent to ensure FCC compliance. (2) Please use the supplied AC Adapter (#A1240T01). (3) Please use the supplied shielded video signal cable. Use of other cables and adapters may cause interference with radio and television reception. 2. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. · Consult your dealer or an experienced radio/TV technician for help. If necessary, the user should contact the dealer or an experienced radio/television technician for additional suggestions. The user may find the following booklet, prepared by the Federal Communications Commission, helpful: "How to Identify and Resolve Radio-TV Interference Problems." This booklet is available from the U.S. Government Printing Office, Washington, D.C., 20402, Stock No. 004-000-00345-4. 1 78134702.wpc 3 10/15/99, 1:59 PM Contents You can register your product online at www.nectech.com/productregistration Your new NEC Technologies MultiSync® LCD monitor box* should contain the following: · MultiSync LCD1510+TM Monitor with tilt/swivel/pivot stand · Power Cord · AC Adapter (#A1240T01) · Video Signal Cable · User's Manual · NEC LCD Setup Software, Pivot Software and other helpful files MultiSync LCD1510+ monitor with Video Signal Cable and AC Adapter Power Cord NE Set C LCD Piv up So and ot So ftwa re f oth er h twar e elp ful fil es User's Manual CD Software * Remember to save your original box and packing material to transport or ship the monitor. 2 78134702.wpc 4 10/15/99, 1:59 PM Quick Start To attach your MultiSync® LCD monitor to your system, follow these instructions: 1. Turn off the power to your computer. 2. For the PC: Connect the 15-pin mini D-SUB of the appropriate signal cable to the connector of the display card in your system (Figure A.1). Tighten all screws. For the Mac: Connect the MultiSync Macintosh cable adapter to the computer (Figure B.1). Attach the 15-pin mini D-SUB end of the appropriate signal cable to the MultiSync Macintosh cable adapter (Figure B.1). Tighten all screws. NOTE: To obtain the MultiSync Macintosh cable adapter, call NEC Technologies at (800) 820-1230. 3. Connect the 15-pin mini D-SUB of the video signal cable and the AC Adapter cable. Place the AC Adapter cable under Clip A (Figure C.1). NOTE: Incorrect cable connections may result in irregular operation, damage display quality/components of LCD module and/or shorten the module's life. 4. Connect one end of the power cord to the AC Adapter and the other end to the power outlet (Figure D.1). 5. Turn on the monitor (Figure E.1) and the computer. 6. To complete the setup of your MultiSync LCD monitor: A. Set the resolution to 1024 x768 @ 75 Hz. NOTE: For download information on the Windows ® 95/98 INF file for your MultiSync LCD monitor, refer to the References section of this User's Manual. B. Use the following OSMTM controls: · Auto Adjust Contrast · Auto Adjust NOTE: Manual adjustment of the H/V Position and Image Adjust H. Size/Fine controls may be required to complete setup of your MultiSync monitor. For a full description of these OSM controls, refer to the Controls section of this User's Manual. 7. Refer to User's Manual in the LCD Setup Software CD case for installation and operation of this software. NOTE: If you have any problems, please refer to the Troubleshooting section of this User's Manual. 3 78134702.wpc 5 10/15/99, 1:59 PM Quick Start cont. 15-pin mini D-SUB MAC Adapter (not included) 15-pin mini D-SUB Figure A.1 Figure B.1 Clip A Power Button Figure C.1 Figure E.1 Figure D.1 Power Cord 4 78134702.wpc 6 10/15/99, 1:59 PM Controls Quick Start cont. Raise and Lower Monitor Screen The monitor may be raised or lowered in either Portrait or Landscape mode. To raise or lower screen, place hands on each side of the monitor and lift or lower to the desired height (Figure RL.1). Figure RL.1 Screen Rotation Before rotating, the screen must be raised to the highest level to avoid knocking the screen on the desk or pinching your fingers. To raise the screen, place hands on each side of the monitor and lift up to the highest position (Figure RL.1). To rotate screen, place hands on each side of the monitor screen and turn clockwise from Landscape to Portrait or counter-clockwise from Portrait to Landscape (Figure R.1). To toggle the orientation of the OSMTM menu between Landscape and Portrait modes, press the RESET button while OSM menu is off. Figure R.1 5 78134702.wpc 7 10/15/99, 1:59 PM Quick Start cont. Tilt and Swivel Grasp both sides of the monitor screen with your hands and adjust the tilt and swivel as desired (Figure TS.1). Remove Monitor Stand for Mounting To prepare the monitor for alternate mounting purposes: 1. Disconnect all cables. Figure TS.1 2. Place hands on each side of the monitor and lift up to the highest position (Figure RL.1). 3. Place monitor face down on a non-abrasive surface. (Place the screen on a 2-inch platform so that the stand is parallel with the surface.) (Figure S.1) 2-in Figure S.1 4. Remove the stand cover by sliding the top/bottom pieces off the stand (Figure S.2). Remove the 4 screws connecting the monitor to the stand and lift off the stand assembly (Figure S.3). The monitor is now ready for mounting in an alternate manner. 5. Reverse this process to reattach stand. NOTE: Use only VESA-compatible alternative mounting method. 4 1 3 2 Figure S.2 and Figure S.3 6 78134702.wpc 8 10/15/99, 1:59 PM Controls OSMTM (On-Screen Manager) control buttons on the front of the monitor function as follows: To access OSM press any of the control buttons ( , , , ) or the PROCEED or EXIT button. To rotate OSM between Landscape and Portrait modes, press the RESET button. Main Menu EXIT CONTROL / Exits the OSM controls. Moves the highlighted area up/down to select one of the controls. Moves the highlighted area left/right to select control menus. Has no function Resets the highlighted control menu to the factory setting. Sub-Menu Exits to the OSM main menu. Moves the highlighted area up/down to select one of the controls. Moves the bar left/ right to increase or decrease the adjustment. Activates Auto Adjust and ALL RESET functions. Resets the highlighted control to the factory setting. CONTROL / PROCEED RESET NOTE: When RESET is pressed in the main and sub-menu, a warning window will appear allowing you to cancel the RESET function by pressing the EXIT button. Brightness/Contrast Controls BRIGHTNESS CONTRAST AUTO Adjusts the overall image and background screen brightness. Adjusts the image brightness in relation to the background. AUTO ADJUST CONTRAST Adjusts the image displayed for non-standard video inputs. OSM LOCK OUT The OSM LOCK OUT control completely locks out access to all OSM control functions. When attempting to activate OSM controls while in the LOCK OUT mode, a screen will appear indicating that OSM controls are locked out. · To enter the LOCK OUT mode, simultaneously press the PROCEED and button. The LOCK OUT window will appear. · To activate the LOCK OUT function, simultaneously press and hold down the PROCEED and button. The OSM window will disappear within seconds and the LOCK OUT function will be activated. · To deactivate the LOCK OUT mode, simultaneously press the PROCEED and button. 7 78134 ...