User manual NEC N401I

Emergency Services and Emergency Services and Safety Safety Precautions Precautions Emergency Services To make an emergency call in any country · Do not put your phone's battery in your mouth as battery Press 1 1 2 . Ask the operator for the service which you require: Police, Ambulance, Fire Brigade, Coastguard or Mountain Rescue Services. Give your position and, if possible, remain stationary to maintain phone contact. The 112 emergency number service is available on every digital network service. The number 999 is an alternative emergency number for the UK only, and can only be used with a valid SIM card. General Care A cellphone contains delicate electronic circuitry, magnets, and battery systems. You should treat it with care and give particular attention to the following points. · Do not allow the phone or its accessories to come into contact with liquid or moisture at any time. · Do not place anything in the folded phone. · Do not expose your phone to extreme high or low temperatures. · Do not expose your phone to naked flame, cigars or cigarettes. · Do not paint your phone. · Do not drop or subject your phone to rough treatment. · Do not place the phone alongside computer disks, credit cards, travel cards and other magnetic media. The information contained on disks or cards may be affected by the phone. · Do not leave the phone or the battery in places where the temperature could exceed 60°C; e.g. on a car dashboard or on a window sill, behind glass in direct sunlight, etc. · Do not remove the phone's battery while the phone is switched on. · Take care not to allow metal objects, such as coins or key rings, to contact or short-circuit the battery terminals. · Do not dispose of battery packs in a fire. Your phone's Liion batteries may be safely disposed of at Li-ion recycling points. For more specific battery and power supply information, see page 3. Due to the nature of the cellular system, the success of emergency calls cannot be guaranteed. electrolytes may be toxic if swallowed. · Do not attempt to dismantle the phone or any of its accessories. · This equipment is fitted with an internal battery that can only be replaced by a qualified service engineer. There is a risk of explosion if the battery is replaced by an incorrect type. Dispose of the used battery in accordance with the manufacturer's instructions. · Using any battery pack, AC adapter or Vehicle power adapter (option) not specified by the manufacturer for use with this phone creates a potential safety hazard. · The earpiece may become warm during normal use and the unit itself may become warm during charging. · Use a damp or anti-static cloth to clean the phone. Do NOT use a dry cloth or electrostatically charged cloth. Do not use chemical or abrasive cleaners as these could damage the case. · Remember to recycle: the cardboard packaging supplied with this phone is ideal for recycling. · Do not leave the battery pack empty or disconnected for a long time, otherwise some data may be initialized. · Your phone contains metal which may cause you an itch, a rash or eczema depending on your constitution or physical condition. · Take care not to put your phone in the back pocket of your trousers or skirt and then sit on it. Also, do not put your phone at the bottom of bag where it may subject to excessive weight or pressure. Doing so may damage the LCD and camera lens and cause them malfunction. · Take care not to hold the Light too close to your or other people's eyes when the Light is lit. · Do not aim or direct the InfraRed (IR) data port towards your or other people's eyes when using the IR data exchange. · The foam covers the earpiece of the headset (option). Do not put any other part of the headset in your ears. Aircraft Safety · Switch off your phone and remove its battery when inside or near aircraft. The use of cellphones in aircraft is illegal. It may be dangerous to the operation of the aircraft and it may disrupt the cellular network. Failure to observe this instruction may lead to suspension or denial of cellphone service to the offender, or legal action, or both. · Do not use your phone on the ground without the permission of the ground crew. Hospital Safety · Switch off your phone in areas where the use of cellphones is prohibited. Follow the instructions given by the respective medical facility regarding the use of cellphones on their premises. General Safety · Observe `Turn off 2-way radio' signs, such as those near stores of fuel, chemicals or explosives. · Do not allow children to play with the phone, charger or batteries. · Small parts are included in your phone. Keep them out of reach of small children, for whom it could be a choking hazard. · The operation of some medical electronic devices, such as hearing aids and pacemakers, may be affected if a cellphone is used next to them. Observe any warning signs and manufacturer's recommendations. · If you have a weak heart, you should take extra precautions when setting functions such as the Vibrator and Ringer volume functions for incoming calls. · If you set the Vibrator setting to anything other than OFF, be careful that the phone is not near a source of heat (e.g. a heater) and that it does not fall from a desk due to the vibration. Road Safety · You MUST exercise proper control of your vehicle at all times. Give full attention to driving. · Observe all the recommendations contained in your local traffic safety documentation. · Pull off the road and park before making or answering a call if driving conditions so require. · You MUST NOT stop on the hard shoulder of a motorway to answer or make a call, except in an emergency. · Switch off your phone at a refuelling point, such as a petrol station, even if you are not refuelling your own car. · Do not store or carry flammable or explosive materials in the same compartment where a radio transmitter, such as a cellphone, is placed. · Electronic vehicle systems, such as anti-lock brakes, speed control and fuel injection systems are not normally affected by radio transmissions. The manufacturer of such equipment can advise if it is adequately shielded from radio transmissions. If you suspect vehicle problems caused by radio transmissions, consult your dealer and do not switch on your phone until it has been checked by qualified approved installers. Vehicles Equipped with an Air Bag An air bag inflates with great force. Do not place objects, including either installed or portable wireless equipment, in the area over the air bag or in the air bag deployment area. If in-vehicle wireless equipment is improperly installed and the air bag inflates, serious injury could result. i Third Party Equipment The use of third party equipment, cables or accessories, not made or authorized by NEC, may invalidate the warranty of your cellphone and also adversely affect the phone's operation. For example use only the NEC mains cable supplied with the AC charger. Service The cellphone, batteries and charger contain no userserviceable parts. We recommend that your NEC cellphone is serviced or repaired by an NEC authorized service centre. Please contact your Service Provider or NEC for advice. Non-Ionizing Radiations The radio equipment shall be connected to the antenna via a non-radiating cable (e.g. coax). The antenna shall be mounted in a position such that no part of the human body will normally rest close to any part of the antenna unless there is an intervening metallic screen, for example, the metallic roof. Use only an antenna that has been specifically designed for your phone. Use of unauthorized antennas, modifications or attachments could damage your phone and may violate the appropriate regulations, causing loss of performance and radio frequency (RF) energy above the recommended limits. Efficient Use For optimum performance with minimum power consumption, note the following: · Your phone has the internal antenna. Do not cover part of the internal antenna of the phone with your hands. This affects call quality, may cause the phone to operate at a higher power level than needed and may shorten talk and standby times. Radio Frequency Energy Your phone is a low-power radio transmitter and receiver. When it is turned on, it intermittently receives and transmits radio frequency (RF) energy (radio waves). The system that handles the call controls the power level at which the phone transmits. Exposure to Radio Frequency Energy Your phone is designed not to exceed the limits for exposure to RF energy set by national authorities and international health agencies. * These limits are part of comprehensive guidelines and establish permitted levels of radio wave exposure for the general population. The guidelines were developed by independent scientific organizations such as ICNIRP (International Commission on Non-Ionizing Radiation Protection) through periodic and thorough evaluation of scientific studies. The limits include a substantial safety margin designed to assure the safety of all persons, regardless of age and health, and to account for any variations in measurements. *Examples of radio frequency exposure guidelines and standards that your phone is designed to conform to: · ICNIRP, "Guidelines for limiting exposure to time-varying electric, magnetic, and electromagnetic fields (up to 300 G Hz)-International Commission on Non-Ionizing Radiation Protection (ICNIRP)". Health Physics, vol. 74. pp, 494-522, April 1998. · 99/519/EC Council Recommendation on the limitation of exposure to the general public toelectromagnetic fields 0 Hz-300 GHz, Official Journal of the European Communities, July 12,1999. · ANSI/IEEE C95.1-1992. "Safety levels with respect to human exposure to radio frequencyelectromagnetic fields, 3kHz to 300 GHz". The Institute of Electrical and Electronics Engineers Inc., New York, 1991. · FCC Report and Order, ET Docket 93-62, FCC 96-326, Federal Communications Commission (FCC), August 1996. · Radio communications (Electromagnetic Radiation Human Exposure) Standard 1999, Australian Communications Authority (ACA), May 1999. Declaration of Conformity · This product complies with the requirements of the R&TTE Directive 1999/5/EC. The `Declaration of Conformity' leaflet can be found within this box. License · T9® Text Input and the T9 logo are registered trademarks of Tegic Communication. "T9 Text Input is licensed under one or more of the following: U.S. Pat. Nos. 5,818,437, 5,953,541, 5,187,480, 5,945,928, 6,011,554, and 6,307,548; Australian Pat. No. 727539; Canadian Pat. No. 1,331,057; United Kingdom Pat. No. 2238414B; Hong Kong Standard Pat. No. HK0940329; Republic of Singapore Pat. No. 51383; Euro. Pat. No. 0 842 463 (96927260.8) DE/DK, FI, FR, IT, NL, PT. ES, SE, GB; Republic of Korea Pat. Nos. KR201211B1 and KR226206B1; and additional patents are pending worldwide" · USE OF THIS PRODUCT IN ANY MANNER THAT COMPLIES WITH THE MPEG-4 VISUAL STANDARD IS PROHIBITED, EXCEPT FOR USE DIRECTLY RELATED TO (A) DATA OR INFORMATION ENCODED BY A CONSUMER FOR PERSONAL AND NONCOMMERCIAL USE WITHOUT REMUNERATION; (B) DATA OR INFORMATION (i) GENERATED BY AND OBTAINED WITHOUT CHARGE FROM A CONSUMER NOT THEREBY ENGAGED IN A BUSINESS ENTERPRISE, AND (ii) FOR PERSONAL USE ONLY; · Helvetica is a registered Trademark of Heidelberger AND (C) OTHER USES SPECIFICALLY AND SEPARATELY LICENSED BY MPEG LA, L.L.C. Druckmaschinen AG which may be registered in certain jurisdictions. · ©2002 Music Airport Inc., http://www.music-airport.com/ · Java and all Java-based trademarks and logos are trademarks or registered trademarks of Sun Microsystems, Inc in the U.S. and other countries. · This product contains ACCESS Co., LTD's Compact NetFrontTM Plus internet browser software. Copyright © 1998-2004 ACCESS CO., LTD. Compact NetFrontTM is a registered trademark or trademark of ACCESS CO., LTD in Japan and selected countries worldwide. · This product contains ACCESS CO., LTD's JV-Lite2TM Java virtual machine software. Copyright © 2000-2004 ACCESS CO., LTD. JV-Lite2TM is a registered trade mark or trademark of ACCESS COl, LTD, in Japan and selected countries world wide. · This product contains ACCESS CO., LTD's IrFront® Infrared communication software. Copyright ©1996-2004 ACCESS CO.,LTD. · i-mode and i-mode logos are trademarks or registered trademarks of NTT DoCoMo. For the purpose of improvement, the specifications for this product and its accessories are subject to complete or partial change without prior notice. ii Before You Start User's manual conventions The instructions in this user's manual make use of the shortcuts selection except special cases. The following markers are used throughout the user's manual to attract your attention: This type of paragraph will contain details of where to find information related to the topic in question. This type of paragraph will contain information worth noting. This type of paragraph will contain important information. This type of description will contain procedures to operate your phone. Menu shortcuts selection The alternative shortcuts method of selection lets you jump straight to a menu or function without highlighting an icon and scrolling through the intermediate menu options. The selection are made by pressing numbers on the keypad which relate to the displayed menu options. The instructions in this user's manual make use of the shortcuts selection, except in special cases. Reading the titles Some titles in this manual contain information on how to access the functions. In these titles, M stands for , the numbers indicate the menu shortcut numbers (see "Overview of menu function" on page ix for details) and ... (three periods) indicate that there are more operations described in the paragraph. Reading the procedures "Highlight" means to use the four way navigation keys ( ) to move the area emphasized with different colouring. "Select" means to highlight an item and then press . Procedures are written omitting the verb "press", except in some special cases. For example, 1 2 means to: Start from the standby screen Press to display the Main menu screen Press 1 to display the Settings screen Press 2 to display the Phone modes screen Simple procedures are connected by arrows (). Check box/Radio button A check box enables/disables an option out of a set of options, and multiple check boxes can be selected at the same time. On the other hand, selecting a radio button automatically cancels the previous selection, so only one radio button can be selected at one time. A check box/radio button option can be selected/cancelled by highlighting it and pressing . iii Display information Desktop icon area Status bar area Menu title This area contains icons which indicate the battery strength, new SMS/MMS message(s), signal strength, etc. (see page vii). On screens other than the standby screen, the clock display is placed in this area. This area contains the automatically displayed and the manually created desktop icons. They provide shortcuts to certain items/functions. Shortcut menu number The current menu number is displayed. Page scroll bar Displayed when you can press to scroll to the next page. Help area This area contains help information appropriate for the current screen (e.g. key presses remaining when composing a message). Shortcut number Press the appropriate number to jump straight to a next menu. The row colour is changed when selected (e.g. to activate/deactivate a facility). The Liquid Crystal Displays (LCD) on your phone are manufactured using high-precision technology. Even so, the LCD may contain pixels (dots) that fail to light or that remain permanently lit. Note that this is normal and does not indicate a problem with your display. iv Softkey area Help icons This area contains context sensitive descriptions of the Softkeys' functions appropriate for the current screen. Displayed when you can use the key represented by these icons (see page vii). Displayed when you can press or the shortcut number to show the next menu. Next menu icon Parts and functions Earpiece Speaker Main-LCD 2nd-LCD LED & light Camera Through-hole for straps Side up key Side down key 4 way navigation key ( ) Softkey1(SK1) Menu ( ) key Send ( ) key Internal antenna Select key ( ) Softkey2(SK2) Phonebook ( )key Clear (CLR)/Back key Earphone jack cover End/on-off ( ) key IR port Rear cover for battery Alphanumeric keys Mouthpiece Charger connector cover v Keypad shortcuts The following operations are available from the standby screen. Key Operation that involves pressing a key Accessing the Main menu screen SK1 SK2 Accessing the Mail screen Accessing the i-mode menu screen Accessing the Phonebook list screen Accessing the Phone modes screen Accessing the My data screen Accessing the received calls list Accessing the missed calls list Accessing the dialled calls list Highlighting a desktop icon Ending a call or returning to the standby screen CLR 1 2 to 9 0 # Deleting character or returning to the previous screen Entering phone numbers Entering phone numbers Entering phone numbers Entering # Entering Side up Accessing the volume control screen when your phone is open (Use , Side keys or 0 to 9 keys to adjust the volume.) Activating the ring silencer function when you receive a call Accessing the volume control screen when your phone is open Side down (Use , Side keys or 0 to 9 keys to adjust the volume.) Activating the ring silencer function when you receive a call See page ix 42 38 47 22 61 10 10 10 19 ­ ­ 5 5 5 6 6 21 21 21 21 Turning on the light (To turn it off, press any key or open/close your phone.) ­ Operation that involves pressing and holding a key Setting/Cancelling the Side key lock Accessing the Inbox screen Accessing the JavaTM applications screen Accessing the Message screen Setting the phone to Meeting mode/Returning to the previous mode Accessing the voice recall Accessing the received calls list Accessing the missed calls list Accessing the dialled calls list Accessing the homepage (when Set homepage is set) Powering off Deletes all the automatically displayed desktop icons Deleting all characters when you enter text Calling the Voice mail centre One-touch dial to the corresponding number in the phonebook (SIM) Entering + when you make an international call Entering a pause Switching the ALS line 1/2 (if the SIM card supports ALS) Accessing the camera view finder screen See page 21 42 66 27 22 7 10 10 10 41 4 19 ­ 55 7 13 ­ 21 56 vi LCD and displayed icons Main-LCD 1 2 3456 78 9 10 Indicates that there is a new mail/MMS in your phone. This orange icon blinks while a mail/MMS is being downloaded Indicates that the memory for mail/MMS is full. 10 Network name (indicated in orange when using roaming service) Appears when you are outside the service area. 11 Desktop icons See "Desktop icons" on page 19 for details. 4 6 (red, green/red, green) Indicates that new voice mail messages are on the network (No ALS/ALS Line 1/2). 12 Indicates the call diversion is set. Indicates the Meeting mode, Pocket mode, Car mode. 11 15 16 17 12 13 14 Indicates secured communication on SSL. 7 Indicates that GPRS is active for purposes other than i-mode connections. (gray) Indicates that the phone is in the GSM (Global System for Mobile communication) network service area and GPRS is active. (yellow) Indicates that the GPRS is available and i-mode is active. Indicates that the i-mode connection is carried out. No icon appears for the Normal mode. Indicates alarm-on, sound-off, vibrator-on, soundoff/vibrator-on. Indicates the IR modem is set to on, the auto start of a JavaTM application has failed. Date 1 Indicates the battery level. (red, green, blue) Indicates the battery charging status (fast, slow, pause). 2 Indicates that there is a new SMS in your phone. Indicates that there is a new SMS on the network. 13 14 Day of week 15 Remote time 16 Local time 17 Indicates that the i-mode lock is on. Indicates that the SIM memory is full. Indicates that the Inbox in your phone is full. (green) Indicates that there is a mail on the server. (blue) Indicates that there is an MMS on the server. (pink) Indicates that there are mail and MMS on the server. (orange) 3 No icon appears when the phone is outside the GSM network service area, or when the phone is in the GSM network service area and GPRS is not attached. Indicates that you can use the options menu by pressing Indicates that you can use the phonebook list by pressing . Indicates the usable keys in black, while a JavaTM application is in operation. Indicates that the help display is available when using SIM toolkit 8 Indicates the line status (ALS line 1/2 no ALS).The icon with displayed in red indicates that the ALS line 1 or 2 is unencrypted/no ALS. 9 Indicates the signal strength level. vii Indicates that a JavaTM application is in operation. Indicates the video is played in normal/enlarged screen size. 5 Indicates that the alarm is set. 8 Displays the current volume level. The 0 is mute and 9 is the maximum. 2 Indicates single/burst mode (camera). Indicates the video mode is on or the video is recording. Indicates that the self timer is on. 6 Indicates that the vibrator is set. 2nd-LCD 1 2 3 45 6 7 8 7 Indicates that the phone is in the Meeting mode, Pocket mode, Car mode. No icon appears for the Normal mode. Indicates the signal strength level. 3 4 8 1 Indicates the quality of the picture (super fine, fine, normal, economy or super economy). Indicates the quality of the video. Indicates the battery level. (red, green, blue) Indicates the battery charging status (fast, slow, pause). Indicates that there is a new SMS in your phone. Indicates that there is a new SMS on the network. Appears when you are outside the service area. 5 Indicates the photo/video screen size. 2 6 Indicates the shooting environment. 9 11 10 12 7 8 Indicates the brightness setting. The "+2" setting is the brightest. Indicates the zoom level. Indicates that the SIM memory is full. Indicates that the Inbox in your phone is full. (green) Indicates that there is a mail on the server. (blue) Indicates that there is an MMS on the server. (pink) Indicates that there are mail and MMS on the server. (orange) Indicates that there is a new mail/MMS in your phone. Indicates that the memory for a mail/MMS is full. (red, green/red, green) Indicates that a new voice mail message is on the network (No ALS/ALS Line 1/2). The left image is when the phone is folded, and the right image is when the phone is open. 3 9 Indicates single or burst mode of the camera. (blue) Indicates that the video mode. (red) Indicates the video is recording. 2 Indicates the video mode is on, the video is playing, on pause, fast forwarding, or rewinding. 4 Indicates the track information of the video (the video file only, the video and audio file, or the audio file only). 10 Indicates that the self timer is on. 11 Indicates the photo/video screen size. 7 viii 4 12 Indicates the battery level. Overview of menu function Standby screen Main menu screen CLR or Key 1 Main menu Settings Second level menu Phone Phone modes Main-LCD 2nd-LCD Power saving Calls Security Network Reset settings Inbox Drafts Outbox Sent Folder1 Folder2 CB Key 3 4 5 6 2 Message The Main menu has a set of icons for its top levels of options (examples of the top level are shown right) ) and (menu which can be selected either using a combination of the 4-way navigation key ( selection), or just the keypad (shortcuts selection). The title of the selected option will be displayed in the Help area. SIM toolkit icon is displayed only when your SIM card supports this function. With the Main menu screen displayed, press 0 to display your own number. Main menu i-mode Phonebook Second level menu i-mode Settings Lists Information # Call options Camera Video recorder Videos Sounds Pictures Music Key 7 8 Main menu Java Accessory Second level menu Programs Prog backlight Music player Calculator Clock alarm Scheduler ToDo list Notepad Voice memo Currency Infrared Camera My data 9 SIM toolkit ix Getting Started Basic Calls & Phone Use Text Entry IR Data Exchange Desktop icons Settings (M1) Message (M2) i-mode (M3) Phonebook (M4) Camera (M5) My data (M6) JavaTM (M7) Accessory (M8) Index 1 5 14 17 19 21 27 33 47 56 61 66 68 77 Before You Start iii User's manual conventions............................................. iii Display information ......................................................... iv Parts and functions .......................................................... v LCD and displayed icons ............................................... vii Overview of menu function ............................................. ix Getting Started 1 Multi-party calls ................................................................ 8 Recording a call ............................................................... 9 Call options (M43)............................................................ 9 Call settings (M16) ......................................................... 11 International dialling codes ............................................ 13 Roaming......................................................................... 13 Text Entry 14 Preparing the phone ........................................................1 Standby and talk times.....................................................3 Checking the battery ........................................................3 Low battery alarm ............................................................3 Other battery alarms ........................................................3 Attaching and Removing the Emblem..............................4 Start-up ............................................................................4 Basic Calls & Phone Use 5 Mode change ................................................................. 14 T9® English text input .................................................... 14 Normal text input............................................................ 15 Numeric input................................................................. 16 Key allocations............................................................... 16 IR Data Exchange 17 Making basic calls............................................................5 Ending a call ....................................................................5 Receiving an incoming call ..............................................5 Unsuccessful calls ...........................................................6 Emergency calls...............................................................6 Last number redial ...........................................................6 One-touch dial..................................................................7 Fast dialling......................................................................7 Displaying your own phone number (M0/M416) ..............7 Voice recall ......................................................................7 Options menu (during a call)............................................7 Putting a call on hold........................................................8 Mute .................................................................................8 Transferring a call ............................................................8 Positioning of the phones............................................... 17 IR send........................................................................... 17 IR receive (M891) .......................................................... 18 IR modem (M892) .......................................................... 18 Desktop icons Settings (M1) 19 21 Phone(M11) ................................................................... 21 Phone modes (M12) ...................................................... 22 Main-LCD (M13) ............................................................ 23 2nd-LCD (M14) .............................................................. 23 Power saving (M15) ....................................................... 24 Calls (M16)..................................................................... 24 Security (M17)................................................................ 24 Network (M18) ............................................................... 26 xi Reset settings (M19)...................................................... 26 Message (M2) 27 Message overview ......................................................... 27 Reading a message (M21) ............................................ 28 Creating a message....................................................... 31 Cell broadcast (M27) ..................................................... 33 i-mode (M3) 33 Sounds (M62) ................................................................ 62 Pictures (M63) ............................................................... 62 Music (M64) ................................................................... 63 File selector Options menu ............................................ 64 JavaTM (M7) 66 Programs (M71)............................................................. 66 Prog backlight (M72)...................................................... 67 Accessory (M8) 68 i-mode operation guide .................................................. 33 i-mode screen ................................................................ 38 i-mode menu screen ...................................................... 38 iMenu screen ................................................................. 41 Mail screen .................................................................... 42 i-mode glossary ............................................................. 46 Phonebook (M4) 47 Phonebook types ........................................................... 47 Accessing your phonebook (M4) ................................... 48 Phonebook list Options menu........................................ 49 Personal data Options menu ......................................... 54 Scratchpad number ....................................................... 54 Voice mail (M417).......................................................... 55 Camera (M5) 56 Music player (M81) ........................................................ 68 Calculator (M82) ............................................................ 69 Clock alarm (M83) ......................................................... 69 Scheduler (M84) ............................................................ 70 ToDo list (M85) .............................................................. 72 Notepad (M86)............................................................... 73 Voice memo (M87) ........................................................ 75 Currency (M88).............................................................. 75 Infrared (M89) ................................................................ 76 Index 77 Notes on using the camera............................................ 56 Taking a picture (M51) ................................................... 57 Recording a video (M52) ............................................... 59 My data (M6) 61 Videos (M61) ................................................................. 61 xii Getting Started Preparing the phone Before trying to use your phone, make sure that a valid Subscriber Identity Module (SIM) card is inserted and the battery is charged. SIM card Before using your phone, you must sign-up with one of the digital network service providers. In addition to your subscription details you will receive a personal SIM (Subscriber Identity Module) card which is inserted into your phone. If the SIM card is removed, the phone becomes unusable until a valid SIM card is fitted. It is possible to transfer your SIM card to another compatible phone and resume your network subscription. The screen on your phone will display appropriate messages if no SIM card is fitted. If the phone, or the SIM card, is lost or stolen then you should contact your service provider immediately in order to bar it from use. The phone supports a number of languages and the keyboard symbols have been chosen for world-wide operation. The digital technology of your phone helps to ensure that your conversations are kept secure. The SIM card contains personal data such as your electronic phonebook, messages (see "Message (M2)" on page 27) and also details of the network services you have subscribed to. The phone will not work (except for emergency calls on some networks) unless a valid SIM card is fitted. Be sure to turn the phone off before inserting and removing a SIM card. Otherwise damage to the SIM card can occur. Inserting a SIM card Be sure to turn the phone off before removing the battery pack. of the rear cover as indicated by arrows , slide the rear cover about 3 mm in the direction of arrows with your finger tips. Then, lift the cover up in the direction of arrow to remove it. Lift the finger tab of the battery pack up in the direction of arrow . Then lift the battery pack out in the direction of arrow . With the metal part facing down, insert the straight end of the SIM card under the holder in the direction of arrow . Slide the SIM card all the way until it reaches the end. Align the marks on the battery pack with the marks on the phone. Insert it into the cavity in the phone body in the direction of arrow , making sure that the tabs on the battery pack fit properly into the notches in the phone. Then, press the battery pack down in the direction of arrow to clip it into the phone. Make sure that the battery pack is securely attached to the phone and align the rear cover with the grooves on the phone so that there is a gap of about 3 mm at the end of the cover. After making sure that there is no gap between the rear cover and the phone body, slide the rear cover in the direction of arrows until you hear a click. While pressing down the areas marked with 1 Finger tab Battery Notches Tabs Rear cover Holder About 3 mm About 3 mm SIM card . Check that there is no gap between the rear cover and the phone body. If the SIM card is not fully inserted when the battery is replaced, damage to the SIM card can occur. If the SIM card is already fitted, see "Start-up" on page 4. Removing a SIM card With the battery removed, push the short and straight end of the SIM card with your thumb to slide it gently in the direction of arrow Lift the SIM card after it is completely removed from the holder. Charger connector Charger connector Charging the battery Before trying to use your phone, insert the phone's battery, connect the NEC battery charger (AC cover adapter) supplied with your phone to a suitable mains power socket. Pull open the charger connector cover gently. Be careful when handling the charger connector cover. Do not pull strongly. Charger plug Connect the charger plug (AC adapter) into the charger connector at the bottom of the phone. If your phone is turned on and charging starts, the battery charging icon will be displayed. LED will turn on in red while charging. When charging is complete, the LED will turn off. You are recommended to switch off the phone while charging. If you need to receive calls, your phone can be switched on and left in standby while being charged, although the total time taken to charge is then increased. The colour on the display shows the charging status of battery. (red) Fast battery charging (green) Slow battery charging while the phone is in use (blue) Battery charging is stopped due to overheat Using any battery pack, AC adapter, vehicle power adapter (option) not specified by NEC for use with this phone can be dangerous and may invalidate any warranty and approval given to the cellphone. Do not leave the charger connected to the mains supply when it is not in use. Do not try to charge the battery if the ambient temperature is below 5°C (41°F) or above 35°C (95°F). 2 DO NOT connect a charger or any other external DC source until the phone's battery is inserted. If the phone does not respond, please wait for a few minutes. The charging will then start. If you use the phone while charging, handle the phone carefully since the cable or adapter is connected. If you make/receive a call while charging, the charging may temporarily be interrupted. Charging takes approximately 3 hours with your phone turned off. Even if the phone remains connected to the charger, battery residual capacity may decrease when the phone is used for video recording, playing or other battery consuming operation. IMPORTANT BATTERY CHARGING INFORMATION Charging a very low battery The battery's charge continues to drop after the low battery warning is displayed. In extreme cases where the battery is left uncharged for some considerable time after this warning, a trickle charge is used to slowly top-up the battery to the safe level at which the fast charging can begin. The phone can be in trickle charge for a few minutes before the fast charging starts. Standby and talk times Your phone works closely with the network you are using to provide the services you need, and the standby and talk times achieved will depend on how you use the phone and choices made by the network operator. In particular, factors such as your location within the network, the frequency at which this location is updated, the type of SIM card you have, your reception of area messages or cell broadcast messages and the use of full rate or enhanced full rate speech, will affect both standby and talk times. Checking the battery Check icon at the top of the standby screen. The block on the display shows the charge of your battery pack. Full battery power Partial battery power Low battery power Battery empty Low battery alarm When the battery voltage falls below the working level, a low battery warning is displayed on the screen accompanied by LED illumination and a short tone along with an empty battery icon. The phone will automatically power down shortly afterwards. Please charge the battery as much as possible when the battery is very low. Other battery alarms Your phone may display warnings when the battery temperature is too high, or the voltage of the battery or the charger is over the appropriate level. Follow the instruction given by these warnings immediately. 3 Attaching and Removing the Emblem Attaching the emblem Depressions Removing the emblem Depressions Depressions Depressions Attach the emblem, aligning the holes to fit the 2nd-LCD, LED and camera. Make sure the emblem is fitted over the square depressions on each side of the phone. Remove the emblem by hooking your finger tips near the square depressions and lifting in the direction of the arrows. You can also remove the emblem from the other side of the phone. Start-up Switching the phone on Hold down for about a second to switch on. The screen will display the selected greeting (see page 23) and the phone is then in standby. You may need to charge the battery before using your phone. When your phone is turned on, the specified ringer may sound. If your phone is accidentally turned off while downloading or deleting JavaTM application, it will take longer than usual to start up the phone the next time you turn on the power. Switching the phone off Hold down until the display shows the switch off message. PIN code The SIM card issued by your service provider has a security feature called PIN code protection. The Personal Identification Number (PIN) is a number put on to the card by your service provider, and is 4 to 8 digits long. Some service providers supply SIM cards which will cause your phone to prompt for 4 a PIN code when it is turned on. If this is the case, enter your code with the phone's keypad. If you insert a SIM card other than your own, information such as call logs may be lost. (See "Security (M17)" on page 24 for details.) Basic Calls & Phone Use Making basic calls You make a simple call in the same way as you would with a normal phone, except that you need to press after entering the area Subscriber Trunk Dialling (STD) code and the phone number. To make international calls, you must first enter the international dialling code (see page 13). Use the full STD area code even if you are calling to a person in the same town. If the numbers are too long to be displayed within one line, after pressing , excess part is deleted and `...' is added at its end. The main-LCD display shows the strength of the radio signal that links your phone to the network. The maximum signal strength is shown by 4 shaded blocks and the minimum signal strength by 1 block. Starting a call Key in the phone number. Check the number on the display or SK1 to send the input number to start the call Before the other party answers the call, you can end the call by pressing briefly, pressing SK2 or closing your phone. When you use the headset, you can also end the call by pressing and holding the button on it. When the call is sent, the screen displays the number called or the name stored in the phonebook and a connection graphic or a Calling Line Identification (CLI) picture that has been allocated to the number called (see page 53). and to move the cursor and then press CLR to clear individual digits, or hold down CLR to completely clear a phone number. Correcting mistakes Use the Ending a call While talking, press briefly or close your phone. The phone returns to the standby screen. If is held down, your phone will turn off. When you use the headset, you can also end a call by pressing and holding the button on it. You cannot end a call by closing your phone when the headset is connected. Receiving an incoming call When someone calls your number, the ringer will play (if set - see page 22), the LED glows in the specified colour, and the phone number of the caller may be displayed if the calling line identification facility is available and the caller has activated the feature. If the caller's phone number has been related 5 and stored in your phonebook with a name and a CLI picture (see page 53), that name and picture will be displayed. If the caller has withheld their identity, the screen will give a message that the caller's number is being withheld. You also have options for holding and forwarding calls. These options depend on your network and your subscription arrangements. Accepting an incoming call While receiving an incoming call, press Rejecting an incoming call While receiving an incoming call, press or SK1. When you use the headset, you can also accept an incoming call by pressing the button on it. or SK2 briefly or close your phone. When you use the headset, you can also reject an incoming call by pressing and holding the button on it. You cannot reject a call by closing your phone when the headset is connected. If your phone receives a call and you do not answer it, the screen will display the phone number (or the name if stored) of the caller (if available). This information is stored in the missed calls list. Up to 20 missed calls are stored in this list. You can set your phone to answer a call when any key is pressed (see "Any key answer" on page 21). If you are making a call, the phone gives priority to receiving a call unless you have already pressed See also: "Call diversion (M161)" on page 11 and "Call waiting and holding (M162)" on page 12. See also: "Call options (M43)" on page 9. . Unsuccessful calls If dialled call is not successfully connected, the display will give an appropriate message. If your phone has the auto redial function activated, the number will be automatically called again after a short delay (see page 12). Emergency calls The standard emergency number of 112 can be used. Key in 1 1 2 or SK1 to connect the call to the local emergency services. On some networks, emergency calls can be made using the 112 number without a SIM card inserted. Last number redial You can redial the last number you called. Ensure that the standby screen is displayed and no phone number is shown 6 twice to dial the last number you called. See also: "Call options (M43)" on page 9. One-touch dial One-touch dial for the phonebook (SIM) is available by pressing and holding the number keys between 2 and 9. A number for the One-touch dial corresponds to the location number in the phonebook (SIM). One-touch dial is available only for the phone numbers with the location number 2 to 9 stored in the phonebook (SIM). Fast dialling Fast dialling is activated in Abbreviated Dialling Numbers (ADN) by entering a number 1 to 255 (depending on the SIM card), Fast dialling is also activated by entering the location number 1 to 500 of your phonebook (Phone) and then and . and . Displaying your own phone number (M0/M416) 0 or 416 Voice recall You can store up to 10 voice recall recordings which can be allocated to a personal data stored in the phonebook (Phone). To store the voice recall sound, see page 53. To use the voice recall function, use the following procedure: Press and hold When you use the headset, you can also activate the voice recall function by pressing and holding the button on it from the standby screen. Within 4 seconds, say the word or words you have recorded to identify the record you wish to recall. If the word or words were recognized, the first phone number of the personal data stored in the phonebook (Phone) will be called automatically. Options menu (during a call) During a call, 1 2 3 Main menu Hold/Retrieve Mute/Unmute to display the options menu Displays the Main menu screen. See "Overview of menu function" on page ix for details. Puts the call(s) on hold or retrieves the call(s). Mutes or unmutes all active calls. No. Options menu (during a call) 7 No. Options menu (during a call) (Continued) 4 5 6 7 8 Transfer call Add to conference Private call Record call Disconnect party Enables to transfer the call and connect other parties. After transferring the call, your call will be dropped. Merges calls and makes a multi-party call. Make a private call to the highlighted party within the multi-party call. Records the call while talking. Disconnects the highlighted party. Depending on the conditions, some options may be displayed in gray and not be available. Putting a call on hold To put the received or dialled call on hold, SK1 or 2. To retrieve the call, SK1 or 2 again. Mute You can mute the sound from the mouthpiece during a call. When your call is muted, the other party cannot hear any sound from your phone, but you can still hear the sound from the other party. To mute the sound during a call, press 3. To retrieve the sound, press 3 again. The mute function is automatically released after the call ends. Transferring a call When you have an active call and a held call, you can transfer the call and connect the two parties, then you can drop from the line while leaving those two calls active. To transfer the call, press 4. After dropping from the call with the other two parties, if you have a call waiting, you can proceed the call with it. Call transfer facility is SIM dependent. Multi-party calls If your SIM card is multi-party enabled, you can make a conference call to more than one caller. You can even leave the call while the remaining participants carry on with the call. 8 Receiving the second call SK1 or to accept the second call SK2 or 5 to merge both calls. When you accept the second call, the first call will be put on hold. to make the second call After the second participant answers, SK2 Making the second call SK1 to put the first call on hold Key in the phone number SK1 or or 5 to merge both calls. Putting the multi-party calls on hold SK1 or 2 to put both the first and second calls on hold To retrieve the call, SK1 or Making a private call 2 again. While on the multi-party call, you can make a private call to a specific party. Highlight the desired party you want to make a private call to 6 To end the private call and return to the normal multi-party call, While you are on a private call, other parties can continue with their conversation. 5. Ending the multi-party calls To end all calls, or SK2. To disconnect a specific party on a multi-party call, highlight the party you wish to disconnect Multi-party call facilities are network dependent. 8 Recording a call You can record the conversation during the call. During a call, press and hold or 7 to display the Voice memo screen SK1 to start the recording SK1 to pause and SK2 to stop the recording To play the recording, see "Recording/playing voice memo or setting speaker" on page 75 Call options (M43) From Call options, you can display the list of missed, received and dialled calls, the duration of the last call made and all calls, charge information and the redial blacklist 4 3 to display the Call options screen. No. 1 2 Call options Missed calls Received calls Displays the list of missed calls. You can also access this function by pressing from the standby screen. from the standby screen. 9 Displays the list of received calls. You can also access this function by pressing No. 3 4 5 Call options (Continued) Dialled calls Last call duration Total calls duration Displays the list of dialled calls. You can also access this function by pressing Displays the duration of the last call made on your phone. SK1 to reset the display to zero. Displays the duration of the total calls made on your phone. SK1 1 to reset the duration of the total dialled calls, 2 to reset the duration of the total received calls, or 3 to reset the duration of all calls. Displays the charge information (Advice of Charge - AOC). The AoC facility is SIM card and network dependent. To reset the display to zero, set the maximum charges or edit the unit price, you may be prompted to enter the PIN2 code. 1 2 3 Total charge Maximum charge Unit price Displays the total charge. SK1 to reset the display to zero. Displays the maximum charge. Key in the maximum number of units allowed SK1 Displays the unit price. Highlight the whole number (integer), the decimal number or the currency field Key in the required value for the whole number and decimal number fields. For the currency field, key in the currency type using a maximum of three characters SK1 from the standby screen. 6 Charge info 7 Redial blacklist Accesses the numbers in the blacklist. If dialled call is not successfully connected (e.g. number busy), the auto redial facility will be offered (see page 12). If you have set auto redial and the call still fails, the number called will be added to the blacklist. Depending on the conditions, some options may be displayed in gray and not be available. Display missed/received/dialled calls Options menu (M431M/M432M/M433M) or 4 3 1 for missed calls, or 4 3 2 for received calls, or or 4 3 3 for dialled calls. Highlight a number in the list No. 1 2 10 Missed calls/Received calls/Dialled calls Options menu Call Create message Calls the current number. Creates a new message to the highlighted phone number. No. 3 Missed calls/Received calls/Dialled calls Options menu (Continued) Add to phonebook Adds the current number to the phonebook. 1 to add it as a new personal data, 2 to add it to an existing personal data Press the appropriate number for the storage destination Press the appropriate number for the phonebook data field to copy the current number to. Deletes the current number. Deletes all the numbers in the list. Displays information on the current number. Creates a desktop icon of the selected number. Selects either to display 4 or 8 phone numbers in one screen. 4 5 6 7 8 Delete one Delete all Info Add desktop icon Items/Page Depending on the conditions, some options may be displayed in gray and not be available. Call settings (M16) From the Calls screen, you can change various call settings: the call diversion, call waiting and holding, auto redial and line identification. Call diversion (M161) Setting Call diversion 1 6 1 Highlight the type of call you wish to divert There will be a delay while your phone checks its divert status with your network. Highlight one of the conditions When the phone number field of a divert condition is highlighted, either enter the phone number to divert to, or delete any existing phone number. If you have made any mistake, highlight the appropriate field SK1 to clear any mistakes If the settings are correct, There will be a short delay while the network sends the divert status of your phone. There may be an additional charge for this service depending on your network. There may be unavailable settings depending on your network. Call diversion edit options menu Highlight the required edit field No. 1 Call diversion edit options menu Copy Copies the number in the edit field. 11 No. 2 3 4 5 Call diversion edit options menu Paste Disable all Phonebook Pastes the previously copied number. Disables the numbers from all the fields. Displays the phonebook to insert a number in the edit field. Add to phonebook Adds the number to the phonebook as a new personal data or saves the number in an existing personal data. Depending on the conditions, some options may be displayed in gray and not be available. Call waiting and holding (M162) This facility informs you that another call is being made to your phone while an existing call is in progress. Setting up call waiting 1 6 2 1 1 to activate, 1 2 to deactivate the call waiting, or 2 to check the status of call waiting. Using call waiting If you are on a call and another comes in, you will be alerted by a beep in the earpiece SK1 to accept the incoming call To switch the calls, SK1 To merge the calls, SK2 (see "Multi-party calls" on page 8) To end the current call, To retrieve the held call SK1 Auto redial (M163) With the auto redial facility, your phone will redial a number up to 10 times if the first attempt fails. A tone will be heard at each redial attempt. Your phone cannot connect a call if the other party is busy or if there are network problems. Pressing SK2 during a redial attempt will abort it. 1 6 3 1 to activate or 2 to deactivate the auto redial facility. Line ID (M164) The line ID (identification) facility is network dependent. The line ID facility enables you to choose whether or not to send your own phone number when you make a call and also whether or not to display a caller's phone number when you receive a call. 1 6 4 to display the Line ID screen with a over an activated line and a over a deactivated line. To set the status of each line (see the table on the right), highlight a line (the line will flash when selected). SK1 to set the line identification on or off to save the current settings. Line type Setting Outgoing Send own # Show connected # Incoming Show Incoming # Return own # 12 International dialling codes When you make an international call from any country, you must start by dialling a special international access code. Your phone has the facility to prefix a + symbol to the numbers, so that you need not enter the access code for the country that you are calling from. Entering international dialling codes Hold down 0. The 0 character displayed will change to a + character Key in the country code, area code, and phone number that you wish to call. International access country code + 44 area code 131 phone number 1234567 The UK country code is always 44, no matter what country you are dialling from. For example, a typical UK number of 0131 1234567 is entered as: Roaming You will be charged for calls forwarded to you while roaming. The roaming facility enables you to use your phone in many parts of the world and pay all charges through your normal service provider. Your network operator usually has agreements with named networks in other countries so that automatic roaming can take place with these named networks. The phone also allows you to set network preferences of your own. When dialling, you will need to add the international access codes if required. So, storing all numbers with the codes (such as +44 for UK) is helpful (see page 13). Before leaving your home country, you should select any preferences such as bar calls or call diversion. Setting Automatic or Manual network selection (M181) 1 8 1 1 to select the automatic mode or 2 to select the manual mode. Before you manually select a network, ensure it is covered under the agreement you have with your service provider. New search (M182) 1 8 2 to search the available networks Highlight the desired network Viewing/editing network list (M183) to connect to it Before editing your network list, please consult with your service provider. 1 8 3 to read the network list in the SIM memory Highlight the required network No. 1 SIM list Options menu Add Adds a new network to the list. 13 No. 2 3 SIM list Options menu Move Remove Moves the highlighted network within the list. Use and to move the network SK1 Deletes the highlighted network. Selecting the frequency band (M184) You have to select the frequency band to suit the location. 1 8 4 Select the required frequency band. Frequency bands must be adjusted to suit the location when roaming (Europe, US, etc.), for the phone to work properly. Text Entry This section describes how you enter text. The same method of text entry can be used in phonebook editing. Mode change With a text entry screen displayed, SK1 to change the text entry mode: T9® English text, Normal text (ABC), Numeric input T9® English text input Your phone incorporates T9® Text Input, enabling fast, easy and intuitive text input. For each letter to be keyed in, you only need to press the alphanumeric key once. The screen will display the word you may require based on the internal English dictionary of your phone. With a text entry screen displayed, SK1 until the entry mode is T9® English input. i) For example, to enter "Good": Press 4 6 6 3, and then press 0 to confirm the word. ii) To enter "Peter is good": Press to shift to upper case (for one letter). You will see a green arrow in the Help area. Press 7 3 8 3 7 to display "Peter", and then press 0 to confirm. Press 4 7 to display "is", and then press 0 to confirm. Press 4 6 6 3 to display "good", and then press 0 to confirm and the sentence is completed Key 0 SK1(List) 14 Function Confirms a word and inserts a space. Displays the list of other matching words. Key SK1(Spell?) SK2(Dismiss) SK2(Next) or # or 0 to 9 (press and hold) CLR (press and hold) # 0 0 to 9 (press and hold) CLR or # Function (Continued) Activates the spell mode which temporarily deactivates T9 for you to spell the word in Normal text input. The spell mode ends when you key in 0 to enter a space, or SK1(T9). Cancels the T9 matching word list. Displays the next candidate. Places the cursor. Inserts the number. Deletes any character. Toggles between lower case, shift (upper case for one letter) and caps lock (permanent upper case). Press and hold to activate the highlight mode (see "Highlight mode Options menu" on page 32 for details). Activates symbol mode when no word is highlighted. Normal text input With a text entry screen displayed, press SK1 until the entry mode is Normal text (ABC) input. Use alphanumeric keys to enter letters. For example, to enter "e", press 3 twice; to enter "f", press 3 three times. For other functions, see the table below. Key (press and hold) Function Toggles between lower case, shift (upper case for one letter) and caps lock (permanent upper case). Press and hold to activate the highlight mode (see "Highlight mode Options menu" on page 32 for details). Inserts a space. Inserts the number. Deletes any character. Places the cursor. Activates symbol mode. If you have made a mistake, use to place the cursor to the right of the incorrect character and then press CLR. When entering normal (ABC) text, and the character you require is displayed, use key to move to the next character position (if you wait for more than 1 second, the cursor will move one character to the right automatically). 15 Numeric input With a text entry screen displayed, press SK1 until the entry mode is Numeric input. You can also press and hold the number key to insert the number in T9/Normal text input mode. Use alphanumeric keys to enter numbers. Key allocations Whenever you need to enter text (for short messages, storing names with numbers, etc.), successive presses of an alphanumeric key will display different characters. Pressing in T9® English text input or Normal text (ABC) input toggles between lower case, shift (upper case for one letter) and caps lock (permanent upper case). When a text entry screen is displayed, pressing SK1 enables you to select Normal text input (ABC), T9® Text input (T9) or Numeric input (123). Depending on the types of text entry screens, not all types of text entry modes are available. Symbol mode In the symbol mode, pressing each key will input a symbol according to its position on the Symbols screen. By pressing # in a text entry mode, the Symbol screen will be displayed. Use and to select the row, and then press the appropriate number on the column of the required symbol. 16 IR Data Exchange Your phone is equipped with an InfraRed (IR) data port which enables you to send and receive phonebook/picture/video/sound excluding MP3/schedule/ ToDo list/note data with cellphones or other devices equipped with IR ports. Do not aim or direct the IR data port towards your or other people's eyes when using IR data exchange. Do not aim or direct the IR data port towards another IR device as this may cause the device to malfunction. Depending on the other party's cellphone or device, the data may not be received correctly. Positioning of the phones Open both sending and receiving phones vertically and place them as their IR ports face each other with less than 20cm of interval. Do not place anything between IR ports. The angle made of two IR ports must be within 30°. Do not move the phones until the data exchange is complete. The phones may not communicate successfully if they are placed under direct sunlight or fluorescent light, or close to other infrared devices. While sending or receiving data through IR, your phone is automatically placed out of service, so phone call, message and i-mode access are disabled. 15° or less mo 20c s r les IR send You can send phonebook/picture/video/sound excluding MP3/schedule/ToDo list/note data as a file through the IR port. Before starting to send data, the other party must be ready to receive data. Phonebook entry (M413...) You can only send Name, Home, Mobile, Work, Fax, 2 Email addresses and 2 pieces of descriptive information. Your phone sends data according to the vCard 2.1 specification. To display the phonebook (Phone), (for required number of times) or 4 1 3 Highlight a phonebook entry. 0 or 3 The phonebook entry will be sent through the IR port. Video/sound/picture file (M6...) 6 1 (Videos), 2 (Sounds) or 3 (Pictures) Highlight a folder Sounds) The file will be sent through the IR port. Highlight a file 2 3 (for Pictures/Videos) or 4 (for 17 Schedule entry (M84...) 8 4 Highlight a date Highlight a schedule entry 9 The schedule entry will be sent through the IR port. 7 The ToDo entry will be sent through the IR port. ToDo entry (M85...) 8 5 Highlight Public, Private or All Note (M862...) 8 6 2 Highlight a note Highlight a ToDo entry 2 and 2 The note entry will be sent through the IR port. IR receive (M891) You can standby your phone to receive data (phonebook/picture/video/sound (excluding MP3)/schedule/ToDo list/note data) from other devices or a phone of the same model. Receiving data through IR (M891) 8 9 1 Start sending data from the other end. Once the transmission completes, your phone automatically judges the type of received data and stores the data accordingly. If your phone does not have enough space to store the received data, a message will be displayed indicating lack of space. In such a case, delete unnecessary data and try the data exchange again. Received picture/video/sound files are stored in the Download folder of My data (see "My data (M6)" on page 61). IR modem (M892) You can use your phone as a modem for a PC via the IR port to establish a dial-up connection to an Internet service provider. Activating the IR port for modem use 8 9 2 The phone will be in standby status for IR transmission from the external device. If the IR transmission is not established within a short while, the standby status will end. While on active call or connecting to the external device such as USB, IR modem is not available. Your phone consumes a lot of battery power when used as a modem. After using your phone as a modem, be sure to deactivate the modem function from your PC or press (for the CSD connection only). When the modem function is deactivated, the idle screen will be displayed without the Infrared icon and GPRS icon. Check with your service provider to use your phone as a modem to connect to the Internet. 18 Desktop icons Desktop icons are shortcuts to functions or items. You can activate a desktop icon on the standby screen (desktop) in stead of following the menu and pressing the shortcut numbers. The desktop icons are displayed in two rows on the standby screen. See "LCD and displayed icons" on page vii for the actual location of the desktop icon area. There are two types of desktop icons: the automatically displayed and the manually created. Automatically displayed desktop icons The following automatically displayed icons are displayed on the upper row of the desktop icon area: Icon name Missed call Missed message Missed Mail Image Description Displayed when there is a new entry in the Missed calls list. Displayed when there is a new message you have not acknowledged. Displayed when there is a new Mail you have not acknowledged. You can delete all the automatically displayed icons by pressing and holding CLR on the standby screen. If you turn the phone off, all the automatically displayed desktop icons are deleted. Manually created desktop icons The following manually created icons are displayed on the lower row of the desktop icon area: Icon name Phone number Message URL Picture Notepad Camera Video Music player Image Description Displays a dialer screen with the registered phone number displayed. Creates a new message to the registered phone number or Email address. Activates the browser and accesses the registered URL. Displays the image file. Displays the Notepad preview screen with the note file displayed. Displays the camera view finder screen. Displays the video view finder screen. Displays the Music player screen. 19 Creating a desktop icon manually Activate the required function (camera/video/music player) or display the item (image file/note file/phone number/Email address/URL). to display the Options menu and select Add desktop icon (for an image/note file, this menu is under Use item, and for camera/video, under Other settings). You can create up to 10 desktop icons. If you have more than 5 desktop icons, an arrow will be displayed to indicate that you can scroll for more icons. The phone number, mail address or URL desktop icon data will not be updated when the original data is modified. Delete the old desktop icon and create a new one in such a case. When you create a desktop icon of an image file or notepad file, the data will be automatically protected. The default title will be the file name, even if this title is changed the original file name will remain the same. Each manually created desktop icon has a title that you can edit. Activating a desktop icon Highlight the required desktop icon If you do not press any key for three minutes after highlighting a desktop icon, the highlight is cancelled and the screen goes back to the normal standby screen. If you activate an automatically displayed desktop icon, it will be deleted automatically. Desktop icon Options menu Highlight a desktop icon No. 1 2 3 Desktop icon Options menu Edit title Delete one Delete all Edits the title of the highlighted desktop icon. Deletes the highlighted desktop icon. Deletes all the manually created desktop icons. 20 Settings (M1) Phone(M11) 11 No. Phone 1 Voice volume Adjusts the sound volume output from the earpiece. Use , Side keys or alphanumeric keys (0 to 9) to adjust the volume. You can also press the Side keys to display the volume control screen and to adjust the volume setting. During a call, you can press the Side keys to adjust the setting of the volume as required. 2 Answer options 1 Any key answer 2 Ring silencer On: Any key (except , SK2, the Side keys) is valid to answer a call Off: Only and SK1 are valid to answer a call On: Pressing one of the Side keys stops the ringer sound and the vibrator while receiving a call with the phone closed. This function cannot be used if the Side keys are locked. See also: "Mute" on page 8. On: You can answer an incoming call by opening your phone. on the standby screen. 3 Fold answer 3 Side key 4 ALS setup 5 Clock Disable: Side keys are locked while your phone is folded. You can also lock/unlock the Side keys by pressing and holding The Alternate Line Service (ALS) facility is SIM card and network dependent. If your SIM card supports ALS, you can setup which line to use for Outgoing call or Voice mail. 1 Show clock 2 Set time 3 Set date 4 Set date format 5 Set time format Sets to display the local time, both the local and remote times or no time on the main-LCD. Sets the time for the local or remote time. Sets the date. Selects the date display format. Selects the time display format from 12 hour or 24 hour. 21 No. Phone (Continued) 5 Clock (Continued) 6 Set timezone Sets the timezone. (A is placed on the currently selected timezone.) Highlight the required timezonePress SK1 to save the change. If the highlighted timezone has Daylight Saving, a check box will be displayed at the bottom of the screen. Press to activate ()/deactivate the setting. 6 7 Language LED Selects the language the phone displays. When you have switched the language to be displayed, please wait until the new setting becomes active. Selects the Light Emitting Diode (LED) colour for incoming calls/SMS/Mail or during a call. If the personal setting or the Group setting for the LED colour is also set in the phonebook, it has priority over this LED setting. (See "Allocating a LED colour" on page 53 for details.) Selects the earphone type from Stereo or Monaural, depending on your earphones (headset). 8 Earphone type Phone modes (M12) Your phone can be set to one of the following modes: Normal mode, Meeting mode, Pocket mode or Car mode. Any changes made to the settings while in a particular mode will be stored and used when that mode is selected again. Selecting your phone mode or 1 2 Press the appropriate key for the required mode. You can also set the Meeting mode or return to the previous mode by pressing and holding on the standby screen. Editing the mode settings or 1 2 Highlight the required mode SK1 Press the appropriate number for the required setting in the following table. For any volume setting, use , Side keys or alphanumeric keys (0 to 9). No. Phone mode setting 1 2 3 22 Ringer Ringer volume SMS tone Selects the Sound or Video for incoming calls. (See "Sounds (M62)" on page 62 or "Videos (M61)" on page 61 for details.) Sets the sound volume for incoming calls. While receiving a call with your phone open, the ringer volume can also be adjusted by pressing the Side keys. Selects the ringtone for incoming SMS messages. (See "Sounds (M62)" on page 62 for details.) No. Phone mode setting (Continued) 4 5 6 7 8 9 0 SMS tone volume Mail tone Mail tone volume Key tone Service tone Alarm volume Vibrator Earphone setting Auto answer # Sets the sound volume for incoming SMS messages. Selects the ringtone for incoming Mail or MMS messages. (See "Sounds (M62)" on page 62 for details.) Sets the sound volume for incoming Mail or MMS messages. Turns on/off the key tone. Turns on/off the service tone. Sets the sound volume for Clock alarm and Schedule alarm. Turns on/off the vibrator function. Selects the sound output from Earphone & Speaker or Earphone. Selects whether to answer an incoming call automatically. To use the Auto answer function, connect the headset to your phone and set the earphone volume to 1 or higher. If the earphone volume is set to 0, you must turn the vibrator ON to use the Auto answer. If the selected mode is Car mode, the backlight will always be turned on. This will reduce battery life. Main-LCD (M13) 1 13 No. Main-LCD Greetings Selects the greeting which is displayed on the main-LCD during phone start-up from No greeting, Text or Animation. If you select Text greeting, press SK1 to edit the greeting text. Key in a greeting text and press . Selects a picture or video file to use as the background for the main-LCD. Selects and resets the background and icons for the Main menu screen. Selects the phone's colour theme. 2 3 4 Wallpaper Main menu style Colour style 2nd-LCD (M14) 14 23 No. 2nd-LCD 1 2 Clock/Event display Clock orientation Selects which items to display on the 2nd-LCD from Clock & Event, Clock only, Event only or Off. Selects whether to display a horizontal clock or a vertical clock. When you select to display a vertical clock, it is read from the camera and LED end. The event displays and incoming call numbers are shown along the long end according to the Display direction. Turns on/off the function to display the incoming call number on 2nd-LCD. Selects which direction to display the 2nd-LCD. This setting does not effect the vertical clock. Sets the contrast level of the 2nd-LCD. 3 4 5 Incoming call No. Display direction Contrast Power saving (M15) 15 If the selected mode is Car mode, this function is displayed in gray and is not available. No. 1 Power saving Level setting Selects the power saving level from Level 1 (minimum power save setting), Level 2 (moderate) or Level 3 (maximum). The main-LCD backlight will turn dim and then turn off after a given amount of time with no operation. When the phone is folded, Power saving level also applies to the 2nd-LCD. Selects whether to flash the LED of SK1 and SK2 when the main-LCD and its backlight are turned off. If the selected mode is Car mode or the camera view finder screen is displayed, the main-LCD backlight will always be on. 2 Function key LED Calls (M16) 16 For settings provided on the Calls screen, see "Call settings (M16)" on page 11.