User manual NEC VT40 - QUICK GUIDE

Quick Connect Guide Step 1 Connect the supplied 15pin-15pin signal cable. M E MultiSync VT Series LCD Projectors Step 4 R C E A Set up the Projector. To adjust the projector's focus or to zoom in and out use the Focus ring or Zoom lever on the lens. For older Macintosh computers, use the supplied pin adapter to connect to your Macintosh's video port. PC -CO RG INP B UT RG BI NP UT AU DIO OU TP UT RG IDE Focus ring BINO OU T OU UT T P IN VID EO RG INP B UT AU OU PC D NT RO L S-V UT O Zoom lever TP UT IN OU T -CO NT RO L S-V IDE O VID Always power down before you hook up. Monitor Step 2 Connect the supplied power cable. Adjusting the Tilt Foot 1. Press and hold the Tilt button on the front of the projector. 2. Lift the front edge of the projector to the desired height, and release the button to lock the Adjustable Tilt Foot. To fine-tune the image's position vertically on the screen, rotate the foot. Each of the rear feet height can be changed up to 0.6" (4 mm). RG INP B UT AU OU PC D TP UT IN OU T -CO NT RO L S-V IDE O VID P O W E R S TA TU S Step 3 Turn on the projector. S U O C R E Power button ME CA NCEL NOTE: To turn off the projector, press and hold the POWER button for a minimum of two seconds. · If the projected image does not appear square to the screen then use keystone correction for proper adjustment. Printed in Japan 78038752 NU ENTER O N /O FF CA N C EL S E LE C T R S O U M E C E A U TO A D JU S T RG INP B UT AU D A NU OU PC U TO A JU D TP UT IN OU T S E -CO ENT E R NTR LE C S T OL S-V S TA TU S R E P O W IDE T O VID O /S N TA N D B Y Basic Menu Source Select RGB Video S-Video Picture Brightness Contrast Color Hue Sharpness Volume Image Options Keystone Color Temperature Lamp Mode Menu Menu Mode Language Projector Pointer Source Display Volume Bar (Direct Button) Remote Control Features (12) (1) (3) (5) (6) Cancel Button SOURCE AUTO ADJ. (2) ME NU Vol. Press this button to exit "Menus". Press this button to return the adjustments to the last condition while you are in the adjustment or setting menu. (7) Magnify Button SELECT L Vol. (4) CE Basic Menu Source Select Picture Volume Image Options Menu Setup Help ER CA N (6) (9) (11) (7) High-Bright / Eco POINTER MAGNIFY HELP PIC. MUTE POWER (8) (10) RD-366E Use the (+) or (­) button to adjust the image size up to 400%. When the Pointer is displayed, the magnified image is displayed at the center of the Pointer. When the Pointer is not displayed, the magnified image is displayed at the center of the screen. When the image is magnified, the pointer is changed to the magnifying icon. (8) Pointer Button Setup Orientation Background Help Contents Information Basic / Advanced English / German/ French/ Italian/ Spanish / Swedish / Japanese Pointer 1- 8 (1) Source Button On / Off Press to select a video source. On / Off (2) Auto Adjust Button Use this button to adjust Position-H/V and Pixel Clock/Phase for an optimal picture. Front Floor / Rear Ceiling / Rear Floor / Front Ceiling Blue / Black / Logo (3) Menu Button Displays the menu. Contents Pege 1(Source Name / Input Terminal / Horizontal Frequency / Vertical Frequency / Sync Polarity) Pege 2 (Signal Type/Video Type/Sync Type / Interlace / Resolution) Page 3 (Aspect Ratio / Gamma Correction / Noise Reduction / Color Matrix / Matrix Type) Page 4 (Lamp Hour Meter / Projector Usage) (4) Select ( ) / Volume (+) (­) Buttons :Use these buttons to select the menu of the item you wish to adjust. :Use these buttons to change the level of a selected menu item. A press of the button executes the selection. When no menus appear, these buttons work as a volume control. When the pointer is displayed, these buttons move the pointer. Use this button to enter your menu selection. (5) Enter Button NOTE : The POWER, SOURCE. AUTO ADJ., MENU, SELECT, ENTER and CANCEL buttons on the remote control perform the same functions as the corresponding buttons on the projector cabinet. The remaining buttons are on the remote control only. EN T Press this button to display one of the eight pointers; press again to hide the pointer. You can move your pointer icon to the desired area on the screen using the Select button. (9) Picture Mute Button This button turns off the image and sound. Press again to restore the image and sound. (10) Help Button Provides information about operation and adjustment procedures, the set-up information for the current menu and adjustment information during menu operation. This also displays information on how to use the Help menu. (11) Power Button Use this button to turn your projector on and off. NOTE: To turn off the projector, press and hold the Power button for a minimum of two seconds. (12) Infrared Transmitter Direct the remote control toward the remote sensor on the projector cabinet.