User manual NEFF S44M46

en Summary of instructions for dishwasher Brief and handy: everything your dishwasher needs... Before using for the first time, read the installation and operating instructions! Set the water softening system * Find out the water hardness at your water utility company and enter Read off the setting ... Quickly sorted ... and then set A B Reset C ­ Hold down programme button B and switch on the main switch, then release the buttons. The display of button B and the number 4 set by the factory flash. ­ Each time button B is depressed, the setting increases by one; if 7 has been reached, the display jumps back to 0. ­ Switch off the main switch. The selected setting has been stored in the appliance. * only before using the dishwasher for the first time or if the water hardness changes Fill with special salt Dissolves limescale (not required for set value 0!) Unscrew the lid. Only before using the dishwasher for the first time pour approx. 1 l / 2 pt water into the salt opening. Pour in max. 1.5 kg / 3 lb 5 oz salt (never detergent!) Screw on the lid. Switch on dishwasher immediately. Fill with rinse aid Everything is sparkling clean ... Press mark 1, lift up lid 2. Refill whenever level indicator is light! Pour in rinse aid. Close the lid. CLICK! Fill with detergent Very dirty dishes, a lot of detergent ... If required, open the lid (press the pin). Warning, combination products are not suitable for all programmes, follow manufacturer's instructions. Pour in detergent. Push the lid shut, press. PLOP! Select programme Quick, economical or intensive ... Programme overview This overview lists the max. possible number of programmes. The programmes supplied with your appliance are indicated on the fascia. Duration in minutes Intensive 70_ Auto 55_ /65_ Eco 50_ Gentle 40_ Quick 45_ Prerinse 630G 9000 156 033 ( 8601) The programme data are values measured in the laboratory in compliance with Standard EN 50242. Deviations is practice are possible. Electricity consumption in kWh Water consumption in litres with Aquasensor 138 1,65 16 13 85-140 1,10-1,60 10-17 ­ 140 1,05 12 ­ 75 0,90 14 11 30 0,80 10 ­ 19 0,05 4 ­ Switch on appliance Press On/Off switch, running time of the chosen programme appears Additional programmes ** Time selection Saving time (VarioSpeed) ... is obtained by increased energy consumption at a constant cleaning and drying performance. Flexibility ... Half load ... for a few items, saves water, energy and time Switch off the appliance Everything O.K... When the display shows 0 (end of programme), press On/Off switch h. ...switches on as soon as you press the time selection button: Alters the programme start in hourly steps ** some models Maintenance and care Strainers ... Check, if required, clean Rotate filter cylinder, remove filter system ... For perfect rinsing results ... rinse under flowing water ... Insert ... Screw in filter system NOTE MARK! Cleaning the waste-water pump * * With some models ­ Ladle out water and remove filters ­ Unscrew cover (Torx T20) ­ Check area of fan impeller for foreign objects ­ Screw in cover and insert filters Spray arms ... Remove blockages/deposits Pull lower arm upwards ... Unscrew upper arm ... Clean spray nozzles under flowing water (perhaps with toothpick) ... Insert lower arm ... Screw in upper arm Rectifying minor faults yourself ... Fault Possible causes ... as it is worth doing it yourself! Remedial action Fault Possible causes Remedial action Separate the utensils, prevent contact points. Follow manufacturer's instructions (detergent). Select a more intensive programme. Clean the spray arms (see above). Clean the filters (see above). Arrange the utensils so that the spray arms can rotate freely. Residual water in the appliance Waste water pump blocked The programme has not yet ended Clean waste-water pump (see above). Close appliance and switch on. or terminate programme (see Terminating the programme). Utensils are not clean Sand or gritty residue on the utensils Utensils are situated close together or one above the other Too little detergent Unsuitable programme selected Appliance is not running / stops Check water supply Display lights up Supply fitting not open Supply hose kinked Supply fitting jammed or calcified Open supply fitting. Install supply hose without kinks. 1. Unscrew water connection. 2. Clean filter in the water connection. 3. Flow rate must be min. 9 l/min. when water supply is open. If the flow rate is less, replace the supply fitting. Spray arm nozzles blocked Filters dirty, not seated firmly Spray arms blocked Stains and streaks Rinse-aid dosage too high / too low Streaks: reduce dosage. Water or limescale stains: increase dosage. Milky film on the utensils (removable) Plastic / utensils discoloured Too little detergent Discoloration caused by food colourings (tomato sauce) Follow manufacturer's instructions (detergent). Discoloration is harmless; subsequent rinse cycles will cause it to fade. Milky film, glasses cloudy / dull (not removable) Water softening system incorrectly set; No salt Glasses not dishwasher-proof. Correctly set water softening system. Refill with salt. Use dishwasher-proof glasses. Use a detergent suitable for glasses. Rust on the cutlery Cutlery not rust-resistant Hard knife blades are more susceptible Extraneous rust Use dishwasher-proof cutlery. Never wash rusting parts in the appliance. More information can be found in the operating instructions Stopping the programme ... Press and hold the two reset buttons simultaneously for approximately 3 seconds while the programme is running (RESET) Loading the dishwasher correctly ... "0" appears The programme will stop after 1 minute Switch off the appliance. Arrange dishwasher-proof utensils (having removed any ash, wax, grease, ink, sticky labels; remove, large remnants of jam, dairy products and food) according to the operating instructions and check that the spray arms can rotate freely.