User manual NETGEAR AGM731F

R Everybody's connecting. TM SFP GBIC Module AGM731F The Small Form-factor Pluggable (SFP) Gigabit interface Converter (GBIC) slots on NETGEAR's managed switches provides you with a highly adaptable network. You have the option of building your network for copper and/or fiber gigabit connections. Due to the automatic detection capabilities of the switch, installation of the SFP GBIC only requires that you plug the module into the module slot. Plugging an AGM731F module will disable the associated RJ-45 port. Installing a SFP GBIC module: Insert the module into the slot, pressing firmly to seat the module. You should hear a 'click' when the module is firmly seated. Removing a SFP GBIC module: Release the module latch by pushing on the tab on the bottom of the module while pulling on the module. Trademarks ©2003 NETGEAR, Inc. NETGEAR, the Netgear logo, The Gear Guy, Auto Uplink and Everybody's Connecting are trademarks or registered trademarks of Netgear, Inc. in the United States and/or other countries. Other brand and product names are trademarks or registered trademarks of their respective holders. Information is subject to change without notice. All rights reserved. Statement of Conditions In the interest of improving internal design, operational function, and/or reliability, NETGEAR reserves the right to make changes to the products described in this document without notice. NETGEAR does not assume any liability that may occur due to the use or application of the product(s) or circuit layout(s) described herein. Certificate of the Manufacturer/Importer It is hereby certified the NETGEAR Model AGM731F has been suppressed in accordance with the conditions set out in the MBPT-AmtsblVfg 243/1991 and Vfg 46/1992. The operation of some equipment (for example, test transmitters) in accordance with the regulations may, however, be subject to certain restrictions. Please refer to the notes in the operating instructions. Federal Office for Telecommunications Approvals has been notified of the placing of this equipment on the market and has been granted the right to test the series for compliance with the regulations. EN 55 024 Declaration of Conformance This is to certify that the NETGEAR Model AGM731F is shielded against the generation of radio interference in accordance with the application of Council Directive 89/336/EEC, Article 4a. Conformity is declared by the application of EN55 024 Class A (CISPR 22) FCC Compliance Notice: Radio Frequency Notice Federal Communications Commission (FCC) Compliance Notice: Radio Frequency Notice This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: - This device may not cause harmful interference. - This device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a commercial installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case users will be required to take whatever measures may be necessary to correct the interference at their own expense. Warning Warning Class 1 laser product. Warning Class 1 LED product. Warning Because invisible laser radiation may be emitted from the aperture of the port when no fiber cable is connected, avoid exposure to laser radiation and do not stare into open apertures. Specifications Standards IEEE802.3z 1000BASE-SX Gigabit Ethernet (Forced full-duplex mode) 0.38 x 0.53 x 2.56 in (0.96 x 1.343 x 6.5 cm) LC for 62.5um or 50um cable 0.11 lb (0.05 kg) 32 to 1040 F (0 to 400 C) 14 to 1580 F (-10 to 700 C) Dimensions (H x W x D) Connectors Weight Operating temperature Storage temperature Operating relative humidity 10 to 90% noncondensing Operating altitude Power consumption MTBF Safety Certifications up to10,000 ft (3000 m) 500 mW 45 years UL1950 CSA 22.2 No. 950 R Everybody's connecting. TM M-10145-01