User manual NETGEAR FS309T - Installation Guide

Introduction The NETGEAR® Model FS309T Fast Ethernet Switch provides you with a low-cost, high-performance network solution and is designed to support power workgroups operating at either 10 megabits per second (Mbps) or 100 Mbps, and can relieve server and backbone bottlenecks with one copper Gigabit Ethernet port. Applications Desktop Switching The Model FS309T switch, used as a desktop switch to build a small network that enables users to have Gigabit (1000 Mbps) access to a server. Key 1000 Mbps 100 Mbps 10 Mbps Server with Model GA302T Gigabit Card 3 Connecting Devices Type Technical Specifications Specification ISO/IEC 802-3 (ANSI/IEEE 802.3i) 10BASE-T Ethernet IEEE 802.3u,100BASE-TX Fast Ethernet IEEE 802.3ab, 1000BASE-T Gigabit Ethernet compatible with major network software, including Windows® networking, NetWare, and Linux 100 Mbps with 4B/5B encoding and MLT-3 physical interface for 100BASE-TX 10 or 100 or 1000 Mbps half-duplex 20 or 200 or 2000 Mbps full-duplex RJ-45 connector for 10BASE-T or 100BASE-TX or 1000BASE-T Ethernet interface 3.7 w max Standards Compatibility To connect devices to the switch: 1. Connect the devices to the 10/100 Mbps ports on the switch, using Category 5 UTP cable and an RJ-45 plug. Note: Ethernet specifications limit the cable length between your PC or server and the switch to 328 feet (100 meters) Verify Package Contents Model FS309T Fast Ethernet Switch Model FS309T Switch Data Rate 2. Connect one end of the Category 5 UTP cable to the Gigabit port and the other end to the linking server or network device. 3. Connect one end of the AC power cord to the power receptacle on the rear panel of the switch and the other end of the AC power cord to the wall outlet. Network Interface Power 9 8 7 6 5 4 3 2 1 100-240VAC, 50-60Hz Installation Hardware Installation Guide, Warranty & Registration Card and Support Information Card Power code (for switch) 9607FA Physical Specifications Segment Switching The Model FS309T switch can segment a network into multiple connected pieces, increasing overall bandwidth and throughput. The Model FS309T switch segmenting networks that are built with a NETGEAR Model FE508 Fast Ethernet Hub and a NETGEAR Model DS516 Dual Speed Hub. Key 1000M 4 Verifying Installation When power has been applied to the switch: · The green Pwr (power) LED on the front panel is on. When the switch is connected and operating, refer to the table in "LEDs" for information about the LEDs and their activity. Dimensions: Weight: 25.3 x 3.5 x 18.0 cm 2.86 lb; 1.30 kg Environmental Specifications Operating temperature: Operating humidity: Electromagnetic Compliance 0 to 40° C (32 to 104° F) 90% maximum relative humidity, noncondensing CE mark, commercial; FCC Part 15, Class A; EN 55 022 (CISPR 22), C-Tick, VCCI A CE mark, Commercial UL listed (UL 1950) Product Illustration Front Panel of the Model FS309T Switch 10M/100M Link, Activity LED 1000M Link, Activity LED Server with Model GA302T Gigabit Card 10/100Mbps Fast Ethernet Switch with Gigabit Port Ethernet PWR 1 MODEL GREEN = 100M, YELLOW = 10M, BLINKING = ACT FS309T 2 3 4 5 6 7 8 9 GREEN = FDX, YELLOW = COL 1000 Mbps 100 Mbps 10 Mbps Model FS309T Switch Troubleshooting Information Symptom Power LED is off. Cause No power is received at the hub. Solution Check the power cord connections for the switch and the connected device. Check for a defective adapter card, cable, or port by testing them in an alternate environment where all products are functioning. Power LED FDX LED Collision LED 9 8 7 6 5 4 3 2 1 Safety Agency Approvals for the Power Adapter 100-240VAC, 50-60Hz Rear Panel of the Model FS309T Switch Model FE508 Fast Ethernet Hub Model DS516 Dual Speed Hub Performance Specifications Frame filter rate: 14,800 frames/sec max for 10M port 148,000 frames/sec max for 100M port 1,480,000 frames/sec max for 1000M port 14,800 frames/sec max for 10M port 148,000 frames/sec max for 100M port 1,480,000 frames/sec max for 1000M port 100 Mbps to 100 Mbps: 9.5 µs max 100 Mbps to 1000 Mbps: 8.5 µs max 1000 Mbps to 100 Mbps: 3.2 µs max 4000 MAC addresses 48-bit MAC address 128 kilobytes 9 8 7 6 5 4 3 2 1 100-240VAC, 50-60Hz Gigabit Port 10/100M Port Power Socket 9462FA Frame forward rate: Network latency (using 64-byte packets): Address database size: Addressing: Queue buffer: Auto UplinkTM The Auto Uplink technology that NETGEAR has included in this product will automatically sense whether the straight-through cable plugged into any port should have a `normal' connection, e.g. connecting to a PC; or an `uplink' connection, e.g. connecting to a router, switch, or hub. That port will then configure itself to the correct configuration. This feature also eliminates the need to worry about crossover cables, as Auto Uplink will accommodate either type of cable to make the right connection. Note: Auto Uplink will compensate for setting uplink connections, and crossover or straight-through cables. Using Auto Uplink to create multiple paths between any two network devices will disable your network. 9608FA Make sure all cables used are correct and comply with Ethernet specifications. Either 10M, 100M, or 1000M Link LED is off Port connection is not functioning. Check the crimp on the RJ-45 connectors, and make sure that the plug is properly inserted and locked into the port at both the switch and the connecting device. Make sure all cables used are correct and comply with Ethernet specifications. One or more components are malfunctioning. A segment or device is not recognized as part of the network. Not all system Test the components in an components are alternate environment where all properly installed. other components are functioning properly. One or more devices are not properly connected or cabling does not meet Ethernet guidelines. Verify that the cabling is correct. Be sure all cable connectors are securely positioned in the required ports. Straight-through cables should be used for all standard twisted pair connections. Make sure all devices are connected to the network. Equipment may have been accidentally disconnected. 1 Preparing the Site Before you begin installing your switch, prepare the installation site. Make sure that your operating environment meets the operating environment requirements of the equipment. Characteristic Temperature Requirement Ambient temperature between 0 and 40 C (32 and 104 F). No nearby heat sources such as direct sunlight, warm air exhausts, or heaters. Maximum relative humidity of 90%, noncondensing. Minimum 2 inches (5.08 cm) on all sides for cooling. Adequate airflow in room or wiring closet. At least 6 feet (1.83 m) to nearest source of electromagnetic noise (such as photocopy machine). Adequate power source within 6 feet (1.83 m). Operating humidity LEDs This table describes the activity of the Model FS309T switch LEDs. Label PWR Activity Description On Off The Switch is receiving power The Switch is NOT receiving power Indicates Link or Activity at 10 Mbps or 100 Mbps · 100 Mbps speed Link · 100 Mbps speed Activity · 10 Mbps speed Link · 10 Mbps speed Activity Indicates Link or Activity at 1000 Mbps · 1000 Mbps speed Link · 1000 Mbps speed Activity Full Duplex Collision Color Green Ventilation Operating conditions 100M/10M On Power GREEN GREEN-Blinking YELLOW YELLOW-Blinking 2 Installing the Switch 1000M On GREEN GREEN-Blinking Set the switch up on a flat surface; you do not need any special tools. Be sure the switch is positioned with at least 2 inches of space on all sides for ventilation. FDX/COL On GREEN YELLOW-Blinking © 2001 by NETGEAR, Inc. All rights reserved. Trademarks NETGEAR is a registered trademarks of NETGEAR, Inc. in the United States and in other countries. Microsoft, Windows, and Windows NT are registered trademarks of Microsoft Corporation. All other trademarks and registered trademarks are the properties of their respective owners. All rights reserved. Information subject to change without notice. Statement of Conditions In the interest of improving internal design, operational function, and/or reliability, NETGEAR reserves the right to make changes to the product described in this document without notice. NETGEAR does not assume any liability that may occur due to the use or application of the product(s) or circuit layout(s) described herein. Certificate of the Manufacturer/Importer VCCI Statement This equipment is in the Class A category (information equipment to be used in a residential area or an adjacent area thereto) and conforms to the standards set by the Voluntary Control Council for Interference by Data Processing Equipment and Electronic Office Machines aimed at preventing radio interference in such residential areas. When used near a radio or TV receiver, it may become the cause of radio interference. Read instructions for correct handling. Federal Communications Commission (FCC) Compliance Notice: Radio Frequency Notice This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: · This device may not cause harmful interference. · This device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commerical environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. · Consult the dealer or an experienced radio/TV technician for help. EN 55 024 Declaration of Conformance Installation Guide Please register online. YOU MUST REGISTER TO OBTAIN TECHNICAL SUPPORT. PLEASE RETAIN PROOF OF PURCHASE and this warranty information. To register your product, get product support, or to obtain product information and NETGEAR product documentation, direct your Web browser to the http://www.NETGEAR.com Web page. If you do not have access to the World Wide Web, you can register your product using the enclosed registration card and mail it to NETGEAR customer service. Go to http://www.NETGEAR.com for the NETGEAR Web page. Defective or damaged merchandise can be returned to your point-of-sale representative. See Support Information Card for phone numbers. November, 2001 M F S 3 0 9 T N A 0 It is hereby certified that the NETGEAR Model FS309T Fast Ethernet Switch has been suppressed in accordance with the conditions set out in the BMPT-AmtsblVfg 243/1991 and Vfg 46/1992. The operation of some equipment (for example, test transmitters) in accordance with the regulations may, however, be subject to certain restrictions. Please refer to the notes in the operating instructions. Federal Office for Telecommunications Approvals has been notified of the placing of this equipment on the market and has been granted the right to test the series for compliance with the regulations. This is to certify that the NETGEAR Model FS309T Fast Ethernet Switch is shielded against the generation of radio interference in accordance with the application of Council Directive 89/336/EEC, Article 4a. Conformity is declared by the application of EN 55 024 Class A (CISPR 22). Canadian Department of Communications Radio Interference Regulations This digital apparatus (NETGEAR Model FS309T Fast Ethernet Switch) does not exceed the Class A limits for radio-noise emissions from digital apparatus as set out in the Radio Interference Regulations of the Canadian Department of Communications. Règlement sur le brouillage radioélectrique du ministère des Communications Cet appareil numérique (NETGEAR Model FS309T Fast Ethernet Switch) respecte les limites de bruits radioélectriques visant les appareils numériques de classe A prescrites dans le Règlement sur le brouillage radioélectrique du ministère des Communications du Canada. Fast Ethernet Switch with Gigabit Port 10/100/1000 Mbps Fast Ethernet FS309T Phone: 1-888-NETGEAR E-mail: support@NETGEAR.com www.NETGEAR.com NETGEAR, Inc. 4500 Great America Parkway Santa Clara, CA 95054 USA Internet / World Wide Web Support Information IMPORTANT!