Owner's Manual MEDIAMASTER 9200 S 9600 S GB 1 Important Information Wiring the plug (UK and Eire only) The mains lead on this product is already fitted with a non-rewireable (moulded) plug incorporating a fuse, the value of which is indicated on the pin face of the plug. Should the fuse need to be replaced, an ASTA or BSI approved BS 1362 fuse must be used of the same rating, marked thus: If the fuse cover is detachable always refit the cover after replacing the fuse. NEVER use the plug with the fuse cover omitted. If the fitted plug is not suitable for your socket outlets it should be cut off, after having first removed the fuse, and an appropriate plug fitted in its place. If this new plug contains a fuse its value should be the same as that removed from the non-rewireable plug. The severed plug must be destroyed immediately to avoid the possible shock hazard should be inserted into a 13A socket elsewhere. If you need to replace the mains plug then follow the instruction given below: The wires in the mains lead are coloured in accordance with the following code: BLUE - Neutral (N); BROWN - Live (L). As these colours may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: The wire coloured BLUE must be connected to the terminal marked with the letter N or coloured BLUE or BLACK. The wire coloured BROWN must be connected to the terminal marked with the letter L or coloured BROWN or RED. On no account either of these wires to the terminal marked E or coloured GREEN or GREEN and YELLOW. Before replacing the plug cover, make certain that the cord grip is clamped over the sheath of the lead; not simply over the two wires. If in doubt, consult a competent electrician. GB 2 Mediamaster 9200 S and 9600 S The sky is the limit with your Mediamaster. It`s easy to use, always at your command and adaptable for future advances. To begin with, you will find it necessary to read these instructions but you will soon find yourself competent without them. Contents For your safety Rear panel, Front panel Installation of the Mediamaster Connecting the Mediamaster to different units Preparing the remote control Switching on for the first time Before you continue ..... Remote control About the Smart Card and CA Module Basic Settings The Welcome Menu Antenna configuration Channel Search SMATV or IF frequency channel search Viewing TV Important general information Start/stop watching TV Select Channel Programme Information. The "i" Button TV Guide The Radio button List of TV channels / Radio channels Video recorder Analogue Receiver Subtitling and Teletext. The TEXT button Settings from the Main Menu The TV Guide and Radio Guide Parental Control Installation Submenus Antenna Configuration and Channel Search Advanced Channel Search Edit TV and Radio Channels Language Settings System Settings Receiver upgrade Automatic Installation Symbols on the Mediamaster display Glossary of terms Problem solvings Technical Specifications 3 4 5 5 7 8 8 9 10 11 11 11 12 15 16 16 16 16 16 17 17 18 19 19 19 20 20 21 22 22 22 23 23 23 24 24 24 25 26 27 For your safety · Keep a clear space around the Mediamaster to allow for sufficient ventilation. · Do not cover the Mediamaster or place it on a unit that emits heat. · Use a soft cloth and a mild solution of washing-up liquid to clean the casing. · Nokia is proud to offer a high quality product. To keep this level of quality, service should be carried out only at a Nokia authorised service centre. · Do not connect or modify cables when the Media-master is plugged in. · Do not remove the cover. · Do not allow the unit to be exposed to hot, cold or humid conditions. · Please note that the only way to isolate the Mediamaster completely from the 230 V mains supply is to unplug the mains lead! We reserve the right to change specifications. Please be aware that new software can change the functionality of the Box. DiSEqCTM is a trademark of EUTELSAT The EMC Directive 89/336/EEC is applied to this product. GB 3 Rear panel Mains lead 230 V AC +/- 15%, 50 Hz 0/12 VOLT for an external LNB switch TV SCART for the audio / video input of the TV set SAT SCART for an analogue receiver LNB * Satellite dish input (Fconnector) AUDIO L R Stereo outputs for connection to a HiFi system VCR SCART for a video recorder RS232 for a printer, PC or a high speed modem SCSI For a CD-ROM player or other high-speed data equipment * LNB cables also feed the LNB with a supply voltage of 13/18 V (V/H polarisation) and a 0/22 kHz signal for LNB switch Front panel Display shows programme information. At start up, it displays software and boot/loader number Welcome Slot for the CA module and the Smart Card (9600 S) Slot for the Smart Card (9200 S) to turn the receiver on/ off (standby) Select channel number, up/down GB 4 Installation The box for your Mediamaster should contain the following items: · the Mediamaster 1 4 2 5 8 3 6 9 · a remote control handset with batteries. · a fully featured SCART cable which can be used to connect your Mediamaster to the TV or video recorder. · Owner's Manual. TV 7 0 GUIDE MENU EXIT OK TEXT SCART cable About the SCART sockets · On the back side the Mediamaster is equipped with 3 SCART sockets (see figure). When you connect external sets to any of theese sockets, always use fully featured SCART cables. There are "slimmed" (=cheap) SCART cables on the market, but it is not sure that e. g. your videorecorder will work OK with some of these cables. · SCART cables are also necessary to get stereo sound from a stereo TV and video recorder. SCART socket Connecting the Mediamaster to the satellite dish Installing the satellite dish · Your satellite dish should be installed with a cable for you to connect to the Mediamaster. If you do not have this cable you will need to buy one from a dealer (tell the dealer you need a coaxial cable and F-connectors). · Connect the cable from the satellite dish to the socket marked "LNB"on the back of the Mediamaster. 15 mm If you need to fit the F-connectors onto the cable · Prepare each end of the cable as shown in the diagram. You will need to fold back the outer braid (as shown). · Slide the F-connector onto the cable, then turn it clockwise until it grips the braid. · Ensure that 3 mm of the core is protruding from the end of the connector. 8 mm F-connector 3 mm GB 5 Connecting the Mediamaster to a TV set · Do not remove the cable from the TV to the TV aerial. · Connect one end of the SCART cable to the TV SCART socket on the back of the Mediamaster and the other end to the SCART input socket on your TV. TV SCART Connecting to a TV and a video recorder Refer to your video recorder manual for full instructions. · Connect one SCART cable between the TV and the TV SCART socket on the Mediamaster. · Connect the other SCART cable between the video recorder and the VCR SCART socket on the Mediamaster. · Connect the RF cable from the RF output on the video recorder to the TV aerial input on the TV. · Connect the ordinary TV aerial directly to the RF input socket on the video recorder. Connecting to a Hi Fi system · Connect an RCA/Cinch stereo cable from the AUDIO L R sockets on the Mediamaster to the LINE, AUX, SPARE or EXTRA input sockets on your Hi Fi system. GB 6 Connecting to an analogue satellite receiver and a video recorder · Connect one SCART cable between the TV set and the TV SCART socket on the Mediamaster. · Connect one SCART cable between the TV SCART socket on the analogue satellite receiver and the SAT SCART socket on the Mediamaster. · Connect one SCART cable between the video recorder and the VCR SCART socket on the Mediamaster. · Connect the RF cable from the RF output on the video recorder to the TV aerial input on the TV. · Connect the ordinary TV aerial directly to the RF input socket on the video recorder (TV if no VCR). With Video recorder NOKIA Smart priority switch B A VCR In order to switch the signal from the dish between the analogue and digital receivers, you need a Nokia Smart priority switch (at A B in the diagram). · Connect the coaxial cable between output A on the NOKIA Smart priority switch (accessory) to the LNB socket on the analogue receiver. · Connect the coaxial cable between output B on the NOKIA Smart priority switch (accessory) to the LNB socket on the Mediamaster. The analogue receiver must switched OFF when you want to watch channels from the Mediamaster. Analogue receiver Nokia Smart Priority Switch Without a VCR, you should connect as shown in the diagram to the right. B A Analogue receiver Preparing the remote control · Remove the cover on the battery compartment at the bottom of the remote control handset. · Insert the 2 x AAA (1,5 V) batteries, as shown in the diagram, taking care to observe the + and - markings indicated inside. · Replace the cover. GB 7 CA module and Smart Card. Model 9600 S only CA modules and Smart Cards are licenced to Service Providers. If you want to watch TV programmes from a Service Provider you must use a CA module (Conditional Access) with a Smart Card. Please note, that the CA module and the Smart Card may give special menus not described in this Manual. If no CA module is used you can only watch "free to air" TV programmes. Note: The mains plug must not be plugged in before inserting the CA module! · Insert the CA module fully into the slot behind the lid in the front panel of the Mediamaster so that the arrow on the module faces upwards and inwards. · Insert your card fully into the slot on the CA module, so that the microchip (the yellow spot) faces upwards and inwards. Switching on for the first time You can now plug in the mains plug of the Mediamaster to the wall socket. · Switch on your TV set. · When the Mediamaster is connected to the TV set, you will now see a welcome message on the screen. You may now proceed to page 11 "Basic Settings". However, we recomend that you read the other information on the preceding pages first. Before you continue... please read this concerning menus A menu is a field of text shown on the TV screen. These menus contain different kinds of information and give the possibility to select between alternatives. In the bottom part of the screen you will normally also have a short explanation of your options. A menu may contain several lines. Selectable lines are highlighted. Non highlighted lines are not selectable. GB 8 Remote control This section describes how to operate the Mediamaster using the buttons on the remote control. You can also change programmes by pressing buttons on the Mediamaster`s front panel. To turn the Mediamaster on/off (standby). Press once to switch to audio language/audio track (if available). Press twice to switch to Radio mode. TV To leave a menu and go back to watch a TV programme. To switch from Radio Mode to TV Mode. To toggle between terrestrial TV, VCR, analogue and the digital satellite signal. To select channel number and other numerical commands. To obtain a list of present and coming programs for the available channels. This information is only shown if your Service Provider transmits programme information. To display the "Main menu" screen. To go back one level in the menus. To return to the Main Menu from a Submenu. To give short and extended information (if transmitted) about the current/next programme. LEFT/RIGHT To move in left/right direction within the menus. BUTTONS UP/DOWN BUTTONS DOUBLE ARROWS OK +To move in an up/down direction in the menus. To select TV and audio channels. To step pages or change channels up or down in the menus. (In blocks of 10). To confirm choices, etc. Select TV/Radio channel list. To increase or decrease the volume level of the Mediamaster. The Mediamaster's maximum level is controlled by the TV:s present volume setting. The volume adjustment also alters the volume level to your video recorder. To turn the sound on /off (mute). TEXT To select teletext information. Press once to change teletext subtitle. Press twice to enter teletext (if available). LEFT Double arrow UP RIGHT DOWN Double arrow 0-9 GUIDE MENU EXIT GB 9 About the Smart Card and CA Module. Model 9600 S only To be able to receive pay-TV channels you will need a CA Module and a Smart Card from the Service Provider of your choice. The Service Provider is the distributor of the programmes. If you are subscribing to services from more than one Service Provider, you might have to change between different Smart Cards, or even between different CA Modules. Please note, that a smart card is connected to a single Service Provider and due to this, a specific range of channels. Only "free" channels are available without the CA Module. After inserting the card, leave it in the slot permanently. Do not remove it again, unless your Service Provider asks you to do so. This is important, because if your Service Provider wants to download new i ...