Nokia Digital Pen (SU-27W) User Guide 9250690 Issue 1 EN DECLARATION OF CONFORMITY Hereby, NOKIA CORPORATION declares that this SU-27W product is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. A copy of the Declaration of Conformity can be found at http://www.nokia.com/phones/declaration_of_conformity/. © 2006 Nokia. All rights reserved. Reproduction, transfer, distribution or storage of part or all of the contents in this document in any form without the prior written permission of Nokia is prohibited. Nokia and Nokia Connecting People are registered trademarks of Nokia Corporation. Other product and company names mentioned herein may be trademarks or tradenames of their respective owners. Bluetooth is a registered trademark of Bluetooth SIG, Inc. Nokia operates a policy of continuous development. Nokia reserves the right to make changes and improvements to any of the products described in this document without prior notice. Under no circumstances shall Nokia be responsible for any loss of data or income or any special, incidental, consequential or indirect damages howsoever caused. The contents of this document are provided "as is". Except as required by applicable law, no warranties of any kind, either express or implied, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose, are made in relation to the accuracy, reliability or contents of this document. Nokia reserves the right to revise this document or withdraw it at any time without prior notice. The availability of particular products may vary by region. Please check with the Nokia dealer nearest to you. Unauthorized changes or modifications to this device may void the user's authority to operate the equipment. Export Controls This device may contain commodities, technology or software subject to export laws and regulations from the US and other countries. Diversion contrary to law is prohibited. 9250690 / Issue 1 EN 2 Contents 1. Introduction ......................... 4 Bluetooth wireless technology .......... 4 Reset the pen........................................ 11 3. Basic use ............................. 12 Notepads................................................ Ink color and line thickness.............. Create and manage notes................. Create and send messages................ Full memory .......................................... 12 12 13 13 14 2. Getting started..................... 5 Chargers ................................................... 5 Open and close the USB cradle ......... 6 Charge the battery ................................ 6 Charge from a PC............................... 6 Charge from a wall outlet ............... 7 Battery level indication .................... 8 Switch the pen on or off ..................... 8 Pair the pen............................................. 9 Pair from a mobile device................ 9 Pair from the pen ............................. 10 Change the ink cartridge................... 10 4. PC connectivity................... 15 Install Logitech io2 Software........... 15 Manage notes on a PC....................... 15 5. Battery information ........... 16 Care and maintenance ........... 17 3 Introduction 1. Introduction The Nokia Digital Pen allows you to write notes on compatible digital paper and transfer the notes to a compatible mobile device over a Bluetooth connection. You can also transfer the notes to a PC over a Bluetooth connection or by placing the pen in the USB cradle that is connected to the USB port of the PC. Read this user guide carefully before using the digital pen. Also read the user guide for your mobile device, which provides important safety and maintenance information, and the user guide for your PC. Keep the digital pen and its accessories out of reach of small children. Bluetooth wireless technology Bluetooth wireless technology makes it possible to connect compatible devices without cables. A Bluetooth connection does not require that the mobile device and the digital pen be in line of sight, but both devices should be within 10 meters (30 feet) of each other. Connections may be subject to interference from obstructions, such as walls, or other electronic devices. The digital pen is compliant with Bluetooth Specification 1.2 that supports the following profiles: Object Push Profile 1.2, Generic Object Exchange Profile 1.2, and Serial Port Profile 1.2. Check with the manufacturers of other devices to determine their compatibility with this device. There may be restrictions on using Bluetooth technology in some locations. Check with your local authorities or service provider. 4 Getting started 2. Getting started The digital pen contains the following parts: · Pen cap (1) · Ink cartridge (2) · Battery indicator (3) · Page indicator (4) · Ink cartridge removal hole (5) · Reset button (6) Before using the digital pen, you must charge its battery and pair the pen with a compatible mobile device. To use the pen with a compatible Nokia S60 or Series 80 mobile device, you must install the Nokia Digital Pen Suite software from the supplied CD-ROM to your mobile device. To use the pen with your PC or modify the pen settings, you must install the Logitech io2 Software from the CD-ROM to your PC. The software can be used with the Microsoft Windows XP or 2000 operating system. The CD-ROM also contains the Nokia Digital Pen SU-1B File Converter application that allows you to convert notes created with the Nokia Digital Pen SU-1B into the format supported by the Nokia Digital Pen SU-27W. The software may not be available in your language. 6 Chargers Check the model number of any charger before using it with this device. The digital pen is intended for use with the AC-3, AC-4, and DC-4 chargers. Warning: Use only chargers approved by Nokia for use with this particular enhancement. The use of any other types may invalidate any approval or warranty, and may be dangerous. 5 Getting started For availability of approved enhancements, please check with your dealer. When you disconnect the power cord of any enhancement, grasp and pull the plug, not the cord. Open and close the USB cradle The pen is supplied with a USB cradle that you need when you charge the battery inside the pen. To open the USB cradle, pull the top of the cradle away from its bottom. To close the cradle, push the button on the side of the cradle. When you do not use the cradle, you can wrap the USB cable around the indents on both sides of the cradle. Charge the battery The digital pen has an internal, nonremovable, rechargeable battery. Do not attempt to remove the battery from the pen as you may damage the pen. You can charge the pen from your PC using the supplied USB cradle or from a wall outlet using the supplied charger adapter and a compatible charger. Charging the battery fully takes up to 2 hours depending on the charger. If the battery is empty, it may take up to 10 minutes before the battery indicator starts to flash and the battery starts to charge. Charge from a PC To charge the pen battery from a PC, do the following: 1. Open the USB cradle, and place it on a flat surface. 6 Getting started 2. Switch on the PC, and plug the USB connector of the cradle to the USB port on the PC. 3. To start charging, remove the pen cap, and insert the pen into the USB cradle so that the connectors on the pen are facing the connectors on the cradle. If you use a laptop PC that is not plugged into a wall outlet, charging the pen battery from the PC increases the demand on the PC battery and reduces battery life. When you connect the cradle to your PC for the first time and the PC is running the Microsoft Windows XP or 2000 operating system, the pen is detected as new hardware and you are asked whether you want to install the digital pen drivers. If you want to only charge the pen battery and do not intend to transfer data from the pen to the PC, you do not need to install the pen drivers, and you can exit the dialog box. While the battery is charging, the battery indicator slowly flashes red, yellow, or green depending on the charge level of the battery. 4. When the battery is fully charged, the battery indicator turns solid green. Remove the pen from the cradle by lifting it, or unplug the USB connector from the PC. Charge from a wall outlet To charge the pen from a wall outlet, do the following: 1. Open the USB cradle, and place it on a flat surface. 2. Remove the pen cap, and insert the pen into the USB cradle so that the connectors on the pen are facing the connectors on the cradle. 7 Getting started 3. Plug the USB connector of the cradle to the AD-48 charger adapter that is supplied with the pen. 4. Plug the charger into a wall outlet, and connect the charger cable into the adapter. While the battery is charging, the battery indicator slowly flashes red, yellow, or green depending on the charge level of the battery. 5. When the battery is fully charged, the battery indicator turns green. Disconnect the charger cable from the adapter, unplug the charger from the wall outlet, disconnect the USB connector from the adapter, and remove the pen from the cradle. Battery level indication The battery indicator shows how much charge is left in the pen battery. When the battery indicator is green, the pen is sufficiently charged. When the battery indicator is yellow, the battery is less than 50% charged. When the battery indicator is red, battery power is low; when the indicator flashes red, battery power is too low for operation. Recharge the battery. You can also check the battery level using the charge meter in the Battery level indication section at the back of a supplied notepad. Move the pen tip from left to right. The pen indicates the current charge level by vibrating. Switch the pen on or off To switch on the pen, take off the pen cap. The pen vibrates once, and the battery and page indicators turn on. When the page indicator is green, the pen is ready to writing. The pen is automatically switched on when you insert it into the USB cradle that is connected to a powered USB port or to the AD-48 charger adapter. 8 Getting started To switch off the pen, replace the pen cap. The battery and page indicators turn off. The pen is automatically switched off when you detach the USB cradle from the PC while the pen is placed in the cradle. To save power and protect the lens inside the pen from dirt, always keep the cap on when you are not using the pen. Pair the pen You must pair the pen with a compatible mobile device to transfer data from the pen. The pen can be paired with one mobile device at a time. To use the pen with another mobile device, you must pair the pen with it first. The Bluetooth passcode that you need for pairing is printed on the card that comes in the sales package. You can change this preset passcode with the Logitech io2 Software that can be found on the supplied CD-ROM. Pair from a mobile device 1. Take the cap off the pen or remove the pen from the USB cradle, and ensure that the pen and your compatible mobile device are switched on. The page indicator slowly flashes blue to show that the pen can be paired with a compatible device within 2 minutes. You can prevent other Bluetooth devices from discovering your digital pen with the Logitech io2 Software that is supplied on the CD-ROM in the sales package. For details, see the Logitech io2 Software documentation. 2. Activate the Bluetooth feature on your mobile device, and set the mobile device to search for Bluetooth devices. See the user guide of your mobile device for instructions. 3. Select the digital pen from the list of found devices. 4. Enter the Bluetooth passcode on the mobile device. 9 Getting started In some mobile devices you may need to make the Bluetooth connection separately after pairing. You only need to pair the digital pen with your mobile device once. If the pairing is successful, the pen vibrates three times, and the page indicator turns green and is shown for 2 seconds. The pen is now ready for use. If the pairing or connection fails, the page indicator briefly flashes red twice and is shown for 2 seconds. Check that the pen and the mobile device are switched on, and carefully enter the correct Bluetooth passcode. You can set the pen to connect with your mobile device automatically when the pen is switched on. To do this in Nokia devices, change your paired device settings in the Bluetooth menu. The Bluetooth connection between the digital pen and the compatible mobile device is active only when the pen sends notes to the mobile device. Pair from the pen 1. Activate the Bluetooth feature on your mobile device as instructed in its user guide. 2. Use the pen to tap the Pairing box box that can be found at the end of the notepad. The page indicator flashes blue to show that the pen can be paired with a compatible device with ...