Remote Control Buttons Button Function Power ON ­ Press and release. Power OFF ­ Press & Hold for 2 seconds. CHECKS dispenser ­ Places dispenser's formula on remote's screen, checks dispenser's battery, displays if in BAT LOW state. SENDS displayed formula to a dispenser. TO SEND a saved formula ­ Press a PROG button, then press SEND.* HOME SCREEN shows day & time. Start from the Home Screen when sending a formula or checking a dispenser. TO SET day & time, press CLOCK to underscore day. REVIEW displays programmed events in a formula. Each press of REVIEW moves to the next event in that formula. (1) TO REVIEW A SAVED FORMULA ­ Press PROG button, then press REVIEW. (2) TO REVIEW DISPENSER'S FORMULA­Press CHECK, then press REVIEW. PROG buttons store formulas in remote's memory. * PROG 1 ­ Holds factory pre-set formula (on a new remote). TO SAVE A FORMULA ­ With formula displayed, press and hold a PROG button for 2 seconds (overwrites previous formula). SAVES programming changes. NOTE: Press after each event is changed. To save a Formula or Day/Time, continue pressing until DONE ( or the Home Screen) displays. RIGHT ARROW UNDERSCORES the event displayed to make it "editable." LEFT/RIGHT ARROWS move the underscore to the right or left. UP/DOWN ARROWS SCROLL through available choices for programming the day, time or dosage. N O VA C O N T R O L S LEADING THE WAY Quick Start Guide to Remote Programming First-Time New Remote Set Up - Ersteinstellung Neue Fernbedienung - Nouvelle Installation à Distance pour la Première Fois -Instalación a Distancia por Primera Vez -Installi per la prima volta il nuovo telecomando - Instalação à Distancia pela Primeira Vez 1. Install Battery - Bringen Sie die Batterie an - Installez la batterie - Instale la batería - Installi la batteria - Instale a bateria 2. Choose ml. or oz. - Wählen Sie ml oder Unze - Choisissez le ml ou l'once - Elija en ml o en onzas - Scelga il ml o l'oncia - Escolha em ml. ou em onç Power OFF (Default) Home Screen (oz.) A Systems Company REMOTE PROGRAMMER User's Guide OZ. = or Home Screen (ml.) ML = 3. Set Day & Time + ml. - Hauptmenü - Écran À la Maison - Pantalla Inicial - Schermo Domestico - Tela Inicial - Regoli il giorno e l'ora - Ajuste o dia e a hora - Stellen Sie Tag und Zeit ein - Sélectionnez le jours et l'heure' - Fije el día y la hora This Pro-Flow Remote Programmer User's Guide explains how to set-up and use the hand-held Remote Programmer to check, revise, save, and send formulas to a Pro-Flow dispenser. Additional information about the system can be found in the Pro-Flow Drain Cleaning Reference Manual, p/n 20-08363-00. Note Store the Remote Programmer in a cool, dry place. Do not leave it in direct sunlight or near high heat. For technical assistance or product ordering, contact your authorized product representative 20-08171-00 Rev D Clock Home Screen DAY SUN MON TUE WED THU FRI SAT - TAG - JOUR - Sonntag - Dimanche - Montag - Lundi - Dienstag - Mardi - Mittwoch - Mercredi - Donnerstag - Jeudi - Freitag - Vendredi - Samstag - Samedi - DÍA - GIORNO - Domingo - Domenica - Lunes - Lunedì - Martes - Martedì - Miércoles - Mercoledì - Jueves - Giovedì - Viernes - Venerdì - Sábado - Sabato - DIA - Domingo - Segunda - Terça - Quarta - Quinta - Sexta - Sábado Current Day & Time Copyright 2005 Nova Controls, Inc. PROGRAMMING - Programmierung - Programmation - Programación - Programmazione - Programação SEND Pre-Set Formula = 10 OZ (300 ML), 00:00 HRS, SUN - SAT - Voreingestellte Formel Senden - Envoyez La Formule Préréglée - Envíe la Fórmula Preestablecida - Trasmetta La Formula Prestabilita - Evie a Fórmula Pré-ajustada Power ON Home Screen Power OFF Hold 2 Sec. 11 10 12 1 2 3 4 7 6 5 1. Overview Turn On: Press the POWER button . The Home Screen (current day and time) displays. (If the battery is low, BAT LOW displays first, then the Home Screen.) for 2 seconds. Turn Off: Press and hold the POWER button Remote turns off automatically after 2 minutes of inactivity. 1.1 Basic Operation Each product dose is called an event (event = day + time + dosage). The pre-set formula has seven events (Sunday Saturday). If desired, the installer can edit events in the pre-set formula to create new formulas. Up to three formulas (including the factory pre-set) can be saved in the remote. Before using a new remote, you must set the units of measurement (oz or ml) and the clock (day & time). Clock settings load into a dispenser automatically whenever you SEND a formula or CHECK the status of a formula. A back-up lithium battery saves programs and clock settings when the remote is off or the battery is replaced. The Remote Programmer ("the remote") stores formulas/ programs for the installer to SEND to a dispenser. The remote also CHECKS and displays information about the dispenser's formula and battery life. Just one remote is needed to program multiple Pro-Flow dispensers. Note FACTORY PRE-SET FORMULA Each remote is shipped with a factory pre-set formula that is saved as PROG 1. That pre-set formula is: 10 oz (300 ml), dispensed at midnight, 7 days a week. 2. Set Up a New Remote Programmer After setting the CLOCK, stand within 4 ft. (1.2 m) of dispenser, point remote at dispenser, and press SEND. Hold remote in place until SET displays. If COM BAD displays, see Troubleshooting. Go to sections "7. Prime the Pump." and "8. Test the Dispenser." 2.1 Send Factory Pre-Set Formula to Dispenser = 9 8 REVIEW / CHANGE a Formula - Formel Ansehen/Verändern - Passez en revue/Changez une formule - Revise/Cambie una fórmula - Riveda/Cambi una formula - Reveja/Mude uma fórmula Home Screen HRS 1. Insert 9-volt battery (included). Secure the battery cover. 2. Set unit of measurement during remote power-on. In a new remote, OZ. is the default. If ML is preferred, skip to Step b BEFORE turning on the remote: (a) To accept OZ , press POWER button to turn on remote. (b) To select ML , press and HOLD ENTER button , while also pressing POWER button .This turns the remote on and sets it to metric. ML flashes, followed by a day & time. 3. Set the 24-hour clock with local day and time in military format, 00:00 - 23:59. (a) With remote on, press CLOCK button. CLOCK set displays, with day underscored. (b) Press UP/DOWN arrows until the current day displays. (c) Press RIGHT arrow. Move underscore to first number in TIME. (d) Press UP or DOWN arrows until correct number displays. Repeat for all four numbers. Leave a zero in the left-hand column where appropriate (i.e. 08:25). (e) When current day and time display (i.e. WED 18:30), press the ENTER button to save and exit.To exit without saving changes, press CLOCK again to display the CLOCK day and time (also called the Home Screen). HRS ( )( ) ml. oz. , ... - Mude uma fórmula HRS CHANGE a Formula - Formel Verändern - Changez une formule HRS HRS - Cambie una fórmula HRS - Cambi una formula 2 Sec. ml. oz. ml. oz. ml. oz. ml. oz. DELETE an Event - Einen Fall löschen -Supprimer un événement -Suprimir un acontecimiento -Cancellare un evento -Suprimir um evento Home Screen HRS HRS HRS 2 Sec. x 8888888:88DAYS . 888 ml.oz. HRS x ml. oz. ml. oz. ml. oz. CHECK Dispenser - Überprüfen des Dispensers - Vérifiez Le Distributeur - Compruebe El Dispensador - Controlli L'Erogatore - Verifique O Distribuidor HRS DAYS m) (1.2 4 ft. f sight o line Hidden Prime Buttons ml. oz. PRIME Pump - Produkt Ausaugen - Amorcez la pompe - Prepare la bomba - Inneschi la pompa - Apronte a bomba 3. Send a Formula to a Dispenser 1. Making sure that the remote is powered on, has a clear lineof-sight, is within 4 ft. (1.2 m) of the dispenser, AND displays the HOME screen, point the remote directly at the dispenser and either: (a) Press SEND to send the last program displayed on the screen, or (b) Press any PROG button that has a saved formula, then press SEND. A new remote contains the factory pre-set formula as the PROG 1 button. 2. SET displays to indicate that programming is successful. 3. If COM BAD displays, see Section 4. Troubleshooting. 6. Customized Programming Create custom formulas by reviewing a formula, adding or deleting events in the formula, then saving the revised formula to a PROG button. To add or delete events, you must first make the displayed formula "editable" by pressing the RIGHT ARROW and underscoring the DAY, TIME or DOSAGE. PROG 1 holds the factory pre-set formula. To avoid overwriting the factory pre-set, save additional custom formulas to the PROG 2 and PROG 3 buttons. A formula can be temporarily modified and sent to a dispenser without being saved. The temporary formula remains in the remote until another formula is used or the remote is powered off. NOTE · You can only edit or delete the event that you are currently viewing on the remote's screen. · Because each event is unique, each must be separately edited or deleted. Programming Navigation Buttons UP ARROW Increases / Moves Value Forward ENTER / SAVE LEFT ARROW Moves underscore back RIGHT ARROW Underscores next item 6.2.3 Review, Save and Exit Options DOWN ARROW Decreases / Moves Value Backward 6.2 Create Custom Formulas 4. Troubleshooting 4.1 COM BAD displays instead of SET The formula was NOT successfully downloaded. The most likely reasons are: · The remote is too far from the dispenser. · The remote is not pointed directly at the dispenser, but is angled more than 7° to the right or left of the dispenser. · There is an obstruction between the remote and the dispenser. · The dispenser is in bright light or sunlight. · The remote did not display the Home Screen before SEND was pressed. 4.2 Remote's factory pre-set formula is accidentally lost Quick recovery is possible by aiming the remote at a brand new dispenser (that is powered on) and pressing CHECK. This should upload the pre-set formula to the remote's display. Press and hold PROG 1 for 2 seconds to save the displayed formula. To add or delete events and customize your formulas, you must first place the formula in the remote's display by pressing the REVIEW button. (See Section "6.1 Review a Formula." ). Add an event by revising an existing event, or delete an existing event by setting the dosage to zero (- - - ), as explained below. IMPORTANT! Creating a new event (by changing the Day, Time or Dosage of an existing event) does NOT delete the old event--it ADDS another event to the formula. If the old event is no longer needed, it MUST be manually deleted from the formula. CAUTION When Saving Formulas! · You must save a new formula to a PROG button or it will be lost when the next formula is displayed. · If you accidentally press CHECK and are within communication distance and angle to a dispenser, the dispenser's program will upload to the remote and replace the previously displayed formula. · Saving a new formula to a PROG button deletes the previously saved formula (even the factory pre-set formula). Before saving, verify that the PROG location is empty or that you no longer need the old formula. There is no "undo" if a formula is lost. Choose one or more of the following actions to complete your customized programming: (a) Add or delete another event in the same formula ­ Press REVIEW and follow the steps in the previous sections to add or delete another event. (b) Review your changes ­ Press REVIEW to see each new, saved event within the formula. Verify that events you just added appear correctly and that you no longer see events that you deleted. Make corrections as needed. DONE displays when all events in the formula have been reviewed. (c) Send the formula without saving it ­ With DOSAGE underscored, press CLOCK to return to the Home Screen, then press SEND (See also Section"3. Send a Formula to a Dispenser.") (d) Save the new formula to a Program button ­ Press and hold a PROG button for two seconds. OK displays to let you know that the formula was successfully saved. (e) Exit to the Home Screen ­ Press CLOCK. Your new formula is ready to send. Note Pressing the CLOCK button exits an "editable" event only when the DOSAGE is underscored or OK displays after saving a formula to a PROG button. 6.2.1 Add a New Event Programming Options Choose from 7 days, 8 times, & 12 dosage amounts (metric or SAE): DAY: TIME: SUN, MON, TUE, WED, THR, FRI, SAT 00:00, 03:00, 06:00, 09:00, 12:00, 15:00, 18:00, 21:00 5. On-Going Service / Checking Dispenser Status During service calls, press CHECK to retrieve information from a dispenser and display it on the remote. If communication is successful, the following sequence displays on the remote: 1. NEW MON 09:00 8 OZ (or whichever is the first event in the current program). Press REVIEW to see all events in that formula. To change the dispenser's formula, you can either: · Create or delete an event(s) and send the new formula or · Replace the dispenser's formula with saved formula from the remote. 2. ...