ALLURE® WS3 SERIES RANGE HOOD ® Page 1 ALLURE® WS3 SERIES RANGE HOOD READ AND SAVE THESE INSTRUCTIONS Patent No.: US D450, 829 S ! WARNING FOR DOMESTIC COOKING ONLY CAUTION ! ! TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: 1. Use this unit only in the manner intended by the manufacturer. If you have questions, contact the manufacturer at the address or telephone number listed in the warranty. 2. Before servicing or cleaning unit, switch power off at service panel and lock the service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel. 3. Installation work and electrical wiring must be done by a qualified person(s) in accordance with all applicable codes and standards, including fire-rated construction codes and standards. 4. Sufficient air is needed for proper combustion and exhausting of gases through the flue (chimney) of fuel burning equipment to prevent backdrafting. Follow the heating equipment manufacturer's guideline and safety standards such as those published by the National Fire Protection Association (NFPA), and the American Society of Heating, Refrigeration and Air Conditioning Engineers (ASHRAE), and the local code authorities. 5. When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities. 6. To reduce the risk of fire or electric shock, do not use this range hood with an additional speed control device. 7. Ducted fans must always be vented to the outdoors. 8. To reduce the risk of fire, use only metal ductwork. 9. Use with approved cord-connection kit only. 10. This unit must be grounded. TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE: 1. Never leave surface units unattended at high settings. Boilovers cause smoking and greasy spillovers that may ignite. Heat oils slowly on low or medium settings. 2. Always turn hood ON when cooking at high heat or when cooking flaming foods. 3. Clean ventilating fans frequently. Grease should not be allowed to accumulate on fan or filter. 4. Use proper pan size. Always use cookware appropriate for the size of the surface element. TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A RANGE TOP GREASE FIRE, OBSERVE THE FOLLOWING:* 1. SMOTHER FLAMES with a close-fitting lid, cookie sheet, or metal tray, then turn off the burner. BE CAREFUL TO PREVENT BURNS. If the flames do not go out immediately, EVACUATE AND CALL THE FIRE DEPARTMENT. 2. NEVER PICK UP A FLAMING PAN -- You may be burned. 3. DO NOT USE WATER, including wet dishcloths or towels - violent steam explosion will result. 4. Use an extinguisher ONLY if: A. You know you have a Class ABC extinguisher and you already know how to operate it. B. The fire is small and contained in the area where it started. C. The fire department is being called. D. You can fight the fire with your back to an exit. * Based on "Kitchen Fire Safety Tips" published by NFPA. 1. For general ventilating use only. Do not use to exhaust hazardous or explosive materials and vapors. 2. To avoid motor bearing damage and noisy and/or unbalanced impellers, keep drywall spray, construction dust, etc. off power unit. 3. For best capture of cooking impurities, your range hood should be mounted so that the top of the hood is 24-30" above the cooking surface. 4. Please read specification label on product for further information and requirements. Installer: Leave this manual with the homeowner. Homeowner: Operating and Cleaning information on page 6. NOTE If hood is to be installed Non-Ducted: · Purchase a set of (2) non-ducted filters from your local distributor or retailer and attach them to the aluminum mesh filters. TABLE OF CONTENTS This manual is divided into sections as follows: · "PREPARE HOOD LOCATION" Run ductwork from roof or wall cap, and electrical wiring from service panel - to installation location "PREPARE THE HOOD" Get your hood ready for installation "CONNECT WIRING" Make electrical wiring connections to hood "INSTALL HOOD" Secure hood to cabinet and ductwork - install bulbs and filters "OPERATION" How to use the hood controls "CLEANING" Keep your hood in top working condition "SERVICE PARTS" Part numbers and exploded view of hood components "WARRANTY" One-year limited warranty and how to contact us · · · · · · · ALLURE® WS3 SERIES RANGE HOOD ® Page 2 PREPARE HOOD LOCATION ROOF CAP 3¼" X 10" or 7" ROUND DUCT (For vertical discharge) PREPARE HOOD LOCATION 7" ROUND VERTICAL DUCTING SOFFIT CABINET HOUSE WIRING (Top or Back of hood) WALL CAP HOOD 24" - 30" ABOVE COOKING SURFACE 3¼" X 10" DUCT (For horizontal discharge) 1 2 Determine whether hood will discharge vertically (3¼" x 10" or 7" Round), or horizontally (3¼" x 10" only). For vertical or horizontal discharge, run ductwork between the hood location and a roof cap or wall cap. For best results, use a minimum number of transitons and elbows. Use diagrams, below, for proper placement of ductwork and electrical cutout in cabinet or wall. For a non-ducted installation, DO NOT cut a duct access hole. HOOD MOUNTING SCREWS (4) 1315/16" (30" hood) 1315/16" (30" hood) 1615/16" (36" hood) 1615/16" (36" hood) 1915/16" (42" hood) 1915/16" (42" hood) CABINET FRONT 7½" CABINET BOTTOM 5¼" 5¼" 5" 1¼" WOOD SHIMS (recessed-bottom cabinets only) WOOD SHIMS (recessed-bottom cabinets only) CENTER LINE ELECTRICAL ACCESS HOLE (in cabinet bottom) VERTICAL DUCT ACCESS HOLE 3 Run house wiring between service panel and hood location. PREPARE THE HOOD 7" ROUND DUCT PLATE 3¼" X 10" VERTICAL DUCTING 2" 10½" 1½" 1 Remove 7" Round Duct Plate from top of hood. Set duct plate aside - with mounting screws. 3¼" X 10" HORIZONTAL DUCTING CABINET FRONT 1/8" FILTERS ¾" 3¾" HORIZONTAL DUCT ACCESS HOLE CABINET 5¼" 5¼" BOTTOM 7½" 1315/16" (30" hood) 1315/16" (30" hood) 1615/16" (36" hood) 1615/16" (36" hood) 1915/16" (42" hood) 1915/16" (42" hood) HOOD ELECTRICAL MOUNTING CENTER ACCESS HOLE SCREWS (4) LINE (in wall) 2 Remove tape holding Filters in place. Pull down on filter tabs or finger holes and lift filters out. Set filters aside. ALLURE® WS3 SERIES RANGE HOOD ® Page 3 PREPARE THE HOOD 3 Remove Teflon®-coated bottom cover from hood. Set cover and mounting screws aside. PREPARE THE HOOD AIR CHUTE 7 Remove Air Chute - held in place with one (1) screw. NOTE: Be careful not to disconnect any wires. Teflon® is a registered trademark of DuPont. TEFLON -COATED BOTTOM COVER (Held in place with 2 screws) 4 Remove Damper/Duct Connector from inside the hood. Set connector aside - with mounting screws and parts bag. DAMPER/ DUCT CONNECTOR 5 Remove either top or back wiring knockout and install approved Electrical Cable Clamp. ® 8 Remove Baffle from air chute. BAFFLE BAFFLE ELECTRICAL CABLE CLAMP Non-Ducted Installation - Skip to Step 15. (3) #8 SCREWS LIGHT PANEL 9 6 Remove Light Panel - held in place with (3) #8 screws and (2) #8 screws. Disconnect light assembly wire harness (white connector). 10 Re-install air chute, re-connect wire harness, and replace light panel. NOTE: Be careful not to trap wires between support fin and light panel. SUPPORT FIN The following Steps (6 thru 14) are for DUCTED INSTALLATION ONLY. (2) #8 SCREWS Rotate baffle. Reinsert baffle into air chute (as shown) so that baffle tabs fit all the way into slots in air chute. An audible "click" will be heard when fully installed. This will close off the air flow through the non-ducted slots on top of hood. SLOTS TABS ALLURE® WS3 SERIES RANGE HOOD ® Page 4 PREPARE THE HOOD TOP RECTANGULAR DUCT KNOCKOUT (Remove for 3¼" x 10" Vertical & for 7" Round Discharge) SEMI-CIRCULAR DUCT KNOCKOUT (Remove for 7" Round Discharge) PREPARE THE HOOD TAPE UP TO 1" SIDE-TO-SIDE ADJUSTMENT TOP/BACK EDGE DAMPER/ DUCT CONNECTOR (Vertical discharge position shown) PIVOT REAR RECTANGULAR DUCT KNOCKOUT (Remove for 3¼" x 10" Horizontal Discharge) 11 Remove appropriate Duct Knockout(s) from top or back of hood. 13 3¼" x 10" Ducted Discharge Only: Remove Tape from damper flap and attach Damper/Duct Connector over knockout opening with screws removed in Step 4 under "PREPARE THE HOOD". Make sure damper Pivot is nearest to Top/Back Edge of hood. 7" Round Ducted Discharge Only: Re-install 7" Round Duct Plate removed in Step #1 under "PREPARE THE HOOD". Install a 7" round damper (purchase separately). Damper flap must open freely in direction of airflow (away from range hood). 14 SCREW TIES To accomodate off-center ductwork, the Damper/Duct Connector can be installed up to 1-inch on either side of hood center or the 7" Round Duct Plate can be installed up to ½" on either side of hood center. In extreme off-center installations, one end of the duct connector may need to be trimmed to clear the electrical cable clamp. NOTE BLOWER WHEEL TAB SMALL DIAMETER END RETAINING RING SECTIONS MOTOR STOP SLOTS EDGE 15 METAL STRIP 12 PLATE Non-Ducted Installations Only: Require a Performance Ring to be attached to the blower wheel. To install ring: 1. Remove the Blower Wheel by rocking it side to side and applying a slight force to pull wheel from motor. Remove Retaining Ring if necessary. 2. Slide the ring onto the Small Diameter End of the wheel and down to the Stop Edge of the wheel. 3. Reassemble wheel to motor. Make sure Tab on wheel fits into one of the Motor Slots. 4. Push wheel down until it is locked in place. 5. Check that wheel is properly positioned as shown. Press Sections into place if necessary. Make sure wheel turns freely. Horizontal Discharge Only: Remove the Plate in front of the horizontal discharge knockout. Cut the Ties, lift plate out, and discard plate. DO NOT REMOVE the Metal Strip held in place with two Screws. RING ALLURE® WS3 SERIES RANGE HOOD ® Page 5 CONNECT WIRING WARNING: To reduce the risk of electric shock, make sure power is switched off at the service panel. Lock or tag service panel to prevent power from being switched on accidentally. INSTALL HOOD HOUSE WIRING (120 VAC) KEYHOLE (4) 1 CARDBOARD (Use to protect cooktop) 2 1 Connect House Wiring (120 VAC) to hood. Use a piece of Cardboard to protect the cooktop, if necessary. MOUNTING SCREW (4) Hang hood from (4) Mounting Screws. Slide hood towards wall until mounting screws are engaged in narrow end of (4) Keyholes. Tighten mounting screws securely. A long screwdriver works best. Replace bottom cover. DUCT TAPE 3 GREEN GROUND SCREW Connect ductwork to hood. Use Duct Tape to make joints secure and air tight. 2 Connect house black to hood black wire, house white to hood white wire, and house ground under Green Ground Screw. Securely tighten cable clamp onto house wiring. PAR20, 50W MAX. HALOGEN BULB (2) - or R16, 40W MAX. INCANDESCENT BULB (2) 4 Install (2) PAR20, 50 W Maximum Halogen Bulbs or (2) R16, 40 W Maximum Incandescent Bulbs. Purchase bulbs separately. ! 5 CAUTION: Bulbs may be hot! Refer to bulb packaging for further information. Replace filters, turn on power at service panel, and test for proper operation. ALLURE® WS3 SERIES RANGE HOOD ® Page 6 NON-DUCTED FILTERS If hood is to be installed Non-Ducted: Purchase a set of (2) Non-Ducted Filters from your local distributor or retailer and attach them to the aluminum mesh filters. NOTE: For models that are installed in the non-ducted mode, the most effective operation is achieved at speeds 1 and 2. These speeds provide the most efficient and quiet operation during cooking, while maximizing the benefits of the recirculating filtration system. 3. Remove and inspect fuse. If it is not open (blown), additional diagnostics need to be done. 4. Install new fuse. 5. Re-assemble air chute, light wire harness, bottom panel, and filters. 6. Turn on power and check hood/control operation. CLEANING WARNING: To reduce the risk of electric shock, disconnect from power supply before cleaning. Aluminum mesh filters: Clean frequently using hot water and a mild detergent. Filters are dishwasher safe. Charcoal filters: Clean filter surfaces frequently with a damp cloth and a mild detergent. DO NOT immerse filters in water or put in dishwasher. The special "Clean Sense" feature indicates when the filter is to be replaced. The blue and yellow strips will blend to green when it is time to change the filter. The "Clean Sense" feature works best when facing toward the cooking surface. To clean hood: Remove filters. Use a damp cloth and a mild detergent to wipe all grease-laden surfaces. Do not use abrasive cloth, steel wool pads, or scouring powder on the Teflon®-coated bottom cover or on any painted surface. Use care when cleaning blower wheel - it must not become bent or misaligned. DO NOT ALLOW WATER TO ENTER MOTOR. Make sure all surfaces are completely dry before re-installing filters and restoring power. Motor is permanently lubri ...