Flash Power Grip FP-1 Instructions Thank you for purchasing the OLYMPUS Flash Power Grip (FP-1). The FP-1 is the flash power grip for exclusive use with OLYMPUS digital cameras. Before use, please read this instruction manual to ensure your safety, and keep it handy for future reference. WARNING Do not use the flash power grip, connection cord or battery if it is damaged. To avoid electric shock or injury, do not touch any exposed internal parts. If the product is damaged, unplug the power cord and do not use it. For repair, contact Olympus. To avoid fire, overheating, explosion or leakage, do not subject the battery to excessive shock, throw it, or otherwise damage it. SAFETY PRECAUTIONS (Be sure to read and observe the following.) DANGER Failure to observe the precautions indicated by this symbol may result in serious injury or death. WARNING Failure to observe the precautions indicated by this symbol may result in injury or death. CAUTION Failure to observe the precautions indicated by this symbol may result in injury or property damage. Never put the battery in a microwave oven or high-pressure container. This could cause a fire, leakage, overheating, or an explosion. Do not leave the flash power grip within reach of children. · If a child swallows a battery or small accessory, see a doctor immediately. · If the flash is emitted near a child, their eyes may be injured irreparably. · Moving parts of the electronic flash could injure a child. · · · · · Avoid the following actions to prevent fire or injury due to battery fluid leak, overheating, fire ignition or bursting. Do not use batteries that are not specified for use with this flash power grip. Do not throw a battery into a fire, expose it to heat, short circuit it, or disassemble it. Do not mix old and new batteries, or batteries of different types or brands. Do not attempt to recharge non-rechargeable batteries such as alkaline batteries. Do not load batteries with the +/­ polarity reversed. Do not store the flash power grip anywhere where it could be exposed to excessive dust or moisture. Otherwise, fire or electric shock may result. Symbols for prohibiting action Prohibited Disassembly prohibited Symbol instructing action Mandatory For customers in Europe The "CE" mark indicates that this product complies with the European requirements for safety, health, environment and customer protection. CE-mark products are for sale in Europe. For customers in USA FCC Notice This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any unauthorized changes or modifications to this equipment would void the user's authority to operate. CAUTION Do not place a heavy object on this product or power cord. Do not place this product on an unstable surface such as a tilted or unsteady table. If it falls off, damage or injury may result. Do not store or use the flash power grip where it may be exposed to moisture, excessive dust or high temperatures. The batteries become very hot after extended use. Do not remove batteries immediately after use, as this may result in burns. Remove the batteries when the flash power grip is not going to be used for a long period. Improper use of batteries may result in fluid leak, heat generation and/or damage. Sweat and oil smudges may cause battery contact failure. To prevent this, remove any stain completely with a dry cloth and insert the batteries by observing the +/­ polarity If battery fluid gets on your skin or clothes, it may cause injury. Wash it off immediately with clean water and see a doctor. If the battery fluid comes in contact with your eyes, blindness may result. Rinse your eyes with clean water without rubbing them and see a doctor immediately. Do not apply a strong shock to a battery or throw it. When traveling overseas, it is a good idea to carry spare batteries with you. In some countries, it may be difficult to obtain certain batteries. Do not immerse batteries in water or expose to moisture including rain, seawater and animal urine. If the +/­ terminals of a battery are stained with sweat or oil smudges, contact failure may result. Clean the terminals well with a dry cloth before using the batteries Do not throw a battery in fire or heat it. When disposing of batteries, be sure to follow local regulations. For customers in CANADA This Class B digital apparatus complies with Canadian ICES-003. DANGER Use only the designated accessories. · The flash power grip has been designed exclusively for use with the FL-50 electronic flash for Olympus digital cameras. Do not use it with any other type of flash. · Always use the designated bracket cable and remote grip cable. · The flash power grip should be powered with C (R14) alkaline batteries only. Do not use any other type of power supply. Do not use the flash power grip for any purpose other than flash shooting. Never expose this product to water or moisture including rain, seawater and animal urine. Do not handle the flash power grip when it is wet or when your hands are wet, and do not use it in a damp environment (such as in a bathroom). Do not insert a metallic object (such as a wire) inside the flash power grip or into a contact. Do not attach solder to the flash power grip or attempt to repair, deform, modify or disassemble it. Do not use a battery that is damaged, leaking, or wet. Do not use or store the flash power grip in a place that may be exposed to high temperatures (for example, on a car dashboard under direct sunlight or near heating equipment). Do not use the flash power grip in a place where heat may accumulate (for example, under a cushion). Do not use the flash power grip where it may be exposed to flammable gas. Doing so poses a risk of fire or explosion. Never throw the battery into a fire or put it near a fire. When unplugging a cable, pull it out by grasping the plug, not the cord. Damage to the cord may result in fire ignition, explosion, damage, battery fluid leak and/or electric shock. Do not use the flash power grip near heat-generating equipment. This could damage the external finish or melt the coating and result in fire, overheating, explosion, fluid leak or electric shock. Note on cameras used with the Flash Power Grip For details, please refer to Olympus website (http://www.olympus.com/) or contact Olympus. CONTENTS · Checking the Package Contents ................................................................................................. 16 · Preparing the Optional Accessories ............................................................................................. 17 · Nomenclature .............................................................................................................................. 18 · Loading Batteries ......................................................................................................................... 19 · Assembly ..................................................................................................................................... 20 · Turning Power On ........................................................................................................................ 22 · Releasing the Shutter .................................................................................................................. 22 · Using the Remote Cable RM-CB1 (Optional) .............................................................................. 22 · Various Operations ...................................................................................................................... 23 · Flash Interval and Flash Count .................................................................................................... 24 · Main Specifications ...................................................................................................................... 24 Optional Accessories Depending on the camera you are using, you will need some of the following optional accessories. Electronic Flash FL-50 Other flashes cannot be used. Bracket Cable · When the camera has a hot shoe: Bracket Cable FL-CB02 · When the camera has a 5-pin external flash connection terminal: Bracket Cable FL-CB01 Remote Grip Cable RG-1 Checking the Package Contents Check that all parts and accessories are present. If any item is missing or damaged, contact your dealer. When the camera has a remote control terminal, the shutter can be released with the shutter button of the flash power grip. · Possible only when used with the bracket cable. Grip Strap GS-2 How to attach the grip strap GS-2 (optional) · Grip · The batteries must be purchased separately. · Bracket Nomenclature Grip Connection terminals Loading Batteries Use four C (R14) alkaline batteries. C (R14) NiCd batteries can also be used. · C (R14) manganese batteries cannot be used. How to load batteries Hot shoe Shutter button External power connector Rotary lock lever Power switch Strap hooks · Attach the grip strap GS-2 (optional). Battery compartment cover 1. Lift the battery compartment cover lock and turn it toward to open the cover. 2. Insert batteries, making sure they are oriented correctly. Bracket cable terminal 3. Slide the battery compartment cover until it locks Bracket mounting rail into place. Battery compartment cover lock Bracket External power connector protection cap storage position Notes Grip mount screw · Do not mix old and new batteries or batteries of different types together. · Remove the batteries when the electronic flash is not going to be used for a long period. · Carry spare batteries when traveling or when using the flash power grip in cold areas. Remote grip cable terminals (x 2) Terminal cap attaching section Grip mount screw Camera mount screw Grip mount section Tripod hole Assembly 1. Attach the grip and bracket. 1. Loosen the grip mount screw on the bracket. 2. Fit the bracket into the bracket mounting rail and slide the bracket down. 4. Connect the bracket cable (optional). Also read the bracket cable (optional) instruction manual. If the camera has a hot shoe: Connect the bracket cable FL-CB02 (optional) between the flash power grip's bracket cable terminal and the camera's hot shoe. 3. Position the bracket as desired, then tighten the Grip mount screw. · Clamp the bracket firmly so that it does not rattle. 2. Attach the electronic flash FL-50 (optional). To avoid a malfunction, be sure to turn the FL-50 and flash power grip off beforehand. If the camera does not have a hot shoe: Connect the bracket cable FL-CB01 (optional) between the flash power grip's bracket cable terminal and the camera's 5-pin external flash connection terminal. 1. Remove the protective cap from the FL-50's external power connector. · Store the removed protective cap in the storage position as shown in the figure on the left. 2. Slide the FL-50 into the flash power grip's hot shoe. Make sure the FL-50 is connected firmly to the connection terminals. 5. Attach the remote grip cable RG-1 (optional). Rear view 3. Turn the lock ring of the FL-50 all the way to 1. Remove the caps from the remote grip cable terminals on the flash power grip and camera. · To avoid losing the removed cap, attach it to the terminal cap attaching position. · The flash power grip has two remote grip cable terminals. Select whichever is most convenient. [ LOCK]. 3. Attach the camera. 1. Attach the camera by inserting the camera mount screw into the tripod hole of the camera. · The camera can be attached to one of the four holes. · The Power Battery Holder HLD-2 can also be attached. Terminal cap attaching position 2. When connecting the remote grip cable to the bracket on the flash power grip, align the indented section of the cable plug with the projecting part of the terminal, insert the plug and turn the knob clockwise to tighten. Turning Power ON 1. Turn the flash power grip on. 2. Turn the FL-50 electronic flash on. Memo: Always turn the flash power grip on before the electronic flash. As the flash power grip supplies the control power to the FL-50 electronic flash, it is not necessary to load batteries in the FL-50 electronic flash. In this case, however, the flash charge time increases slightly and the available flash emission count decreases. Various Operations 1. Combined use with the High Voltage Pack HV-1 1. Remove the protective cap from the flash power grip's external power connector. · To avoid losing the removed cap, insert it into the protective cap attaching position of the HV-1. 2. Connect the cable from the HV-1 to the external power connector. 3. Turn on the equipment in the following order: HV-1, flash power grip and FL-50. · For details, refer to the Flash High Voltage Set ...