In TV, VCR, DVD, SAT, and CBL modes, use FAV to scan favorite channels and/or all channels. See Using Channel Scan and Programming Favorite Channel Scan. 5. Aim the remote control at the device and press POWER once. The device should turn off. If it does not respond, repeat steps 2 through 5, trying each code for your brand until you find one that works. If it still does not work, try Searching For Your Code. NOTE: If the device does not have a POWER key, press the (Play) key. 3. Enter 9 - 9 - 0. The LED will blink twice. 4. To view the code for the first digit, press 1 once.Wait 3 seconds, count the LED blinks (e.g., three blinks = 3) and write down the number. NOTE: If a code digit is "0", the LED will not blink. USING A MACRO With programming, the MACRO key on your One For All 8 Device Home Theater Universal Remote Control can be setup to perform a repetitive, time-consuming operation for easy, convenient access through the press of a single key. A macro can be used to control a home theater operation, to set a favorite channel, or for other multiple functions you would like to control with one key press (see examples below). Moreover, the MACRO key can hold up to 15 key presses total. NOTE: Programming a new macro over an existing one will erase the original macro. 4. Use the keypad to enter a favorite channel number (e.g., 031). Then press SET once. NOTE: If the original remote control required pressing an Enter key to change the channel, also press the Enter key after the channel number (e.g., 0 -3-1-Enter). 8 DEVICE HOME THEATER UNIVERSAL REMOTE CONTROL Use CH+ (or CH-) to select the next higher (or lower) channel. device. However, you may change the Volume Lock setting to Global Volume Lock so that a device's volume will be locked to one mode (e.g., to control TV volume in all other modes).After that, if desired, you can perform Individual Volume Unlock on a selected device to set its volume control for independent operation. SOLUTION: Try all listed codes for the device brands being set up. Make sure they can be operated with an infrared remote control. PROBLEM: TV/VCR combo does not respond properly. SOLUTION: Use the VCR codes for your brand. Some combo units may require both a TV code and a VCR code for full operation. PROBLEM: Changing channels does not work properly. SOLUTION: If original remote control required pressing ENTER to change channels, press ENTER on the remote control after entering the channel number. PROBLEM: Tried Search For Your Code method and still could not find a working code. 6. Repeat steps 1 through 5 for each device you want to control. For future reference, write down each working device code in the boxes below: TV Code: VCR Code: DVD Code: 5. Repeat step 4 three more times for remaining digits. Use 2 for the second digit, 3 for the third digit, and 4 for the fourth digit. 6. To check for codes of other devices, repeat steps 1 through 5, but substitute the appropriate device key for each device you are checking. 5. If desired, repeat step 4 (in this section) for each favorite channel to be stored, up to a total of 10 channels. NOTE: If you try entering more than 10 channels, the remote control will automatically exit programming. Locking Volume Control To One Mode (Global Volume Lock): 1. Press and hold SET until the LED (red light) blinks twice, then release SET. 2. Enter 9 - 9 - 3 and then press any mode key once (e.g., TV). The LED will blink twice. 3. Now, when you press VOL+, VOL­, or MUTE, the volume of the selected device (e.g., TV) will be controlled regardless of the mode you have selected. Press PREV once to recall the last-viewed channel and to page back one screen on the main menu. In the CD mode, use PREV to turn random play on or off. SU RROUND SOUND 6. To exit programming, press and hold SET for 3 seconds. The LED will blink twice. Example ­ Programming A Favorite Channel In the RCVR/AMP mode, use PREV to select the receiver band. Use the keypad (1 ~ 9 and 0) to directly select channels (for example, 009 or 031). In the RCVR/AMP mode, use the keypad (1 ~ 9 and 0) to select audio sources 1 through 10. Press ENTER once after entering the channel numbers on some TVs. In the CD mode, use ENTER to add 10 to the digit entry (e.g., ENTER and 7 is 17). Use TV/VID to switch the TV's input to view TV or video programs. Use the transport keys to control your VCR, DVD or CD player, or VOD (Video On Demand) if available on your cable or satellite service. USING THE HOME THEATER MODE SAT Code: CBL Code: RCVR/AMP Code: CD Code: AUX Code: Aux. Device Type: _______________________________ The One For All 8 Device Home Theater Universal Remote Control includes a custom Home Theater mode. After the HOME THEATER key is programmed, it will allow you to access five groups of remote control keys without having to change device modes. With so many channels available through your cable or satellite system provider, you can program a macro that directly selects a favorite channel with one key press. For example, let's assume your favorite cable programs are on channel 71. Use the following instructions to program a macro for direct access of this channel: NOTE: This example assumes the TV tuner is connected directly to the cable line and not through a cable box. USING KEYMOVER The One For All 8 Device Home Theater Universal Remote Control includes a Keymover feature that allows you to map (or copy) keys from one mode (i.e., source mode) to another mode (i.e., destination mode). NOTE: The following keys cannot be used as a source or destination: TV, VCR, DVD, AUX, SAT, HOME THEATER, CD, CBL, RCVR/AMP, and SET. Unlocking Volume Control For A Single Device (Individual Volume Unlock): 1. After performing Global Volume Lock (above), press and hold SET again until the LED (red light) blinks twice, then release SET. 2. Press a desired mode key where you want volume to be unlocked (e.g., RCVR/AMP) and controlled within its own mode. 3. Enter 9 - 9 - 3 and then press VOL­ once. The LED will blink four times. 4. If desired, repeat steps 1 through 3 (of this section) for each device that you want volume to be unlocked. 5. Now, after you select a device that has volume unlocked (e.g., RCVR/AMP), pressing VOL+, VOL­, or MUTE, will control the device's volume only in its own mode. SOLUTION: Clear the device key as follows: Press and hold SET until the LED (red light) blinks twice, then release. Next enter 9 - 9 - 2. Then press the device key to be cleared twice. Now repeat the Search For Your Code method. PROBLEM: Remote control does not turn on Sony or Sharp TV/VCR Combo. Control Organization About Control Groups For Home Theater programming, the remote control's keys are grouped by type of control into the following five control groups: (1) Transport Controls: (2) Volume Controls: (3) Channel Controls: PLAY, STOP, FWD, REW, PAUSE, and REC VOL+, VOL-, and MUTE CH+, CH-, (Keypad) 0 ~ 9, ENTER, LAST, SLEEP, INFO, and TV/VCR MENU, GUIDE, Cursor Controls (Up, Down, Left, Right), SELECT, and EXIT PIP, MOVE, and SWAP 1. Press and hold SET until the LED (red light) blinks twice, then release SET. 2. Enter 9 - 9 - 5. The LED will blink twice. 3. Press MACRO once. 4. Press TV once. 5. Enter the channel number, 7 - 1. NOTE: If you have access to over 100 channels, enter 0 -7-1. Moreover, if the original remote control required pressing an Enter key to change the channel, also press the Enter key after the channel number (e.g., 0 -7-1-Enter). Programming Keymover For example, if your VCR does not have volume control, you can map the volume and mute keys from the TV mode to the VCR mode as follows: 1. Press and hold SET until the LED (red light) blinks twice, then release SET. 2. Enter 9 - 9 - 4. The LED will blink twice. 3. For the source mode, press TV once. 4. For the source key, press VOL+ once. 5. For the destination mode, press VCR once. 6. For the destination key, press VOL + once. 7. The LED will blink twice indicating the keymoved sequence is correct. 8. Repeat steps 1 through 7 twice more, substituting VOL­ and MUTE as source and destination keys in steps 4 and 6. Upon completion of the above procedure, you can now use your One For All 8 Device Home Theater Universal Remote Control to control the TV's volume and mute in the VCR mode, as well as in the TV mode. SOLUTION: For power on, these products require programming TV codes. For Sony, use TV code 0000 and VCR code 0032. For Sharp, use TV code 0093 and VCR code 0048. PROBLEM: CH+ and CH- do not work for your RCA TV. SOLUTION: Due to RCA design (1983-1987), only the original remote control will operate these functions. PROBLEM: No remote control of volume. SOLUTION: See Changing Volume Lock to lock/unlock volume. Unlocking All Volume Control (Restoring Default Setting): NOTE: Performing these instructions will restore independent volume control for all programmed devices (e.g., TV volume control in TV mode, VCR volume in VCR mode, etc.). PROGRAMMING TV/VCR COMBO CONTROL Perform the following instructions to control a TV/VCR Combo: 1. Turn on the TV/VCR Combo and insert a video cassette. NOTE: Please read steps 2 through 4 completely before proceeding. Highlight or write down the codes and device you wish to program before starting step 2. (4) Menu Controls: (5) PIP Controls: About Device Groups 6. Press and hold SET until the LED blinks twice, then release SET. Now when you press MACRO, you will instantly see cable channel 71 on your TV set. USER'S GUIDE To record a VCR program, press REC twice. After programming, press MACRO once to run a desired macro (see Using A Macro). Moreover, the remote control's devices are grouped into the following five device groups: (1) Device Group 1: (2) Device Group 2: (3) Device Group 3: (4) Device Group 4: (5) Device Group 5: (1) Device Group 1: (2) Device Group 2: (3) Device Group 3: (4) Device Group 4: (5) Device Group 5: VCR, DVD, CD, and RCVR/AMP TV, VCR, CBL, SAT, CD, and RCVR/AMP TV, VCR, CBL, SAT, CD, and RCVR/AMP TV, VCR, CBL, SAT, and DVD TV VCR TV CBL CBL TV 1. On the remote control, press and hold SET until the LED (red light) blinks twice, then release SET. 2. Enter 9 - 9 - 3 and then press VOL+ once. The LED will blink four times. 3. Volume will again be independently controlled according to its default states for all programmed devices. CUSTOMER SUPPORT For assistance, please contact us in any of the following ways: · E-mail: ofasupport@ueic.com · Internet: http://www.oneforall.com · Consumer Help Line: (330) 405-8615 2. On the remote control, press VCR. 3. Press and hold SET until the LED (red light) blinks twice, then release SET. 4. Use the Setup Codes For TV/VCR Combos (on the back) to locate the brand name and then enter the first four-digit code for your device. If performed correctly, the LED will blink twice. NOTE: If the LED did not blink twice, repeat steps 2 through 4 and try entering the same code again. INTRODUCTION The One For All 8 Device Home Theater Universal Remote Control is designed to operate up to eight home entertainment devices, including TV, video, and audio components. The remote control requires two (2) new AA alkaline batteries (not included) and easy programming to control your devices. For best results, please read and perform all instructions listed here.Also, keep these instructions for future reference. Use PIP to switch the Picture-In-Picture feature on or off (if available on your TV). Use MOVE to move the window picture to different positions in the main picture. Use SWAP to switch images and sound between the main and window pictures. Press SLEEP to activate your device's sleep timer (not available for all devices). Use to turn on or off the key backlight. When this feature is activated, keys will remain backlight for 5 seconds after the last key press. Use SET for all programming sequences. Example ­ Programming A Master Power Key With Instant Channel Selection A macro can be programmed to turn on and off your equipment as well. For example, let's set up a sequence that will turn on the TV and tune it to channel 3, and then turn on the Cable Box and tune it to a premium channel (e.g., 11). NOTE: This example assumes all equipment is turned off and that the TV is connected through the cable box with TV tuning set to channel 3. ABOUT UPGRADING The One For All 8 Device Home Theater Universal Remote Control has the largest infrared code library available. However, if you purchase a brand new home entertainment or home automation device, it may not respond to the codes stored in the remote control's memory. If this happens, please contact our Customer Support department (see Customer Support below) to upgrade the remote control. The Customer Support representative will search our entire database for a code that matches your device and instruct you how to enter it into your One For All 8 Device Home Theater Universal Remote Control. If the code for your home ...