Use VOL+ (or VOL-) to raise (or lower) the sound volume. SETTING UP YOUR COMPONENTS The One For All 8 Device Home Theater Universal Remote Control is preprogrammed at the factory to operate an RCA TV and VCR, a Motorola (GI) cable box, an RCA satellite receiver, a Pioneer CD player, a Toshiba DVD player, a Pioneer audio receiver/ amplifier, and a One For All home automation device. To control devices other than the default brands, perform the following steps; otherwise skip this section: NOTE: For TV/VCR Combo control, see the next section. TV/VCR Code: TV Code (if used): 4. 8 DEVICE HOME THEATER UNIVERSAL REMOTE CONTROL Press MUTE once to turn the sound off or on. In TV, VCR, DVD, SAT, and CBL modes, use FAV to scan favorite channels and/or all channels. (See Using Channel Scan and Programming Favorite Channel Scan.) ND Select a device. For this example, press VCR once. Then assign a desired Control Group to the device. For this example, press PLAY once, which will assign the entire group of Transport Controls (i.e., PLAY, STOP, FWD, REW, PAUSE, and REC) to the VCR. The LED will blink once. Select another device. For this example, press TV once. Then assign a desired Control Group to this device. For this example, press VOL+ once, which will assign the entire group of Volume Controls (i.e., VOL+, VOL-, and MUTE) to the TV. The LED will blink once. Select another device. For this example, press CBL once. Then assign a desired Control Group to this device. For this example, press CH+ once, which will assign the entire group of Channel Controls (i.e., CH+, CH-, (Keypad) 0 ~ 9, ENTER, LAST, SLEEP, INFO, and TV/VCR) to the Cable Box. The LED will blink once. To add additional Menu functionality to the Cable Box, press CBL once. Then press MENU once. This action will assign the entire group of Menu Controls (i.e., MENU, GUIDE, Cursor Controls (Up, Down, Left, Right), SELECT, and EXIT) to the Cable Box. The LED will blink once. To add PIP functionality to the TV, press TV once. Then press PIP once. This action will assign the entire group of PIP Controls (i.e., PIP, MOVE, and SWAP) to the TV. The LED will blink once. To exit Home Theater , press and release the SET key. The LED (red light) blinks twice. Now when you press MACRO once, the TV will turn on and tune to channel 03. Then the cable box will turn on and tune to channel 11. Restoring Keymoved Keys to Default Settings Restoring A Single Keymoved Key Unlocking All Volume Control (Restoring Default Setting): NOTE: Performing these instructions will restore independent volume control for all programmed devices (e.g., TV volume control in TV mode, VCR volume in VCR mode, etc.). Clearing A Macro 1. 2. 3. 4. Press and hold SET until the LED (red light) blinks twice, then release SET. Enter 9 - 9 - 5. The LED will blink twice. Press MACRO once. Press and hold SET until the LED blinks twice, then release SET. 1. Press a device key that has a keymoved key. 2. 3. Press and hold SET until the LED (red light) blinks twice, then release SET. Enter 9 - 9 - 4. The LED will blink twice. SEARCHING FOR YOUR CODE If your device does not respond to the remote control after trying all codes listed for your brand, or if your brand is not listed at all, try searching for your code. For example, to search for a code for your TV: 1. 2. 3. On the remote control, press TV once. Press and hold SET until the LED (red light) blinks twice, then release SET. Enter 9 - 9 - 1. The LED will blink twice. Aim the remote control at the the TV and slowly alternate between pressing POWER and TV. Stop when the TV turns off. NOTE: In the search mode, the remote control will send IR codes from its library to the selected device, starting with the most popular code first. 5. 1. 2. On the remote control, press and hold SET until the LED (red light) blinks twice, then release SET. Enter 9 - 9 - 3 and then press VOL+ once. The LED will blink four times. 1. Turn on a device (e.g.,VCR or DVD player) and, if applicable, insert media (e.g., cassette or disc). NOTE: Please read steps 2 through 4 completely before proceeding. Highlight or write down the codes and device you wish to program before starting step 2. 4. Press the destination key twice (where the keymoved key is stored). The LED will blink twice. Restoring All Keymoved Keys In A Single Mode 6. 3. Volume will again be independently controlled according to its default states for all programmed devices. 1. USING CHANNEL SCAN In the TV, VCR, DVD, SAT, and CBL modes, use the FAV key to start a 3-second scan of all favorite channels (if programmed ­ see Programming Favorite Channel Scan below) and/or all channels for the selected mode. 1. If Favorite Channel Scan has been set up, skip to step 2. Otherwise, press TV, VCR, DVD, SAT, or CBL once. 2. Press and hold SET until the LED (red light) blinks twice, then release SET. Enter 9 - 9 - 4. The LED will blink twice. ABOUT UPGRADING The One For All 8 Device Home Theater Universal Remote Control has the largest infrared code library available. However, if you purchase a brand new home entertainment or home automation device, it may not respond to the codes stored in the remote control's memory. If this happens, please contact our Customer Support department (see Troubleshooting Section below) to upgrade the remote control. The Customer Support representative will search our entire database for a code that matches your device and instruct you how to enter it into your One For All 8 Device Home Theater Universal Remote Control. If the code for your home entertainment or home automation device is not in our database,we will need to "capture" the code for that device from its original remote control. A new code would then be created and entered into your One For All 8 Device Home Theater Universal Remote Control.If necessary,the Customer Support representative can instruct you how to begin the capture procedure. NOTE: One For All reserves the right to replace a returned remote control with a new one of equal or superior functionality. 2. SO UN D SURROU Use CH+ (or CH-) to select the next higher (or lower) channel. On the remote control, press a device key once (i.e., TV, VCR, DVD, AUX, SAT, CBL, RCVR/AMP, or CD). NOTE: Use the AUX key to program control of home automation devices or miscellaneous audio services and video accessories. Alternately, use the AUX key to program control of a second device type (e.g., a second VCR; see "Re-assigning Device Keys"). 7. 3. Press the destination mode twice (where keymoved keys are stored). The LED will blink twice. 4. RE-ASSIGNING DEVICE KEYS The One For All 8 Device Home Theater Universal Remote Control can be set to control a second TV,VCR, DVD player, or other device. For example, to control a TV, a cable box, and two VCRs, you will need to re-assign the unused AUX key to operate the second VCR as follows: 1. On the remote control, press and hold SET until the LED (red light) blinks twice, then release SET. Enter 9 - 9 - 2. The LED will blink twice. Press VCR once, then press AVX once. Press PREV once to recall the last-viewed channel and to page back one screen on main menu. In the RCVR/AMP mode, use PREV to select the receiver band. 3. the Press and hold SET until the LED (red light) blinks twice, then release SET. 8. 5. 4. Use the Manufacturer's Codes (on the back) to locate the type of device and brand name and then enter the first four-digit code for your device. If performed correctly, the LED will blink twice. NOTE: If the LED did not blink twice, repeat steps 2 through 4 and try entering the same code again. To lock in the code, press and hold SET until the LED blinks twice, then release SET. 9. 6. To search for the codes of your other devices, repeat steps 1 through 5, but substitute the appropriate device key for the device you are searching for. 2. Press FAV once. · If Favorite Channel Scan has been set up, scanning of favorite channels will start and, upon completion, continue to scan all channels upward for the same device. · If Favorite Channel Scan has not been set up, scanning will start with the current channel, then proceed to the next channel up, and continue until all channels of the selected device is scanned. Operating The Home Theater Mode After programming the Home Theater key (see the previous section), you simply activate this mode by pressing HOME THEATER once. Instantly, groups of remote control keys will be assigned to their programmed devices. For the above example, pressing HOME THEATER once would assign the following keys to the VCR, TV, and Cable Box: VCR: TV: Cable Box: PLAY, STOP, FWD, REW, PAUSE, and REC VOL+, VOL-, MUTE, PIP, MOVE, and SWAP CH+, CH-, (Keypad) 0 ~ 9, ENTER, LAST, SLEEP, INFO, TV/VCR, MENU, GUIDE, Cursor Controls (Up, Down, Left, Right), SELECT, and EXIT Use the keypad (1 ~ 9 and 0) to directly select channels (for example, 009 or 031). In the RCVR/AMP mode, use the keypad (1 ~ 9 and 0) to select audio sources 1 through 10. Press ENTER once after entering the channel numbers on some TVs. Use TV/VID to switch the TV's input to view TV or video programs. Use the transport keys to control your VCR, DVD player, or VOD (Video On Demand) if available on your cable or satellite service. 2. 3. 5. Aim the remote control at the device and press POWER once. The device should turn off. If it does not respond, repeat steps 2 through 5, trying each code for your brand until you find one that works. If it still does not work, try Searching For Your Code. NOTE: If the device does not have a POWER key, press the (Play) key. CHECKING THE CODES If you have set up the remote control using the Searching For Your Code procedure, you may need to find out which four-digit code is operating your equipment. For example, to find out which code is operating your TV: 1. 2. 3. On the remote control, press TV once. Press and hold SET until the LED (red light) blinks twice, then release SET. Enter 9 - 9 - 0. The LED will blink twice. Upgrade Exclusions · Home entertainment or home automation devices controlled by radio frequency (RF/UHF), wired, or ultrasonic remote controls. Only devices controlled by infrared remote controls are covered. 3. To stop scanning channels at any time, press any key once (except the backlight key ). 6. Repeat steps 1 through 5 for each device you want to control. For future reference, write down each working device code in the boxes below: TV Code: VCR Code: DVD Code: SAT Code: 4. The AUX key is now ready to be programmed for your second VCR. (See Setting Up Your Components.) To re-assign other device keys to the AUX key, repeat steps 1 through 4 above by substituting the sequence from the below chart: · Home entertainment or home automation devices not controlled by remote controls. · Broken or defective product. · Products that operate over 100 kHz. · Infrared keyboards and infrared pointing devices (such as mouse substitutes). · All products for sale and/or use outside the continental United States, Hawaii,Alaska, or Canada. PROGRAMMING FAVORITE CHANNEL SCAN In the TV, VCR, DVD, SAT, or CBL mode, you can store a list of up to 10 favorite channels, in any order, that will be immediately scanned when FAV is pressed (see Using Channel Scan). NOTE: Only channels of one mode can be stored for Favorite Channel Scan. To Re-Assign Device Key AUX as 2nd TV key: AUX as 2nd DVD key: AUX as 2nd SAT key: AUX as 2nd CD key: AUX as 2nd CBL key: AUX as 2nd RCVR/AMP key: Perform Sequence SET - 9 - 9 - 2 - TV - AUX SET - 9 - 9 - 2 -DVD- AUX SET - 9 - 9 - 2 -SAT- AUX SET - 9 - 9 - 2 -CD- AUX SET - 9 - 9 - 2 -CBL- AUX SET - 9 - 9 - 2 - RCVR/AMP - AUX USER'S GUIDE INTRODUCTION The One For All 8 Device Home Theater Universal Remote Control is designed to operate up to eight home entertainment devices, including TV, video, and audio components. The remote control requires two (2) new AA alkaline batteries (not included) and easy programming to control your devices. For best results, please read and perform all instructions listed here.Also, keep these instructions for future reference. To record a VCR program, press REC twice. 4. To view the code for the first digit, press 1 once.Wait 3 seconds, count the LED blinks (e.g., three blinks = 3) and write down the number. NOTE: If a code digit is "0", the LED will not blink. USING A MACRO With programming, the MACRO key on your One For All 8 Device Home Theater Universal Remote Control can be setup to perform a repetitive, time-consuming operation for easy, convenient access through the press of a single key. A macro can be used to control a home theater operation, to set a favorite channel, or for other multiple functions you would like to control with one key press (see examples below). Moreover, the MACRO key can hold up to 15 key presses total. NOTE: Programming a new macro over an existing one will erase the original macro. 1. On the remote control, press TV, VCR, ...