CTGRD3N 3110 manual booklet.QXD 5/2/06 3:08 PM Page 1 TABLE OF CONTENTS Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Features And Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Key Charts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Installing Batteries. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Setting Up Your Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Programming TV/VCR Combo Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Programming TV/DVD Combo Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Searching For Your Code. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Checking The Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Re-Assigning Device Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Changing Volume Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 To Change Volume Lock To Another Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Unlocking Volume Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Instructions To The User . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Lifetime Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Additional Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Manufacturer's Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Setup Codes For Cable Boxes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Setup Codes For Cable Box / PVR (or DVR) Combos. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Setup Codes For Satellite Receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Setup Codes For Satellite Receiver / PVR (or DVR) Combos. . . . . . . . . . . . . . . . . . . . . . . 12 Setup Codes For TVs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Setup Codes For VCRs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Setup Codes For PVRs (or DVRs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Setup Codes For TV/VCR Combos . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Setup Codes For DVD Players . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Setup Codes For DVD Players / VCR Combos . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Setup Codes For TV/DVD Player Combos . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Setup Codes For TV/VCR/DVD Player Combos . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 2 CTGRD3N 3110 manual booklet.QXD 5/2/06 3:08 PM Page 3 INTRODUCTION The One For All 3 Devices Universal Remote Control is designed to operate three home entertainment devices, depending on the model purchased (see Key Charts, Mode Keys on the right). The remote control requires two fresh AAA alkaline batteries (not included) and easy programming to control your devices.For best results, please read and perform all instructions listed here.Also, keep these instructions for future reference. FEATURES AND FUNCTIONS Use the Key Charts to learn how to use the universal functions of the One For All 3 Devices Universal Remote Control. Key Charts The LED (red light) blinks to show that the remote control is working and is sending signals. Use SET for all programming sequences. Press POWER once to turn on or off the selected device. Device Keys for 3 Devices: Press VCR/DVD, CBL/SAT, or TV once to select a home entertainment device to control. Press SLEEP to activate your device's sleep timer (not available for all devices). Use TV/VID to switch the TV's input to view TV or video program. Use the keypad (0 ~ 9) to directly select channels (for example, 09 or 31). Press ENTER once after entering channel numbers on some TV models. Press PREV CH once to recall the last-viewed channel and to page back one screen on the main menu. Press MUTE once to turn sound off or on. Use MENU (or EXIT) to choose options (or exit) from your selected device's menu or guide. Use CH + (or CH -) to select the next higher(or lower) channel. Use VOL+ (or VOL-) to raise (or lower) the sound volume. When controlling a DVD player, use SKIP FORWARD to next DVD chapter., use SKIP REVERSE to the last DVD chapter. Press SHIFT and use the Up/Down/Left/ Right cursor keys to move the cursor in the program guide and menu screens. Press SHIFT and MUTE to select a menu item. Use the transport keys to control your VCR, CD or DVD player, or VOD. To record a program, press the record key (REC) twice. 3 4 CTGRD3N 3110 manual booklet.QXD 5/2/06 3:08 PM Page 5 INSTALLING BATTERIES 1. On the remote control's back, push the tab and lift off the battery cover. 4. NOTE: If the LED did not blink twice, then repeat steps 2 through 3 and try entering the same code again. Aim the remote control at the device and press POWER once. The device should turn off. If it does not respond, repeat steps 2-3, trying each code for your brand until you find one that works. If it still does not work, try Searching For Your Code. NOTE: If the device does not have a POWER key, press the (PLAY) key. 5. Repeat steps 1 through 4 for each device you want to control. 2. Obtain two (2) new AAA alkaline batteries. Match the + and ­ marks on the batteries to the + and ­ marks in the battery case, then insert the new batteries. PROGRAMMING TV/VCR COMBO CONTROL Perform the following instructions to control a TV/VCR Combo: 1. Turn on the TV/VCR Combo and insert a video cassette. NOTE: Please read steps 2-4 completely before proceeding. Highlight or write down the codes and device you wish to program before moving on to step 2. 2. 3. Press the battery cover back into place. The tab should click when the cover is locked. On the remote control, press VCR/DVD. Press and hold SET until the LED blinks twice, then release SET. 3. Use the Setup Codes For TV/VCR Combos (on page 12) to locate the brand name and then enter the first four-digit code for your device. If performed correctly, the LED will blink twice. NOTE: If the LED did not blink twice, then repeat steps 2 through 3 and try entering the same code again. 4. Test the unit by pressing POWER and any mode key (e.g., TV). If the batteries are inserted correctly, the LED will blink once. NOTE: When batteries need replacement, the remote control will stop operating. Remove the old batteries and insert new ones within 30 minutes to ensure all of your programming information is restored. 4. Aim the remote control at the device and press POWER once. It should turn off. If the device does not respond, repeat steps 2-3, trying each code for your brand until you find one that works. If it still does not work, try Searching For Your Code. NOTE: If the device does not have a POWER key, press the (PLAY) key. SETTING UP YOUR COMPONENTS The One For All 3 Devices remote control is preprogrammed at the factory to operate an RCA TV and VCR, a Motorola (GI) cable box, and a Toshiba DVD player. To control devices other than the default brands, perform the following steps; otherwise skip this section: NOTE: For TV/VCR Combo control, see the next section. PROGRAMMING TV/DVD COMBO CONTROL Perform the following instructions to control a TV/DVD Combo: 1. Turn on your TV/DVD and insert a disc. 2. On the remote control, press VCR/DVD. Press and hold SET until LED blinks twice, then release SET. 3. Use the Setup Codes For TV/DVD Combos (on page 12) to locate the brand name and then enter the first fourdigit code for your device. If performed correctly, the LED will blink twice. 4. Aim the remote control at your TV/DVD and press POWER. Your TV/DVD should turn off. If your original TV/DVD remote control did not have a POWER key, press PLAY.Your TV/DVD should start to play. If your TV/DVD does not respond, repeat steps 2-4, trying each code listed for your brand until you find the one that operates your TV/DVD. 1. Turn on a device (e.g.,VCR) and, if applicable, insert media, (e.g., cassette or disc). NOTE: Please read steps 2-4 completely before proceeding. Highlight or write down the codes and device you wish to program before moving on to step 2. 2. On the remote control, press a device key once (i.e., VCR/DVD, CBL/SAT, or TV). Press and hold SET until the LED blinks twice, then release SET. 3. Use the Manufacturer's Codes (starting on page 11) to locate the type of device and brand name and then enter the first four-digit code for your component. If performed correctly, the LED will blink twice. 5. Your One For All 3 Devices is now programmed to operate your TV/DVD.Write your TV/DVD code for future reference. Remember, if you want to use your One For All 3 Devices to operate your TV/DVD, press the VCR/DVD key first. 5 6 CTGRD3N 3110 manual booklet.QXD 5/2/06 3:08 PM Page 7 SEARCHING FOR YOUR CODE If your device does not respond to the remote control after trying all codes listed for your brand, or if your brand is not listed at all, try searching for your code. For example, to search for a code for your TV: 1. 2. On the remote control, press TV once. Press and hold SET until the LED blinks twice, then release SET. 2. 3. Enter 9 - 9 - 2. The LED will blink twice. Press TV once, then press VCR/DVD once. 4. The VCR/DVD key is now ready to be programmed for your second TV. (see Setting Up Your Components). To re-assign other device keys, repeat steps 1 through 4 by substituting the key sequence from the below chart for the most popular components: 3. 4. Enter 9 - 9 - 1. The LED will blink twice. Aim the remote control at the the TV and slowly alternate between pressing POWER and TV. Stop when the TV turns off. To Re-Assign Key VCR/DVD as 2nd TV key: VCR/DVD as 2nd CBL key: VCR/DVD as 2nd SAT key: VCR/DVD back to VCR/DVD: Sequence Perform SET - 9 - 9 - 2 - TV - VCR/DVD SET - 9 - 9 - 2 - CBL/SAT - VCR/DVD SET - 9 - 9 - 2 - CBL/SAT - VCR/DVD SET - 9 - 9 - 2 - VCR/DVD - VCR/DVD NOTE: In the search mode, the remote control will send IR codes from its library to the selected device, starting with the most popular code first. 5. To lock in the code, press and hold SET until the LED blinks twice, then release SET. When a re-assignment is done, the LED will blink twice to confirm your choice.At that time, you will need to program the remote control for the new device (see Setting Up Your Components). 6. To search for the codes of your other devices, repeat steps 1 through 5, but substitute the appropriate device key for the device you are searching for. CHANGING VOLUME LOCK The One For All 3 Devices is set to control the volume of your TV in the TV,VCR, CBL/SAT, and DVD modes. If you want the volume to be controlled by a mode other than TV (e.g., CBL/SAT), change the Volume Lock as follows: CHECKING THE CODES If you have set up the remote control using the Searching For Your Code procedure, you may need to find out which four-digit code is operating your equipment: For example, to find out which code is operating your TV: 1. 2. 3. On the remote control, press TV once. Press and hold SET until the LED blinks twice, then release SET. To Change Volume Lock To Another Mode: 1. 2. 3. On the remote control, press and hold SET until the LED blinks twice, then release SET. Enter 9 - 9 - 3 and then press any mode key once (except TV). The LED will blink twice. Now, whenever you press VOL+, or VOL­, volume will be controlled by your mode choice. Enter 9 - 9 - 0. The LED will blink twice. 4. To view the code for the first digit, press 1 once.Wait 3 seconds, count the LED blinks (e.g., 3 blinks = 3) and write down the number. NOTE: If a code digit is "0", the LED will not blink. Unlocking Volume Control: NOTE: Perform these instructions when you want independent volume control for each ...