Use CH+ (or CH-) to select the next higher (or lower) channel. TV Code: VCR Code: USING THE HOME THEATER MODE The One For All 6 Device Home Theater Universal Remote Control includes a custom Home Theater mode. After the HOME THEATER key is programmed, it will allow you to access five groups of remote control keys without having to change device modes. Example ­ Programming A Favorite Channel With so many channels available through your cable or satellite system provider, you can program a macro that directly selects a favorite channel with one key press. For example, let's assume your favorite cable programs are on channel 71. Use the following instructions to program a macro for direct access of this channel: NOTE: This example assumes the TV tuner is connected directly to the cable line and not through a cable box. USING KEYMOVER The One For All 6 Device Home Theater Universal Remote Control includes a Keymover feature that allows you to map (or copy) keys from one mode (i.e., source mode) to another mode (i.e., destination mode). NOTE: The following keys cannot be used as a source or destination: TV, VCR, DVD, SAT, HOME THEATER, CBL, RCVR/AMP, and SET. Unlocking Volume Control For A Single Device (Individual Volume Unlock): 1. After performing Global Volume Lock (above), press and hold SET again until the LED (red light) blinks twice, then release SET. 2. Press a desired mode key where you want volume to be unlocked (e.g., RCVR/AMP) and controlled within its own mode. 3. Enter 9 - 9 - 3 and then press VOL­ once. The LED will blink four times. 4. If desired, repeat steps 1 through 3 (of this section) for each device that you want volume to be unlocked. 5. Now, after you select a device that has volume unlocked (e.g., RCVR/AMP), pressing VOL+, VOL­, or MUTE, will control the device's volume only in its own mode. PROBLEM: No remote control of volume. SOLUTION: See Changing Volume Lock to lock/unlock volume. 6 DEVICE HOME THEATER UNIVERSAL REMOTE CONTROL Press PREV once to recall the last-viewed channel and to page back one screen on the main menu. In the RCVR/AMP mode, use PREV to select the receiver band. Use the keypad (1 ~ 9 and 0) to directly select channels (for example, 009 or 031). DVD Code: SAT Code: CBL Code: RCVR/AMP Code: CUSTOMER SUPPORT For assistance, please contact us in any of the following ways: · E-mail: ofasupport@ueic.com · Internet: http://www.oneforall.com · Consumer Help Line: (330) 405-8615 Control Organization About Control Groups For Home Theater programming, the remote control's keys are grouped by type of control into the following five control groups: (1) Transport Controls: (2) Volume Controls: (3) Channel Controls: PLAY, STOP, FWD, REW, PAUSE, and REC VOL+, VOL-, and MUTE CH+, CH-, (Keypad) 0 ~ 9, ENTER, LAST, SLEEP, INFO, and TV/VCR MENU, GUIDE, Cursor Controls (Up, Down, Left, Right), SELECT, and EXIT PIP, MOVE, and SWAP Programming Keymover For example, if your VCR does not have volume control, you can map the volume and mute keys from the TV mode to the VCR mode as follows: 1. Press and hold SET until the LED (red light) blinks twice, then release SET. 2. Enter 9 - 9 - 4. The LED will blink twice. 3. For the source mode, press TV once. 4. For the source key, press VOL+ once. 5. For the destination mode, press VCR once. 6. For the destination key, press VOL + once. 7. The LED will blink twice indicating the keymoved sequence is correct. 8. Repeat steps 1 through 7 twice more, substituting VOL­ and MUTE as source and destination keys in steps 4 and 6. Upon completion of the above procedure, you can now use your One For All 6 Device Home Theater Universal Remote Control to control the TV's volume and mute in the VCR mode, as well as in the TV mode. 1. Press and hold SET until the LED (red light) blinks twice, then release SET. 2. Enter 9 - 9 - 5. The LED will blink twice. 3. Press MACRO once. 4. Press TV once. 5. Enter the channel number, 7 - 1. NOTE: If you have access to over 100 channels, enter 0 -7-1. Moreover, if the original remote control required pressing an Enter key to change the channel, also press the Enter key after the channel number (e.g., 0 -7-1-Enter). LIMITED WARRANTY One For All® warrants, to the original purchaser only, that this product will be free from defects in materials and workmanship, under normal use, for ninety (90) days from the date of original purchase. This limited warranty is valid only on ONE FOR ALL® product purchased and used in the United States of America or Canada, and does not apply to products used for industrial or commercial purpose. The limited warranty does not cover damage or failure caused by products or services not supplied by ONE FOR ALL® , or which result from accident, misuse, abuse, neglect, mishandling, misapplication, faulty installation, set-up adjustment, improper maintenance, alteration, maladjustment of consumer controls, modifications, commercial use, or that is attributable to acts of God. There are no express warranties except as listed above. ONE FOR ALL® SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THIS PRODUCT OR ARISING OUT OF ANY BREACH OF WARRANTY. ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE,ARE LIMITED TO THE WARRANTY PERIOD SET FORTH ABOVE. Some states do not allow the exclusion or limitation of incidental or consequential damages, or limitations on how long an implied warranty lasts, so the above exclusions or limitations may not apply to you. This warranty gives you specific legal rights and you may also have other rights which vary from state to state. To obtain warranty service for a defective product during the warranty period, please return the product, preferably in the original carton, along with your purchase receipt, to the store of original purchase.A note detailing the complaint would be helpful. The store, at its option, will replace or repair this product if found to be defective. One For All (330) 405-8655 SU RROUND SOUND In the RCVR/AMP mode, use the keypad (1 ~ 9 and 0) to select audio sources 1 through 10. Press ENTER once after entering the channel numbers on some TVs. Use TV/VID to switch the TV's input to view TV or video programs. Use the transport keys to control your VCR, DVD player, or VOD (Video On Demand) if available on your cable or satellite service. To record a VCR program, press REC twice. After programming, press MACRO once to run a desired macro (see Using A Macro). Use PIP to switch the Picture-In-Picture feature on or off (if available on your TV). Use MOVE to move the window picture to different positions in the main picture. Unlocking All Volume Control (Restoring Default Setting): NOTE: Performing these instructions will restore independent volume control for all programmed devices (e.g., TV volume control in TV mode, VCR volume in VCR mode, etc.). PROGRAMMING TV/VCR COMBO CONTROL Perform the following instructions to control a TV/VCR Combo: 1. Turn on the TV/VCR Combo and insert a video cassette. NOTE: Please read steps 2 through 4 completely before proceeding. Highlight or write down the codes and device you wish to program before starting step 2. (4) Menu Controls: (5) PIP Controls: About Device Groups 1. On the remote control, press and hold SET until the LED (red light) blinks twice, then release SET. 2. Enter 9 - 9 - 3 and then press VOL+ once. The LED will blink four times. 3. Volume will again be independently controlled according to its default states for all programmed devices. Moreover, the remote control's devices are grouped into the following five device groups: (1) Device Group 1: (2) Device Group 2: (3) Device Group 3: (4) Device Group 4: (5) Device Group 5: (1) Device Group 1: (2) Device Group 2: (3) Device Group 3: (4) Device Group 4: (5) Device Group 5: VCR, DVD, and RCVR/AMP TV, VCR, CBL, SAT, and RCVR/AMP TV, VCR, CBL, SAT, and RCVR/AMP TV, VCR, CBL, SAT, and DVD TV VCR TV CBL CBL TV 6. Press and hold SET until the LED blinks twice, then release SET. Now when you press MACRO, you will instantly see cable channel 71 on your TV set. 2. On the remote control, press VCR. 3. Press and hold SET until the LED (red light) blinks twice, then release SET. 4. Use the Setup Codes For TV/VCR Combos (on the back) to locate the brand name and then enter the first four-digit code for your device. If performed correctly, the LED will blink twice. NOTE: If the LED did not blink twice, repeat steps 2 through 4 and try entering the same code again. Example ­ Programming A Master Power Key With Instant Channel Selection A macro can be programmed to turn on and off your equipment as well. For example, let's set up a sequence that will turn on the TV and tune it to channel 3, and then turn on the Cable Box and tune it to a premium channel (e.g., 11). NOTE: This example assumes all equipment is turned off and that the TV is connected through the cable box with TV tuning set to channel 3. ABOUT UPGRADING The One For All 6 Device Home Theater Universal Remote Control has the largest infrared code library available. However, if you purchase a brand new home entertainment or home automation device, it may not respond to the codes stored in the remote control's memory. If this happens, please contact our Customer Support department (see Customer Support on the right) to upgrade the remote control. The Customer Support representative will search our entire database for a code that matches your device and instruct you how to enter it into your One For All 6 Device Home Theater Universal Remote Control. If the code for your home entertainment or home automation device is not in our database,we will need to "capture" the code for that device from its original remote control. A new code would then be created and entered into your One For All 6 Device Home Theater Universal Remote Control.If necessary,the Customer Support representative can instruct you how to begin the capture procedure. NOTE: One For All reserves the right to replace a returned remote control with a new one of equal or superior functionality. The default Device Group setting from the factory is: Restoring Keymoved Keys to Default Settings Restoring A Single Keymoved Key USER'S GUIDE Use SWAP to switch images and sound between the main and window pictures. Press SLEEP to activate your device's sleep timer (not available for all devices). 5. Aim the remote control at the device and press POWER once. It should turn off. If the device does not respond, repeat steps 2 through 5, trying each code for your brand until you find one that works. If it still does not work, try Searching For Your Code. NOTE: If the device does not have a POWER key, press the (Play) key. 1. Press and hold SET until the LED (red light) blinks twice, then release SET. 2. Enter 9 - 9 - 5. The LED will blink twice. 3. Press MACRO once. 4. Enter the following sequence: TV, POWER, and 0 - 3 (or 0 -0 - 3 if access is over 100 channels) NOTE: If the original remote control required pressing an Enter key to change the channel, also press the Enter key after the channel number (e.g., 0 -7-1-Enter). 1. Press a device key that has a keymoved key. 2. Press and hold SET until the LED (red light) blinks twice, then release SET. 3. Enter 9 - 9 - 4. The LED will blink twice. 4. Press the destination key twice (where the keymoved key is stored). The LED will blink twice. Restoring All Keymoved Keys In A Single Mode INTRODUCTION The One For All 6 Device Home Theater Universal Remote Control is designed to operate up to six home entertainment devices, including TV, video, and audio components. The remote control requires two (2) new AA alkaline batteries (not included) and easy programming to control your devices. For best results, please read and perform all instructions listed here.Also, keep these instructions for future reference. Use to turn on or off the key backlight. When this feature is activated, keys will remain backlight for 5 seconds after the last key press. Use SET for all programming sequences. 6. If you've located a setup code that works, but it has a separate TV code, you'll also need to program it into the remote control to access volume control as follows: a. Press TV once. The LED (red light) will blink twice. b. Enter the TV code for your TV/VCR Combo. If correct, the LED will blink twice. NOTE: For VCR/TV Combos programmed with separate TV codes, TV volume is controlled by pressing VCR first and then TV. After that, use VOL+ (or VOL-) to raise (or lower) the TV volume. For other alternatives on controlling your volume keys, see the "Changing Volume Lock" or "Using Keymover" sections. Programming The Home Theater Mode For example, let's assume you have a TV, a cable box, and a VCR in your home theater system.You can set up the Home Theater mode so that selected controls are assigned to these devices as follows: 1. On th ...