User manual ONKYO HT-R430

Contents Introduction ..................................... 2 6.1ch Home Theater System HT-S680 AV Receiver (HT-R430) Front Speakers (SKF-330F L/R) Center Speaker (SKC-330C) Surround Speakers (SKM-330S L/R) Surround Back Speaker (SKB-330) Powered Subwoofer (SKW-420) Connection .................................... 17 Turning On & First Time Setup..... 32 Basic Operation Playing your AV components ....... 34 Using the Tuner............................ 36 Instruction Manual Enjoying the Listening Modes ..... 40 Thank you for purchasing an Onkyo 6.1ch Home Theater System. Please read this manual thoroughly before making connections and plugging in the unit. Following the instructions in this manual will enable you to obtain optimum performance and listening enjoyment from your new 6.1ch Home Theater System. Please retain this manual for future reference. Advanced Operation ..................... 44 Troubleshooting ............................ 52 Specification.................................. 54 En WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE. WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN AVIS RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. Important Safety Instructions 1. 2. 3. 4. 5. 6. 7. 8. Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with dry cloth. Do not block any ventilation openings. Install in accordance with the manufacturer's instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. Only use attachments/accessories specified by the manufacturer. Use only with the cart, stand, PORTABLE CART WARNING tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/ apparatus combination to avoid injury from tip-over. S3125A Unplug this apparatus during lightning storms or when unused for long periods of time. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. 15. Damage Requiring Service Unplug the apparatus from the wall outlet and refer servicing to qualified service personnel under the following conditions: A. When the power-supply cord or plug is damaged, B. If liquid has been spilled, or objects have fallen into the apparatus, C. If the apparatus has been exposed to rain or water, D. If the apparatus does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the apparatus to its normal operation, E. If the apparatus has been dropped or damaged in any way, and F. When the apparatus exhibits a distinct change in performance this indicates a need for service. 16. Object and Liquid Entry Never push objects of any kind into the apparatus through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. The apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases shall be placed on the apparatus. Don't put candles or other burning objects on top of this unit. 17. Batteries Always consider the environmental issues and follow local regulations when disposing of batteries. 18. If you install the apparatus in a built-in installation, such as a bookcase or rack, ensure that there is adequate ventilation. Leave 20 cm (8") of free space at the top and sides and 10 cm (4") at the rear. The rear edge of the shelf or board above the apparatus shall be set 10 cm (4") away from the rear panel or wall, creating a flue-like gap for warm air to escape. 9. 10. 11. 12. 13. 14. 2 Precautions 1. Recording Copyright--Unless it's for personal use only, recording copyrighted material is illegal without the permission of the copyright holder. 2. AC Fuse--The AC fuse inside the unit is not userserviceable. If you cannot turn on the unit, contact your Onkyo dealer. 3. Care--Occasionally you should dust the unit all over with a soft cloth. For stubborn stains, use a soft cloth dampened with a weak solution of mild detergent and water. Dry the unit immediately afterwards with a clean cloth. Don't use abrasive cloths, thinners, alcohol, or other chemical solvents, because they may damage the finish or remove the panel lettering. 4. Power WARNING BEFORE PLUGGING IN THE UNIT FOR THE FIRST TIME, READ THE FOLLOWING SECTION CAREFULLY. AC outlet voltages vary from country to country. Make sure that the voltage in your area meets the voltage requirements printed on the unit's rear panel (e.g., AC 230 V, 50 Hz or AC 120 V, 60 Hz). Some models have a voltage selector switch for compatibility with power systems around the world. Before you plug in such a model, make sure that the voltage selector is set to the correct voltage for your area. Setting the [STANDBY/ON] switch to STANDBY does not fully shutdown the unit. If you do not intend to use the unit for an extended period, remove the power cord from the AC outlet. 5. Never Touch this Unit with Wet Hands--Never handle this unit or its power cord while your hands are wet or damp. If water or any other liquid gets inside this unit, have it checked by your Onkyo dealer. 6. Handling Notes · If you need to transport this unit, use the original packaging to pack it how it was when you originally bought it. · Do not leave rubber or plastic items on this unit for a long time, because they may leave marks on the case. · This unit's top and rear panels may get warm after prolonged use. This is normal. · If you do not use this unit for a long time, it may not work properly the next time you turn it on, so be sure to use it occasionally. For U.S. models FCC Information for User CAUTION: The user changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. · Consult the dealer or an experienced radio/TV technician for help. For Canadian Models NOTE: THIS CLASS B DIGITAL APPARATUS COMPLIES WITH CANADIAN ICES-003. For models having a power cord with a polarized plug: CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. Modèle canadien REMARQUE: CET APPAREIL NUMÉRIQUE DE LA CLASSE B EST CONFORME À LA NORME NMB-003 DU CANADA. Sur les modèles dont la fiche est polarisée: ATTENTION: POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU'AU FOND. Memory Backup The AV receiver uses a battery-less memory backup system in order to retain radio presets and other settings when it's unplugged or in the case of a power failure. Although no batteries are required, the AV receiver must be plugged into an AC outlet in order to charge the backup system. Once it has been charged, the AV receiver will retain the settings for several weeks, although this depends on the environment and will be shorter in humid climates. 3 Speaker Precautions Placement · The subwoofer cabinet is made out of wood and is therefore sensitive to extreme temperatures and humidity, do not put it in locations subject to direct sunlight or in humid places, such as near an air conditioner, humidifier, bathroom, or kitchen. · Do not put water or other liquids close to the speakers. If liquid is spilled over the speakers, the drive units may be damaged. · Speakers should only be placed on sturdy, flat surfaces that are free from vibration. Putting them on uneven or unstable surfaces, where they may fall and cause damage, will affect the sound quality. · Subwoofer is designed to be used in the upright vertical position only. Do not use it in the horizontal or tilted position. · If the unit is used near a turntable or CD player, howling or slipping of sound may occur. To prevent this, move the unit away from the turntable or CD player otherwise lower the unit's output level. Features Amp · 6-channel amplifier · 100 watts per channel min. RMS at 8 , 2 channels driven from 1 kHz with no more than 0.9% total harmonic distortion · WRAT (Wide Range Amplifier Technology) · Optimum gain volume circuitry · OptiResponseTM Equalizer (OR-EQTM)*1 function Processing · Dolby*2 Digital EX and Dolby Pro Logic IIx · DTS, DTS-ES Matrix/Discrete, and DTS Neo:6 processing*3 · Cinema Filter function · Linear PCM 192 kHz/24-bit D/A converters on all channels · Powerful and highly accurate 32-bit DSP Processing Audio/Video Adjustable crossover (60, 80, 100, 120, 150 Hz) 3 S-Video inputs, 2 outputs 2 assignable digital inputs (1 optical, 1 coaxial) Subwoofer pre out Color-coded multichannel input for use with Super Audio CD and DVD-Audio · A/B speaker drive · Color-coded speaker terminal · · · · · Using Close to a TV or Computer TVs and computer monitors are magnetically sensitive devices and as such are likely to suffer discoloration or picture distortion when conventional speakers are placed nearby. To prevent this, the SKF-330F and SKC-330C feature internal magnetic shielding. In some situations, however, discoloration may still be an issue, in which case you should turn off your TV or monitor, wait 15 to 30 minutes, and then turn it back on again. This normally activates the degaussing function, which neutralizes the magnetic field, thereby removing any discoloration effects. If discoloration problems persist, try moving the speakers away from your TV or monitor. Note that discoloration can also be caused by a magnet or demagnetizing tool that's too close to your TV or monitor. Do not place SKM-330 and SKB-330 close to TV or a computer monitor because they have no magnetic shield. FM/AM Tuner · 30 FM/AM presets · FM/AM auto tuning · RDS (Radio Data System) (Europe only) Remote Controller · Remote controller can be used to control Onkyo CD, CDR, MD components, and cassette tape deck Input Signal Warning The speakers can handle the specified input power when used for normal music reproduction. If any of the following signals are fed to them, even if the input power is within the specified rating, excessive current may flow in the speaker coils, causing burning or wire breakage: 1. Interstation noise from an untuned FM radio. 2. Sound from fast-forwarding a cassette tape. 3. High-pitched sounds generated by an oscillator, electronic musical instrument, and so on. 4. Amplifier oscillation. 5. Special test tones from audio test CDs and so on. 6. Thumps and clicks caused by connecting or disconnecting audio cables (Always turn off your amplifier before connecting or disconnecting cables.) 7. Microphone feedback. Front / Center / Surround Speakers · Color-coded speaker terminals and speaker cables · 3-1/8" (8 cm) cone woofer · Ceramic tweeter Subwoofer · Built-in 150 watts power amplifier · 8" cone woofer · Auto Standby/On *1. OptiResponse and OR-EQ are trademarks of Onkyo Corporation. *2. Manufactured under license from Dolby Laboratories. "Dolby", "Pro Logic" and the double-D symbol are registered trademarks of Dolby Laboratories. *3. "DTS" and "Neo:6" are trademarks of Digital Theater Systems, Inc. 4 Table of Contents Introduction Important Safety Instructions .....................2 Precautions ..................................................3 Speaker Precautions ...................................4 Features ........................................................4 Supplied Accessories..................................6 Before Using the AV receiver .....................7 Front & Rear Panels.....................................8 Speaker Package .......................................11 Remote Controller......................................12 Basic Operation Playing Your AV Components ................. 34 Basic AV Receiver Operation .......................34 Using the Multichannel Input ........................35 Displaying Source Information......................35 Using the Tuner ......................................... 36 Listening to the Radio ...................................36 Tuning into Radio Stations ...........................36 Common Functions................................... 38 Using the OptiResponse Equalizer...............38 Setting the Display Brightness......................38 Adjusting the Bass & Treble .........................38 Muting the AV Receiver ................................38 Using the Sleep Timer ..................................39 Using Headphones .......................................39 Adjusting Speaker Levels .............................39 Connection Connecting Speakers ................................17 Enjoying Home Theater................................ 17 Speaker Connection Precautions................. 18 Connecting Speaker..................................... 18 Wall Mounting............................................... 19 Using Speaker Mounts/Brackets .................. 19 Using Rubber Stoppers with the Speakers ...................................... 19 Enjoying the Listening Modes Using the Listening Modes....................... 40 Selecting Listening Modes............................40 Connecting Antenna ..................................20 Connecting the Indoor FM Antenna ............. 20 Connecting the AM Loop Antenna ............... 20 Connecting an Outdoor FM Antenna............ 21 Connecting an Outdoor AM Antenna ........... 21 Advanced Operation Adjusting the Listening Modes ................ 44 Using the Audio Adjust Functions.................44 Using the Late Night Function (Dolby Digital only) .....................................45 Using the CinemaFILTER.............................45 Connecting Your Components .................22 About AV Connections ................................. 22 Connecting Both Audio & Video ................... 23 Which Connections Should I Use?............... 23 Connecting a TV or Projector ....................... 24 Connecting a DVD player............................. 25 Connecting a VCR or DVD Recorder for Playback ............................................... 26 Connecting a VCR or DVD Recorder for Recording ............................................. 27 Connecting a Camcorder, Games Console, or Other Device........................... 27 Connecting a Satellite, Cable, Set-top box, or Other Video Source........... 28 Connecting a CD Player or Turntable .......... 29 Connecting a Cassette, CDR, MiniDisc, or DAT Recorder........................................ 30 Connecting the Power Cord of Another Component................................... 30 Connecting Onkyo Components ........... 31 Connecting the Power Cord ......................... 31 Advanced Setup ........................................ 46 Advanced Speaker Settings .........................46 Digital Input Signal Formats .........................50 Recording................................................... 51 Recording the Input Source ..........................51 Recording from Different AV Sources ..........51 Troubleshooting ........................................ 52 Power ...........................................................52 Audio ............................................................52 Video ............................................................53 Tuner ............................................................53 Remote Controller ........................................53 Recording .....................................................54 Others ...........................................................54 Specification .............................................. 54 Turning On & First Time Setup Turning On..................................................32 Turning On the AV Receiver ........................ 32 First Time Setup .........................................33 Assigning Digital Inputs to Input Sources ..... 33 Changing the TAPE/MD/CDR Display ......... 33 5 Supplied Accessories Make sure you have the following accessories: HT-R430 Surround speakers (SKM-330S L/R) HT-R430 Surround Back speaker (SKB-330) Remote controller & two batteries (AA/R6) Subwoofer (SKW-420) Indoor FM antenna (Connector type varies from country to country.) (Red) (White) Speaker cable for front speakers 15 ft. (4.5 m) AM loop antenna (Green) Speaker cable for center speaker 10 ft. (3 m) Power-plug adapter Only supplied in certain countries. Use this adapter if your AC outlet does not match with the plug on the AV receiver's power cord. (Adapter varies from country to country.) (Blue) (Gray) (Brown) Speaker cables for surround speakers 30 ft. (9 m) HTP-430 RCA cable for subwoofer connection Front speakers (SKF-330F L/R) Rubber stoppers [24] * In catalogs and on packaging, the letter at the end of the product name indicates the color. Specifications and operation are the same regardless of color. Center speaker (SKC-330C) 6 Before Using the AV receiver Installing the Batteries Using the Remote Controller To use the remote controller, point it at the AV receiver's remote control sensor, as shown below. Remote control sensor AV receiver STANDBY indicator 1 To open the battery compartment, press the small hollow and slide open the cover. 2 Insert the two supplied batteries (AA/R6) in accordance with the polarity diagram inside the battery compartment. Approx. 16 ft. (5 m) 3 Slide the cover shut. Notes: · The remote controller may not work reliably if the AV receiver is subjected to bright light, such as direct sunlight or inverter-type fluorescent lights. Keep this in mind when installing. · If another remote controller of the same type is used in the same room, or the AV receiver is installed close to equipment that uses infrared rays, the remote controller may not work reliably. · Don't put anything, such as a book, on the remote controller, because the buttons may be pressed inadvertently, thereby draining the batteries. · The remote controller may not work reliably if the AV receiver is installed in a rack behind colored glass doors. Keep this in mind when installing. · The remote controller will not work if there's an obstacle between it and the AV receiver's remote control sensor. Notes: · The batteries should last for about six months, although this will vary with usage. · If the remote controller doesn't work reliably, try replacing the batteries. · Don't mix new and old batteries or different types of batteries. · If you intend not to use the remote controller for a long time, remove the batteries to prevent damage from leakage or corrosion. · Expired batteries should be removed as soon as possible to prevent damage from leakage or corrosion. 7 Front & Rear Panels Front Panel 1 2 3 4 5 6 78 9J K L TUNING / PRESET M MASTER VOLUME STANDBY/ON ENTER STANDBY A SPEAKERS B TONE + STEREO LISTENING MODE DISPLAY DIGITAL INPUT DIMMER MEMORY TUNING MODE RETURN SETUP CLEAR PHONES MULTl CH DVD VIDEO 1/VCR VIDEO 2 VIDEO 3 TAPE TUNER CD NO P Q R S For detailed information, see the pages in parentheses. L Arrow/TUNING/PRESET & ENTER buttons When the AM or FM input source is selected, the TUNING [ ] [ ] buttons are used to tune the tuner, and the PRESET [ ] [ ] buttons are used to select radio presets (see page 37). When the setup menus are used, they work as arrow buttons and are used to select and set items. The ENTER button is also used with the setup menus. A STANDBY/ON button (32) This button is used to set the AV receiver to On or Standby. B STANDBY indicator (32) This indicator lights up when the AV receiver is in Standby mode, and it flashes while a signal is being received from the remote controller. C Remote-control sensor (7) This sensor receives control signals from the remote controller. M MASTER VOLUME control (34) This control is used to adjust the volume of the AV receiver to MIN, 1 through 79, or MAX D STEREO button (40) This button is used to select the Stereo listening mode. N PHONES jack (39) This 1/4-inch phone jack is for connecting a standard pair of stereo headphones for private listening. E LISTENING MODE [ ]/[ ] buttons (40) These buttons are used to select the listening modes. O SPEAKER A & B buttons (34) These buttons are used to turn speaker sets A and B on or off. F Display See "Display" on page 9. P TONE, [­] & [+] buttons (38) These buttons are used to adjust the bass and treble. G DISPLAY button (35) This button is used to display various information about the currently selected input source. Q Input selector buttons (34) These buttons are used to select from the following input sources: MULTI CH, DVD, VIDEO 1/VCR, VIDEO 2, VIDEO 3, TAPE, TUNER, or CD. The [MULTI CH] button selects the DVD analog multichannel input. H DIGITAL INPUT button (33) This button is used to assign the digital inputs and to specify the format of digital input signals. I DIMMER button (38) This button is used to adjust the display brightness. R RETURN button This button is used to return to the previously displayed setup menu. J MEMORY button (37) This button is used when storing or deleting radio presets. S SETUP button This button is used to access various settings. K TUNING MODE button (36) This button is used to select the Auto or Manual tuning mode. 8 Front & Rear Panels--Continued Display 1 2 3 4 5 For detailed information, see the pages in parentheses. 6 5 SLEEP indicator (39) This indicator lights up when the Sleep function has been set. 1 A & B speaker indicators (34) Indicator A lights up when speaker set A is on. Indicator B lights up when speaker set B is on. 6 Message area This area of the display shows various information about the currently selected source. 2 MUTING indicator (38) This indicator flashes when the AV receiver is muted. 3 Source/listening mode indicators (42) These indicators show the currently selected listening mode and digital audio format. 4 Tuning indicators (36) TUNED (36): This indicator lights up when the AV receiver is tuned to a radio station. AUTO (36): This indicator lights up when Auto Tuning is selected and disappears when Manual Tuning is selected. MEMORY (37): This indicator lights up when presetting radio stations. FM STEREO (36): This indicator lights up when the AV receiver is tuned to a stereo FM station. 9 Front & Rear Panels--Continued Rear Panel 1 B 3 4 5 6 789 J K L M N O A DIGITAL IN OPTICAL & COAXIAL These optical and coaxial jacks can be used to connect a CD or DVD player and other components with digital audio outputs. jacks can be used to connect a VCR. The VIDEO 2 IN jack can be used to connect another video source (e.g., cable TV, satellite TV, or a set-top-box). I CD IN These analog inputs can be used to connect a CD player with analog outputs. B AM ANTENNA These push terminals are for connecting an AM antenna. J TAPE IN/OUT These analog inputs and outputs can be used to connect a cassette recorder, MiniDisc recorder, or other recorder with analog inputs and outputs. C FM ANTENNA This jack is for connecting an FM antenna. D VIDEO MONITOR OUT This composite video jack can be connected to a composite video input on your TV or projector. K S VIDEO MONITOR OUT This S-Video jack can be connected to an S-Video input on your TV or projector. E FRONT SPEAKERS B These push terminals are for connecting speaker set B. L VIDEO 1 IN/OUT, VIDEO 2 IN & VIDEO 3 IN The VIDEO 1 IN/OUT jacks can be used to connect a VCR. The VIDEO 2 IN and VIDEO 3 IN jacks can be used to connect other video sources (e.g., cable TV, satellite TV, or a set-top-box). F FRONT SPEAKERS A, SURROUND SPEAKERS, CENTER SPEAKER & SURROUND BACK SPEAKER These push terminals are for connecting speaker set A. M DVD IN The FRONT, SURROUND, CENTER, and SUBWOOFER jacks can be used to connect a component with an analog multichannel audio output, such as a DVD player with a 5.1-channel analog output. The composite video input can be connected to the composite video output on a DVD player. G This (Remote Interactive) jack can be connected to the jack on another Onkyo component. The AV receiver's remote controller can then be used to control that component. To use , you must make an analog audio connection (RCA) between the AV receiver and the other component, even if they are connected digitally. Note: can only be used with Onkyo components. N SUBWOOFER PRE OUT A powered subwoofer can be connected here. O AC OUTLET This switched AC outlet can be used to supply power to another component. The connector type depends on the country in which you purchased your AV receiver. See pages 17­31 for connection information. H S VIDEO DVD IN, VIDEO 1 IN/OUT & VIDEO 2 IN The DVD IN jack can be connected to an S-Video output on a DVD player. The VIDEO 1 IN/OUT 10 Speaker Package Front, Center, Surround, & Subwoofer speakers (SKF-330F, SKC-330C, SKM-330S, SKB-330, SKW-420) Rear SKF-330F SKM-330S SKB-330 A Speaker terminals These push terminals are for connecting the speaker to the HT-R430 with the supplied speaker cables. The supplied speaker cables are color-coded for easy identification. Simply connect each cable to the same-colored positive speaker terminal. 2 B Keyhole slots These keyhole slots can be used to wall-mount the speaker. See page 19 for mounting instructions. C Speaker mount/bracket inserts These threaded inserts can be used to attach the speaker to a speaker mount or bracket. See page 19 for mounting instructions. 3 2 SKC-330C 1 2 Note: Use commercially available machine screws to attach the speaker to a speaker mount or bracket. North American models require 1/4-inch screws. Other models require M5 (5 mm) screws. D OUTPUT LEVEL control This control is used to adjust the volume of the subwoofer. E STANDBY/ON indicator Red: Subwoofer in standby mode Green: Subwoofer on With the Auto Standby function, the SKW-420 automatically turns on when an input signal is detected in Standby mode. When there's no input signal for about 20 minutes, the SKW-420 automatically enters Standby mode. 3 SKW-420 1 F POWER switch (Not North American model) To turn on the SKW-420, set the POWER switch to the ON position (the indicator light up). To turn off the SKW-420, set the POWER switch to the OFF position (the indicator goes out). OUTPUT LEVEL LINE INPUT G LINE INPUT This RCA input should be connected to the SUBWOOFER PREOUT on your HT-R430 AV receiver, amp, or other receiver with supplied RCA cable. Note: The Auto Standby function turns the subwoofer on when the input signal exceeds a certain level. If the Auto Standby function does not work reliably, try slightly increasing or decreasing the subwoofer output level on your receiver or amp (see page 47). MIN MAX RED : STANDBY GREEN : ON 45 67 To AC outlet 11 Remote Controller How to Use the Remote Controller Including the AV receiver, the remote controller can be used to control up to six different components. The remote controller has a specific operating mode for use with each type of component. Modes are selected by using the five REMOTE MODE buttons. RECEIVER/TAPE Mode In RECEIVER/TAPE mode, you can control the AV receiver and an Onkyo cassette recorder connected via . DVD, CD, MD, & CDR Modes With these modes, you can control an Onkyo DVD player and CD/MD/CDR player/recorder. DVD RECEIVER Mode RECEIVER mode is used to control the AV receiver. To set the remote controller to RECEIVER mode, press the [RECEIVER] REMOTE MODE button. A ON STANDBY REMOTE MODE RECEIVER RECEIVER TAPE/AMP B C D 1 V1 DVD INPUT SELECTOR 2 V2 3 V3 CD 4 7 5 MULTI CH 6 DVD MD M N 8 TUNER 9 CD CDR CD TAPE +10 MD 0 DIMMER CLR SLEEP E F --/--- CDR DISC CH VOL O P TOP MENU MENU 1 2 Use the REMOTE MODE buttons to select a mode. Use the buttons supported by that mode to control the component. RECEIVER mode: see page 12 DVD mode: see page 14 CD/MD/CDR mode: see page 15 TAPE mode: see page 16 G SP A / B MUTING H I RETURN ENTER Q SETUP Note: Some of the remote controller operations described in this manual may not work as expected with other components. J K L LISTENING MODE STEREO SURROUND AUDIO SUBTITLE RANDOM REPEAT TEST TONE CH SEL PLAY MODE DISPLAY OR-EQ L NIGHT CINE FLTR LEVELLEVEL+ R S T RC-606S 12 Remote Controller--Continued For detailed information, see the pages in parentheses. O VOL [ ]/[ ] button (34) This button can be used to adjust the volume of the AV receiver regardless of the currently selected remote controller mode. A STANDBY button (32) This button is used to set the AV receiver to Standby. B ON button (32) This button is used to turn on the AV receiver. C INPUT SELECTOR buttons (34) These buttons are used to select the input sources. P MUTING button (38) This button is used to mute the AV receiver. Q SETUP button This button is used to access various settings. R CINE FLTR button (45) This button is used to set the CinemaFILTER function. D MULTI CH button (35) This button is used to select the multichannel DVD input. S L NIGHT button (45) This button is used to set the Late Night function. E DIMMER button (38) This button is used to adjust the display brightness. F CH +/­ button (37) This button is used to select radio presets. G SP A/B button (34) This button is used to turn speaker sets A and B on or off. T OR-EQ button (38) This button is used to turn on the OptiResponse equalizer, which optimizes performance when the HT-R430 is used with the speakers included in the HTP-430 Home Theater Speaker Package. When the OptiResponse equalizer is on, you can enjoy a powerful sound with movies or music with small volume. H Arrow [ ]/[ ]/[ ]/[ ] & ENTER buttons These buttons are used to select and adjust settings. I RETURN button This button is used to return to the previous display when changing settings. J LISTENING MODE buttons (40) These buttons can be used to select listening modes regardless of the currently selected remote controller mode. STEREO button This button selects the Stereo listening mode. SURROUND button This button selects the Dolby and DTS listening modes. [ ]/[ ] buttons These buttons can be used to select any of the available listening modes. K TEST TONE, CH SEL, LEVEL- & LEVEL+ buttons (32) These buttons are used to adjust the level of each speaker. L DISPLAY button (35) This button is used to display various information about the currently selected input source. M REMOTE MODE buttons (12) These buttons are used to select the remote controller modes. When you press a button on the remote controller, the REMOTE MODE button for the currently selected mode lights up. N SLEEP button (39) This button is used to set the Sleep function. 13 Remote Controller--Continued DVD Mode To set the remote controller to DVD mode, press the [DVD] REMOTE MODE button. Before selecting DVD mode and starting playback, you should press the [RECEIVER] mode button followed by the [DVD] INPUT SELECTOR button to select the DVD player as the input source. A STANDBY button This button sets the DVD player to Standby. B ON button This button is used to turn on the DVD player. C Number buttons These buttons are used to enter title, chapter, and track numbers and to enter times for locating specific points in time. D DISC +/­ button This button selects discs on a DVD changer. E TOP MENU button This button is used to select a DVD's top menu. F Arrow [ ]/[ ]/[ ]/[ ] & ENTER buttons A ON STANDBY REMOTE MODE These buttons are used to navigate DVD menus and the DVD player's onscreen setup menus. RECEIVER TAPE/AMP B C 1 V1 DVD DVD G RETURN button This button is used to exit the DVD player's onscreen setup menu and to restart menu playback. INPUT SELECTOR 2 V2 3 V3 CD H Playback buttons MD CDR 4 7 TAPE 5 MULTI CH 6 DVD 8 TUNER 9 CD From left to right: Pause, Play, Stop, Fast Reverse, Fast Forward, Previous, and Next. I SUBTITLE button +10 --/--- 0 DIMMER CLR SLEEP L VOL This button is used to select subtitles. J AUDIO button This button selects foreign language soundtracks and audio formats (e.g., Dolby Digital or DTS). D TOP MENU DISC CH K DISPLAY button MENU E SP A / B MUTING M ENTER F G RETURN This button is used to display information about the current disc, title, chapter, or track on the DVD player's display, including the elapsed time, remaining time, total time, and so on. N SETUP L CLR button This button is used to cancel functions and to clear entered numbers. H LISTENING MODE STEREO SURROUND M MENU button This button is used to display a DVD's menu. N SETUP button I J K