Model 200 M-Block Power Amplifier ® Owner's Manual Owner's Manual Warnings Please Read First Installation Location To assure proper operation and to avoid the potential for safety hazards, place the unit on a firm and level surface capable of supporting 20 pounds or more. When placing the amplifier on a shelf, be certain that the shelf and any mounting hardware can support the weight of the amplifier and any additional items in the equipment rack, or on the shelf. When positioning the amplifier in its final location, make certain that it has adequate ventilation on all sides, as well as on the top and bottom. In particular, it is a good idea to provide at least two or three inches of room above the amplifier for air circulation. DO NOT place CDs, DVDs, videotapes, owner's manuals, or other paper on top of, or beneath, the unit, or in-between multiple amplifiers in a stack. This will block airflow, causing heat build-up, degraded performance, and may create a possible fire hazard. If the unit is to be enclosed in a cabinet or rack, make certain there is adequate air circulation. Sufficient ventilation should be provided so that hot air may exit, and cool air may enter the cabinet. In some instances, a small cooling fan may be required to insure adequate airflow through the cabinet. If you are in doubt as to the ventilation requirements for your specific installation, please contact us. Also, do not place the amplifier directly on a carpeted surface, as this will inhibit airflow underneath as well as create a potential fire hazard. Avoid installation in humid locations, in extremely hot or cold locations, or in areas that are exposed to direct sunlight or space heating equipment. Loudspeaker Ratings Your Outlaw Power Amplifier has adequate power to drive most loudspeakers without producing any distortion. Most modern speakers are rated at four to eight ohms nominal impedance, but within some frequency ranges, the impedance may drop to two ohms. The Outlaw is designed with ample power reserves to protect you from experiencing any problems at these low impeadances unless you demand excessively high volume levels. Due to the high power output capability of your power amplifier, it is important that it not be used with speakers not capable of handling the amplifier's power output. Before using the amplifier for the first time, make certain that your speakers are capable of handling its rated power output, at the impedance rating of your speakers. Outlaw Audio is not responsible for damage to any speaker system or other component that is caused by using products whose power rating is lower than that of the amplifier. Do Not Open The Cabinet There are no user serviceable components inside this product. Opening the cabinet may present a shock hazard, and any modification to the product will void your guarantee. If water or any metal object, such as a paper clip, coin or a staple, accidentally falls inside the unit, disconnect it from the AC power source immediately, and contact Outlaw Audio for further instructions. CAUTION: To reduce the risk of electric shock, do not remove the cover (or back). No user serviceable parts inside. Refer to qualified personnel. WARNING: To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture. The lightning flash with arrowhead, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electrical shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating maintenance (servicing) instructions in the literature accompanying the appliance. Precautions Verify The Line Voltage Your new amplifier has been factory configured for 120 (+/- 3%) volt AC lines. Connecting the amplifier to a line voltage other than that for which it is intended can create a safety and fire hazard, and may damage the amplifier. If you have any questions about the voltage requirements for your specific model, or about the line voltage in your area, contact Outlaw Audio before plugging the unit into a wall outlet. Verify AC Circuit Capacity The high power output of your Outlaw amplifier may require heavy power draw under full load conditions. To insure proper performance, and to avoid potential safety hazards, we recommend that it be connected to a minimum 20 Amp capacity circuit. Connecting multiple amplifiers to the same circuit, or connecting it to a circuit used by other heavy power devices, such as air conditioners, may cause circuit breakers to trip. NOTE: It is always a good idea to avoid using any audio or video equipment on the same AC circuit as equipment with motors, such as air conditioners or refrigerators. This will lessen the possibility of power variation and electrical start-up noise affecting your sound system. Extension Cords and Power Strips We do not recommend that extension cords be used with this product unless they are of sufficient gauge to pass the necessary current during full load conditions. Most inexpensive extension cords are not capable of such high-current loads. Similarly, should you use a power strip, surge protector or any type of AC power line conditioning equipment, make certain that it is also able to handle the high current loads this product will produce. Handle the AC Power Cord Gently When disconnecting the power cord from an AC outlet, always pull the plug, never pull the cord. If you do not intend to use the amplifier for any considerable length of time, disconnect the plug from the AC outlet. If the power cord is replaced, make certain that it is of similar gauge. As with all electrical devices, do not run power cords under rugs or carpets or place heavy objects on them. Damaged power cords should be replaced immediately with cords meeting factory specifications. Wiring Cables that are run inside of walls should have the appropriate markings to indicate complaince with, and listing by the UL , CSA or other standards required by the UL, CSA, NEC or your local building. Questions about cables inside of walls should be referred to a qualified customer installer, or a licensed electrician or low-voltage contractor. IMPORTANT SAFETY NOTE Before connecting a new component such as power amplifier to your audio or home theater system it is always good practice to make certain that all components are turned off, and preferably unplugged from their AC power source. Many modern electronics products feature automatic turn-on circuits that may be activated during an installation, causing the potential for damage to electronic components and/or speakers. Such damage is not covered by product warranties and Outlaw Audio specifically disclaims responsibility for any such damage. For Future Reference Record your amplifier's serial number and date of purchase here. It is found on the back panel. Serial Number Date of Purchase 2 Outlaw Audio Owner's Manual Unpacking Table of Contents 3 3 3 4 5 5 5 Model 200 M-Block Power Amplifier Features Unpacking Front Panel and Rear Panel Installation and Configuration Model 200 M-Block Power Amplifier Welcome to the Outlaw Family! With your purchase of a Model 200 M-Block Amplifier you have become part of a unique, worldwide community of audiophiles and home theater enthusiasts. With one or more Model 200 amplifiers you have the option to add power and flexibility to your system for a wide range of applications, such as; adding rear surround channels to a new 7.1 system, powering passive subwoofers, enabling bi-amp speaker configurations, powering multi-zone/multi-room speakers and much more. The Model 200 is compact, yet powerful, delivering 200 watts at eight ohms (20Hz­20KHz, >0.05%THD). Thanks to a unique circuit design and a heavyduty power supply with a horizontally oriented torroidal transformer, the Model 200 operates without a fan despite the deep power reserves. Since the Model 200 will often be used in multiple unit systems, a variety of power control options are provided. In addition to a standard power on/off switch, the Model 200 may be operated from the external trigger control of compatible products such as the Outlaw Model 950. Both in and out trigger jacks are provided so that the control signal may be cascaded. For systems where an external trigger is not available, the Model 200's music sense circuitry is available for automatic turn-on whenever an audio signal is present. In order to fully enjoy the performance of your amplifier, please take a few minutes to read this owner's manual. It contains important information that will help you to make certain that the amplifier is properly configured for operation with the rest of the equipment in your system. Once again, welcome to the Outlaw family! 6 7 7 7 8 8 8 8 8 8 8 9 9 Power Control Connections Speaker Wire Connections Model 200 Connection Diagram Audio Signal Connections AC Power Connection Operation Care and Maintenance Cleaning Troubleshooting Guide Protection Circuitry Fuse Replacement Outlaw Service Information Troubleshooting A Few Words About Hum and Noise Potential Ground Loops in a Complex A/V System 10 Specifications 11 The Outlaw Audio 30-Day Satisfaction Guarantee 11 Outlaw Audio Limited Warranty Features High-power M-Block amplifier Unique dual-topology circuit design Music Sense circuitry and low voltage trigger connection for automatic turn-on Five-way binding posts accommodate large gauge speaker cable Fan-free convection cooling Efficient power supply with torroidal transformer Removable IEC power cord Unpacking The carton and packing materials used in shipping your new amplifier were specially designed to cushion it from the shocks and vibration of shipping. We strongly suggest that you save the carton and packing materials to use if you move, or if the unit ever needs to be shipped back to us for any reason. To minimize the size of the carton in storage, you may wish to flatten it by carefully opening the top and bottom flaps and folding the carton flat. Other cardboard inserts may be stored in the same manner. Packing materials that cannot be collapsed should be saved along with the carton in a plastic bag. Model 200 M-Block Power Amplifier 3 The contents of this manual are Copyright © 2003 by Outlaw Audio, LLC and may not be duplicated or reproduced by any means, whether physical, electronic or otherwise without prior written consent from Outlaw Audio. Specifications are those in effect at the time of printing. Outlaw Audio reserves the right to change specifications or designs at any time without notice or liability to modify or upgrade units previously sold. Owner's Manual Front and Rear Panel Front Panel and Rear Panel A B C D E F G H I J A The front panel LED indicator has three modes: Amber: Indicates that the Model 200 is connected to an AC power source and the rear-panel Main Power switch is turned on. When the indicator is amber, the unit is in the Standby mode and is ready to turn on when a control signal is received at the trigger jack or from the music sense circuitry. Green: Indicates that the Model 200 is on and operational. Red: Indicates that the Model 200 is in the Protect mode. If the LED is red, Jack of an additional Model 200. Note, however, that connecting more than two Model 200s to a single source controller may overload the system and is not recommended. If you wish to automatically turn on more than two Model 200 units, we recommend the use of either the music sense circuitry or an externally powered relay controller. Contact Outlaw Audio Customer Service for more information on using the Model 200 in multiple unit systems to avoid damage to your processor, receiver or controller. E you should turn the unit off and then check for the source of the condition that caused the overload. This may be a shorted speaker lead or other similar condition. In the event of repeated appearance of the red LED you may have a chronic system failure with either the Model 200 or another component in your system. In this case disconnect the Model 200 from AC power and the rest of your system and consult Outlaw Audio's Customer Service Department for assistance. B Trigger Mode Switch This three-position switch determines the method by which the Model 200 will be placed in the active, or ON, position: When the switch is in the far right position, under the word "ON," the unit will be turned on when the Main Power Switch is turned on. When the switch is in the middle position, under the word "MUSIC," the unit will automatically turn on when an audio signal is present at the Input Jacks. The unit will automatically turn off when the signal is no longer present. When the s ...