OWNER'S MANUAL 51CM CORDLESS REMOTE COLOUR TELEVISION MODEL: 5130G Type Tested Electrical Safety AS/NZS 3250 Lic 4164 Standards Australia APP No: N15959 PALSONIC CORPORATION PTY LTD 1 JOYNTON AVENUE WATERLOO NSW 2017 AUSTRALIA TEL: (02) 9313 7111 FAX: (02) 9313 7555 www.palsonic.com.au PALSONIC CUSTOMER SERVICE TELEPHONE AUSTRALIA: 1300 657 888 Contents Congratulations on your purchase of this Palsonic colour television receiver. We recommend that you thoroughly read this manual before use to fully enjoy the many functions and excellent effects of this receiver. Retain this manual in an easily accessible location for future reference. Note: Screen displays and illustrations in this manual may differ from the actual ones for better visibility. CONTENTS Features .......................................................................................................................... Important Safety Cautions ............................................................................................... Identification of Controls .................................................................................................. Installation ....................................................................................................................... Menu Introduction ............................................................................................................ Turning On/Off ................................................................................................................. Select Input Signal ........................................................................................................... Tuning In .......................................................................................................................... Channel Selection ........................................................................................................... Adjusting Picture .............................................................................................................. Sound Control .................................................................................................................. Clock Setting.................................................................................................................... System Setting................................................................................................................. Safe Mode ....................................................................................................................... Troubleshooting Guide .................................................................................................... Specifications .................................................................................................................. 1 2 4 8 10 12 13 14 17 18 19 20 22 24 27 28 Features Hyperband Intellectualised I 2 C bus control 255 preset channels Automatic channel preset Full function remote control AV input and output terminals Clock/Game/Calendar Digital AFT technology Four picture modes ON timer/OFF timer Channel exchange Safe mode 1 Important Safety Cautions 1 When any unusual situation occurs, turn off the power supply at once and remove the plug from the wall outlet. Contact a qualified service department in your local area. 2 Do not expose the TV set to rain or excessive moisture. Avoid using the set in very warm or damp places and never use it in a bathroom. 3 When cleaning dust off the picture tube disconnect the power first. You can wipe lightly with a piece of dry, clean and soft cloth. 4 Avoid exposing the set to direct sunlight and other sources of heat to prevent damage to the cabinet and components. 5 High voltage exists in this TV set. Do not remove the cover. 2 ! This TV set can operate on an AC power of 240V, 50Hz. You must not use a power supply of any other type. 6 Do not cover the ventilating hole in the cabinet Keep a space of more than 5 cm from the walls to the TV set to ensure adequate ventilation. 7 If the power cord or the plug is damaged contact a qualified service department for service. 8 When the TV set is to be left unattended for a long period of time, turn off the power supply and remove the plug from the wall outlet. 9 Don't try to push anything into the cabinet or place any vessel with water on the set. 10 Don't overload wall outlets; extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock. 3 Identification of Controls Front POWER SWITCH REMOTE SENSOR INDICATOR INDICATOR 1 2 1. 3 4 5 6 7 Earphone Jack AV/TV input terminals (VIDEO, AUDIO L, R). 2. AV/TV button: Video input select. 3. MENU button: To enter into menu operation. 4. VOL- button: volume down adjust; menu item adjust 5. VOL+ button: volume up adjust; menu item adjust. 6. CH- button: channel down select; menu item select. 7. CH+ button: channel up select; menu item select. 4 Back 4 1 3 2 1. Antenna input 2. S-VIDEO input 3. AV input (VIDEO, AUDIO L/MONO, R) 4. AV output (VIDEO, AUDIO L/MONO, R) 5 Identification of Controls (continued) Remote Controller Power on/standby Direct channel selector Previous channel Digit select Break Calendar Help in menu operations Channel up Volume down Picture mode select Playing game Undo operation in game To enter MENU operation Volume up Channel down TV/VIDEO input select On-Screen call Sleep timer Sound mute Menu control ! Notes: In most cases, the function CH+/- buttons are equal to the function of VOL+/- buttons are equal to the buttons. / buttons, and the 6 Installing batteries 1 Effective range of the Remote Open the battery cover. 2 300 300 5m Install two "AAA" batteries matching the +/- polarities of the battery to the +/marks inside the battery compartment. 3 Replace the battery cover. ! Notes: When there is an obstacle between the TV and the transmitter, the transmitter may not operate. When direct sunlight, and incandescent lamp, fluorescent lamp or any other strong light shines on the REMOTE SENSOR of the TV the remote operation may be unstable. ! Notes: The battery life should be about one year under normal use. Do not try to recharge batteries not intended to be recharged. Use only the size and type of batteries specified. Do not mix different types of batteries together or old batteries with fresh ones. When the remote control will not be used for a long period of time or when the batteries are worn out, remove the batteries. Do not throw the batteries into a fire. Dispose of used batteries in the specified manner. Do not drop, dampen or disassemble the remote control. 7 Installation INSTALL the unit in a room where direct light will not fall upon the screen. Total darkness or a reflection on the picture screen may cause eyestrain. Soft and indirect lighting is recommended for comfortable viewing. Antenna installation Optimum reception of colour requires a good signal and will generally mean that an outdoor aerial must be used. The exact type and position of the aerial will depend upon your particular area. ! Notes: It is recommended that the 75-ohm coaxial cable be used to eliminate interference and noise which may occur due to radio wave conditions. The aerial cable should not be bundled with the power cord and the like. 8 Connect to video and audio equipment This TV set provides AV input terminals for your convenient connection to VTR, DVD or video camera to enjoy the high quality picture. Please refer to the owner's manual of the equipment to be connected as well. Important notes on the AV input terminals Please do not connect and use the side and rear input terminals at the same time. You can connect a stereo system to the AV output terminals on the set to enjoy a high quality sound from the stereo system. The AV output terminals output video and audio signals being displayed on the screen. TV SET SIDE To audio outputs VIDEO EQUIPMENT To video outputs To earphone jack You can also use the AV terminals on the TV set rear as follows. ! Notes: Please do not connect and use the S-VIDEO and VIDEO terminals at the same time. Please note that the rear audio input terminals are stereo while the side are mono. 9 Menu Introduction The selected item displays in yellow. In MENU operations, the CH+/- (or ) buttons are used to select item upwards or downwards; the VOL+/- (or / ) buttons are used to adjust or confirm selected item. Join to page 11 If the marginal item is selec Help information for menu To adjust the picture's contr Normal Picture Press MENU button once To adjust the picture's colour To adjust the picture's brigh To adjust the picture's sharp To adjust the picture's skin Press MENU button Press MENU button twice To select OSD language. To set blue background. To enter calendar. To play game. To limit some functions. Press MENU button Press MENU button three times To set sleep timer. To set the current time. To set OFF timer. To set ON timer. To set alarm channel when Press MENU button Press MENU button four times To set the colour system. To set the sound system. To set channel skip. To set target channel that e To exchange programs in c To set current channel num To select the band for curre To fine tune manually. To search program manuall To search program automat 10 Join to page 11 ! Notes: In most cases, the function of CH+/- buttons are equal to the buttons; and the function of VOL+/- buttons are equal to the / buttons. Join to page 10 ted and there are some items that are not displayed yet, the perations (Press HELP button to display/cancel this help bar). ast. tness. ness. colour. (This item is available only in NTSC) or symbol twinkles. ! The Picture menu will be shielded if you set the AdjLimit item to Off in SafeMode. To set SafeMode function to On or Off. The following item are available only when the SafeMode is set to On. To set the maximum volume in SafeMode. To set the maximum channel in SafeMode. To turn on/off the Picture menu in SafeMode. To turn on/off the Program menu in SafeMode. To select input mode when you turn on by Power Switch. To set whether the set auto search when you turn on by Power Switch. This function will be turned off automatically after it is fulfilled successfully. To set whether the set auto demonstrate when you turn on by Power Switch. This function will be be turned off automatically after it is fulfilled successfully. To set a new password. the T V set auto turns on by TimeOn function. ! The Program menu will be shielded if you set the Search item to Off in SafeMode. changes its program with current channel's program. urrent channel and target channel. ber. nt channel. y, it stops if a certain program is found. ically. Join to page 10 11 Turning on/off Turning on 1. Press the Power Switch on the TV set. If no picture appears, then the TV set is in STANDBY mode. Now please follow step 2. 2. In STANDBY mode, press the button on the remote controller and the TV set is turned on. 1 3 3. In STANDBY mode, you can also press the AV/TV button on the set to turn on. ! Notes: 2 If there is no input signal, then a blueground appears. After 15 minutes, the set auto goes to STANDBY. Turning off 1. Press the Power Switch on the TV set if you want to cut off the power completely. 2. If you want to turn off the TV set temporarily, press the button on the remote controller. ! Notes: There are three kinds of Auto-Power-Off function: A. When there is no input signal for 15 minutes. B. Sleep-timer function. C. Off-timer function. However, in the mode of Game or Break, the function of Auto-Power-Off if no signal is received will be ineffective. 12 Select Input Signal Select input signal 1. Press AV/TV button on the TV set or AV button on the remote control. When the set is in TV mode, press this button and the set goes to AV mode. Now you could watch video program from AV input terminals. If you want to switch to TV press AV button again or follow step 2, 3 or 4. 2. Press the digit buttons to switch back to TV mode. 3. Press CH+ or CH- button to switch back to TV mode. 4. Press button to switch back to TV mode. 1 3 2 4 5 Press DSP button, the set displays current input mode. The OSD disappears in about 5 seconds. SafeMode 18:09 18 Notes: 3 1 5 3 If the Timer item has been set, the current time also appears. If the SafeMode is turned on, the "SafeMode" also appears. 13 Tuning in 1. Press MENU button four times to display Program menu. 2. Press CH+/- button to select item. 3. Press VOL+/- button to confirm or adjust the selected item. Auto Search Enter the Program menu and select Auto item. Press VOL+ or VOL- button and the TV set starts Auto Channel Preset. All Active channels will be preset and stored into the memory automatically. After presetting, the TV will stop at the last channel program. During the process of Auto channel preset, pressing the MENU or CH+ ...