OWNER'S MANUAL 68CM CORDLESS REMOTE COLOUR TELEVISION MODEL: 6825G Type Tested Electrical Safety AS/NZS 3250 Lic 4166 Standards Australia APP No: N15899 PALSONIC CORPORATION PTY LTD 1 JOYNTON AVENUE WATERLOO NSW 2017 AUSTRALIA TEL:(02)9313 7111 FAX:(02)9313 7555 www.palsonic.com.au PALSONIC CUSTOMER SERVICE TELEPHONE AUSTRALIA:1300 657 888 Contents Contents Congratulations on your purchase of this Palsonic colour television receiver. We recommend that you thoroughly read this manual before use to fully enjoy the many functions and excellent effects of this receiver. Retain this manual in an easily accessible location for future reference. Note: Screen displays and illustrations in this manual may differ from the actual ones for better visibility. CONTENTS Features .................................................................................................................. Important Safety Cautions ....................................................................................... Identification of Controls .......................................................................................... Installation ............................................................................................................... Turning On/Off ......................................................................................................... Select Input Signal .................................................................................................. Tuning In ................................................................................................................. Channel Selection ................................................................................................... Adjusting Picture ..................................................................................................... Sound Control ......................................................................................................... Timer Setting............................................................................................................ System Setting......................................................................................................... Other FunctionsS .................................................................................................... Troubleshooting Guide ............................................................................................ Specifications .......................................................................................................... 1 2 4 8 11 12 13 16 17 18 20 22 24 27 28 Features Features Hyperband Intellectualized I C bus control 256 preset channels Full function remote control AV input & output terminals, DVD input terminals Intellectualized remote controller caller Automatic channel preset Clock/Game/Calendar ON timer/OFF timer Channel Exchange Selectable picture and selectable sound 2 1 Important Safety Cautions Safety Cautions 1 When any unusual situation occurs, turn off the power supply at once and remove the plug from the wall outlet. Contact a qualified service department in your local area. 2 Do not expose the TV set to rain or excessive moisture. Avoid using the set in very warm or damp places and never use it in a bathroom. 3 When cleaning dust off the picture tube disconnect the power first. You can wipe lightly with a piece of dry, clean and soft cloth. 4 Avoid exposing the set to direct sunlight and other sources of heat to prevent damage to the cabinet and components. 2 ! This TV set can operate on an AC power of 240V, 50HZ. You must not use a power supply of any other type. 5 High voltage exists in this TV set. Do not remove the cover 6 Do not cover the ventilating hole in the cabinet Keep a space of more than 5cm from the walls to the TV set to ensure adequate ventilation. 7 If the power cord or the plug is damaged contact a qualified service department for service. 8 When the TV set is to be left unattended for a long period of time, turn off the power supply and remove the plug from the wall outlet. 3 Identification of Controls Front 1. TV/VIDEO input select. 2. Volume up; menu item adjust. 3. Volume down; menu item adjust. 4. To enter menu operation. 5. Channel up; menu item select. 6. Channel down; menu item select. 7. To call remote controller. 8. AV3 inputs (VIDEO, AUDIO L/MONO, R) 4 Back 3 1 4 5 2 6 1. Antenna input. 2. DVD inputs (VIDEO: Y, C B , CR , AUDIO L/MONO, R). 3. AV 2 inputs (VIDEO, AUDIO L/MONO, R). 4. S-VIDEO input. 5. AV outputs (VIDEO, AUDIO L/MONO, R). 6. AV 1 inputs (VIDEO, AUDIO L/MONO, R). 5 Identification of Controls (continued) Remote Controller The switch of the remote controller caller Power on/standby Direct channel selector TV/VIDEO input select Colour and sound system select Volume up/dowm select; menu item adjust Channel edit To enter/exit game menu To mute the sound Program scanning Previous channel To enter menu operation Channel up/down select; menu item select Picture mode select To enter game/Serve as confirm button in GOBANG game Game controller Sleep timer Sound mode select On-screen call 6 Installing batteries 1 Effective range of the Remote Open the battery cover. 2 Install two "AAA" batteries matching the +/- polarities of the battery to the +/marks inside the battery compartment. 3 Replace the battery cover. ! Notes: When there is an obstacle between the TV and the transmitter, the transmitter may not operate. When direct sunlight, and incandescent lamp, fluorescent lamp or any other strong light shines on the REMOTE SENSOR of the TV the remote operation may be unstable. ! Notes: The battery life should be about one year under normal use. Do not try to recharge batteries not intended to be recharged. Use only the size and type of batteries specified. Do not mix different types of batteries together or old batteries with fresh ones. When the remote control will not be used for a long period of time or when the batteries are worn out, remove the batteries. Do not throw the batteries into a fire. Dispose of used batteries in the specified manner. Do not drop, dampen or disassemble the remote control. 7 Installation INSTALL the unit in a room where direct light will not fall upon the screen. Total darkness or a reflection on the picture screen may cause eyestrain. Soft and indirect lighting is recommended for comfortable viewing. Antenna installation Optimum reception of colour requires a good signal and will generally mean that an outdoor aerial must be used. The exact type and position of the aerial will depend upon your particular area. ! Notes: It is recommended that the 75-ohm coaxial cable be used to eliminate interference and noise which may occur due to radio wave conditions. The aerial cable should not be bundled with the power cord and the like. 8 This TV set provides 3 groups of AV input (including one group of DVD inputs) and 1 group of AV out puts for your convenient connection to VTR, DVD or video camera to enjoy the high quality picture. Please refer to the owner's manual of the equipment to be connected as well. Using AV Inputs ! Notes: In AV1 inputs, the S-VIDEO terminal is prior to the VIDEO1 terminal. When both S-VIDEO and video signals are input, the S-VIDEO signal is selected. To view a video sognal, disconnect the S-VIDEO connection. The AV2 inputs and the DVD inputs use the same audio terminals. When both DVD and video signal are input, the DVD inputs are prior to VIDEO2 terminal and DVD signal is selected. To view video signal, disconnect Y /CB /C R connection, 9 Installation (continued) Using DVD inputs Using AV outputs 10 Turning on/off Turning on 1 Press the Power Switch on the TV set. The TV set is in STANDBY and the Yellow indicator lights up. 2, 2 2 3 In STANDBY mode, press the button or 0-9 buttons on the remote controller and the TV set is turned on. In STANDBY mode, you can also press the VOL , CH or TV/AV button on the set to turn on. ! Notes: If there is no input signal, then a blueback appears. After 15 minutes, the set auto goes to STANDBY. Turning off 1 Press the Power Switch on the TV set if you want to cut off the power completely. 2 If you want to turn off the TV set temporarily, press the button on the remote controller. 11 Select Input Signal Watching AV program 1 To watch video program from AV input, PressTV/AV button repeatedly until you see the appropriate input indicator on the screen Video1 Video2 Video3 10 2 ! Notes: 1, 1 3 4 In AV1 inputs, the S-VIDEO terminal is prior to the VIDEO1 terminals. When both S-video and video signal are input, the Svideo signal is selected (the OSD is "S-VIDEO1"). To view a video signal, disconnect the S-VIDEO connection. The AV2 inputs and the DVD inputs use the same audio terminals. When both DVD and video signal are input, the DVD inputs are prior to VIDEO2 terminals and the DVD signal is selected (the OSD is "DVD"). To view a video signal, diconnect Y/CB /CR connection. Switching from AV to TV 1 3 Press TV/TV button repeatedly until the TV program appears. 2 Press digit buttons to switch back to TV mode. Press CH+ or CH- button to switch back to TV mode. button to switch back to TV mode. 4 Press 12 Tuning in To enter the SEARCH menu 1 2 2, 2 Press MENU button. Press VOL+ or VOL- button to select SEARCH icon. Press CH- button to disply the Serach menu. 3 Auto Search Please enter the SEARCH menu first 1 1 2 2 3 CH- button to 1 Press CH+ orMEMORY item. select AUTO 2 Press VOL+ button to start AUTO MEMORY. All active channels will be preset and stored into the memory automatically. After presetting, the TV will stop at the first channel program. ! Notes: During the process of AUTO MEMORY, pressing the VOL- button will stop the process and go to the first channel. 13 Tuning in (continued) Manual Search Please enter the SEARCH menu first Use MANUAL SEARCH function if desired channels cannot be preset or if you would like to preset channels to specific position numbers one by one 1 3 1,3 1,3 2,4 2,4 Press CH+ or CH- button to select POSITION item. 2 Press VOL+ or VOL- buttons to select a channel number (ranging from 000~255). Press CH+ or CH- button to select SEARCH item. 4 Press VOL+ or VOL- button to start program search manually. Pressing VOL+, the set searches towards higher frequency; Pressing VOL-, the set searches towaords lower frequency; The search stops when a program is located and this program will be stored in the specified position number. ! Notes: 1. You can use BAND selection to quicken search process if you know which band your desired progam locates in. The band switches amoung VHFL, VHFH and UHF. 2. Repeat the above steps if you want to store another program in other position numbers To skip an unnecessary channel 1 3 Press CH+ or CH- button to select POSITION item. or VOLselect 2 Press VOL+ example,button to 009. a channel number, for channel Press CH+ or CH- button to select SKIP item. 4 Press VOL+ or VOL- button to select ON. Now channel 9 will be skipped when you browse by CH+ or CH- button. To restore a skipped channel, please select channel by step 1, 2 then repeat step 3 and 4 and set SKIP item to OFF. 14 Fine tuning Please enter the SEARCH menu first Fine tuning is not necessary under normal conditions. However, in area of inferior broadcast conditions where adjustment is necessary for better picture and sound, use Fine tuning. 1 3 1,3 2,4 Press CH+ or CH- button to select POSITION item. or VOL2 Press VOL+ fine-tunebuttons to select a channel number you want to (for example, channel 99). Press CH+ or CH- button to select MFT item. or VOL- button till 4 Press and hold VOL+sound are obtained.the best possible picture and Calling the on-screen display You can call the on-screen display by pressing the DSP button on the remote controlle. The first press of the DSP button display the current state (if in TV mode, the current channel number will display) and the next press display the clock time. Press this button again to cancel the OSD. DSP 15 Channel Selection 1 Using 0-9 direct channel selector To select one-digit channel There are 3 ways for you to select an one-digit channel number, for example, channel 9 as follows. A B 2 Press "9" button 9-- After 2 seconds 9 Press "0" button 0-- Press "9" button 09- After 2 seconds 9 C Press "0" button 0-- Press "0" button 00- Press "9" button 9 To select two-digit channel 1, 1 3 4 There are 2 ways for you to select a two-digit channel number, for example, channel 19 as follows A B Press "1" button 1-- Press "9" button 19- After 2 seconds 19 Press "0" button 0-- Press "1" button 01- Press "9" button 19 To select three-digit channel To select a three-digit channel number, for example, channel 199, you just input the channel number on by one. Be sure that the period of two-press channel should be wi ...