Digital Super Hybrid System Please read this manual before connecting the Digital Super Hybrid System. DIGITAL SUPER HYBRID D1232 SYSTEM DIGITAL SUPER D816 HYBRID SYSTE M MODEL KX-TD816E / KX-TD1232E Panaso nic Panaso nic KX-TD816 KX-TD1232 Thank you for purchasing the Panasonic Model KX-TD816E/KX-TD1232E, Digital Super Hybrid System. System Components Model Service Unit Telephone KX-TD816E KX-TD1232E KX-T7420E KX-T7425E KX-T7431E KX-T7433E KX-T7436E KX-T7220E KX-T7230E KX-T7235E KX-T7250E KX-T7130E KX-T7020E KX-T7050E KX-T7440E KX-T7441E KX-T7240E KX-T7040E KX-TD170E KX-TD180E KX-TD181E*1 KX-TD182E*2 KX-TD190E KX-TD192E*1 KX-TD196E*1 KX-TD197E KX-TD198E*2 KX-TD199E*2 KX-TD280E KX-TD281E*1 KX-TD282E*2 KX-TD286E KX-TD290E KX-TD142 KX-TD144 KX-TD146 KX-T30865E KX-A46E Description Digital Super Hybrid System (Main Unit) Digital Super Hybrid System (Main Unit) Digital proprietary telephone Digital proprietary telephone Digital proprietary telephone with 1-line display Digital proprietary telephone with 3-line display Digital proprietary telephone with 6-line display Digital proprietary telephone Digital proprietary telephone with 2-line display Digital proprietary telephone with 6-line display Digital proprietary telephone Proprietary telephone with 1-line display Proprietary telephone Proprietary telephone Digital DSS Console Digital Attendant Console Digital DSS Console DSS Console 8-Station Line Unit 4-CO Line Unit 8-CO Line Card 4-CO Line Card Message Unit System Inter Connection Card (two cards with Connection Cable) Remote Card 9600bps Speed Remote Card 9600bps Speed Remote Unit Message Card 2-ISDN S0 Line Unit 4-ISDN S0 Line Card 2-ISDN S0 Line Card 6-ISDN S0 Line Unit Primary Rate Interface (PRI) ISDN Expansion Unit Cell Station Cell Station Interface Unit Doorphone Battery Adaptor Optional Equipment System Components Table Note In this Installation Manual, the suffix "E" of each model number is omitted. The Digital Super Hybrid System is abbreviated as "DSHS." The Digital Proprietary Telephone is abbreviated as "DPT." Other proprietary telephone (analogue type) is abbreviated as "APT." A Single Line Telephone is abbreviated as "SLT." 2 *1: Available for KX-TD1232 only. *2: Available for KX-TD816 only. Important Information FOR YOUR SAFETY PLEASE READ THE FOLLOWING TEXT CAREFULLY. This appliance is supplied with a moulded three pin mains plug for your safety and convenience. A 5 amp fuse is fitted in this plug. Should the fuse need to be replaced please ensure that the replacement fuse has a rating of 5 amps and that it is approved by ASTA or BSI to BS1362. Check for the ASTA mark or the BSI mark on the body of the fuse. If the plug contains a removable fuse cover you must ensure that it is refitted when the fuse is replaced. If you lose the fuse cover the plug must not be used until a replacement cover is obtained. A replacement fuse cover can be purchased from your local Panasonic Dealer. IF THE FITTED MOULDED PLUG IS UNSUITABLE FOR THE SOCKET OUTLET IN YOUR HOME THEN THE FUSE SHOULD BE REMOVED AND THE PLUG CUT OFF AND DISPOSED OF SAFELY. THERE IS A DANGER OF SEVERE ELECTRICAL SHOCK IF THE CUT OFF PLUG IS INSERTED INTO ANY 13 AMP SOCKET. If a new plug is to be fitted please observe the wiring code as shown below. If in any doubt please consult a qualified electrician. WARNING : THIS APPLIANCE MUST BE EARTHED. IMPORTANT : The wires in this mains leads are coloured in accordance with the following code: Green-and-yellow: Earth Blue: Neutral Brown: Live As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows. The wire which is coloured GREEN-AND-YELLOW must be connected to the terminal in the plug which is marked with the letter E or by the safety earth symbol or coloured GREEN or GREEN-AND-YELLOW. The wire which is coloured BLUE must be connected to the terminal in the plug which is marked with the letter N or coloured BLACK. The wire which is coloured BROWN must be connected to the terminal in the plug which is marked with the letter L or coloured RED. How to replace the fuse : Open the-fuse compartment with a screwdriver and replace the fuse and fuse cover. 3 Important Information This equipment should be used on PSTN lines requiring 2-wire Loop calling unguarded clearing with Loop Disconnect or DTMF address signalling. The equipment must be connected to direct extension lines and a payphone should not be connected as an extension. Operation in Power Failure In the event of a power failure, three single line telephones connected to Power Failure Transfer jacks will be directly connected to the following CO lines: KX-TD816 -- CO 1, CO 2, and CO 5 KX-TD1232 -- CO 1, CO 2, and CO 9 · Set the Dialling Mode (Tone or Pulse) of your telephone, according to the CO line. · 999 and 112 can be dialled on the apparatus for the purpose of making outgoing calls to the BT emergency (999) and (112) service. Satisfactory performance can not be guaranteed for every allowed combination of host and subsidiary apparatus. 999 and 112 can be dialled on the apparatus after accessing the CO line for the purpose of making outgoing calls to the BT emergency (999) and (112) service. During dialling, this apparatus may tinkle the bells of other telephones using the same line. This is not a fault and we advise you not to call Fault Repair Service. `Prevention of access by user. This apparatus is intended to be accessible only to authorized personnel. This apparatus must be installed in a locked room or similar environment, such that user access is prevented. Failure to prevent such user access will invalidate any approval given to this apparatus.' Caution: Do not push the PAUSE button more than twice following the initial access digit (or digits). Failure to comply with this requirement may result in unsatisfactory operation. Notice: This PBX should only be used on B·T lines on which specific BT services or facilities are provided. CAUTION Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer's instructions. 4 Attention · The apparatus is designed to be installed and operated under controlled conditions of ambient temperature and a relative humidity not greater than 60%. · Avoid installing the apparatus in damp or humid environments, such as bathrooms or swimming pools. · The apparatus shall not be exposed to dripping or splashing. · Keep the unit away from heating appliances and electrical noise generating devices such as fluorescent lamps, motors and televisions. These noise sources can interfere with the performance of the Digital Super Hybrid System. · This unit should be kept free of dust, moisture, high temperature (more than 40°C / 104°F) and vibration, and should not be exposed to direct sunlight. · Never attempt to insert wires, pins, etc. into the vents or other holes of this unit. · If there is any trouble, disconnect the unit from the telephone line. Plug a single line telephone directly into the telephone line. If the telephone operates properly, do not reconnect your system to the line until the system has been repaired. If the telephone does not operate properly, chances are that the problem is in the telephone network, and not in your system. · Do not use benzine, thinner, or the like, or any abrasive powder to clean the cabinet. Wipe it with a soft cloth. · The ISDN Line Units/Cards are in accordance with the European Telecommunication Standards (ETS). If your telephone company provides an ISDN service which follows standards other than ETS, some ISDN features may not work properly. (E.g. Charge Fee Reference, CLIP, COLP, etc.) WARNING THIS UNIT MAY ONLY BE INSTALLED AND SERVED BY QUALIFIED SERVICE PERSONNEL. WHEN A FAILURE OCCURS WHICH RESULTS IN THE INTERNAL PARTS BECOMING ACCESSIBLE, DISCONNECT THE POWER SUPPLY CORD IMMEDIATELY AND RETURN THIS UNIT TO YOUR DEALER. DISCONNECT THE TELECOM CONNECTION BEFORE DISCONNECTING THE POWER CONNECTION PRIOR TO RELOCATING THE EQUIPMENT, AND RECONNECT THE POWER FIRST. THIS UNIT IS EQUIPPED WITH AN EARTHING CONTACT PLUG. FOR SAFETY REASONS THIS PLUG MUST ONLY BE CONNECTED TO AN EARTHING CONTACT SOCKET WHICH HAS BEEN INSTALLED ACCORDING TO REGULATIONS. THE POWER SOCKET WALL OUTLET SHOULD BE LOCATED NEAR THIS EQUIPMENT AND BE EASILY ACCESSIBLE. TO PREVENT RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. 5 Attention The serial number of this product may be found on the label affixed to the bottom of the unit. You should note the serial number of this unit in the space provided and retain this book as a permanent record of your purchase to aid in identification in the event of theft. MODEL NO.: SERIAL NO.: For your future reference DATE OF PURCHASE NAME OF DEALER DEALER'S ADDRESS Warning This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. 73/23/EEC 89/336/EEC 92/31/EEC 93/68/EEC APPROVED for connection to telecommunication systems specified in the instructions for use subject to the conditions set out in them. 606055 APPROVED for connection to telecommunication systems specified in the instructions for use subject to the conditions set out in them. NS / 1010 / 235 / R / 604365 KX-TD816 KX-TD1232 6 Introduction This Installation Manual provides technical information for the Panasonic Digital Super Hybrid System, KX-TD816/KX-TD1232. It is designed to serve as an overall technical reference for the system and includes a description of the system, its hardware and software, features and services and environmental requirements. This manual contains the following sections: Section 1, System Outline. Provides general information on the system including system capacity and specifications. Section 2, Installation. Contains the basic system installation and wiring instructions, as well as how to install the optional cards and units. Section 3, Features. Describes all the basic, optional and programmable features in alphabetical order. It also provides information about the programming required, conditions, connection references, related features and operation for every feature. Section 4, System Programming. Provides step-by-step programming instructions for a proprietary telephone. Section 5, List. Lists tone/ring tone and default values of system programming. Section 6, Troubleshooting. Provides information for system and telephone troubleshooting. Section 7, PRI Section. Provides information on using the Primary Rate Interface (PRI) ISDN line with the optional expansion unit. Section 8, DECT Portable Station Section. Provides information on the wireless system, which can be optionally equipped with the basic system. NOTE The following documents may be used in conjunction with this manual: · User Manual for KX-TD816/KX-TD1232 System, DIGITAL Proprietary Telephones, Console, DECT Portable Station and Single Line Telephones · Programming Table The programming table is designed to be used as a hard copy reference to the userprogrammed data. 7 Installation Manual Contents Section 1 1.1 1.2 1.3 1.4 1.5 System Outline System Highlights ............................................................................. Basic System Construction .............................................................. Proprietary Telephones .................................................................... Options............................................................................................... Specifications..................................................................................... 1.5.1 General Description................................................................. 1.5.2 Characteristics ......................................................................... 1.5.3 System Capacity...................................................................... 1.5.4 Ports......................................................................................... 1-2 1-4 1-5 1-6 1-11 1-11 1-12 1-13 1-15 Section 2 2.1 2.2 Installation Before Installation ............................................................................ Installation of the Main Unit ........................................................... 2.2.1 Unpacking ............................................................................... 2.2.2 Name and Location ................................................................. 2.2.3 Wall Mounting......................................................................... 2.2.4 Frame Earth Connection.......................................................... 2.2.5 Opening Front Cover............................................................... Connection............................... ...