User manual PANASONIC LUMIX DMC-FZ30PP

Operating Instructions Digital Camera Model No. DMC-FZ30PP Before connecting, operating or adjusting this product, please read the instructions completely. For USA assistance, please call: 1-800-272-7033 or send e-mail to : digitalstillcam@panasonic.com For Canadian assistance, please call: 1-800-561-5505 or visit us at www.panasonic.ca VQT0R81 Before Use Before Use Dear Customer, We would like to take this opportunity to thank you for purchasing this Panasonic Digital Camera. Please read these Operating Instructions carefully and keep them handy for future reference. Information for Your Safety WARNING TO REDUCE THE RISK OF FIRE OR SHOCK HAZARD AND ANNOYING INTERFERENCE, USE ONLY THE RECOMMENDED ACCESSORIES AND DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE. DO NOT REMOVE THE COVER (OR BACK); THERE ARE NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. Carefully observe copyright laws. Recording of pre-recorded tapes or discs or other published or broadcast material for purposes other than your own private use may infringe copyright laws. Even for the purpose of private use, recording of certain material may be restricted. · Please note that the actual controls and components, menu items, etc. of your Digital Camera may look somewhat different from those shown in the illustrations in these Operating Instructions. · SD Logo is a trademark. · Other names, company names, and product names printed in these instructions are trademarks or registered trademarks of the companies concerned. THE SOCKET OUTLET SHALL BE INSTALLED NEAR THE EQUIPMENT AND SHALL BE EASILY ACCESSIBLE. CAUTION Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer's instructions. RBRC TM Li-ion A lithium ion/polymer battery that is recyclable powers the product you have purchased. Please call 1-800-8-BATTERY for information on how to recycle this battery. 2 VQT0R81 Before Use FCC Note: (U.S. only) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. · Consult the dealer or an experienced radio/TV technician for help. FCC Caution: To assure continued compliance, follow the attached installation instructions and use only shielded interface cables with ferrite core when connecting to computer or peripheral devices. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. Trade Name: Panasonic Model No.: DMC-FZ30 Responsible party: Panasonic Corporation of North America One Panasonic Way, Secaucus, NJ 07094 Support Contact: Panasonic Consumer Electronics Company 1-800-272-7033 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This Class B digital apparatus complies with Canadian ICES-003 3 VQT0R81 Before Use -If you see this symbolInformation on Disposal in other Countries outside the European Union This symbol is only valid in the European Union. If you wish to discard this product, please contact your local authorities or dealer and ask for the correct method of disposal. Care for the camera · Do not shake or cause impact to the camera. The camera may not be operated normally or recording of pictures may be disabled, or the lens may be damaged. · Sand or dust may cause a malfunction of the camera. When you use the camera on a beach etc., take care so that sand or dust does not get into the camera. · When you use the camera on a rainy day or on a beach, take care so that water does not get into the camera. · If seawater splashes onto the camera, wet a soft cloth with tap water, wring it well, and use it to wipe the camera body carefully. Then, wipe it again with a dry cloth. About the LCD monitor/Viewfinder · Do not press the LCD monitor strongly. It may cause uneven colors on the LCD monitor or a malfunction of the LCD monitor. · In a place with drastic temperature changes, condensation may form on the LCD monitor. Wipe it with a soft, dry cloth. · If the camera is extremely cold when you turn the camera on, the image on the LCD monitor/Viewfinder is slightly darker than usual at first. However, as the internal temperature increases, it goes back to the normal brightness. · When rotating the LCD monitor, be careful not to use excessive force. This may result in damage. · Depending on the tripod you are using, you may not be able to rotate the LCD monitor. · When not using the LCD monitor or when using the Viewfinder, it is recommended that you close the LCD monitor with the screen facing inwards to prevent dirt and scratches. Extremely high precision technology is employed to produce the LCD monitor/ Viewfinder screen. The result is more than 99.99% effective pixels with a mere 0.01% of the pixels inactive or always lit. However, this will not be recorded on the pictures in the card. 4 VQT0R81 Before Use About the Lens · Do not direct the lens to the sun or strong light sources. It may cause not only a malfunction of the camera but irreversible damage to your eye. · Do not press the lens strongly. · Leaving the camera with the lens facing the sun may cause a malfunction. Be careful when you put the camera outside or near a window. · When there is dirt (water, oil, and fingerprints, etc.) on the surface of the lens, the picture may be affected. Lightly wipe the surface of the lens with a soft, dry cloth before and after taking pictures. About Condensation (When the lens or the Viewfinder is fogged up) Condensation takes place when the ambient temperature or humidity is changed as follows: Be careful of condensation since it causes stains on the lens, fungus or malfunction. · When the camera is brought inside from the cold to a warm room. · When the camera is moved from outside to an air-conditioned car. · When cool wind from an air conditioner or other is directly blown onto the camera. · In humid places Put the camera into plastic bag until the temperature of the camera is close to the ambient temperature to avoid condensation. In case of condensation, turn the camera off and then leave it for about 2 hours. When the camera becomes close to the ambient temperature, the fog disappears naturally. If you will not be using the camera for a long time · Store the battery in a cool and dry place with a relatively stable temperature. (Recommended temperature: 15 oC to 25 oC (59 oF to 77 oF), Recommended humidity: 40% to 60%) · Be sure to remove the battery and the card from the camera. · When the battery is left inserted in the camera for a long time, discharge takes place even if the camera is turned off. If you leave the battery inserted for an extended period of time, it will be excessively discharged and it may become unusable even after it is charged. · To store the battery for a long period of time, we recommend charging it once every year and storing it again after you completely use up the charged capacity. · When you keep the camera in a closet or a cabinet, we recommend storing it with the desiccant (silica gel). · When storing the camera for long periods of time, it is recommended that you close the LCD monitor with the screen facing inwards. 5 VQT0R81 Before Use About These Operating Instructions About indications in these operating instructions SCN1 SCN2 Modes indicated here allow you to use the functions or settings described on this page. Set the Mode dial to any of the modes to use the functions or settings. Convenient or helpful information for use of the camera is described. About illustrations in these operating instructions Please note that the appearance of the product, the illustration or the menu screen are a little different from those in actual use. About illustrations of the cursor button In these operating instructions, the operations on the cursor button are described as illustrated below. e.g.: When you press the 4 button REV About the front dial and rear dial Instructions for using these dials in the operating instructions are given with illustrations that match the screen icons. · Rotate the front dial and rear dial slowly but surely. AE LOCK EVF/LCD DISPLAY MENU A: Front dial B: Rear dial 6 VQT0R81 Contents Before Use Information for Your Safety ....................... 2 About These Operating Instructions ......... 6 Taking Pictures using Auto Bracket ........ 55 Optical Image Stabilizer .......................... 56 Taking Pictures using Burst Mode .......... 57 Playback (basic) Playing Back Pictures ............................. 59 Multi Playback (9 screens, 16 screens, and 25 screens) ...............60 Using the Playback Zoom .......................61 Deleting Pictures..................................... 62 Preparation Standard Accessories ............................... 9 Names of the Components ..................... 10 Charging the Battery with the Charger ... 12 About the Battery (Charging/number of recordable pictures) ............................ 13 Inserting/Removing the Battery .............. 14 Inserting/Removing the Card .................. 15 About the Card........................................ 16 Removing the Lens Cap/Attaching the Strap.................................................... 17 Attaching/Removing the Lens Hood ....... 18 Setting Date/Time (Clock Set) ................ 20 About the Setup Menu ............................ 21 About the LCD Monitor/Viewfinder ......... 25 Approximate number of recordable pictures and the size ........................... 31 About the zoom....................................... 33 · Using the Optical Zoom .................... 33 · Using the Digital Zoom ..................... 34 · Using the extended optical zoom (EZ)......................................... 34 Recording pictures (advanced) Using the Mode Dial ............................... 64 · Aperture-priority AE .......................... 64 · Shutter-priority AE ............................ 65 · Manual exposure .............................. 66 · Motion picture mode ......................... 69 · [SCENE MODE] menu...................... 71 ­ Portrait mode ................................. 72 ­ Sports mode .................................. 72 ­ Food mode .................................... 73 ­ Scenery mode ............................... 73 ­ Night portrait mode ........................ 74 ­ Night scenery mode....................... 74 ­ Baby mode .................................... 75 ­ Soft skin mode............................... 76 ­ Candle light mode.......................... 76 ­ Party mode .................................... 77 ­ Fireworks mode ............................. 77 ­ Snow mode.................................... 78 ­ Starry sky mode............................. 79 ­ Panning mode ............................... 80 Recording pictures (basic) The Mode Dial ........................................ 36 Taking Pictures ....................................... 37 Taking Pictures in Auto Mode................. 42 Checking the Recorded Picture (Review) .............................................. 44 Taking Close-up Pictures [AF MACRO] ....................................... 45 Taking Pictures with Manual Focus ........ 46 Taking Pictures using the Built-in Flash ................................. 49 Taking Pictures with the Self-timer ......... 53 Compensating the Exposure .................. 54 Recording Menu Settings Using the [REC] mode menu .................. 81 · White Balance [W.BALANCE] .......... 82 · ISO Sensitivity [SENSITIVITY] ......... 84 · Aspect Ratio [ASPECT RATIO] ........ 84 · Picture Size [PICT.SIZE] .................. 85 · Quality [QUALITY] ............................ 86 · Audio Recording [AUDIO REC.] ....... 87 7 VQT0R81 · Metering Mode [METERING MODE]......................... 87 · AF Mode [AF MODE]........................ 88 · Continuous AF [CONT.AF] ............... 90 · AF Assist Lamp [AF ASSIST LAMP] .......................... 90 · Digital Zoom [D.ZOOM] .................... 91 · Color Effect [COL.EFFECT] ............. 91 · Picture Adjustment [PICT.ADJ.] ....... 92 · Flip Animation [FLIP ANIM.] ............. 92 · Conversion Lens [CONVERSION] ............................... 95 · Extra Flash [EXT.FLASH] ................. 97 · Extra Flash Burst Mode [EX.FLASH BURST]......................... 99 Connecting to a PC or Printer Before Connecting to the PC or the Printer [USB MODE] ................... 117 Connecting to a PC............................... 118 Connecting to a PictBridge-compliant Printer................................................ 121 Using the Remote Shutter .................... 125 Others Using the MC Protector/ND Filter ......... 126 Screen Display...................................... 127 Cautions for Use ................................... 129 Message Display .................................. 131 Troubleshooting .................................... 133 Specifications........................................ 137 Digital Camera Accessory System ....... 139 Digital Camera Accessory Order Form (For USA Customers) .... 140 Request for Service Notice (For USA Only).................................. 141 Limited Warranty (For USA Only) ......... 142 Customer Services Directory (For USA Only).................................. 144 Index ..................................................... 145 Spanish Quick Use Guide/ Guía rápida en español..................... 147 Playback (advanced) Playing Back Pictures with Audio/Motion Pictures ....................... 100 Using the [PLAY] mode menu .............. 101 · Playing Back with Slide Show [SLIDE SHOW]............................... 102 · Setting Favorites [FAVORITE]........ 103 · Displaying pictures in a direction at the time of recording [ROTATE DISP.] ............................ 104 · Rotating the Picture [ROTATE] ...... 105 · Setting the Picture to be Printed and the Number of Prints [DPOF PRINT]................................ 106 · Preventing Accidental Erasure of the Picture [PROTECT] ........................ 108 · Adding Audio to Recorded Pictures [AUDIO DUB.] ................................ 109 · Resizing the Pictures [RESIZE] ...... 110 · Trimming the Pictures [TRIMMING] ................................... 111 · Aspect ratio conversion [ASPECT CONV.]........................... 113 · Clean-up [CLEAN UP] .................... 114 · Initializing the Card [FORMAT] ....... 115 Playing Back Pictures on a TV Screen ................................. 116 8 VQT0R81 Preparation Preparation Standard Accessories Before using your camera, check the contents. o 1 RP-SD032B 2 3 CGR-S006A DE-993B 4 K1HA08CD0007 1 SD Memory Card (32 MB) (In the text, it is called the "Card") 2 Battery Pack (In the text, it is called the "Battery") 3 Battery Charger (In the text, it is indicated as "Charger") (This can be used with multiple product.) 4 USB Connection Cable 5 AV Cable 6 CD-ROM 7 Strap 8 Lens Cap 9 Lens Hood · For information about optional accessories, please refer to "Digital Camera Accessory System". (P139) 5 K1HA08CD0008 6 7 VFC4124 8 VYK1P30 9 VYQ3505 9 VQT0R81 Preparation Names of the Components 12 3 4 1 Lens (P5) 2 Front dial (P44, 60, 61, 64, 66) 3 Self-timer Indicator (P53) AF Assist Lamp (P90) 4 Flash (P49) 5 6 7 8 9 10 11 5 6 7 8 9 10 11 Diopter Adjustment Dial (P29) Viewfinder (P25, 127) [DISPLAY] Button (P25) [EVF/LCD] Button (P25) [AE LOCK] Button (P40) Speaker (P100) Rear dial (P39, 59, 65, 66) 12 13 14 15 16 17 LCD Monitor (P25, 26, 127) [MENU] Button (P21) Delete Button (P62) Cursor Buttons 2/Self-timer Button (P53) 4/[REV] Button (P44) 1/Flash Setting Button (P49) 3/Exposure Compensation (P54)/Auto Bracket (P55)/White Balance Fine Adjustment (P83)/Flash Output Adjustment (P51)/Backlight Compensation in auto mode (P43) Button 16 Card Door (P15) 17 LCD Monitor open knobs (P26) 12 13 14 15 10 VQT0R81 Preparation 18 19 20 A P 18 19 20 21 22 23 24 25 26 27 28 Zoom ring (P33) Focus ring (P46) Shutter Button (P37) Strap Eyelet (P17) Microphone (P69, 87) Hot Shoe (P97) Mode Dial (P36) Camera ON/OFF Switch (P21) Power Indicator (P37) Single or Burst Mode Button (P57) Optical Image Stabilizer Button (P56) 21 22 23 24 25 26 27 28 29 [FOCUS] Button (P47,77, 89) 30 Focus Switch (P42, 45, 46) (AF/AF MACRO/MF) 31 Flash Open Lever (P49) 32 [REMOTE] Socket (P125) 33 [AV OUT/DIGITAL] Socket (P116, 118, 121) 34 [DC IN] Socket (P118, 121) · Please be sure to use genuine Panasonic AC adaptor (DMW-CAC1; optional). 29 30 31 SCAN1 36 37 SCAN2 S M 32 33 34 35 35 36 37 38 Lens hood positioning groove (P18) Battery Door Open/Close Lever (P14) Battery Door (P14) Tripod Receptacle · When you use a tripod, make sure the tripod is stable with the camera attached to it. CLO SE OPEN 38 11 VQT0R81 Preparation Charging the Battery with the Charger When the camera is shipped, the battery is not charged. Charge the battery before use. 3 Detach the battery after charging is completed. 1 Attach the battery to the charger. 2 Connect the charger to the electrical outlet. · When the [CHARGE] indicator A lights in green, charging starts. · When the [CHARGE] indicator A turns off (in about 120 minutes), charging is completed. · After charging is completed, be sure to disconnect the charger from the electrical outlet. · The battery becomes warm after use/ charge or during charge. The camera also becomes warm during use. However, it is not a malfunction. · The battery is exhausted when it is left for a long period of time after being charged. Recharge the battery when it is exhausted. · Use the dedicated charger and battery. · Charge the battery with the charger indoors. · Do not disassemble or modify the charger. 12 VQT0R81 Preparation About the Battery (Charging/number of recordable pictures) Battery indication The remaining battery power appears on the screen. Playback time when using the LCD monitor Playback time Approx. 300 min · The battery indication turns red and blinks. · Recharge the battery or replace it with fully charged battery. [It does not appear when you use the camera along with the AC adaptor (DMW-CAC1; optional).] The battery life The number of recordable pictures by CIPA standard (In program AE mode) · CIPA is an abbreviation of [Camera & Imaging Products Association]. Number of Approx. 280 pictures recordable pictures (Approx. 140 min) The number of recordable pictures and playback time will vary depending on the operating conditions and storing condition of the battery. Charging Charging time Approx. 120 min Charging time and the number of recordable pictures with the optional battery pack (CGR-S006A) are the same as above. · When charging starts, the [CHARGE] indicator lights. Charging error · If a charging error occurs, the [CHARGE] indicator blinks in about 1 second cycles. In this case, disconnect the charger from the electrical outlet, remove the battery and make sure that both room and battery temperature are not too low or high and then charge it again. If the [CHARGE] indicator still blinks even if you charge the battery for a while, consult the dealer or your nearest servicenter. · When the operating time of the camera becomes extremely short even if the battery is properly charged, the life of the battery may have expired. Buy a new battery. Charging conditions · Charge the battery under temperature of 10 oC to 35 oC (50 oF to 95 oF). (Battery temperature should be the same also.) · The performance of the battery may be temporarily deteriorated and the operating time may become shorter in low temperature conditions (e.g. skiing/ snowboarding). Recording conditions by CIPA standard · Temperature: 23 °C (73.4 °F)/ Humidity: 50% when LCD monitor is on. · Using the supplied SD Memory Card (32 MB). · Using the supplied battery. · Recording starts 30 seconds after the camera is turned on. · Recording once every 30 seconds, with full flash every other recording. · Turn the camera off every 10 recordings. The number of recordable pictures varies depending on the recording interval time. If the recording interval time becomes longer, the number of recordable pictures decreases. (When taking a picture every 2 minutes: Approx. 75) The number of recordable pictures when using the Viewfinder (Recording conditions comply with CIPA standard.) Number of Approx. 300 pictures recordable pictures (Approx. 150 min) 13 VQT0R81 Preparation Inserting/Removing the Battery · Check that the camera is turned off. · Close the flash. 1 Slide the release lever in the direction of the arrow to open the battery door A. 3 1 Close the battery door. 2 Slide the release lever as far as it will go in the direction of the arrow to close the battery door firmly. OSE CL OPE N OSE CL OPE N · Please be sure to use genuine Panasonic batteries (CGR-S006A). 2 Insert: Insert the charged battery until it clicks. Remove: Slide the lock B to remove the battery. · If you will not be using the camera for a long time, remove the battery. · When a fully charged battery has been inserted for more than 24 hours, the clock setting is stored (in the camera) for at least 3 months even if the battery is removed. (The storing time may be shorter if the battery is not charged sufficiently.) If more than 3 months has passed, the clock setting will be lost. In this case, set the clock again. (P20) · Do not remove the card and the battery while the card is being accessed. The data on the card may be damaged. (P16) · Do not remove the battery with the camera turned on since the settings on the camera may not be stored properly. · The supplied battery is designed only for the camera. Do not use it with any other equipment. 14 VQT0R81 Preparation Inserting/Removing the Card · Check that the camera is turned off. · Close the flash. · The card may be damaged if it is not fully inserted. 1 Slide the card door to open it. 3 1 Close the card door. 2 Slide the card door to the end to close it firmly. · The card and the data may be damaged if it is inserted or removed while the camera is on. · We recommend using Panasonic's SD Memory Card. (Use only the genuine SD card with SD Logo.) · If the card door cannot be completely closed, remove the card and insert it again. 2 Insert: Insert the card fully until it clicks and it is locked with the label facing the front of the camera. Remove: Push the card until it clicks, then pull the card out upright. · Check the direction of the card. · Do not touch the connection terminals on the back side of the card. 15 VQT0R81 Preparation About the Card Access to the card When pictures are being recorded onto the card, the card access indication A lights red. 5 switch is unlocked, these functions become available.) SD Memory Card When the card access indication lights, pictures are being read or deleted or the card is cleaned up (P114) or formatted (P115). do not: · turn the camera off. · remove the battery or the card. · shake or impact the camera. The card and the data may be damaged and the camera may not operate normally. About handling a card Transfer important pictures/motion pictures from your card to your PC periodically (P118). The data on the card may be damaged or lost due to electromagnetic wave, static electricity, breakdown of the camera or a defective card. · Do not format the card on your PC or other equipment, format it with the camera only to ensure proper operation. (P115) SD Memory Card (supplied) and MultiMediaCard (optional) · The SD Memory Card and MultiMediaCard are small, lightweight, removable external cards. The reading/ writing speed of an SD Memory Card is fast. The SD Memory Card is equipped with a Write-Protect switch B that can inhibit writing and formatting a card. (When the switch is slid to the [LOCK] side, it is not possible to write or delete data on the card and format it. When the · On this unit, you can use SD Memory Cards of the following capacity (from 8 MB to 2 GB). 8 MB, 16 MB, 32 MB, 64 MB, 128 MB, 256 MB, 512 MB, 1 GB, 2 GB (Maximum) Please confirm the latest information on the following website. http://panasonic.co.jp/pavc/global/cs (This Site is English only.) · This unit supports SD Memory Cards formatted in FAT12 system and FAT16 system based on SD Memory Card Specifications. · This unit does not support MultiMediaCard for recording motion pictures. · The reading/writing speed of a MultiMediaCard is slower than an SD Memory Card. When a MultiMediaCard is used, the performance of certain features may be slightly slower than advertised. · After recording motion pictures using the MultiMediaCard, the card access indication may appear for a while, but this is not a malfunction. · Keep the Memory Card out of reach of children to prevent swallowing. 16 VQT0R81 Preparation Removing the Lens Cap/Attaching the Strap Remove the lens cap Attaching the strap (supplied) 1 Pinch the lens cap and remove it. 1 Pass the strap through the hole at the Strap Eyelet. 2 Pass the strap through the stopper and fasten the strap. · When you turn the camera off, carry the camera or play back the pictures, attach the lens cap to protect the surface of the lens. · Detach the lens cap before taking pictures. · Be careful not to lose the lens cap. A: Pull the strap 2 cm or more. · Attach the strap to the other side of the camera being careful not to twist it. · Check that the strap is firmly attached to the camera. · Attach the strap so that you can see "LUMIX" logo. 17 VQT0R81 Preparation Attaching/Removing the Lens Hood In bright sunlight or backlight, the lens hood will minimize lens flare and ghosting. The lens hood cuts out excess light and improves the picture quality. · Check that the camera is turned off. · Close the flash. When attaching the lens hood Temporarily storing the lens hood (Temporary storage) 1 1 Place the camera upside down. 2 Align lens hood mark A with lens hood positioning groove B on the unit and insert it straight in 1 1 Place the camera upside down. 2 Remove the lens hood and turn it around, aligning lens hood mark A with lens hood positioning groove B on the unit, and insert it straight in When removing the lens hood Press lock release button C and remove the lens hood · Make sure the lens hood is properly attached. When removing the lens hood Press lock release button C and remove the lens hood 18 VQT0R81 Preparation 2 Attach the lens cap. · Ensure that the lens cap is firmly attached. · When temporarily storing the lens hood, ensure that it is firmly attached and that it is not reflected in the picture. · When temporarily storing the lens hood, you can detach the lens cap and take pictures. However you cannot use the zoom ring, focus ring, [FOCUS] button or focus switch. · If you use a flash when the lens hood is attached, the light from the flash is blocked by the lens hood. The bottom of the screen becomes dark (vignetting) and you cannot adjust the flash setting. We recommend removing the lens hood before taking pictures with a flash. · When using the AF assist lamp in the dark, detach the lens hood. · For details on how to attach the MC protector and the ND filter, refer to P126. · When the lens hood is attached, you cannot attach conversion lenses. · If any of the accessories are lost, please contact Panasonic's parts department at 1 800 833-9626 (For USA) or in Canada call 1 800 561-5505 for more details on how to obtain replacement parts. 19 VQT0R81 Preparation Setting Date/Time (Clock Set) Initial setting The clock is not set when the camera is shipped. When you turn the camera on, the following screen appears. 2 Select [M/D/Y], [D/M/Y] or [Y/M/D]. CLOCK SET 10:001DEC.11.2005 M/D/Y PLEASE SET THE CLOCK CLOCK SET MENU SELECT SET EXIT MENU · When pressing the [MENU] button, the screen shown in step 1 appears. · The screen disappears after about 5 seconds. Turn the camera on again or press the [MENU] button, select [CLOCK SET] in page 2/4 of the [SETUP] menu (P23) and set the clock in steps 1 and 2. · Close the menu by pressing the [MENU] button 2 times after finishing the setting. · Check if the clock setting is correct, after turning the camera off and on. 1 Set date and time. CLOCK SET 00 : 00 JAN . 11 . 2005 M/D/Y SELECT SET EXIT MENU · 2/1: Select the desired item. · 3/4: Set date and time. · When a fully charged battery has been inserted for more than 24 hours, the clock setting is stored (in the camera) for at least 3 months even if the battery is removed. (The storing time may be shorter if the battery is not charged sufficiently.) If more than 3 months has passed, the clock setting will be lost. In this case, set the clock again. · You can set the year from 2000 to 2099. The 24-hour system is used. · When you use a photo printing service, if the date is not set in the camera, it will not be printed, even if the store provides a date printing option to your photo. · For the date print setting, refer to P107. 20 VQT0R81 Preparation About the Setup Menu · Set the items if necessary. (Refer to P22­ 24 for each menu item.) 4 Select the desired item. SETUP MONITOR AUTO REVIEW PLAY ON LCD POWER SAVE MF ASSIST SELECT SET EXIT MENU 1/ 4 1 Turn the camera on. OFF ON 5 Select the desired value. · The menu items depend on the mode selected with the mode dial (P36). In this page, the setup menu [MONITOR] settings in program AE mode [ ] are shown as an example. SETUP MONITOR AUTO REVIEW PLAY ON LCD POWER SAVE MF ASSIST SELECT REC MENU 1/ 4 2 Press the [MENU] button. 1/ 3 SET EXIT MENU SETUP AUTO AUTO W.BALANCE SENSITIVITY ASPECT RATIO PICT.SIZE QUALITY SELECT Be sure to press 1 at the end to store the setting. · Close the menu by pressing the [MENU] button after finishing the setting. In recording mode, you can also close the menu by pressing the shutter button halfway. 8M EXIT MENU 3 Select the [SETUP] Menu. REC MONITOR AUTO REVIEW PLAY ON LCD POWER SAVE MF ASSIST SELECT SETUP n0 1SEC. OFF 2MIN. MF1 1/4 EXIT MENU · Rotate the front dial A to switch between pages 1/4, 2/4, 3/4 and 4/4. 21 VQT0R81 Preparation [SETUP] menu (Refer to P21 for the setting method.) [MONITOR/VIEWFINDER] Adjust the brightness of the LCD monitor (when pictures appear on the LCD monitor) or Viewfinder (when pictures appear on the Viewfinder) in 7 steps. [AUTO REVIEW] [OFF]: The recorded picture does not automatically appear. [1SEC.]: The recorded picture automatically appears on the screen for about 1 second. [3SEC.]: The recorded picture automatically appears on the screen for about 3 seconds. [ZOOM]: The recorded picture automatically appears on the screen for about 1 second. Then it is enlarged 4 times and appears for about 1 second. This mode is useful for confirming focus. Pictures in auto bracket, burst mode or pictures with audio are not enlarged even if [ZOOM] is selected. · In motion picture mode [ ], auto review function is not activated. · When pictures are recorded in auto bracket [ ] (P55) or any speed ([ ], [ ] and [ ]) on burst mode (P57), the auto review function is activated regardless of the setting on the auto review function. (The picture is not enlarged.) · When using pictures with audio, the auto review function works while recording the audio or the data into the card regardless of the setting on the auto review function. (The picture is not enlarged.) · When the quality is set to [TIFF] or [RAW], the auto review function works until the end of recording onto the card. (The picture is not enlarged.) · The setting for the auto review function is disabled in auto bracket, burst mode, motion picture mode, or when [AUDIO REC.] is set to [ON]. [PLAY ON LCD] When Viewfinder is selected in the recording mode while setting [PLAY ON LCD] to [ON], the picture automatically appears on the LCD monitor in review or playback. (P29) 22 VQT0R81 Preparation [SETUP] menu (Refer to P21 for the setting method.) [POWER SAVE] [1MIN.]/[2MIN.]/[5MIN.]/[10MIN.]: The power save mode is activated (the camera is automatically turned off to save the battery life) if the camera has not been used for the time selected on the setting. [OFF]: The power save mode is not activated. · Press the shutter button halfway or turn the camera off and on to cancel the power save mode. · When using the AC adaptor (DMW-CAC1; optional)/connecting to a PC or a printer/ recording motion pictures/playing back motion pictures/during Slide Show, the power save mode is not activated. (However, during a manual Slide Show, the setting for the power save mode is fixed to [10MIN.]) [MF ASSIST] (Recording mode only) In manual focus, assistance screen appears on the center of the screen to facilitate focusing on the subject. (P46) [MF1]: The center of the screen is enlarged. You can adjust the focus while determining the composition of the whole of the screen. [MF2]: The whole of the screen is enlarged. It is convenient for adjusting the focus in Wide. [OFF]: The screen is not enlarged. [ [ [ [BEEP] ]: No operational sound ]: Soft operational sound ]: Loud operational sound [VOLUME] The volume of speakers can be adjusted in 7 steps. (LEVEL 6 to 0) · When you connect the camera to a TV, the volume of the speakers of the TV is not changed. [CLOCK SET] Change date and time. (P20) [NO.RESET] Set this when you want to start the file number of the picture from 0001 on the next recording. (The folder number is updated, and the file number starts from 0001.) · The folder number can be assigned from 100 to 999. When the folder number reaches 999, you cannot reset the file number. We recommend formatting the card after saving the data on a PC or elsewhere. · To reset the folder number to 100, format the card first and then use this function to reset the file number. After that, the reset screen for the folder number appears. Select [YES] to reset the folder number. · Refer to P119 for detailed information about the file number and the folder number. [SHUTTER] Set to select the volume of shutter sound. [ ]: No shutter sound [ ]: Soft shutter sound [ ]: Loud shutter sound 23 VQT0R81 Preparation [SETUP] menu (Refer to P21 for the setting method.) [RESET] The settings on the [REC] or the [SETUP] menu are reset to the initial settings. · The birthday setting for [BABY] (P75) in the scene mode is also reset when the settings in the [SETUP] menu are reset. [ROTATE DISP.] (P104) in the [PLAY] mode menu is also reset to [ON]. · The folder number and the clock setting are not changed. [USB MODE] Set the USB communication system. · Set before connecting to a PC or a printer. (P117) [HIGHLIGHT] When the auto review or review function is activated, a white saturated area appears blinking in black and white. (P29) [VIDEO OUT] (Playback mode only) (P116) [NTSC]: Video output is set to NTSC system. [PAL]: Video output is set to PAL system. [SCENE MENU] [OFF]: [SCENE MODE] menu does not appear when setting the mode dial to [ ] or [ ] and the camera is operated in the scene mode currently selected. If you change the scene mode, Press the [MENU] button to display the [SCENE MODE] menu and then select the desired scene mode. [AUTO]: [SCENE MODE] menu appears automatically when setting the mode dial to [ ] or [ ]. Select the desired scene mode. [LANGUAGE] Set to the language on the menu screen from the following languages. Set to the desired language with 3/4 and store it with 1. [ENGLISH]: English [DEUTSCH]: German [FRANÇAIS]: French [ESPAÑOL]: Spanish [ITALIANO]: Italian [ ]: Chinese (Traditional) [ ]: Japanese · When you set to other language by mistake, select [ ] from the menu icons to set the desired language. 24 VQT0R81 Preparation About the LCD Monitor/Viewfinder EVF/LCD DISPLAY In recording mode (P37) 5 5 BACKLIGHT 1 2 3 1 Switching the LCD monitor/ Viewfinder Press the [EVF/LCD] button to switch the monitor screen. (When the LCD monitor is closed with the screen facing outwards) A LCD monitor (LCD) B Viewfinder (EVF) · When the LCD monitor turns on, the Viewfinder turns off (and vice versa). 2 Selecting the screen to be used Press the [DISPLAY] button to change the display. · When the menu screen appears, the [DISPLAY] button is not activated. During multi playback (P60) or playback zoom (P61) and when playing back with Slide Show (P102), the indications on the screen can be turned on and off. C Normal display D Display with histogram E Out-of-frame display F No display (Recording guide line) G No display ¢1 Backlight Compensation (Appears only in auto mode) ¢2 Histogram ¢3 When the number of pictures remaining is more than 1000 or the time remaining in motion picture mode is more than 1000 seconds, [ ] is displayed. 25 VQT0R81 Preparation In playback mode (P59) 100 _ 0001 1/5 LCD Monitor Adjusting the LCD monitor makes it possible to take pictures from various angles. Taking pictures at a normal angle. · You can switch between the LCD monitor and the Viewfinder. 100 _ 0001 1/5 9 months 10days 10:00 DEC. 1.2005 4 F2.8 1/25 ISO100 AUTO 10:00 DEC. 1.2005 H Normal display I Display with recorded information and histogram J No display ¢4 Displayed when you set birthday setting for [BABY] (P75) in the scene mode, and [WITH AGE] is selected at taking pictures. Taking pictures at a high angle Open the LCD monitor with one of the LCD monitor open knobs. · You can use the LCD monitor only. A:LCD Monitor open knobs · This is convenient when there is someone in front of you and you cannot get close to the subject. 26 VQT0R81 Preparation Taking pictures at a low angle Open the LCD monitor with one of the LCD monitor open knobs, pull the LCD monitor fully open (approximately 120o) and rotate it 180o. · You can use the LCD monitor only. LCD monitor rotation direction · If the LCD monitor turns on when it is closed with the screen facing inwards, the camera automatically switches to the Viewfinder. · If the LCD monitor is opened when the Viewfinder is turned on, the camera automatically switches to the LCD monitor. · Only rotate the LCD monitor after opening it wide enough, and be careful not to use excessive force as it may be damaged. · When holding the edge of the LCD monitor, there may be some distortion, however this is not a malfunction. Moreover, this has no affect on the taken pictures or playback. · When not using the LCD monitor it is recommended that you close it with the screen facing inwards to prevent dirt and scratches. · When using a tripod, depending on the kind of tripod the LCD monitor may not rotate. About the Viewfinder The Viewfinder is convenient when you want to take pictures of a moving subject or outdoors. · Refer to page 29 for information about diopter adjustment. · When using the Viewfinder, close the LCD monitor. · When the LCD monitor is open, the Viewfinder cannot be used. 1: Maximum 180o 2: Maximum 120o · This is convenient when taking pictures of flowers etc. that are in a low position. 27 VQT0R81 Preparation Tips for taking good pictures To take pictures without blurring: · Hold the camera gently with both hands, keep arms stationary at your side and stand with your feet slightly apart. · Make sure that camera shake does not occur when you press the shutter button. · Do not cover the microphone or the AF assist lamp with your finger or other objects. · Do not touch the front of the lens. When recording with LCD Monitor Direction detection function · If you take pictures by holding the camera vertically, the information of the rotation on the pictures is automatically added and recorded to the pictures. When [ROTATE DISP.] (P104) is set to [ON], you can rotate and display pictures on the screen or the TV according to the information of the rotation on the pictures. · This function may not work properly on pictures recorded by aiming the camera up or down. · You cannot use the direction detection function in motion picture mode [ ] and when you create flip animation. When recording with Viewfinder A: When holding the camera vertically · If you take pictures by holding the camera vertically, use the LCD monitor at the normal angle. · Refer to page P39 for information about jitter (camera shake). 28 VQT0R81 Preparation Out-of-frame display The recording information is displayed out of the recording screen, therefore, you can take pictures without obstruction from icons or others on the monitor, except the zoom and important warning indicators. Diopter adjustment This feature is handy for users who wear corrective lenses and prefer to use the Viewfinder. · Close the LCD monitor and press the [EVF/LCD] button to display the viewfinder. Adjust the diopter, rotating the diopter adjustment dial. Recording guide line When you align the subject on the horizontal and vertical guide lines or the cross point of these lines, you can take pictures with well-designed composition by viewing the size, the slope and the balance of the subject. Highlight display When setting [HIGHLIGHT] to [ON] on the [SETUP] menu (P24) while the auto review or review function is activated, any white saturated area (extremely bright or glistening part) on the picture appears blinking in black and white. · If you compensate the exposure to minus, referring to the histogram and then take a picture again, it may result in a good picture. No highlight display REVIEW1X 5 Monitor priority When setting [PLAY ON LCD] to [ON] on the [SETUP] menu (P22), the LCD monitor is turned on in the following cases. You can save the time it takes to switch the display to the LCD monitor even when using the Viewfinder in recording. · When the recording mode is switched to playback mode. · When reviewing pictures. (P44) · When turning the camera on in playback mode. EXIT 4X DELETE With highlight display REVIEW1X EXIT 4X DELETE 29 VQT0R81 Preparation Histogram · A histogram is a graph that displays brightness along the horizontal axis (black to white) and the number of pixels at each brightness level on the vertical axis. · It allows the camera user to easily check the way a picture is being exposed. · It is very useful if manual adjustments of the lens aperture and shutter speed are available, especially in those situations where automatic exposure may be difficult due to uneven lighting. Using the histogram feature will allow you to get the best performance from the camera. A When the values are concentrated to the left, the picture is under exposed. B When the values in the histogram are distributed evenly, the exposure is adequate and the brightness is well-balanced. C When the values are concentrated to the right, the picture is over exposed. Example of histogram 100 _ 0001 1/5 · When the recorded picture and the histogram do not match each other under the following conditions, the histogram is displayed in orange. ­ When the flash is activated ­ When the flash is closed 1 When the brightness of the screen is not correctly displayed in dark places 2 When the exposure is not adequately adjusted · The histogram does not appear when in motion picture mode [ ], during multi playback and playback zoom. · The histogram in the recording mode is an approximation. · The histogram in recording and playback may not match each other. · The histogram in the camera does not match the one displayed in image editing software used with a PC, etc. · Check white saturated areas with the highlight display in the auto review function or the review function. (P29) F2.8 1/200 ISO100 AUTO 10:00 DEC. 1.2005 100 _ 0001 1/5 F2.8 1/100 ISO100 AUTO 10:00 DEC. 1.2005 100 _ 0001 1/5 F2.8 1/50 ISO100 AUTO 10:00 DEC. 1.2005 A Under Exposed B Properly Exposed C Over Exposed ¢Histogram 30 VQT0R81 Preparation Approximate number of recordable pictures and the size Aspect Ratio Picture size Quality 16 MB 32 MB 64 MB 128 MB 256 MB 512 MB 1 GB 2 GB Aspect Ratio Picture size Quality 16 MB 32 MB 64 MB 128 MB 256 MB 512 MB 1 GB 2 GB 2 4 10 20 39 78 155 310 14 30 62 125 240 480 970 1920 28 59 120 240 470 940 1880 3610 3 7 15 31 61 120 240 490 22 46 94 190 370 730 1470 2920 41 86 175 350 690 1370 2740 5120 (2M EZ): (1600k1200 pixels) (1M EZ): (1280k960 pixels) 0 1 2 4 9 19 38 77 3 7 15 31 61 120 240 490 7 15 31 62 120 240 480 970 0 1 3 7 13 27 54 105 0 1 3 8 15 30 61 125 5 12 25 51 99 195 390 790 11 24 49 100 195 380 770 1530 1 3 6 12 24 48 96 195 9 19 39 79 150 300 610 1220 17 37 75 150 290 590 1180 2360 (8M): (3264k2448 pixels) (5M EZ): (2560k1920 pixels) (3M EZ): (2048k1536 pixels) 31 VQT0R81 Preparation Aspect Ratio Picture size Quality 16 MB 32 MB 64 MB 128 MB 256 MB 512 MB 1 GB 2 GB Aspect Ratio Picture size Quality 16 MB 32 MB 64 MB 128 MB 256 MB 512 MB 1 GB 2 GB 0 1 3 7 14 28 57 115 5 11 23 47 92 180 360 740 10 22 46 93 180 350 710 1420 1 2 4 9 18 36 72 145 2 4 9 18 36 72 145 290 13 28 58 115 230 450 910 1800 25 54 110 220 430 860 1720 3410 (5.5M): (3072k1728 pixels) (2M EZ): (1920k1080 pixels) 0 1 2 5 10 21 43 87 4 8 17 36 70 135 270 560 8 17 35 71 135 270 540 1090 0 1 3 7 15 30 60 120 1 2 4 8 17 34 69 140 6 13 28 57 110 220 440 890 12 27 55 110 210 430 860 1700 1 3 6 14 27 54 105 210 10 21 44 89 170 340 680 1360 19 41 84 170 330 650 1310 2560 (7M): (3248k2160 pixels) (4.5M EZ): (2560k1712 pixels) (2.5M EZ): (2048k1360 pixels) · The aspect ratio is the horizontal to vertical ratio of a picture. Refer to P84 for the aspect ratio. · If you set the quality to [RAW], the picture size is fixed to the maximum picture size for each aspect ratio. · If you select a larger picture size, you can print pictures clearly. When you select a smaller picture size, you can record more pictures. (P85) · EZ is an abbreviation for [Extended Optical Zoom]. Selecting a picture size with EZ displayed, allows you to magnify the subject up to a maximum of 19.1 times when the digital zoom is set to [OFF]. (P34) · Refer to P86 for information about quality. · The numbers are approximations. (The numbers vary depending on the recording condition and the type of the card.) · The number of recordable pictures varies depending on subjects. · The remaining number of recordable pictures displayed on the screen is an approximation. 32 VQT0R81 Preparation About the zoom Using the Optical Zoom SCN1 SCN2 You can make people and subjects appear closer with the 12 times optical zoom, and landscapes can be recorded in wide angle. To make subjects appear further away use (Wide) 5 1X To make subjects appear closer use (Tele) 5 · The picture may have some distortion (typical example: vertical straight line bent outwards). This is due to the lens aberration, which is common to some extent with all photographic lenses. Distortion may be more visible when using a wider area of the zoom lens as you get closer to the subject. · When using the zoom lens at high magnification, the quality of the picture can be enhanced if a tripod is used. At high magnification, even small movements can cause a slight decrease in picture sharpness. · If you use the zoom function after focusing on the subject, focus on the subject again. · The indicated zoom magnification is an approximation. · When you rotate the zoom ring, you may hear some sound from the camera or the camera may be shaken. This is not a malfunction. 12X A: Zoom ring 33 VQT0R81 Preparation Using the Digital Zoom SCN1 SCN2 In the [REC] menu (P81), setting [D.ZOOM] to [2k] or [4k] allows you to magnify a subject up to a maximum of 48 times. (Except when using extended optical zoom.) W W W T T T · When using the digital zoom, we recommend using a tripod and the self-timer (P53) for taking pictures. · The indicated zoom magnification is an approximation. · When using the digital zoom, the AF area is displayed with a size wider than usual and set only to a point on the center of the screen. (P89) Using the Extended Optical Zoom (EZ) SCN1 SCN2 1 Optical zoom 2 Digital zoom The digital zoom and extended optical zoom can be used together. Example:When the digital zoom is set to [4k]and the picture size to (3M EZ), you can use the extended optical zoom [ ] at the same time. W T Normally you can make people and subjects appear up to 12 times closer with the optical zoom. However if you set the picture size to [ ] [3M EZ] etc., the extended optical zoom is activated and the zoom is further enhanced as shown below. 35 mm 3 When using the digital zoom [4k]and the extended optical zoom [3M EZ (maximum19.1times )] together. Picture size with the extended optical zoom not activated (example: [ ] (8M)) Picture size with the extended optical zoom activated (example: [ ] (3M EZ)) 420 mm · The digital zoom is temporarily set to [OFF] in the following cases. ­ When taking pictures in auto mode [ ] (P42) ­ When the quality is set to [RAW] (P86) ­ When [CONVERSION] on the [REC] menu is set to [ ] (P95) · When using the digital zoom, the picture quality becomes deteriorated. · When using the digital zoom, the stabilizer function may not be effective. 668 mm 34 VQT0R81 Preparation Picture size and maximum zoom magnification (±: Available, --: Not available) Aspect ratio Picture size Maximum zoom magnification Extended optical zoom (8M) (7M) (5.5M) (5M EZ) (4.5M EZ) (3M EZ) (2M EZ) (1M EZ) (2.5M EZ) (2M EZ) 19.1k 12k -- 15.3k ± · You can further enhance the zoom magnification with the extended optical zoom without worrying about further picture distortion. · If you set a picture size that activates the extended optical zoom, the extended optical zoom icon [ ] is displayed on the LCD monitor when you use the zoom function. · The zoom movement quickens near Wide (1k) when using the extended optical zoom. · When you rotate the zoom ring near the Tele position, the on-screen zoom indication may momentarily pause. This is not a malfunction. · Setting [D.ZOOM] in the [REC] mode menu to [ON] allows you to use the digital zoom for recording an even larger picture. However picture quality willl deteriorate. (P34) · In motion picture mode [ ], the extended optical zoom does not work. Extended optical zoom mechanism · When you set the picture size to [ ] (3M EZ) (3 million pixels), the 8M (8 million pixels) CCD area is cropped to the centre 3M (3 million pixels) area, allowing a picture with a higher zoom effect. 35 VQT0R81 Recording pictures (basic) Recording pictures (basic) The Mode Dial This camera has a mode dial to suit recording of many kinds of scenes. Select the desired mode and enjoy the variety of recording. Rotate the mode dial slowly and securely. S M : Scene mode 1 : Scene mode 2 (P71) This mode allows you to take pictures depending on the recording scenes. This mode also allows you to set [SCENE MENU] (P24) on the [SETUP] menu to [OFF] and set the scene modes which are frequently used to [ ] and [ ] on the mode dial. It is convenient because you can select the scene mode quickly and minimize the operation. : Playback mode (P59) This mode allows you to play back recorded pictures. : Auto mode (P42) Even beginners can easily take pictures. A P : Program AE mode (P37) The exposure is automatically adjusted by the camera. : Aperture-priority AE (P64) The shutter speed is automatically determined by the aperture value you set. : Shutter-priority AE (P65) The aperture value is automatically determined by the shutter speed you set. : Manual exposure (P66) The exposure is adjusted by the aperture value and the shutter speed which are manually adjusted. : Motion picture mode (P69) This mode allows you to record motion pictures. 36 VQT0R81 SCN1 SCN2 Recording pictures (basic) Taking Pictures Program AE · A: Press the shutter button halfway to focus. · The focus indication 2 is lit and then the aperture value 3, the shutter speed 4 and program shift 5 are displayed. · When 9-area-focusing or 3-area-focusing (High speed) is used for AF mode, the AF area will not appear until the subject is brought into focus. (P88) · Refer to P39 for information about Program shift and P89 for information about selecting the AF area. The camera automatically sets the shutter speed and the aperture value according to the brightness of the subject. · Remove the lens cap. 1 1 Turn the camera on. 2 Set the mode dial to program AE mode [ ]. S M SCN1 SCN2 OFF ON A P 3 Take a picture. F2.8 1/25 · The power indicator (green) lights. When it blinks, the remaining battery power is low. Insert a fully charged battery.