User manual PANASONIC UBT780

Operating Instructions (For Basic Operations) Electronic Board (elite Panaboard) Model No. UB-T780 English Español Deutsch 1 2 3 4 UB-T780 Stand is sold separately. English: These operating instructions consist of the following languages. Español: En estas instrucciones de funcionamiento se incluyen los siguientes idiomas. Deutsch: Diese Bedienungsanleitung liegt in folgenden Sprachen vor. English Spanish Español German Deutsch Operating Instructions (For Basic Operations) Electronic Board (elite Panaboard) Model No. UB-T780 UB-T780 Stand is sold separately. Installation Manual Included (for qualified service personnel) · To assemble this unit, please refer to the Installation Manual on pages 29 through 47. · Before operating this unit, please read these instructions completely and keep them carefully for future reference. · This unit is designed for installation by a qualified servicing dealer. Installation performed by non-authorized individuals could cause safety-related problems with the operation of this equipment. For U.S.A. only: · To locate the closest authorized dealer in your area, please call 1-800-449-8989. Introduction Introduction Thank you for purchasing the Panasonic Electronic Board. For optimum performance and safety, please read these instructions carefully. Feature Highlights By connecting the elite Panaboard to a computer and using a projector to display the contents of the computer's screen on the elite Panaboard, you can do the following. Electronic Pen Features · Manipulate objects on the computer screen by using the electronic pen as a mouse. · Draw and erase lines on the computer screen by using the electronic pen. · Save images of the computer screen that were created by drawing with the electronic pen. Screen Shade Hide a portion of the screen by displaying it as a gray box. Magnification Enlarge a portion of the screen to display a detailed section (e.g., a map). elite Panaboard book Use the elite Panaboard book software that supports elite Panaboard operations, such as writing, drawing, attaching images and computer operations. This software lets you save the contents of the screen on your computer and retrieve it for later use. Usage Scenarios For Education · Create an effective learning environment by projecting a variety of educational software onto the elite Panaboard and, with the electronic pen, directly manipulate the software and write and draw on the screen. · With several tools at your disposal for aiding in explanations, such as illustration and marker tools, you can keep students' attention through a dynamic screen display. · Draw your students' interest by using the screen shade feature to show questions to students while hiding the answers, and incrementally showing the rest of the screen. · The teacher can prepare materials before class to display on the elite Panaboard. For Business · Visually communicate your product's characteristics and create an appealing presentation of your product by displaying images and using the electronic pen to highlight key points. · Display the contents, including what you have written using the electronic pen, of the elite Panaboard in your company in real time on a remote computer by using TV conferencing equipment. 2 Operating Instructions (For Basic Operations) Introduction Things you should keep a record of Attach your sales receipt here For your future reference Date of purchase Serial number Dealer's name Dealer's address Dealer's tel no. 1 About the Operating Instructions There are 2 separate operating manuals for the elite Panaboard. For Basic Operations (this document) Instructions for connecting and operating the elite Panaboard, as well as instructions for installation construction. Instructions for the included elite Panaboard software and elite Panaboard book. The manual "Operating Instructions (For Software)" is located on the included CD-ROM. You can view the "Operating Instructions (For Software)" after you install the elite Panaboard Software on your computer. For details on viewing the manual, see "Viewing the Electronic Documentation" (page 22). For Software (electronic documentation) Abbreviations Windows® 2000 refers to the Microsoft® Windows® 2000 operating system. Windows® XP refers to the Microsoft® Windows® XP operating system. Windows Vista® refers to the Microsoft® Windows Vista® operating system. Trademarks · · · · · Microsoft, Windows, Windows Vista, DirectX, and PowerPoint are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. IBM and AT are trademarks of International Business Machines Corporation in the United States, other countries, or both. Intel and Pentium are trademarks or registered trademarks of Intel Corporation in the United States and other countries. Adobe and Reader are either registered trademarks or trademarks of Adobe Systems Incorporated in the United States and/or other countries. All other trademarks identified herein are the property of their respective owners. Operating Instructions (For Basic Operations) 3 Introduction Federal Communications Commission Requirements For United States Only Note This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. FCC Warning To assure continued FCC compliance, the user must use only the provided power supply cord. Also, any unauthorized changes or modifications to this equipment would void the user's authority to operate this device. Warning about saving data When the system storage device or any of its optional storage device is adversely effected by operational errors, static electricity, electrical noise, vibration, dust or when the power has been cut off due to malfunction, repair or inadvertently, the memory contents may be lost or changed. Before operating the system, make a point of reading the precautionary notes in the Operating Instructions and the help information, and observe them during operation. Please observe carefully the following precaution: · Make absolutely sure that all important data is saved by back-up or the original is saved. The manufacturer hereby declares that it cannot be held accountable for any loss or change in any data stored on floppy disks, hard disks, optical disks, or other memory devices. System Requirements Computer CPU Operating System Interface Memory (RAM) Hard Disk IBM® PC/AT® or compatible with a CD-ROM drive Intel® Pentium® II processor or later Windows 2000 SP4 / Windows XP / Windows Vista USB 2.0 128 MB or greater (Windows 2000 SP4) 256 MB or greater (Windows XP) 512 MB or greater (Windows Vista) Hard disk with at least 200 MB of free space (not including the space required for saving images) 4 Operating Instructions (For Basic Operations) Introduction Note · · To run the elite Panaboard software, Microsoft .NET Framework 1.1 or later and DirectX® 7.0 or later are required. When you install the elite Panaboard software on the CD-ROM, .NET Framework 1.1 will be installed on your computer if it is not already installed. The system requirements above do not meet the recommended specifications of all operating systems. Exemption of Liability Panasonic Communications Co., Ltd. is not responsible for accidents or injuries caused by, but not limited to, the following: 1. Altering the device or improper installation construction. 2. Using the device for purposes beyond its intended use. 3. Earthquake, fire, flood, tidal wave, hurricane, lightning or other natural phenomena. 4. Natural aging of the building or similar phenomena. 1 For FRG Users (For Germany Only) Note Machine noise information regulation - 3.GPSGV, the maximum sound pressure level is 70 dB(A) or less, in conformity with EN ISO 7779. This equipment is not for use at video display work stations according to BildscharbV. Operating Instructions (For Basic Operations) 5 Table of Contents For Your Safety ........................................................................................7 For Your Safety ...............................................................................................................7 For Users .........................................................................................................................7 Safety Information (For United Kingdom Only) .........................................................10 Precautions ...................................................................................................................10 Usage ......................................................................................................11 Included Accessories ..................................................................................................11 Names and Uses of the Parts ......................................................................................12 Connecting External Components .............................................................................15 Installing the elite Panaboard software ......................................................................17 Setting the Projector ....................................................................................................18 Setting Your System (Calibration) ..............................................................................19 Starting the elite Panaboard software and Performing Calibration ........................20 Uninstalling the elite Panaboard software .................................................................21 Viewing the Electronic Documentation ......................................................................22 Appendix .................................................................................................23 Daily Care ......................................................................................................................23 Cleaning the elite Panaboard .........................................................................................23 Replacing the Battery in the Electronic Pen ...................................................................23 Replacing the Penpoint of the Electronic Pen ................................................................24 Troubleshooting ...........................................................................................................25 Specifications ...............................................................................................................27 Optional Devices and Accessories .................................................................................28 Installation Manual .................................................................................29 Installation Manual (for qualified service personnel) ...............................................29 For Your Safety .............................................................................................................29 Notice .............................................................................................................................29 Included Accessories ..................................................................................................31 Wall Mounting Construction .......................................................................................33 Checking the Wall ..........................................................................................................33 Installing the Wall Mounting Plates ................................................................................34 Wall Types and Installation Procedures .........................................................................35 Stand Assembly (Sold Separately) .............................................................................37 Included Parts ................................................................................................................37 Assembly Instructions ....................................................................................................38 Assembly Instructions .................................................................................................41 Preparing for Removing the elite Panaboard from Its Packaging ..................................41 Assembling the elite Panaboard .....................................................................................42 Confirming the elite Panaboard Operation ................................................................46 Confirming the Interactive Features ...............................................................................46 Repackaging .................................................................................................................47 6 Operating Instructions (For Basic Operations) For Your Safety For Your Safety For Your Safety To prevent severe injury and loss of life, read this section carefully before using the unit to ensure proper and safe operation of your unit. The following graphic symbols are used in this Operating Instructions manual. Denotes a potential hazard that could result in serious injury or death. Denotes hazards that could result in minor injury or damage to the unit. When you operate this product, the power outlet should be near the product and easily accessible. To ensure safe operation the power cord supplied must be inserted into a standard three-prong AC outlet which is effectively grounded (earthed) through the normal wiring. The fact that the equipment operates satisfactorily does not imply that the power point is grounded (earthed) and that the installation is completely safe. For your safety, if in any doubt about the effective grounding (earthing) of the power point, consult a qualified electrician. If the plug cannot be inserted into the AC outlet, contact a licensed electrician to replace the AC outlet with a properly grounded (earthed) one. Do not defeat the purpose of the grounding (earthing) plug (ex. do not use a conversion plug). WARNING CAUTION 1 These symbols are used to alert operators to a specific operating procedure that must not be performed. These symbols are used to alert operators to a specific operating procedure that must be emphasized in order to operate the unit safely. For Users Plug the power cord firmly into an AC outlet. Otherwise, it can cause fire or electric shock. WARNING Power and Ground Connection The power source voltage of this unit is listed on the nameplate. Only plug the unit into an AC outlet with the proper voltage. If you use a cord with an unspecified current rating, the unit or plug may emit smoke or become hot to the touch. Do not pull, bend, rest objects on, or chafe the power cord and plug. Damage to the power cord or plug can cause fire or electric shock. Do not attempt to repair the power cord or plug. If the power cord or plug is damaged or frayed, contact an authorized service representative for a replacement. Operating Instructions (For Basic Operations) 7 For Your Safety Ensure that the plug connection is free of dust. In a damp environment, a contaminated connector can draw a significant amount of current that can generate heat and eventually cause fire if left unattended over an extended period of time. Never touch the plug with wet hands. Danger of electric shock exists. Operating Safeguards If metal fragments or water gets into the unit, turn the unit off and unplug the unit immediately. Contact your dealer for service. Operating the contaminated unit can cause fire or electric shock. Never open or remove unit covers that are screwed with screws unless specifically instructed in the "Operating Instructions". A high-voltage component can cause electric shock. Do not alter the unit or modify any parts. Alteration or modification can cause fire or electric shock. Stop operation immediately if your unit emits smoke, excessive heat, abnormal smell or unusual noise. These conditions can cause fire or electric shock. Immediately turn the unit off and unplug the power cord, and contact your dealer for service. When disconnecting the unit, grasp the plug instead of the cord. Pulling on a cord forcibly can damage it and cause fire or electric shock. During thunderstorms, do not touch the unit and plug. It may cause an electric shock. CHOKING HAZARD Keep the penpoint and battery out of reach of children to prevent swallowing. Battery Use only the specified type of battery. Using the incorrect type of battery can result in overheating/burning or leakage of battery acid. Make sure that the battery is installed with the correct polarity as indicated on the battery holder. Incorrectly installed batteries may burst or leak, resulting in injuries. Batteries that seem worn down or damaged should not be used. Using worn down or damaged batteries may result in leaking. Do not charge, short, heat, break or throw in a fire, as it may result in the battery leaking, generating heat, or bursting. Installation and Relocation Have the unit installed, removed and disposed of only by qualified service personnel. When the unit will no longer be used, in order to prevent it from falling, do not leave the unit installed, but remove it. If the unit falls, it can cause injury. 8 Operating Instructions (For Basic Operations) For Your Safety When disposing of the battery, cover the battery contacts with insulation (ex. tape). Direct contact with other batteries may result in leaking, fire, or explosion. Do not solder the battery, as it may result in the battery leaking, generating heat, or bursting. When moving the unit, be sure to unplug the power cord from the AC outlet. If the unit is moved with the power cord attached, it can cause damage to the cord which could result in fire or electric shock. After installing or moving the unit, lock the casters and set the fall-prevention extension legs. 1 CAUTION Power When the unit is not used over an extended period of time, switch it Off and unplug it. If an unused unit is left connected to a power source for a long period, degraded insulation may cause electric shock, current leakage or fire. The unit should be used only with the power cord enclosed with the unit. Locking the casters (Push this side) Push to lock Move this unit with two persons. Otherwise, this unit may fall down and cause injury. Operating Safeguards If the unit is fallen down or damaged, turn the unit off and unplug the power cord. Otherwise, it may cause fire or electric shock. Do not lean against the screen or on the cover (lower), even if the unit is mounted on the wall. Installation and Relocation Do not position the unit in a location where it is unstable. Do not place the unit in a hot humid or dusty environment. Prolonged exposure to these adverse conditions may cause fire or electric shock. To prevent fire or shock hazard, do not expose this unit to rain or any type of moisture. Battery When the unit is not used over an extended period of time, take the batteries out of the unit. Otherwise, the batteries may leak. Do not use the leaked batteries. Operating Instructions (For Basic Operations) 9 For Your Safety Safety Information (For United Kingdom Only) This appliance is supplied with a moulded three pin mains plug for your safety and convenience. A 5 amp. fuse is fitted in this plug. Should the fuse need to be replaced please ensure that the replacement fuse has a rating of 5 amps. and that it is approved by ASTA or BSI to BS1362. Check for the ASTA mark or the BSI mark on the body of the fuse. If the plug contains a removable fuse cover you must ensure that it is refitted when the fuse is replaced. If you lose the fuse cover the plug must not be used until a replacement cover is obtained. A replacement fuse cover can be purchased from your local Panasonic Dealer. If the fitted moulded plug is unsuitable for the socket outlet in your home then the fuse should be removed and the plug cut off and disposed of safely. There is a danger of severe electrical shock if the cut off plug is inserted into any 13 amp. socket. If a new plug is to be fitted please observe the wiring code as shown below. If in any doubt please consult a qualified electrician. WARNING: This appliance must be earthed. How to replace the fuse: Open the fuse compartment with a screwdriver and replace the fuse. Precautions About Using the Battery If a battery is used improperly, the battery may leak, causing corrosion of the unit, or it may burst. To prevent this, always follow the precaution given below. · If the electronic pen ceases to function because the battery has run out, remove it immediately and dispose of it according to local regulations. Leaving a drained battery in the electronic pen may result in leakage. About Disposing of the Battery For Brazil Após o uso as pilhas / baterias contidas neste produto poderão ser dispostas em lixo doméstico. IMPORTANT: The wires in this mains lead are coloured in accordance with the following code. Green-and Yellow: Earth Blue: Brown: Neutral Live For Netherlands As the colours of the wire in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows. The wire which is coloured Green-and-Yellow must be connected to the terminal in the plug which is marked with the letter E or by the Earth symbol or coloured Green or Green-and-Yellow. The wire which is coloured Blue must be connected to the terminal in the plug which is marked with the letter N or coloured Black. The wire which is coloured Brown must be connected to the terminal in the plug which is marked with the letter L or coloured Red. NL Niet weggooien, maar inleveren als KCA. Bij dit produkt zijn batterijen geleverd. Wanneer deze leeg ziju, moet u ze niet weggooien maar inleveren als KCA. For Taiwan 10 Operating Instructions (For Basic Operations) Usage Usage Included Accessories Check that all of the following items are included with your elite Panaboard. In the event that an item is missing, please contact your dealer. List of Accessories Power Cord (3 m [9 ft. 10 3/8 in.]) 1 USB Cable (5 m [16 ft. 5 3/8in.]) 1 Software CD-ROM 1 1 AAA Battery (LR03) (Disposable) 1 Electronic Pen 1 Penpoint (Replacement) 2 Operating Instructions (For Basic Operations) (this document) 1 Warranty 1 Note · · · The illustration of the power cord shown above is for the United States. The shape of the plug may vary depending on country/area. Stand is sold separately. Store the extra penpoint along with this operating manual. About Using the CD-ROM To prevent damage to the CD-ROM: · Do not touch or write on the surface of the disc. · Do not leave the disc out of the protective case. · Do not leave the disc in the direct sunlight or near heat sources. · Do not place heavy objects on the disc case or drop the case. · To clean the disc, hold the disc by its edges and wipe it from the center to the edges with a dry, soft cloth. Operating Instructions (For Basic Operations) 11 Usage Names and Uses of the Parts Screen Front View Position Sensor Detects the position of the electronic pen. Do not block the sensor while operating the elite Panaboard. Screen Board Project the contents of a computer screen using a projector. Power Switch Pen Tray Push the center of the door to open the pen tray, which can hold up to 2 electronic pens. Status LEDs Left: Power LED (green) Lights green when the power is on. Right: Error LED (red) Lights red when an error occurs. USB Port Directly connect a computer using a USB cable (included). Rear View AC Inlet Power Cord 12 Operating Instructions (For Basic Operations) Usage Notice · The elite Panaboard is designed exclusively for projector images. Do not write on the screen board with a white-board marker. If you write on the screen board with a white-board marker, you cannot erase it with a standard eraser. Use a commercially available melamine foam eraser to erase. Electronic Pen Penpoint When you push down on the penpoint, ultrasonic waves and infrared signals are transmitted, and equivalent of a left mouse click is performed. 1 Ultrasonic Emitter Do not block this area with your fingers. Doing so will prevent the elite Panaboard from correctly detecting the electronic pen's position. Infrared Emitter Do not block this area with your fingers. Doing so will prevent the elite Panaboard from correctly detecting the electronic pen's position. Pen Button Performs the same function as a right-click with a mouse. Battery Cover Notice · · · Note Use the electronic pen by holding it at a right angle to the screen board. Holding it at an angle can cause its position to be read incorrectly. Do not use multiple pens at the same time. This can result in erroneous operation. Do not push the penpoint while holding the pen close to the elite Panaboard. Doing so can cause erroneous behavior. · · · The electronic pen switches to power-save mode after about 30 minutes. When waking up the pen from power-save mode by pushing the penpoint, the pen's reaction may be slow. When operating the electronic pen, you will hear a buzzing sound due to the pen emitting ultrasonic waves for location detection. This sound does not have any negative effects for nearby people or devices. It will not cause electrical shocks. Operating Instructions (For Basic Operations) 13 Usage Inserting (Exchanging) Batteries 1. Remove (replace) the battery cover. 2. Insert (exchange) the battery and replace the cover. · When replacing the cover, follow the procedure in reverse. · Make sure to use a AAA alkaline battery, and ensure that and face the correct directions. 14 Operating Instructions (For Basic Operations) Usage Connecting External Components 1. Set the power switch to "O" (OFF), connect the power cord (included) to the elite Panaboard, and plug the power cord into an AC outlet. Rear Power Switch (ON) (OFF) 1 Power Cord (Included) Power Cord · · Plug the power cord into an outlet that is close to the elite Panaboard and in a location that is easy to unplug. If you are using the optional stand, plug the power cord into the AC inlet, and secure the cord as shown in the illustrations below. When attaching the power cord downward. When attaching the power cord along the lower side of the elite Panaboard. · · About Grounding If you cannot connect the grounding line, contact your dealer. The cost of installing a grounding connection is not included in the price of the elite Panaboard. The included power cord is exclusively for use with the elite Panaboard. Do not use it with any other devices. Operating Instructions (For Basic Operations) 15 Usage 2. Connect the elite Panaboard to a computer using the USB cable (included). · elite Panaboard: Plug the B connector (smaller connector) into the elite Panaboard's USB port. · Computer: Plug the A connector (larger connector) into a USB port on the computer. Do not connect the elite Panaboard via a USB hub. This could result in erroneous operation. To USB Port USB Cable (Included) Computer AC Video Cable Projector AC 3. Connect the computer to a projector. · For instructions on connecting your computer and projector, refer to the respecting instruction manuals. About the Usage Location · · Do not place the elite Panaboard where it is directly exposed to sunlight, near a stove, near to a heating/ cooling vent or exposed to strong winds. Do not use the elite Panaboard in a location less than 10 °C (50 °F) or in a location subject to extreme changes in temperature. Note · If you use the elite Panaboard under the conditions above, there is a risk that the elite Panaboard will not operate correctly. Moving the elite Panaboard When Using the Stand (Sold Separately) 1. Make sure that the power switch is set to "O" (OFF), and disconnect the power cord and USB cable. 2. Release the locks on the casters. 3. Move the elite Panaboard, taking care not to bang or shake it. Notice · · Always move the elite Panaboard with 2 people. Do not drag or step on the cable. 4. Lock the casters. 16 Operating Instructions (For Basic Operations) Usage Installing the elite Panaboard software You need to install the elite Panaboard software on the computer that will be used with the elite Panaboard. To install the elite Panaboard software, follow the procedure below. Notice 5. If you agree to the terms in the "License Agreement", click [Yes]. · In Windows Vista, if the "User Account Control" window is displayed, click [Continue] to continue with the installation. 6. When the following screen is displayed, confirm that the USB cable is not connected to your computer or the elite Panaboard, and click [OK]. · If the USB cable is connected to the elite Panaboard, disconnect the cable, and click [OK]. · If .NET Framework 1.1 or later is not installed, an installation screen will be displayed. Follow the on-screen directions to install these components. · · Do not connect the USB cable until the installation is completed. Do not connect more than 1 elite Panaboard to the same computer. (Doing so can cause erroneous behavior on the computer.) 1 1. Turn on your computer and start the Windows*1 operating system. · Log into an account with Administrator privileges. *1 Windows refers to the Microsoft® Windows® operating system. 2. Insert the included CD-ROM into the CD-ROM drive. · The setup screen will be displayed. · If the setup screen does not appear, select your CD-ROM drive in Explorer and double-click "Menu.exe". · In Windows Vista, if the Autoplay dialog box is displayed, click [Run Menu.exe]. 3. When the "Welcome" screen has been displayed, click [Next]. 4. Click [Install elite Panaboard]. 7. When the installation wizard is displayed, follow the on-screen instructions and continue with the installation. 8. When installation has finished, click [Finish]. · Restart your computer if you are prompted to do so. · The group [elite Panaboard] will be created in the [Panasonic] group in the program menu. · The following items will appear in the [elite Panaboard] group: ­ elite Panaboard software ­ elite Panaboard book ­ Operating Instructions for Basic Operations ­ Operating Instructions for Software Operating Instructions (For Basic Operations) 17 Usage Setting the Projector Set up your projector as instructed below. About Positioning the Image · When you are projecting an image, make sure that the edge of the projected image is at least 5 mm (1/4 in.) from the screen frame. The electronic pen may not function correctly within 50 mm (2 in.) of the position sensor in the upper-left corner of the screen board. 50 mm (2 in.) 5 mm (1/4 in.) Projectable Area 5 mm (1/4 in.) 5 mm (1/4 in.) Project the Image as a Rectangle · Adjust the location of the projector to project at a right angle with the elite Panaboard. · If the image is projected trapezoidally, the position of the electronic pen may not be read correctly. Adjust the projector so that the projected image is a rectangle. Refer to your projector's documentation for information on adjusting the projected image. 18 Operating Instructions (For Basic Operations) Usage Set the Proper Resolution · Set your computer's and projector's resolutions to the most appropriate setting. If the resolution is not set properly, the image will be difficult to see. Particularly, if the projector's resolution is lower than the computer's, thin lines can appear cut or broken. Refer to your projector's documentation for information on adjusting the resolution. Setting Your System (Calibration) About Calibration Calibration is setting up the elite Panaboard and projector so that lines and comments drawn on the screen board with the electronic pen will be correctly displayed on the image projected onto the screen board. Be sure to perform calibration before use. After you have set up the elite Panaboard, project an image onto the screen board and use the elite Panaboard software installed on your computer to perform calibration. Do Not Look Directly into the Projector Lamp · When using a projector, try to avoid looking directly into the projector lamp. Doing so can hurt your eyes. 1 After Calibration Do Not Move the elite Panaboard or the Projector · The position of projected image and electronic pen will become misaligned in the following cases, requiring you to re-calibrate their positions. ­ The location of the projector changed. ­ The location of the elite Panaboard changed. ­ The image area or placement was changed due to changes in the zoom, focus, etc. ­ The resolution of the projector or the computer changed. If you are using the elite Panaboard installed on a stand, be aware that accidentally hitting the elite Panaboard or pushing too strongly with the electronic pen while operating. Doing so can move the stand's position, which will result in misalignment of the projected image and the electronic pen's position. Make sure to lock the stand's casters when using the elite Panaboard, as failing to do so can cause misalignment. · · Operating Instructions (For Basic Operations) 19 Usage Starting the elite Panaboard software and Performing Calibration 1. Turn on the elite Panaboard. 2. Connect the elite Panaboard to your computer with the USB cable. · The elite Panaboard software starts automatically. · When you start the elite Panaboard software for the first time, the calibration screen is displayed. · Restart your computer if you are prompted to do so. After the computer has restarted, connect the elite Panaboard to your computer with the USB cable. 3. Perform calibration. 4. Press the electronic pen in the center of the 4 points in each corners of the display for 2 seconds, in the order shown in the illustration. 1 2 Hold and press the electronic pen at a right angle to the screen board. · When you push down on the penpoint, the electronic pen will make a buzzing sound. · When the position of the indicated point has been determined correctly, calibration will automatically move to the next point. · When calibration has finished normally, a completion dialog box will be displayed. 5. Click [OK]. · If the elite Panaboard and projector are fixed so that they will not move, select the [Always use this calibration information.] check box, and click [OK] to skip calibration from the next time you start the elite Panaboard software. icon will · After calibration has completed, the be displayed in the notification area, and the Desktop Drawing Tool is automatically displayed. · 4 3 · [Desktop Drawing Tool] You will be able to use elite Panaboard software. 20 Operating Instructions (For Basic Operations) Usage Note · For detailed information about using the elite Panaboard software, refer to the included electronic manual or the help. For instructions on viewing the electronic documentation "Operating Instructions (For Software)", see "Viewing the Electronic Documentation" (page 22). Uninstalling the elite Panaboard software If it is necessary to uninstall the elite Panaboard software, follow the procedure below. 1. Turn on your computer and start Windows. · Log into an account with Administrator privileges. 2. Select [Add or Remove Programs] from the Control Panel. · In Windows 2000, select [Add/Remove Programs]. · In Windows Vista, select [Uninstall a program]. 3. Select Panasonic elite Panaboard, then remove it. 4. Follow the on-screen instructions. 5. When uninstallation is complete, restart your computer. Exiting the elite Panaboard software Right-click on the icon in the notification area, and select [Exit] from the menu. 1 Operating Instructions (For Basic Operations) 21 Usage Viewing the Electronic Documentation Follow the procedure below to view the electronic documentation "Operating Instructions (For Software)". 1. Turn on your computer and start Windows. 2. Open "Operating Instructions (For Software)" from the Start menu. ([Start] ® [All Programs] ® [Panasonic] ® [elite Panaboard] ® [Operating Instructions for Software]) · The electronic documentation will be displayed. Note · To view the electronic documentation, you must have Adobe® Reader® installed on your computer. If your computer is connected to the Internet, you can download Adobe Reader from Adobe's web site. 22 Operating Instructions (For Basic Operations) Appendix Appendix Daily Care When cleaning the elite Panaboard or inside the elite Panaboard, make sure to switch off the power and unplug the power cord from the AC outlet. Cleaning the elite Panaboard Replacing the Battery in the Electronic Pen When the charge in the battery in the electronic pen is low, the message, "The pen battery is low. Replace the battery soon." will be displayed on the computer screen. Continued use of the electronic pen can lead to poor performance. Replace the battery as soon as possible. See "Inserting (Exchanging) Batteries" (page 14) for details on replacing the battery. · Promptly remove used batteries and properly dispose of them following your local laws and regulations. 1 For Brazil Após o uso as pilhas / baterias contidas neste produto poderão ser dispostas em lixo doméstico. Gently wipe the elite Panaboard with a soft, moist cloth. Notice · · · · For spots that are difficult to remove, use commercially available white-board cleaner or neutral household cleaner diluted with water. The elite Panaboard is designed exclusively for projector images. If you write on the screen board with a white-board marker, you cannot erase it with a standard eraser. Use a commercially available melamine foam eraser to erase. Do not wipe the screen board with a dry cloth. (Doing so can cause static electricity build-up.) Do not use thinner, benzene, or abrasive chemicals to clean. (Doing so can result in discoloration.) For Netherlands NL Niet weggooien, maar inleveren als KCA. Bij dit produkt zijn batterijen geleverd. Wanneer deze leeg ziju, moet u ze niet weggooien maar inleveren als KCA. For Taiwan Operating Instructions (For Basic Operations) 23 Appendix Replacing the Penpoint of the Electronic Pen As the penpoint of the electronic pen becomes worn, a hole will appear in the penpoint. Continuing to use the electronic pen in this condition can cause damage to the screen or unsatisfactory operation, so replace the penpoint with a new one. 24 Operating Instructions (For Basic Operations) Appendix Troubleshooting When you think there may be a problem, follow the steps in the table below. If the problem persists, contact your dealer. Symptom Possible cause and solution See page ­ The LEDs do not light when Check that the power cord is properly plugged in. the power switch is turned If the problem persists, turn off the power, and then turn it on on. again. Red LED is blinking. Turn off the power, and turn it on again. If the problem persists, contact your dealer. ­ · The USB cable is connected to a USB hub. The computer does not rec- Do not connect the elite Panaboard through a USB hub. ognize the elite Panaboard. · Check that the elite Panaboard is in an operable state, and that the USB cable is properly connected. The connection between the computer and the elite Check that the elite Panaboard is in an operable state, and that the Panaboard is unexpectedly USB cable is properly connected. lost. The electronic pen's position is not correct. The projected image is misaligned. Perform the calibration again. 1 ­ ­ 20 You are holding the electronic pen at an angle. You are operating the elite Panaboard in direct sunlight or other strong lighting. · Infrared controllers (e.g., a television remote control) are being used and pointed towards the position sensor. · There is a wall or ceiling close to the sides of the elite Panaboard. Drawn lines and comments · There is an air-conditioner vent close to the elite Panaboard. are not completely dis· A plasma television is being used close to the elite Panaboard. played or are displayed in · Part of the position sensor is blocked. the wrong location. · You are covering part of the electronic pen's sensor with your hand. · Several electronic pens are being used at the same time. · The electronic pen is low on batteries. Check that none of the above is causing the problem. If misalignment is not caused by any of the above, perform the calibration again. Apart from writing directly on the elite Panaboard with the electronic Extra lines are displayed on pen, you pushed the penpoint with your finger while holding it close to the elite Panaboard. the computer screen. Avoid pushing the penpoint with your finger. · · ­ ­ Operating Instructions (For Basic Operations) 25 Appendix Symptom Possible cause and solution See page 14 23 The message "The pen battery is low. Replace the batReplace the electronic pen's battery with a new one. tery soon." is displayed on the computer screen. Marks written with a white- Because the elite Panaboard is designed exclusively for projector images, you cannot erase the marks with a standard eraser. board marker cannot be erased. Use a commercially available melamine foam eraser to erase. 23 26 Operating Instructions (For Basic Operations) Appendix Specifications Model Number General Power Power Consumption: During Operation UB-T780 AC 100 V­240 V, 50 Hz/60 Hz 0.1 A External Dimensions: Height × 1340 mm × 1752 mm × 89 mm Width × Depth (4 ft. 4 7/8 in. × 5 ft. 9 1/8 in. × 3 1/2 in.) Weight Operating Environment Storage Environment Interface Input Unit Interactive Features Screen Board Size: Height × Width Effective Area: Height × Width 26 kg (57.32 lbs) Temperature: 15 °C to 30 °C (59 °F to 86 °F) Humidity: 30 % to 80 % Temperature: -20 °C to 40 °C (-4 °F to 104 °F) Humidity: 15 % to 80 % USB 2.0 1175 mm × 1692 mm (3 ft. 10 3/8 in. × 5 ft. 6 3/4 in.) 1165 mm × 1502 mm (3 ft. 10 in. × 4 ft. 11 1/4 in.) Project the image so that it is at least 5 mm (1/4 in.) from the screen frame. The electronic pen may not function correctly within 50 mm (2 in.) of the position sensor in the upper-left corner of the screen board. 50 mm (2 in.) 5 mm (1/4 in.) 1 Projectable Area 5 mm (1/4 in.) 5 mm (1/4 in.) Electronic Pen Power Electronic Pen Battery Life LR03 (AAA alkaline dry cell battery) × 1 30 hours (when used continuously at 25 °C [77 °F]) * When using Panasonic LR03 alkaline dry-cell batteries. Operating Instructions (For Basic Operations) 27 Appendix Optional Devices and Accessories Optional Device Accessories Stand Electronic Pen KX-B061 UE-608025 · To purchase separately sold items, contact your dealer. 28 Operating Instructions (For Basic Operations) Installation Manual Installation Manual Installation Manual (for qualified service personnel) · · · Request assembly of the Electronic Board, stand and wall mounting from your dealer. Before assembly and construction, read this section thoroughly. When installing the elite Panaboard on a wall or on the stand, perform installation with 2 people. For Your Safety To prevent severe injury and loss of life, read this section carefully before using the unit to ensure proper and safe operation of your unit. The following graphic symbols are used in this Installation Manual. Denotes a potential hazard that could result in serious injury or death. Denotes hazards that could result in minor injury or damage to the unit. Notice WARNING Safety check must be done by qualified service personnel after installing this option. 1 WARNING CAUTION Be sure to disconnect the power cord while installing the unit. Otherwise, it may cause electric shock or injury. Be sure to use the specified parts for the installation. Otherwise, it may cause fire, electric shock or injury. These symbols are used to alert operators to a specific operating procedure that must not be performed. These symbols are used to alert operators to a specific operating procedure that must be emphasized in order to operate the unit safely. Notes in the operating instructions or notes of labels on the cabinet, chassis or parts should be observed. Do not alter the unit and install. Installing an altered unit can cause fire, electric shock or injury. Have the unit installed, removed and disposed of only by qualified service personnel. Operating Instructions (For Basic Operations) 29 Installation Manual CAUTION After installing or moving the electronic board, lock the casters and set the fallprevention extension legs. Locking the casters (Push this side) Push to lock If the unit is hung on a wall, confirm the wall must be capable of supporting at least the following weight. 1,005 N [103kgf (227 lbs)] Do not attach the electronic board to mortared walls. Accidental electric leakage from the wall mounting plate bolts to metal laths or wire laths can cause heat, smoke or a fire. Confirm the bolts of the unit are certainly caught by the wall mounting plate by pulling the unit after hanging the unit on the wall mounting plate if the unit is mounted on a wall. Be sure to put on a glove to avoid electric shock or injury. 30 Operating Instructions (For Basic Operations) Installation Manual Included Accessories Confirm that the following items are included with the elite Panaboard. No. Part Name Illustration Q'ty Remarks The illustration of the power cord is for the United States. The shape of the plug may vary depending on country/area. For computer connection Operating Instructions (For Software) Drivers Application software For power cord Power Cord (3 m [9 ft. 10 3/8 in.]) 1 USB Cable (5 m [16 ft. 5 3/8 in.]) 1 1 CD-ROM 1 Cable Holder 1 Wall Mounting Plate (Left) 1 -- Wall Mounting Plate (Right) Battery (LR03 AAA alkaline battery) 1 -- 1 For electronic pen Electronic Pen 1 -- Penpoint (Replacement) Cable Tie 2 1 For electronic pen Fastener for power cord when mounted on a wall Operating Instructions (For Basic Operations) (includes Installation Manual) May not be included depending on country/area. Operating Instructions 1 Warranty 1 Operating Instructions (For Basic Operations) 31 Installation Manual Notice ·