Installation and Assembly - Universal Adapter Bracket for 32" - 60" Flat Panel Screens IMPORTANT! Read instruction sheet before you start installation and assembly. Models: PLP UNL, PLP UNL-S, PLP UNLP, PLP UNLP-S Before you begin, make sure all parts shown are included with your product. Parts List AA BB CC DD Description adapter bracket shallow adapter bracket deep adapter bracket security allen wrench Qty 1 2 2 1 PLP-UNL Part # 200-1950 200-0756 200-0752 560-1146 PLP-UNL-S Part # 200-4950 200-0757 200-0753 560-1146 PLP-UNLP Part # 200-1950 200-0754 200-0750 n/a PLP-UNLP-S Part # 200-4950 200-0755 200-0751 n/a BB AA CC DD 1 of 4 ISSUED: 11-11-05 SHEET #: 202-9060-1 Security Adapter Bracket Fasteners M4 x 12 mm (6) 510-1079 M5 x 12 mm (4) 520-1064 M6 x 12 mm (4) 520-1050 M8 x 15 mm (6) 520-1068 M6 x 20 mm (4) 520-9554 M5 x 25 mm (4) 520-1122 M4 x 25 mm (4) 510-1082 M6 x 30 mm (4) 520-1067 M6 x 25 mm (4) 520-1211 M8 x 25 mm (4) 520-1101 M8 x 40 mm (4) 520-1152 multi-washer (6) 580-1036 I.D. 5.6 mm (4) 540-1057 I.D. 8.7 mm (4) 540-1059 Phillips Adapter Bracket Fasteners M4 x 12 mm (6) 504-9013 M5 x 12 mm (4) 520-1027 M6 x 12 mm (4) 520-1128 M8 x 16 mm (6) 520-9257 M6 x 20 mm (4) 520-9402 M5 x 25 mm (4) 520-9543 M4 x 25 mm (4) 504-1015 M6 x 30 mm (4) 510-9109 M6 x 25 mm (4) 520-1208 M8 x 25 mm (4) 520-1031 M8 x 40 mm (4) 520-1136 multi-washer (6) 580-1036 I.D. 5.6 mm (4) 540-1057 I.D. 8.7 mm (4) 540-1059 2 of 4 ISSUED: 11-11-05 SHEET #: 202-9060-1 Installing Adapter Brackets Refer to Screen Compatibility Chart to determine the proper fasteners to use. 1 To prevent scratching the screen, set a cloth on a flat, level surface that will support the weight of the screen. Place screen face side down. If screen has knobs on the back, remove them to allow the adapter brackets to be attached. Place adapter brackets (BB or CC) on back of screen, align to holes, and center on back of screen as shown in figure 1.1. Attach the adapter brackets to the back of the screen using the appropriate combination of screws, multiwashers, and spacers as shown in figure 1.3. Note: Top and bottom holes must always be used. Verify that all holes are properly aligned, and then tighten screws using a phillips screwdriver. Note: If using security screws, tighten using security allen wrench (DD). X WARNING · Tighten screws so adapter brackets are firmly attached. Do not tighten with excessive force. Overtightening can cause stress damage to screws, greatly reducing their holding power and possibly causing screw heads to become detached. Tighten to 40 in. · lb (4.5 N.M.) maximum torque. Notes: · The number of fasteners used will vary, depending upon the type of screen. · Multi-washers and spacers may not be used, depending upon the type of screen. · Use the corresponding hole in the multiwasher that matches your screw size as shown in figure 1.2. CENTER BRACKETS VERTICALLY ON BACK OF SCREEN BB or CC X fig 1.1 Note: "X" dimensions should be equal. WARNING · If screws don't get three complete turns in the screen inserts or if screws bottom out and bracket is still not tightly secured, damage may occur to screen or product may fail. MULTI-WASHER MEDIUM HOLE FOR M5 SCREWS SMALL HOLE FOR M4 SCREWS LARGE HOLE FOR M6 SCREWS BB or CC SCREWS MULTIWASHER SPACERS fig. 1.2 fig 1.3 3 of 4 ISSUED: 11-11-05 SHEET #: 202-9060-1 Mounting and Removing Flat Panel Screen Refer to mount instruction sheet for attachment of adapter bracket to mount. 2 Hook adapter brackets (BB or CC) onto adapter bracket (AA). Then slowly swing screen in as shown. Turn screws clockwise at least six times to prevent screen from being removed as shown in detail 1. Note: If using security screws, tighten using security allen wrench (DD). Screen can be adjusted horizontally if desired. Note: To lock the screen down, tighten screws to adapter bracket as shown in detail 1. To remove screen from mount, loosen screws, swing screen away from mount, and lift screen off of mount. WARNING · Always use an assistant or mechanical lifting equipment to safely lift and position the plasma television. BB or CC AA AA SCREWS BB or CC DETAIL 1 © 2005 Peerless Industries, Inc. All rights reserved. Peerless is a registered trademark and Smart mount is a trademark of Peerless Industries, Inc. All other brand and product names are trademarks or registered trademarks of their respective owners. 4 of 4 ISSUED: 11-11-05 SHEET #: 202-9060-1 ...