User manual PHILIPS 107E

Introduction The 107E colour monitor displays sharp images of text and graphics with a maximum resolution up to 1280x1024 pixels. It is optimal for Windows, CAD / CAM / CAE, desktop publishing, spread sheets, multimedia, and any other application which demands large screen size and high resolutions. This monitor automatically scans horizontal frequencies from 30KHz to 70KHz, and vertical frequencies from 50Hz to 130Hz. With microprocessor based digital controlled circuit, the monitor can automatically adjust itself to the video card's scanning frequency and displays an image with precise parameters you desire. The wide range of scanning frequency supports variety of operating platforms, such as IBM PC and compatibles. E N Feature Highlights · On-Screen-Display function provides more informations when the user operates the control functions. This feature provides userfriendliness and ease-of-use when operating the monitor. Anti-Glare and Anti-Static screen coating eliminate any bad effects caused by the screen surface such as reflection of the room lights and dust attraction. Green Design including automatic power saving function (NUTEK) and low emission MPRII compliance shows our commitment in environmental care. DDC1/DDC2B allows communication between the monitor and PC system for optimal video configuration. · · · 1 E N Note: If you experienced your monitor display is changing from color to mono, it's possible that you are using a non-VESA-DDC-standard video card. Please consult with your local PCEC dealer for more information. ENERGY STAR is a U.S. registered mark. As an ENERGY STAR® Partner, PCEC, has determined that this product meets the ENERGY STAR® guidelines for energy efficiency. IBM, IBM PC and Power PC are registered trademarks of International Business Machines Corporation. 2 Safety precautions and maintenance x Disconnect the monitor from the mains supply if the monitor is not to be used for an extended period of time. x Do not attempt to remove the back cover, as you will be exposed to a shock hazard. The back cover should only be removed by qualified service personnel. x Do not place objects on top of the monitor cabinet, which could fall into vents or which could cover them and prevent proper cooling of the monitor's electronic devices. x Do not expose the monitor to rain or excessive moisture to avoid the risk of shock or permanent damage to the set. x Do not use alcohol or ammonia based liquid to clean the monitor. If necessary, clean with a slightly damp cloth. Disconnect the monitor from the mains supply before cleaning. x Consult a service technician if the monitor does not operate normally when operating instructions of this manual are followed. E N Package Your 107E package includes the following items: · · · · · The monitor (integrated with tilt / swivel pedestal) Pedestal Power cord Interface cable (flying-in) Win95 driver disk End of life disposal Your new set contains materials which can be recycled and reused. Specialized companies can recycle your product to increase the amount of reusable materials and to minimize the amount of materials to be disposed of. Please inform yourself on local regulations on disposal of your old set. 3 E N Installation Important: Please refer to the user's manuals of your computer and video adapter to make sure these equipments are properly installed and configured before installing the monitor. Positioning / Ventilation x Avoid exposing the monitor to direct sunlight, stoves or any other heat sources. x To prevent overheating, make sure that the ventilation openings of the monitor are not covered. x Keep moisture and dust away. x Keep away from any magnetic objects, such as speakers, electric motors, transformers, ...etc. x When positioning this monitor, make sure that the mains plug and socket are easily accessible. Pedestal With the built-in pedestal you can tilt and / or swivel the monitor for a most comfortable viewing angle. 107 E EXIT MENU 4 Connection Important: Please make sure the AC power to your computer is "OFF" before connecting or disconnecting any display peripheral. Failure to do so may cause serious personal injury as well as permanent damage to your computer equipments. · Connect the monitor to the computer using the supplied interface cables. Connection with computer system other than IBM PC may need different type of adapters. Please consult your computer supplier for these adapters. Connect the power cord to a wall outlet after the interface cable is properly connected. E N Monitor rear view 1) IBM PC connection 2) Mains connection WARNING:SHOCK HAZARD-DO NOT OPEN AVIS:RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR PRECAUCION RIESGO DE CHOQUE ELECTRICO,NO ABRIR 2 1 5 E N Control locations and functions Monitor control panel EXIT MENU Descriptions of knobs and keypads on front control panel / / · Press this knob to switch ON and OFF of monitor's power · OSD rotary control knob. · Active OSD menu. · Adjust contrast or the display. · Adjust brightness or the display. 6 On-Screen-Display Activating the On-Screen-Display The monitor controls are accessed by pressing button to enable OSD (On-Screen-Display). The main menu will be displayed as follows. E N H:68.8KHz V:85Hz CONTRAST 70 Each Function is selected by highlighting it via the tact key and pressing button to confirm. To exit OSD, highlight press select button . , to select or adjust and While operating Function, please use press button to confirm. Note: If adjustment or selection of any OSD menu is not made for more than 10 seconds, the current setup will be saved and the OSD will disappear automatically. BRIGHTNESS & CONTRAST q Brightness : Adjusts background brightness. H:68.8KHz V:85Hz BRIGHTNESS 70 7 E N q Contrast : Adjusts contrast between foreground and background. H:68.8KHz V:85Hz CONTRAST 70 q EXIT : Save user adjustment and OSD disappear. SIZE & POSITION q Horizontal Size : Adjusts image width. H:68.8KHz V:85Hz H-SIZE A A 70 q Horizontal Position : Moves image left or right. H:68.8KHz V:85Hz H-CENTER A A 70 8 q Vertical Size : Adjusts image height. H:68.8KHz V:85Hz E N V-SIZE A A 70 q Vertical Position : Moves image up or down. H:68.8KHz V:85Hz V-CENTER A A 70 q EXIT : Save user adjustment and OSD disappear. GEOMETRY q Pincushion : Adjusts the amount of curvature on the vertical edges. H:68.8KHz V:85Hz PINCUSHION A A 70 q Trapezoid : Equalizes the length of the top and bottom edges. H:68.8KHz V:85Hz TRAPEZOID A A 70 9 E N q Rotation : Tilts the image clockwise or counter-clockwise. H:68.8KHz V:85Hz ROTATION A A 70 q EXIT : Save user adjustment and OSD disappear. q PIN-BALANCE : Adjust picture curves outwards or inwards. H:68.8KHz V:85Hz PIN BALANCE A A 70 q PARALLEL : Adjust for optimal parallelogram screen picture. H:68.8KHz V:85Hz PARALLELOGRAM A A 70 COLOR TEMPERATURE q 9300°K : Factory preset color temperature of 9300°K. q 6500°K : Factory preset color temperature of 6500°K. H:68.8KHz V:85Hz H:68.8KHz V:85Hz RECALL 9300K COLOR TEMPERATURE RECALL 6500K COLOR TEMPERATURE 10 q User : User set for color temperature then select R, G for adjustment. R : Adjusts red intensity. G : Adjusts green intensity. E N H:68.8KHz V:85Hz EXIT USER COLOR R G 100 100 EXIT USER COLOR R G 100 100 q EXIT : Save user adjustment and OSD disappear. 11 E N SPECIAL q Manual Degauss : Discoloration of the image can be caused by gradual magnetization of the monitor components. This is particularly likely to occur when the monitor is moved or rotated. The monitor may "buzz" momentarily when the user control is selected and the image will change color and wobble for a few seconds. These effects are normal. H:68.8KHz V:85Hz DEGAUSS 70 q Moire Cancellation : Moire effect may be found in some display modes. If this is the case, please use "Moire Cancellation" function to reduce Moire effect. MOIRE REDUCE 100 q EXIT : Save user adjustment and OSD disappear. 12 RECALL FACTORY PRESETS q Recall : Recall brightness and contrast presets. H:68.8KHz V:85Hz E N RECALL 70 q Recall : Recall size and phase presets. q Recall : Recall geometry preset. q EXIT : Save user adjustment and OSD disappear. * Whenever the signal cable is disconnected, the screen will appear a message as below: NO SIGNAL INPUT OR CABLE DISCONNECTED 13 E N Data Storage (A) Factory preset mode: This monitor has 9 factory-preset modes as indicated in the following table: Frequence Resolution H(KHz) V(Hz) 720x400 31.5 70 640x480 31.5 60 640x480 37.5 75 640x480 43.3 85 800x600 46.9 75 800x600 53.7 85 1024x768 60.0 75 1024x768 68.7 85 1280x1024 64.0 60 Sync polarity H V ­ + ­ ­ ­ ­ ­ ­ + + + + + + + + + + M01 M02 M03 M04 M05 M06 M07 M08 M09 Mode VGA VGA VGA VESA SVGA VESA VESA VESA VESA * Does not support sync-on-green. (B) User mode In addition to factory preset modes, the monitor can also provides additional 9 User-defined modes. If the input video signal is different from our factory-preset modes,the new timing data will be automatically stored. However, the displayed parameters may need to be adjusted. User can adjust the parameters via OSD, as preceding procedures which already described on "Adjustment via On-Screen-Display" section. 14 Automatic Power Saving If you have VESA's DPMS compliance display card or software installed in your PC, the monitor can automatically reduce its power consumption when not in use. And if an input from keyboard, mouse or other input devices is detected, the monitor will automatically "wake up". The following table shows the power consumption and signalling of this automatic power saving feature: E N VESA's mode ON Stand-by Suspend OFF Power Management Definition H-sync V-sync Power Power LED used saving(%) color Active Yes Yes < 100W 0% Green Blanked No Yes < 15W 85% Amber Blanked Yes No < 15W 85% Amber Blanked No No < 5W 95% Amber Video This monitor is ENERGY management compatible. STAR ® compliant and power As an ENERGY STAR® Partner, PCEC, has determined that this product meets the ENERGY STAR® guidelines for energy efficiency. 15 E N Specification* (I) General CRT Screen size Dot pitch Phosphor Screen treatment Display area Factory preset Maximum usable Scanning frequency Horizontal (line) Vertical (frame) Input power Power consumption Input signal Video Sync Pedestal Tilt Swivel Physical Unit dimension (WxHxD) Net weight Operating condition Temperature Humidity Storage condition Temperature Humidity White Color Coordinates: Red: x= 0.625 y= 0.340 Green: x= 0.285 y= 0.605 : 17" (43.2 cm) flat & square : 0.28 mm : P22 or equivalent, medium short persistence : Anti-glare, anti-static : 300 mm (H) x 230 mm (V) : 323 mm (H) x 242 mm (V) : : : : 30-70 kHz (AutoScan) 50-130 Hz (AutoScan) 100-240 VAC, 50-60 Hz 85 Watt normal, 100 Watt maximum : 0.7 Vpp, 75 Ohm inpedence : Separate sync. TTL level Composite sync. TTL level : 4.5° forward, 14° backward : 90° leftward, 90° rightward : 410 x 408 x 430 (mm) : 16 kg : 0° C - 40° C : 20% - 80% : -25° C - 70° C : 10% - 95% Blue: x= 0.150 y= 0.065 * Because of a policy of continuous product improvement, the above specifications are subjected to change without notice. 16 (II) Pin assignment: E N 1 6 11 5 10 15 The 15-pin D-sub connector (male) of the signal cable (IBM systems): Pin No. 1 2 3 4 5 6 7 8 Assignment Red video input Green video input Blue video input Ground Identical output - Connected to pin 10 Red video ground Green video ground Blue video ground Pin No. 9 10 11 12 13 14 15 Assignment No pin Self-test Ground Serial data line (SDA) H. Sync / H+V V. Sync (VCLK for DDC) Data clock line (SDA) 17 E N 17E4222E Digital AutoScan Colour Monitor Contents English Introduction Feature Highlights Safety precautions and maintenance Package End of life disposal Installation Connection Control locations and functions On-Screen-Display Data Storage Automatic Power Saving Specification .... 1 .... 1 .... 3 .... 3 .... 3 .... 4 .... 5 .... 6 .... 7 .... 14 .... 15 .... 16 18 OTHER LANGUAGE VERSIONS FRENCH(FRANCAIS) .... 18 E N Appendix English Information for Users in the U.S. FCC Declaration WARRANTY Deutsch Hinweis / GS / ACHTUNG Français FCC Declaration ........ A1 ........ A2 ........ A5 ........ A3 ........ A4 19