3 ENGLISH 4 DEUTSCH 15 FRANÇAIS 27 NEDERLANDS 39 ESPAÑOL 51 ITALIANO 63 PORTUGUÊS 75 TÜRKÇE 87 107 HQ7870 4 ENGLISH Important Read these instructions for use carefully before using the appliance and save them for future reference. Only use the powerplug supplied to charge the appliance. The powerplug transforms 100-240 volts to a safe low voltage of less than 24 volts. Only use the powerplug that comes with the appliance to guarantee safe transformation. The powerplug contains a transformer. Do not cut off the powerplug to replace it with another plug, as this will cause a hazardous situation. If the powerplug is damaged, always have it replaced by one of the original type in order to avoid a hazard. Make sure the powerplug does not get wet. Charge, store and use the appliance at a temperature between 5cC and 35cC. Do not recharge the shaver in a closed pouch. The appliance complies with the internationally approved IEC safety regulations and can be safely cleaned under the tap. Be careful with hot water. Always check if the water is not too hot, to prevent your hands from getting burnt. Always unplug the shaver before cleaning it under the tap. C C ENGLISH 5 Charging When you charge the shaver for the first time or after a long period of disuse, leave it to charge continuously for 4 hours. Charging normally takes approx. 1 hour. Do not leave the appliance connected to the mains for more than 24 hours. You can also shave without charging by connecting the shaver to the mains. Charge indications Charging C When you are charging the empty shaver, the bottom pilot light burns red.When the batteries contain sufficient power for one shave, the bottom pilot light starts to blink green. As charging continues, more and more green pilot lights go on to indicate to what level the batteries have been charged. Batteries fully charged have been C When the batteries are on. fully charged, all green pilot lights 6 ENGLISH Remaining capacity of the batteries C The amount thepower leftofinpilot lights thatis indicated by number are on. As the amount of power decreases, the lights gradually go out one after the other. Batteries running low C When the batteries are running low, theswitch bottom pilot light turns red.When you the shaver off, the red light blinks for 4 seconds. Charging the appliance Do not recharge the shaver in a closed pouch. C 1 2 3 Put the appliance plug in the shaver. Put the powerplug in the wall socket. Remove the powerplug from the wall socket and pull the appliance plug out of the shaver when the batteries have been fully charged. Cordless shaving time A fully charged shaver has a cordless shaving time of up to 70 minutes. ENGLISH 7 Using the appliance Shaving 1 Switch the shaver on by pressing the on/off button once. C Move the shaving heads quickly over your skin, making both straight and circular movements. Shaving on a dry face gives the best results. Your skin may need 2 or 3 weeks to get accustomed to the Philishave system. 3 Switch the shaver off by pressing the on/off button once. Put the protection cap on the shaver every time you have used it, to prevent damage. 2 C 4 Trimming For grooming sideburns and moustache. C Open the trimmer by pushing the slide upwards. The trimmer can be activated while the motor is running. 5 8 ENGLISH Cleaning and maintenance Regular cleaning guarantees a better shaving performance. The easiest and most hygienic way to clean the appliance is to rinse the shaving unit and the hair chamber with hot water every time you have used the shaver. Be careful with hot water. Always check if the water is not too hot, to prevent your hands from getting burnt. C For easy and optimal cleaning, the Philishave Action Clean (shaving-head cleaner, type B HQ100) is available.Ask your Philishave dealer for information. The Philishave Action Clean may not be available in all countries. Contact the Customer Care Centre in your country about the availability of this accessory. You can also clean the shaver in the following way: Every day: shaving unit and hair chamber When you clean the appliance, it is not necessary to take the shaving heads (cutters and guards) apart. If you want to take them apart, be sure not to mix up the cutters and guards, since grinding of the cutters in the guards only guarantees optimal performance for each matching set. If you accidentally mix up the sets, it could take several ENGLISH weeks before optimal shaving performance is restored. 1 2 9 Switch the shaver off, remove the powerplug from the wall socket and pull the appliance plug out of the shaver. Press the release button (1) and open the shaving unit (2). Clean the shaving unit and the hair chamber by rinsing them under a hot tap for some time. 1 C C 2 3 Close the shaving unit and shake off excess water. Never dry the shaving unit with a towel or tissue as this may damage the shaving heads. 4 C Open the shaving unit again and leave it open to let the appliance dry completely. You can also clean the hair chamber without water by using the brush supplied. 5 Trimmer Clean the trimmer every time you have used it. 1 Switch the shaver off, remove the powerplug from the wall socket and pull the appliance plug out of the shaver. Clean the trimmer with the brush supplied. C 2 10 ENGLISH C 3 Lubricate the trimmer teeth with a drop of sewing machine oil every six months. Storage C Put the protection cap on the shaver to prevent damage. The appliance can be stored in the pouch supplied. Replacement Replace the shaving heads every two years for optimal shaving results. Replace damaged or worn shaving heads with Philishave HQ6 Quadra shaving heads only. 1 2 Switch the shaver off, remove the powerplug from the wall socket and pull the appliance plug out of the shaver. Press the release button (1) to open the shaving unit (2). Turn the wheel anti-clockwise (1) and remove the retaining frame (2). 1 C 2 1 2 3 C ENGLISH 11 C Remove the shaving heads and place the new ones in the shaving unit in such a way that the parts with the small holes point towards the centre of the shaving unit. Make sure that the projections of the shaving heads fit exactly into the recesses. 5 Put the retaining frame back into the shaving unit, press the wheel (1) and turn it clockwise (2). 4 1 C 2 Accessories The following accessories are available: - HQ6 Quadra Philishave shaving heads. - HQ8000 powerplug. - HQ100 Philishave Action Clean (shaving head cleaner). - HQ101 Philishave Action Clean refill (shaving head cleaning liquid). - HQ110 Philishave shaving head cleaner (shaving head cleaning spray). Environment The built-in rechargeable batteries contain substances that may pollute the environment. Disposal of batteries Remove the batteries when you discard the appliance. Do not throw the batteries away with 12 ENGLISH the normal household waste, but hand them in at an official collection point.You can also take the appliance to a Philips service centre, which will remove the batteries for you and will dispose of them in an environmentally safe way. Only remove the batteries if they are completely empty. 1 Remove the powerplug from the wall socket and pull the appliance plug out of the shaver. Let the shaver run until it stops, open the trimmer, undo the screws and open the shaver. C 2 3 Remove the batteries. Do not connect the shaver to the mains again after the batteries have been removed. Guarantee & service If you need information or if you have a problem, please visit the Philips Web site at www.philips.com or contact the Philips Customer Care Centre in your country (you will find its phone number in the worldwide guarantee leaflet). If there is no Customer Care Centre in your country, turn to your local Philips dealer or contact the Service Department of Philips Domestic Appliances and Personal Care BV. ENGLISH 13 Troubleshooting 1 Reduced shaving performance Cause 1: the shaving heads are dirty. B The shaver has not been rinsed long enough or the water used was not hot enough. B Clean the shaver thoroughly before you continue shaving (see chapter 'Cleaning and maintenance'). B 2 1 Cause 2: long hairs are obstructing the shaving heads. the wheel C Open the shaving unit, turnthe retaininganticlockwise (1) and remove frame the and guards. C Cleancleancuttersthan one cutter and guard at Do not more a time, since they are all matching sets. If you accidentally mix up the cutters and guards, it may take several weeks before optimal shaving performance is restored. Remove the hairs with the brush supplied. Put the shaving heads back into the shaving unit, put the retaining frame back into the shaving unit, press the wheel and turn it clockwise. B (2). Cause 3: shaving heads are damaged or worn. Remove the retaining frame. 14 ENGLISH Remove the old shaving heads from the shaving unit and replace them with new ones Damaged or worn shaving heads (cutters and guards) must only be replaced with the original Philishave HQ6 Quadra shaving heads. Put the retaining plate back into the shaving unit, press the wheel and turn it clockwise. 2 B The shaver does not work when the ON/OFF button is pressed Cause: the batteries are empty. Recharge the batteries. See chapter 'Charging'. The shaving unit has not been placed correctly. 3 Shaving unit has come off the shaver unit becomes detached from the C If the shaving whether the hinge spring is still shaver, check properly attached, i.e. has not come loose and does not show any cracks or damage. If the hinge spring is still properly attached, the shaving unit can be easily put back on the shaver again. However, if the hinge spring has come loose, is cracked or damaged, please contact your Philips dealer or the nearest Philips service centre to avoid damage to your shaver. DEUTSCH 15 Wichtig Lesen Sie diese Bedienungsanleitung vor dem ersten Gebrauch des Geräts gründlich durch und bewahren Sie sie zur späteren Einsichtnahme auf. Verwenden Sie zum Aufladen der Akkus nur das mitgelieferte Netzteil. Das Netzteil wandelt Netzspannungen von 100 bis 240 Volt in eine sichere Betriebsspannung von unter 24 Volt um. Benutzen Sie nur das mitgelieferte Netzteil, damit eine sichere Spannungsumwandlung gewährleistet ist. Das Netzteil enthält einen Transformator. Ersetzen Sie das Netzteil keinesfalls durch einen anderen Stecker, da dies den Benutzer gefährdet. Ist das Netzteil defekt, darf es nur durch ein Original-Ersatznetzteil ausgetauscht werden, um ein Sicherheitsrisiko zu vermeiden. Achten Sie darauf, dass das Netzteil nicht nass wird. Laden und benutzen Sie das Gerät bei Temperaturen zwischen 5cC und 35cC. Bewahren Sie es auch in diesem Temperaturbereich auf. Nehmen Sie den Rasierer zum Laden aus der Tasche. Das Gerät erfüllt die internationalen IEC Sicherheitsvorschriften und kann ohne Bedenken unter fließendem Wasser gereinigt werden. C C 16 DEUTSCH Gehen Sie vorsichtig mit heißem Wasser um. Achten Sie darauf, dass das Wasser nicht zu heiß ist und Sie sich nicht die Hände verbrühen. Ziehen Sie stets das Netzteil aus der Steckdose, bevor Sie den Rasierer unter fließendem Wasser reinigen. Aufladen Beim ersten Laden und wenn der Rasierer für einen längeren Zeitraum nicht benutzt wurde, sollte er 4 Stunden ununterbrochen geladen werden. Normalerweise ist der Akku nach ungefähr 1 Stunde voll aufgeladen. Lassen Sie das Gerät nicht länger als 24 Stunden ununterbrochen am Netz. Sie können sich auch bei leeren Akkus rasieren, indem Sie den Rasierapparat an das Netz anschließen. Ladeanzeigen Aufladen dem Laden beginnen, leuchtet C Wenn Sie mitKontrolllampe rot. Sobald die die unterste Akkus ausreichend Energie für eine Rasur enthalten, blinkt die unterste Kontrolllampe grün. Während des Ladevorgangs leuchten weitere grüne Kontrolllampen auf und zeigen den Ladestand der Akkus an. DEUTSCH 17 Akkus voll aufgeladen C Wenn die Akkus voll geladen sind, leuchten alle grünen Kontrolllampen. Restkapazität den Akkus verbleibende Energie C Die in die Anzahl der leuchtenden wird durch Kontrolllampen angezeigt. So wie die Akkukapazität abnimmt, erlöschen auch die Lampen nach einander. Die Energie geht zur Neige Akkukapazität zur Neige C Wenn diedie unterste Kontrolllampegeht, leuchtet rot. Sobald Sie den Rasierer ausschalten, blinkt die rote Lampe 4 Sekunden lang. Laden des Geräts Laden Sie den Rasierer nicht in einer geschlossenen Tasche auf. C 1 2 Stecken Sie den Gerätestecker in den Rasierer. Stecken Sie das Netzteil in die Steckdose. 18 DEUTSCH 3 Ziehen Sie das Netzteil aus der Steckdose und den Gerätestecker aus dem Rasierer, sobald die Akkus voll geladen sind. Kabelfreie Rasierzeit Mit voll aufgeladenen Akkus können Sie sich ca. 70 Minuten rasieren. Benutzung des Geräts Rasieren 1 Schalten Sie das Gerät ein, indem Sie den Ein-/Ausschalter drücken. C Führen Sie die Sc ...