(this page intentionally left blank) 1 En IMPORTANT CAUTION RISK OF ELECTRICAL SHOCK DO NOT OPEN The lightening flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of un-insulated "dangerous voltage" with the product's enclosure that may be of sufficient magnitude to constitute a risk of electrical shock to individuals. CAUTION: TO PREVENT THE POSSIBLE RISK OF ELECTRICAL SHOCK OR INJURY, DO NOT REMOVE THE COVER (FRONT, BACK, OR TOP). NO USER-SERVICABLE PARTS ARE INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The exclamation mark within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment OFF and ON, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiver or receiving antenna. Increase the separation between the equipment and the receiver. Plug the equipment into an outlet on a circuit different from the receiver. Consult the dealer or an experienced radio/TV technician for assistance. Information to User: Alteration or modifications carried out without appropriate authorization may invalidate the user's right to warranty service or other assistance. [For Canadian Model] This Class B apparatus complies with Canadian ICES-003. [Pour le modèle Canadien] Cet appareil numérique de le Classe B est conforme à la norme NMB-003 du Canada. DANGER ­ VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN. AVOID DIRECT EXPOSURE TO BEAM. CAUTION: Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. CAUTION: The use of optical instruments with this product will increase eye hazard. 2 En This product complies with the EMC Directives (89/336/EEC, amended by 92/31/EEC and 93/68/ECC). Cet produit est conforme aux Directives relatives à la Compatibilité Électromagnétique (89/336/CEE, amendements 92/31/CEE et 93/68/CEE). Este producto cumple con las Directivas EMC (89/336/CE, correcto por la 92/31/CE y la 93/68/CE). Federal Communications Commission Declaration or Conformity This device complies with part 15 of the FCC Rules. Operation is subject to the following two (2) conditions: ( 1 ) This device may not cause harmful interference ( 2 ) This device must accept any interference received, including interference that may cause undesired operation. Product Name: DVD / CD Writer Model Numbers: DVR-710 Responsible Party Name: PIONEER ELECTRONICS (USA) INC. Customer Support Division Address: 1925 E. Dominguez Street, Long Beach, CA 90810 U.S.A. 3 En Thank you for buying this Pioneer product. Please read through these operating instructions so you will know how to operate your model properly. After you have finished reading the instructions, put them away in a safe place for future reference. WARNING: This product is not waterproof. To prevent a fire or shock hazard, do not place a container filled with liquid near this unit or expose it to other sources of moisture. WARNING: Handling the product's cord or cords associated with accessories sold with the unit will expose you to lead, a chemical known by California and other governmental entities to cause cancer and birth defects or other reproductive harm. Wash Hands After Handling. The generation of acoustical noise is less than 70dB (ISO7779/DIN45635) CAUTION This product is a Class 1 laser product but this product contains a laser diode higher than Class 1. To ensure continued safety, do not remove any covers or attempt to gain access to the inside of this product. Refer all servicing to qualified personnel. The caution label shown to the right appears on your unit (top of cover). IMPORTANT NOTICE ­ RECORD THE MODEL NUMBER AND SERIAL NUMBER OF THIS UNIT BELOW. THE NUMBERS ARE ON THE REAR PANEL. MODEL #: SERIAL #: DVR-710 KEEP THESE NUMBERS FOR FUTURE REFERENCE. is a trademark of the DVD Format / Logo Licensing Corporation. 4 En SAFETY INSTRUCTIONS To ensure your personal safety and to maximize the full operating potential of your unit, read and follow these safety instructions. Environment ­ Avoid installing this drive in a location with exposure to large quantities of dust, high temperatures, high humidity, or subject to excessive vibrations or shocks. Power ­ Turn OFF the system before installing this or any other hardware device. Read & Retain Instructions ­ Read all operating and user information provided with this drive. Cleaning ­ Use a damp cloth to clean the exterior housing. Avoid using any fluids including liquid, aerosol or alcohol-based cleaning products. Water or Moisture ­ Avoid operating or locating this drive near water or other sources of fluid. Power Sources ­ Operate this drive only from the recommended power sources. If you are unsure of the power source, consult an authorized Pioneer representative. Overloading ­ Avoid connecting too many devices to a single wall socket or power source as this can cause fires or short circuits. Object & Liquid Entry ­ Never push inappropriate objects in to the device. Avoid spilling any liquids in to or on the outside of the drive. Condensation ­ Moisture can form in the operating section of the product if the drive is taken from cool surroundings to a room with a warmer temperature. Let the drive stand for one to two hours in the new location before turning it ON. Servicing ­ Opening or removing the cover exposes you to possible electrical shock or other danger. Contact a Pioneer authorized service representative for repairing this drive (refer to the enclosed Service & Support Card). About DualDisc Playback ­ DualDisc is a new two-sided disc with one side containing DVD video / audio / etc. content and the opposite side containing non-DVD content such as digital audio material. The non-DVD audio side is not compliant with the CD Audio Specification; therefore, may not play. The DVD side of DualDisc media plays in this unit. For more details about the DualDisc specification, please refer to the disc manufacturer or your retailer. Note: Some discs may not be playable due to different recording formats or the physical condition of the disc at the time of recording or playback. 5 En FEATURES Write Speed (*CAV, **ZCLV, *** This specification describes the maximum speed in one zone.) DVD-R 1X, 2X, 6X, 8X**, 12X**, 16X* DVD-R (DL) 2X, 4X, 6X, 8X*** DVD-RW 1X, 2X, 4X, 6X DVD+R 2.4X, 4X, 6X, 8X**, 12X**, 16X* DVD+R (DL) 2.4X, 4X, 6X, 8X*** DVD+RW 2.4X, 3.3X, 4X, 6X, 8X** CD-R 4X, 10X, 16X, 24X**, 32X**, 40X* CD-RW 4X, 10X, 16X, 20X**, 24X**, 32X** Maximum Read Speed DVD-ROM (single) DVD-R, DVD+R DVD-RW, DVD+RW CD-ROM, CD-R DVD-RAM DualDisc 16X 12X 8X 40X 2X** DVD-ROM (DL) DVD-R (DL) DVD+R (DL) CD-RW 12X 8X 8X 32X (please refer to the previous page in this document) IDE Data Transfer Mode PIO Mode 4 / Multi-Word DMA Mode 2 / Ultra DMA Mode 4 Buffer Size 2 MBytes (Read/Write) 5.25" Half-Height built-in type Stereo Audio Output LCD Tilt-Servo Mechanism Horizontal / Vertical orientation Low vibration mechanism by DRA System Disc Format (Read/Write) DVD single layer/dual layer / 120mm / 80mm disc DVD-R (when writing, use only 650nm ­ for General use ­ media) DVD-R (4X, 8X, 16X write speed) Dual Layer DVD-R and Double Layer DVD+R DVD-RW (1X, 2X, 4X, 6X write speed) DVD+R (2.4X, 4X, 8X, 16X write speed) DVD+RW (2.4X, 4X, 8X write speed) DVD-RAM (non-cartridge, Version 2.0, Version 2.1) (Read only) CD-ROM Mode 1 CD-R XA Mode 2 (form 1, form 2) Photo CD (single and multiple sessions) CD-DA CD-Extra (CD PLUS) Video-CD CD Text CD-R CD-RW / High Speed CD-RW / Ultra Speed CD-RW Note: A specific application program is necessary to write the formats listed above. Supported media required for specific DVD and CD writing speeds. When writing to DVD at 12X and 16X, use Pioneer-tested media. For media brand information, refer to the Pioneer website: www.pioneerelectronics.com 6 En Interface 1) Forced Ejection Hole If the tray fails to eject when the Eject button is pressed, insert a stiff rod into the hole and push to eject the tray. During normal operation, the eject button should be used to unload the tray. Turn the power to the drive OFF then wait approximately one minute until the disc stops spinning before trying to eject the tray using the Forced Ejection Hole. 2) BUSY Indicator Operation status is indicated as follows: During reading Lights During writing Lights 3) Eject Button Press the button to unload / load the disc. 4) Disc Tray Press the Eject button to open the loading tray then place a CD or DVD disc onto the tray with the label facing up. Press the Eject button again or gently push the tray to close and load. Do not attempt to pull out the disc tray forcibly ­ use the Forced Ejection Hole (1). Precautions When Playing 8cm (3.15") Discs An 8cm (3.15") disc cannot be played when the drive is mounted vertically even with an adapter. ABOUT REGION CODES The region code can only be changed five (5) times, including the initial setting. Please be aware that the fifth change becomes PERMANENT. Therefore, avoid changing the region code unless absolutely necessary. Region codes are part of the DVD Standard. However, region codes on DVD discs are optional. DVD discs with no specified region code can be played on all compliant players. 7 En INTERFACE 5) Audio Output This connector outputs analog audio. This connector is compatible with `Molex 70553' choose a suitable connection cable. Pin 1 2 3 4 Name L G G R Function (Left channel audio output Ground Ground Right channel audio output 6) Device Configuration Jumper (switch turns ON when a jumper is added) Power OFF the drive before changing the jumper setting. Pin #1 is ON when shipped from the factory Pin 1 2 3 4 5 Name MA SL CS Function ON Drive set to Master mode ON Drive set to Slave mode ON Drive set to Cable-Select Reserved Reserved 7) Host IDE Interface This is a 40-pin I/O connector in accordance with the ATA specifications. 8) DC Input Pin 1 2 3 4 Name +12 G G +5 Function Power Supply input for DC +12 V Ground Ground Power Supply input fo +5 V 8 En INSTALLATION 1) 2) 3) 4) 5) Turn OFF the computer's power and remove the power cord from the wall outlet before removing the front cover. Remove the blank panel from the front of the empty 5.25" bay slot. Install the slide rails on the drive if necessary. (Please contact the store where the drive was purchase to obtain slide rails.) Insert the drive into the slot. When anchoring is required, refer to the computer's instruction manual. · Please use screws measuring 5mm (3/16") or less for mounting. Using longer screws may damage the drive. · When the mounting screws are loose, the vibrations from a spinning disc may generate a ripping noise. To prevent this noise, tighten the screws. 9 En CONNECTIONS · Turn OFF the power to the computer. · Connect the computer's power cable to the drive, checking the polarity of the cable. · Connect the computer's IDE interface cable to the drive, confirming that cable's Pin #1 is matched to the drive's Pin #1. · Connect an audio output cable to the drive if using a sound card. The computer powers this product. Do NOT use a power supply other than the internal source provided by the PC. 80-wire IDE cable is required for 16X DVD writing speed 10 En SPECIFICATIONS [Position] This unit may be installed vertically as well as horizontally. [Disc Size] 12 cm / 8 cm (Drive does not support non-standard shapes such as business cards, diamond, etc.) * 8cm disc cannot be used vertically ­ adapters do not effect this limitation [Disc Transfer Rate] Data Read (sustained) DVD CD Data Write (sustained) DVD CD Max. 21.6 MBytes/sec. Max. 6.00 MBytes/sec. (6.6X ­ 16X CAV Mode over 16 block transfer) (16.2X ­ 40X CAV Mode over 16 block transfer) Max. 21.6 MBytes/sec. (Max 16X DVD-R) Max. 6.00 MBytes/sec. (Max. 40X CD-R) Host Inferface Specification PIO Mode 4 / Multi-word DMA Mode 2 Ultra DMA Mode2 Ultra DMA Mode 4 (U-ATA66 cable, 80 conductor) * 80-wire IDE cable is required for 16X DVD writing speed. * Media that is dirty or damaged can affect the transfer rate. 16.6 MBytes/sec ...