CT1744NU Manual 1-866-PLANAR-1 customerservice@planar.com Preface PREFACE About this manual This manual is designed to assist you in setting up and using the LCD monitor. Information in this document has been carefully checked for accuracy; however, no guarantee is given to the correctness of the contents. The information in this document is subject to change without notice. This document contains proprietary information protected by copyright. All rights are reserved. No part of this manual may be reproduced by any mechanical, electronic or other means, in any form, without prior written permission of the manufacturer. Copyright Copyright 2001, All Rights Reserved FCC Compliance Statement This device complies with part 15 of the FCC Rules. Opeartion is subject to the following two conditions: 1. 2. this device may not cause harmful interference, and this device must accept any interference received, including interference that may cause undesired operation. FCC WARNING This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful inerference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · · · · Reorient or relocate the receiving antenna. Increase the separation between the equipment and the receiver. Connect the equipment into an outlet different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Caution: To comply with the limits for an FCC Class B computing device, always use the shielded signal cord supplied with this unit. The Federal Communications Commission warns that changes or modifications of the unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. CE mark for Class B ITE (Following European standard EN55022/1998; EN61000-3-2/1995; EN61000-3-3/1995, EN55024/1998, EN60950/1992+A1+A2+A3+A4+A11) Radio Frequency Interference Statement Warning: This is a Class B product. In a domestic environment, this product may cause radio interference in which case the user may be required to take adequate measures. i Planar User's Manual Canadian Doc Notice For Class B Computing Devices This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the Radio Interference Regulation of the Canadian Department of Communications. "Le présent appareil numérique n'èmet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de la class B prescrites dans le Règlement sur le brouillage radioélectrique édicté par le ministère des Communications du Canada" Important Operating Instructions Please read the following instructions carefully. This manual should be retained for future use. 1. To clean the LCD monitor screen, first, make sure the monitor is in the power off mode. Unplug the monitor from its power source before cleaning it. Do not spray liquid cleaners directly onto the unit. Without applying excessive pressure, clean the screen with a slightly dampened rag. Do not place your LCD monitor near a window. Exposing the monitor to rain, water, moisture, or sunlight can severely damage it. Do not place anything on top of the monitor-to-PC signal cord. Make sure the cord is placed in an area where it will not be stepped on. Do not apply pressure to the LCD screen. Excessive pressure may cause permanent damage to the display. Do not remove the cover or attempt to service this unit by yourself. You may void the warranty. Servicing of any nature should be performed only by an authorized technician. Safe storage of the LCD monitor is in a range of minus 20 to plus 60 degrees Celsius. Storing your LCD monitor outside this range could result in permanent damage. Only with use of supplied adapter, in case of loss or replacement contact the retailer or service center. Immediately unplug your monitor and call an authorized technician when: · · · The power or monitor-to-PC signal cord is frayed or damaged. Liquid has been spilled into the monitor, or it has been exposed to rain. The monitor has been dropped or the case has been damaged. 2. 3. 4. 5. 6. 7. 8. ii Preface Table of Contents PREFACE ......................................................................................................................................................................................... I CHAPTER 1...................................................................................................................................................................................... 1 Your New Planar LCD Monitor!..............................................................................................................................1 Unpacking ................................................................................................................................................................1 Identifying Components .........................................................................................................................................1 The LCD Monitor -- Front View.......................................................................................................................................... 1 The LCD Monitor -- Rear View ........................................................................................................................................... 2 Adjusting the Viewing Angle..................................................................................................................................3 Connecting AC Power ............................................................................................................................................3 Connecting Video....................................................................................................................................................3 Connecting the Stereo Speakers...........................................................................................................................4 Power Management System...................................................................................................................................4 CHAPTER 2...................................................................................................................................................................................... 6 Your New Planar LCD Monitor's Display Controls ..............................................................................................6 Adjusting the Monitor's Display ............................................................................................................................6 OSD Main Menu (Analog mode).............................................................................................................................6 OSD Main Menu (Digital mode)..............................................................................................................................9 APPENDIX A.................................................................................................................................................................................. 12 TFT LCD Monitor Specifications..........................................................................................................................12 APPENDIX B .................................................................................................................................................................................. 13 APPENDIX C.................................................................................................................................................................................. 14 Troubleshooting Procedures ...............................................................................................................................14 iii CHAPTER 1 The LCD Monitor Your New Planar LCD Monitor! Your LCD monitor has been designed to be versatile, ergonomic, and easy to use. The LCD monitor is capable of displaying most standards, from 640 x 480 VGA to 1280 x 1024 SXGA. The digital controls located on the front panel allow you to easily adjust the monitor's display parameters. The LCD monitor has the additional feature of a VESA arm-mounted interface for added convenience. Unpacking After you unpack your LCD monitor, make sure the following items are included in the box and in good condition: Standard Items · LCD Monitor · Monitor-to-PC signal cable (15-pin) · Monitor-to-PC Digital signal cable (24-pin) · USB cable (optional) · Stereo Jack Audio Cable · · · Power cord AC/DC adapter This user's manual If you find that any of these items are missing or appear damaged, contact your dealer immediately. Do not throw away the packing material or shipping carton in case you need to ship or store the LCD monitor in the future. Identifying Components The following figures will help you identify the LCD monitor's controls and ports. The LCD Monitor -- Front View 1 Planar User's Manual 1. Display Module The display is a 17.4" diagonal, Active Matrix Liquid Crystal Display (AMLCD). The screen is capable of supporting a maximum resolution of 1280 x 1024 (SXGA). 2. FunctionSelect Buttons These two buttons allow you to select the control functions in the OSD. Press either button to scroll horizontally through the main menu and submenu items. Adjust Control Buttons The button allows you to increase the menu item value. The button allows you to decrease the menu item value. Menu Push the Menu select button activates the On Screen Display (OSD). LED Power Mode Indicator This LED indicator stays lit when the power is on and when the monitor is receiving a proper video signal. The LED will blink slowly when the LCD monitor is in power saving mode. 3. 4. 5. The LCD Monitor -- Rear View 1. DC Power Jack for AC adaptor Connect the AC adapter cable to this jack. 2. Upstream USB Port (optional) Connect the LCD monitor's upstream USB port to your PC's USB port. 3. Downstream USB Ports (optional) The monitor's two downstream USB ports let the LCD monitor function as a USB hub allowing the connection of USB compliant devices. The upstream USB port must be connected to your PC for the downstream ports to function. 4. Audio Line-in (optional) Connect your PC's line-out to this jack to listen the PC's audio on the LCD monitor's stereo speakers. (You can also connect your CD-ROM's line-out to this jack.) 5. VGA Cable Connector This 15-pin D-Sub VGA connector is used to connect to your PC's VGA card. 6. Digital VGA Cable Connect (optional) This 24-pin DVI connect is used to connect to you PC's Graphic card which has a DVI conector 2 Chapter 1 Adjusting the Viewing Angle Your LCD Monitor is designed to allow you to adjust it to a comfortable viewing angle. The LCD Monitor's angle setting range is from -5° to 15°. Connecting AC Power 1. Plug the female end of the power cable into the AC-adapter. Plug the male end of the power cord into a wall socket. The plug on the power cable will vary according to the electrical standard in your area. 2. Connect the power connector of the adapter into the jack of the LCD Monitor. The AC power jack is located at the rear of the Monitor near the D-sub VGA connector. Connecting Video 1. Turn off your PC and the LCD Monitor before connecting your LCD 2. Monitor to the computer. 3. Connect the VGA signal cable to the D-sub VGA connector located at the rear of the monitor. 4. PC has a graphic card with a 24-pin DVI connector, you should connect it with the Digital 24-pin DVI signal cable. 3 Planar User's Manual 5. Make sure the signal cable heads are securely connected to the VGA ports of your PC and Monitor. Tighten the connecting screws to ensure a secure connection. 6. Turn on your computer and LCD Monitor. Connecting the Stereo Speakers Please refer to the following instructions for connecting the LCD Monitor's stereo speakers. 1. Connect the 1.5M sound cable to the Lineout of your PC's audio card. 2. Connect the other end of the 1.5M sound cable to the LCD Monitor's line-in jack. 3. You can adjust the sound volume of the stereo speakers by using the speaker volume control function on the OSD (On-Screen Display). Power Management System T ...