PT1704Z Manual 1-866-PLANAR-1 customerservice@planar.com Preface PREFACE About this manual This manual is designed to assist you in setting up and using your New Planar LCD Monitor. Information in this document has been carefully checked for accuracy; however, no guarantee is given to the correctness of the contents. The information in this document is subject to change without notice. This document contains proprietary information protected by copyright. All rights are reserved. No part of this manual may be reproduced by any mechanical, electronic or other means, in any form, without prior written permission of the manufacturer. FCC Compliance Statement This device complies with part 15 of the FCC Rules. Opeartion is subject to the following two conditions: 1. 2. this device may not cause harmful interference, and this device must accept any interference received, including interference that may cause undesired operation. FCC WARNING This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful inerference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · · · · Reorient or relocate the receiving antenna. Increase the separation between the equipment and the receiver. Connect the equipment into an outlet different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Caution: To comply with the limits for an FCC Class B computing device, always use the shielded signal cord supplied with this unit. The Federal Communications Commission warns that changes or modifications of the unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. CE mark for Class B ITE (Following European standard EN55022/1998; EN61000-3-2/1995; EN61000-3-3/1995, EN55024/1998) Radio Frequency Interference Statement Warning: This is a Class B product. In a domestic environment, this product may cause radio interference in which case the user may be required to take adequate measures. Canadian Doc Notice For Class B Computing Devices i Planar User's Manual This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the Radio Interference Regulation of the Canadian Department of Communications. "Le présent appareil numérique n'èmet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de la class B prescrites dans le Règlement sur le brouillage radioélectrique édicté par le ministère des Communications du Canada" Important Safety Instructions Please read the following instructions carefully. This manual should be retained for future use. 1. To clean your New Planar LCD Monitor screen, first, make sure the Monitor is in the power off mode. Unplug the Monitor from its power source before cleaning it. Do not spray liquid cleaners directly onto the unit. Stand away from your New Planar LCD Monitor and spray cleaning solution onto a rag. Without applying excessive pressure, clean the screen with the slightly dampened rag. Do not place your New Planar LCD Monitor near a window. Exposing the Monitor to rain, water, moisture or sunlight can severely damage it. Do not place anything on top of the Monitor-to-PC signal cord. Make sure the cord is placed in an area where it will not be stepped on. Do not apply pressure to the LCD screen. Excessive pressure may cause permanent damage to the display. Do not remove the cover or attempt to service this unit by yourself. You may void the warranty. Servicing of any nature should be performed only by an authorized technician. Safe storage of your New Planar LCD Monitor is in a range of minus 20 to plus 65 degrees Celsius (68°F149°F). Storing your New Planar LCD Monitor outside this range could result in permanent damage. If any of the following occurs, immediately unplug your Monitor and call an authorized technician. · · · 8. 9. The power or Monitor-to-PC signal cord is frayed or damaged. Liquid has been spilled onto the Monitor, or it has been exposed to rain. The Monitor has been dropped or the case has been damaged. 2. 3. 4. 5. 6. 7. The appliance should be disconnected from the mains by pulling the mains power cord/mains plug. The socket-outlet shall be installed near the equipment and shall be easily accessible. ii Table of Contents TABLE OF CONTENTS PREFACE..........................................................................................................................................................................I TABLE OF CONTENTS...............................................................................................................................................III CHAPTER 1 ..................................................................................................................................................................... 1 Your New Planar LCD Monitor! ...............................................................................................................1 Unpacking .................................................................................................................................................1 Identifying Components ..........................................................................................................................1 Your New Planar LCD Monitor -- Front View ................................................................................................... 2 Your New Planar LCD Monitor -- Rear View..................................................................................................... 2 Adjusting the Viewing Angle...................................................................................................................3 Connecting AC Power..............................................................................................................................3 Connecting Video .....................................................................................................................................4 Connecting the Stereo Speakers ............................................................................................................4 CHAPTER 2 ..................................................................................................................................................................... 5 Your New Planar LCD Monitor's Display Controls ...............................................................................5 Adjusting the Monitor's Display .............................................................................................................5 OSD Main Menu .................................................................................................................................................. 5 OSD Main Menu ........................................................................................................................................5 APPENDIX A ................................................................................................................................................................... 9 Planar TFT LCD Monitor Specifications.................................................................................................9 APPENDIX B ................................................................................................................................................................. 10 Timing for Model PT1704Z (SXGA Resolution) ...................................................................................10 APPENDIX C ................................................................................................................................................................. 11 Troubleshooting Procedures ................................................................................................................11 iii CHAPTER 1 Your New Planar LCD Monitor Your New Planar LCD Monitor! Your New Planar LCD Monitor has been designed to be versatile, ergonomic and user-friendly. . The LCD Monitor is capable of displaying most standards, from 640 x 480 VGA to 1280 x 1024 SXGA. The digital controls located on the front panel allow the user to easily adjust the Monitor's display parameters. Your New Planar LCD Monitor's small footprint allows you more room in your workspace for other peripherals. Lightweight and compact, your New Planar LCD Monitor is the perfect solution for users on the go. You can use your New Planar LCD Monitor for everything from making business presentations to playing computer games. The two stereo speakers allow you to further expand your computer's multimedia capabilities by connecting your computer's Audio out port to your New Planar LCD Monitor's Audio in port. If you have a complete full workstation, your New Planar LCD Monitor has the additional feature of an optional wall-mountable stand for added convenience. The architecture of your New Planar LCD Monitor incorporates an LCD panel that produces a clear display with low radiation emission, limiting health concerns. With its low power consumption, your New Planar LCD Monitor helps you reduce your power bill. Unpacking Before you unpack your New Planar LCD Monitor, prepare a suitable workspace for your New Planar LCD Monitor and computer. You need a stable, level and clean surface near a wall outlet. Even though your New Planar LCD Monitor uses very little power, you should put it in a location that allows sufficient airflow to ensure that your New Planar LCD Monitor and your computer do not become too hot. Set up your New Planar LCD Monitor so that the panel does not face a window where sunlight often comes in. The glare caused by sunlight reflecting off your New Planar LCD Monitor's screen will make it difficult to see. Using a computer for an extended period of time with a poor workstation set-up and incorrect working habits can cause health problems. The science of ergonomics studies the relationship between health and a suitable working environment. There is a section on ergonomics at the end of this chapter. For more information on ergonomics, contact your nearest computer bookstore, or local library. The Internet also has information on this and other subjects. After you unpack your New Planar LCD Monitor; make sure the following items are included in the box and in good condition: · · · · · LCD Monitor Monitor-to-PC signal cable 1.5M Stereo Jack Audio Cable AC Adapter Power cord · This Planar User's Manual If you find that any of these items are missing or appear damaged, contact your dealer immediately. Do not throw away the packing material or shipping carton in case you need to ship or store your New Planar LCD Monitor in the future. Identifying Components Your New Planar LCD Monitor has been designed to provide easy access to all controls and peripheral ports. The following figures will help you identify your New Planar LCD Monitor's controls and ports. 1 Planar User's Manual Your New Planar LCD Monitor -- Front View 1. LCD Screen This is the LCD monitor screen. It is a 17-inch diagonal, Acitve Matrix Liquid Crystal Display (AMLCD). The screen is capable of supporting a maximum resolution of 1280 x 1024 (SXGA). Function Select Buttons These two buttons allow you to select the control functions in the OSD. Press either button to vertically scroll through the main menu and submenu items. Adjust Control Buttons This button allows you to apply settings and enter submenus in the OSD. This button also serves as an Adjustment Control button. Power ON / OFF and Menu Button This button allows you to activate the OSD Menu. The button is also used as a power ON/OFF switch. Press the button to activate the OSD Menu. Press the button and hold it down for two seconds will turn on or turn off the monitor. Power-On Indicator This LED indicator stays lit when the power is on and when the monitor is receiving a proper video signal. The LED will blink slowly when the LCD monitor is in power saving mode. Monitor Stand The monitor stand supports the LCD monitor. Stereo Speakers 2. 3. 4. 5. 6. 7. Your New Planar LCD Monitor -- Rear View 2 Chapter 1 1. LCD Monitor's VGA Connector This 1.5 meter cable has two 15-pin D-Sub VGA connectors used to ...