User manual PLANTRONICS M3000 - PAIRING

Plantronics Ltd - Released M3000 Pairing Instructions ­ Nokia 3650 Mobile Phone Before pairing the Plantronics M3000 with the Nokia 3650, please ensure both devices are fully charged according to the instructions in the respective User Guides. 1. Turn the Nokia 3650 phone and the Plantronics M3000 headset ON. 2. On the 3650: a) Press the Menu key, then use the scroll keys to choose the Connectivity menu. Press the middle of the scroll key to Select. b) Use the scroll keys to choose the Bluetooth menu (this is normally the menu displayed) and press the middle of the scroll key to select. c) Use the scroll keys to choose the choose Bluetooth Off (this is normally the menu displayed) and press the middle of the scroll key to select. d) The handset will display Bluetooth On. In this menu. Bluetooth is now be switched on in the phone. 3. On the Plantronics M3000: a) Put the M3000 into pairing mode by press the "Volume Up" & "Call Control" buttons simultaneously until the Indicator light begins to flash alternate green and red. (see M3000 User Instructions). 4. On the Nokia 3650: a) In the Bluetooth menu, use the right scroll menu to select the Paired devices menu b) Press the Options key, scroll to New paired device (default) and press Select. The phone displays Searching for audio accessories c) In a few moments, the phone will display all nearby Bluetooth devices. Using scroll key, choose M3000 by Plantronics and press the Select key. d) Enter the 4-digit Passkey 0000 and press the OK key. The handset will display Pairing with M3000 by Plantronics complete. e) The M3000 will appear in the Paired device list. Your M3000 headset is now paired with the 3650 phone. 3650 M3000 pair rev002 1 24th July 2003 Plantronics Ltd - Released Before connecting the headset to the phone, please do the following: a) While in the Bluetooth menu, use the scroll keys to select Paired Devices. b) The display will show M3000 by ... and possibly other devices. Use the scroll key to select M3000 by ... and press Options c) Use the scroll keys to select Set as authorised. Press Select. The display will show Connections will take place automatically without confirmation. Continue? Press Yes. The headset must now be connected to the phone. This can be done in 2 ways: Using the Phone Menu a) While in the Bluetooth, use the scroll keys to select Paired Devices. b) The display will show M3000 by Plant ... and possibly other devices. Use the scroll key to select M3000 by Plant ... and press Options c) Use the scroll keys to select Connect then press Select d) The phone will display Connecting to M3000 by plantronics, then Connected to M3000 by plantronics. e) Press the End Call button to return to main menu. Using the M3000 headset If the headset is switched off, it will be disconnect from the 3650. The headset can be reconnected by simply pressing the headset Call Control button. 3650 M3000 pair rev002 2 24th July 2003 Plantronics Ltd - Released Making and Accepting Calls To accept an in-coming call via the M3000 Headset 1. An in-coming call will cause both the phone and the headset to ring. Note that there may be a delay of a few seconds between the phone ringing and the headset starting to ring. 2. When you hear the ringing tone in the M3000 headset, press the "Call Control" button to answer the call. If you press the "Call Control" button before the headset starts to ring the call may not be answered and an error tone will sound in the headset. Once you hear this tone you can then press the "Call Control" button to pick up the call. To end a call using the M3000 Headset The call can be ended either by pressing the "End / No" key on the 3650 or by pressing the "Call Control" button on the M3000. To place a call using the keypad: 1. Dial the number as normal and press the "Call" key on the 3650. The call can be ended either in the phone or by the headset ­ see above. To place a call using Voice Dialing with the M3000 Headset: NB: Before using the M3000 for voice dialling, ensure that you have followed the instructions in the Nokia 3650 User Guide for voice dialling, and that you have recorded the names of the contacts you wish to call via voice dialling. Place a test call from the 3650 using voice dialling to ensure that it is working before using the M3000 headset. 1. Press and hold the "Call Control" button on the M3000 until you hear a beep in the headset. After a moment you will hear another beep in the headset as a prompt for voice dialling and the phone display will show "Speak Now" 2. State the name of the contact you wish to dial and the call will be placed. To place a call using Last Number redial 1. Double press the "Call Control" button in quick succession. The last number dialled will be called. 3650 M3000 pair rev002 3 24th July 2003 Plantronics Ltd - Released M3000 Pairing Instructions ­ Nokia 6310 Mobile Phone Before pairing the Plantronics M3000 with the Nokia 6310, please ensure both devices are fully charged according to the instructions in the respective User Guides. 1. Turn the Nokia 6310 phone and the Plantronics M3000 headset ON. 2. On the 6310: a) Press "Menu" key, then use the or keys to choose the "Bluetooth" menu. b) Press "Select" again. Use the or keys to choose "On". c) Press "Select". The handset will display "Bluetooth switched on". Bluetooth is now switched on in the phone. 3. On the Plantronics M3000: a) Put the M3000 into pairing mode by press the "Volume Up" & "Call Control" buttons simultaneously until the Indicator light begins to flash alternate green and red. (see M3000 User Instructions). 4. On the Nokia 6310: a) In the "Bluetooth" menu, use the or keys to select "Search for audio accessories" b) In a few moments, the phone will display all nearby Bluetooth devices. Using the or keys, choose "M3000 by Plantronics" and press the "Select" key. c) Enter the 4-digit Passkey 0000 and press the "OK" key. The handset will display "Paired with M3000 by Plantronics" and then "Connected to M3000 by Plantronics". d) Use the "Back" key to return to the main menu Your M3000 headset is now paired and connected with the 6310 phone. If the headset is switched off, it will be disconnected from the 6310. The headset can be reconnected using the 6310 Bluetooth menu, or alternatively, by simply pressing the Call Control button of the headset. However, a menu option must be set on the phone. Before doing this, switch off the headset: a) To allow the headset to connect to the phone automatically, the phone must be configured correctly. Press Menu key, then use the or keys to Select the Bluetooth menu. 6310 M3000 pair rev002 1 24th July 2003 Plantronics Ltd - Released b) In the Bluetooth menu, use the or keys to select View Paired Devices. Press Select. c) The display will show M3000 by ... and possibly other devices. Select M3000 by ... and press Options d) Use the or keys to select Request conn. authorization. Press Select. e) The display will show Yes or No. Use the or keys to choose No and press the Select. f) The phone will display No authorisation required. Return to main menu. Switch on the M3000 headset. Press the Call Control button on the M3000 and the headset will connect to the phone. 6310 M3000 pair rev002 2 24th July 2003 Plantronics Ltd - Released Making and Accepting Calls To accept an in-coming call via the M3000 Headset 1. An in-coming call will cause both the phone and the headset to ring. Note that there may be a delay of a few seconds between the phone ringing and the headset starting to ring. 2. When you hear the ringing tone in the M3000 headset, press the "Call Control" button to answer the call. If you press the "Call Control" button before the headset starts to ring the call may not be answered and an error tone will sound in the headset. Once you hear this tone you can then press the "Call Control" button to pick up the call. To end a call using the M3000 Headset The call can be ended either by pressing the "End Call" key on the 6310 or by pressing the "Call Control" button on the M3000. To place a call using the keypad: 1. Dial the number as normal and press the "Call" key on the 6310. The call can be ended either in the phone or by the headset ­ see above. To place a call using Voice Dialing with the M3000 Headset: NB: Before using the M3000 for voice dialling, ensure that you have followed the instructions in the Nokia 6310 User Guide for voice dialling, and that you have recorded the names of the contacts you wish to call via voice dialling. Place a test call from the 6310 using voice dialling to ensure that it is working before using the M3000 headset. 1. Press and hold the "Call Control" button on the M3000 until you hear a beep in the headset. After a moment you will hear another beep in the headset as a prompt for voice dialling and the phone display will show "Speak Now" 2. State the name of the contact you wish to dial and the call will be placed. To place a call using Last Number redial 1. Double press the "Call Control" button in quick succession. The last number dialled will be called. 6310 M3000 pair rev002 3 24th July 2003 Plantronics Ltd - Released M3000 Pairing Instructions ­ Sony Ericsson T68 Mobile Phone Before pairing the Plantronics M3000 with the Sony Ericsson T68, please ensure both devices are fully charged according to the instructions in the respective User Guides. 1. Turn the Sony Ericsson T68 phone and the Plantronics M3000 headset ON. 2. On the T68, using the Joystick: i. Select "Connect" and press the joystick. ii. Scroll down to "Bluetooth" and press the joystick iii. Scroll down to "Operation Mode", and press the joystick iv. Scroll down to "On" and press the joystick. Bluetooth is now be switched on in the phone. Note: If Bluetooth has already been activated, press the "No" Key (End Call button). 3. On the Plantronics M3000: i. Put the M3000 into pairing mode by press the "Volume Up" & "Call Control" buttons simultaneously until the Indicator light begins to flash alternate green and red. (see M3000 User Instructions). 4. On the Sony Ericsson T68 under "Bluetooth" menu: i. Scroll down to "Paired Devices" and press the joystick ii. The phone will display "Add Device". Press the joystick. iii. Scroll to "Phone initiates" and press the joystick. iv. Scroll to "Headset" and press the joystick. v. The phone will display "Searching" vi. After a few moments the phone will display all the Bluetooth devices within range. Select the "M3000 by Plant" and press the joystick. vii. The phone will request the "Passkey:". Enter 0000 using the keypad then press the joystick. The phone will display "Pairing" followed by "Pairing Successful". viii. The phone will show "Name Tag:" M3000 by Plantronics. Press the joystick. ix. The phone will show "Added to Paired Devices" x. Use the "No" Key (End Call button) to return to the main menu. Your M3000 headset is now paired with the T68 phone. T68 M3000 pair rev002 1 24th July 2003 Plantronics Ltd - Released Making and Accepting Calls To accept an in-coming call via the M3000 Headset 1. An in-coming call will cause both the phone and the headset to ring. Note that there may be a delay of a few seconds between the phone ringing and the headset starting to ring. 2. When you hear the ringing tone in the M3000 headset, press the "Call Control" button to answer the call. If you press the "Call Control" button before the headset starts to ring the call may not be answered and an error tone will sound in the headset. Once you hear this tone you can then press the "Call Control" button to pick up the call. To end a call via the M3000 Headset The call can be ended either by pressing the "Call End / No" key on the T68 or by pressing the "Call Control" button on the M3000. To place a call using the keypad: 1. Dial the number as normal and press the "Call" key on the T68. The audio will automatically be transferred to the headset. To place a call using Voice Dialing with the M3000 Headset: NB: Before using the M3000 for voice dialling, ensure that you have followed the instructions in the Sony Ericsson T68 User Guide for voice dialling, and that you have recorded the names of the contacts you wish to call via voice dialling. Place a test call from the T68 using voice dialling to ensure that it is working before using the M3000 headset. 1. Press and hold the "Call Control" button on the M3000 until you hear a beep in the headset. After a moment you will hear another beep in the headset as a prompt for voice dialling and the phone display will show "After the tone, say a name or command" 2. State the name of the contact you wish to dial and the call will be placed. T68 M3000 pair rev002 2 24th July 2003 Plantronics Ltd - Released M3000 Pairing Instructions ­ Sony Ericsson T610 Mobile Phone Before pairing the Plantronics M3000 with the Sony Ericsson T610, please ensure both devices are fully charged according to the instructions in the respective User Guides. 1. Turn the Sony Ericsson T610 phone and the Plantronics M3000 headset ON. 2. On the T610, Using the upper right key "more", scroll and select "Turn On Bluetooth". Bluetooth is now be switched on in the phone. 3. Using the joystick to scroll and select the following menus: "Connectivity", "Bluetooth", "My Devices" 4. On the Plantronics M3000: i. Put the M3000 into pairing mode by press the "Volume Up" & "Call Control" buttons simultaneously until the Indicator light begins to flash alternate green and red. (see M3000 User Instructions). 5. On the T610: i. New Devices will be displayed. Select "Add" Device. ii. In a few moments, the phone will display all nearby Bluetooth devices. Scroll and select "M3000 by Plantronics" and press the "Select" key. iii. Enter the 4-digit Passkey number 0000 and press the "OK" key. iv. The message "M3000 By Plantronics added to My Devices" will be temporarily displayed by the phone. v. Pairing is complete. Return to the Main Menu. Your M3000 headset is now paired with the T610 phone. T610 M3000 pair rev002 1 24th July 2003 Plantronics Ltd - Released Making and Accepting Calls To accept an in-coming call via the M3000 Headset 1. An in-coming call will cause both the phone and the headset to ring. Note that there may be a delay of a few seconds between the phone ringing and the headset starting to ring. 2. When you hear the ringing tone in the M3000 headset, press the "Call Control" button to answer the call. If you press the "Call Control" button before the headset starts to ring the call may not be answered and an error tone will sound in the headset. Once you hear this tone you can then press the "Call Control" button to pick up the call. To end a call via the M3000 Headset The call can be ended either by pressing the "Call End / No" key on the T610 or by pressing the "Call Control" button on the M3000. To place a call using the keypad: 1. Dial the number as normal and press the "Call" key on the T610. The audio will automatically be transferred to the headset. To place a call using Voice Dialing with the M3000 Headset: NB: Before using the M3000 for voice dialling, ensure that you have followed the instructions in the Sony Ericsson T610 User Guide for voice dialling, and that you have recorded the names of the contacts you wish to call via voice dialling. Place a test call from the T610 using voice dialling to ensure that it is working before using the M3000 headset. 1. Press and hold the "Call Control" button on the M3000 until you hear a beep in the headset. After a moment you will hear another beep in the headset as a prompt for voice dialling and the phone display will show "After the tone, say a name or command" 2. State the name of the contact you wish to dial and the call will be placed. Known Issues 1. The T610, as released (Software Version R1A081 prgCXC125-566_EU_2 R1A081 prgCXC125-566_TAE), does NOT support low power modes whilst using the handsfree. Therefore, the standby time with this device will be very poor (about 10 hours, rather than 200 hours). This issue can be fixed by returning your phone to an authorised Sony-Ericsson service centre, and is free if your phone is under warranty. T610 M3000 pair rev002 2 24th July 2003 Plantronics Ltd - Released M3000 Pairing Instructions - Siemens S56 Mobile Phone Before pairing the Plantronics M3000 with the Siemens S56, please ensure both devices are fully charged according to the instructions in the respective User Guides. 1. Turn the Siemens S56 phone and the Plantronics M3000 headset ON. 2. On the S56: i. Press the right key under "Menu" in the display ii. Move the cursor to the "SETUP" icon and press "SELECT" iii. Use the cursor key to move down to "Connectivity" and press "SELECT" iv. Use the cursor key to move down to "Bluetooth" and press "OPTIONS" v. Use the cursor keys to highlight "Activate Bluetooth" and press "SELECT" Bluetooth will now be switched on in the phone. Note: if Bluetooth has already been activated the only option presented will be to "Deactivate". Press the "No / Cancel" or "End Call" key and proceed to the next step. 3. On the Plantronics M3000: i. Put the M3000 into pairing mode by press the "Volume Up" & "Call Control" buttons simultaneously until the Indicator light begins to flash alternate green and red. (see M3000 User Instructions). 4. On the Siemens S56: i. Press the "OPTIONS" key ii. Use the cursor key to move down to "Search for..." and press the "ACCESS" key iii. After a few moments the phone will display all the Bluetooth devices within range. Use the cursor key to highlight "M3000 by Plantro..." and press "SELECT" iv. The S56 will prompt you to enter the M3000 PIN code. Enter 0000, then Press "OK". v. The display will show "Handsfree Trusted" and then return to the "Bluetooth" option in the "Connectivity" menu. You can now press the "No / Cancel" key to return to the main display. Your M3000 headset is now paired with the S56 phone. S55 M3000 pair rev001 1 3rd July 2003 Plantronics Ltd - Released Each time the phone is switched on, if the headset is also on, the phone will automatically connect to the headset. Making and Accepting Calls To accept an in-coming call via the M3000 Headset 1. An in-coming call will cause both the phone and the headset to ring. Note that there may be a delay of a few seconds between the phone ringing and the headset starting to ring. 2. When you hear the ringing tone in the M3000 headset, press the "Call Control" button to answer the call. If you press the "Call Control" button before the headset starts to ring the call may not be answered and an error tone will sound in the headset. Once you hear this tone you can then press the "Call Control" button to pick up the call. To end a call via the M3000 Headset The call can be ended either by pressing the "End / No" key on the S56 or by pressing the "Call Control" button on the M3000. To place a call using the keypad: 1. Dial the number as normal and press the "Call" key on the S56. 2. Press the "Call Control" button on the M3000 to transfer the sound to the headset. To place a call using Voice Dialing with the M3000 Headset: NB: Before using the M3000 for voice dialling, ensure that you have followed the instructions in the Siemens S56 User Guide for voice dialling, and that you have recorded the names of the contacts you wish to call via voice dialling. Place a test call from the S56 using voice dialling to ensure that it is working before using the M3000 headset. 1. Press and hold the "Call Control" button on the M3000 until you hear a beep in the headset. After a moment you will hear another beep in the headset as a prompt for voice dialling and the phone display will show "Speak Now" 2. State the name of the contact you wish to dial and the call will be placed. To place a call using Last Number redial 1. Double press the "Call Control" button in quick succession. The last number dialled will be called. S55 M3000 pair rev001 2 3rd July 2003 Plantronics Ltd - Released M3000 Pairing Instructions - Siemens S55 Mobile Phone Before pairing the Plantronics M3000 with the Siemens S55, please ensure both devices are fully charged according to the instructions in the respective User Guides. 1. Turn the Siemens S55 phone and the Plantronics M3000 headset ON. 2. On the S55: i. Press the right key under "Menu" in the display ii. Move the cursor to the "SETUP" icon and press "SELECT" iii. Use the cursor key to move down to "Connectivity" and press "SELECT" iv. Use the cursor key to move down to "Bluetooth" and press "OPTIONS" v. Use the cursor keys to highlight "Activate Bluetooth" and press "SELECT" Bluetooth will now be switched on in the phone. Note: if Bluetooth has already been activated the only option presented will be to "Deactivate". Press the "No / Cancel" or "End Call" key and proceed to the next step. 3. On the Plantronics M3000: i. Put the M3000 into pairing mode by press the "Volume Up" & "Call Control" buttons simultaneously until the Indicator light begins to flash alternate green and red. (see M3000 User Instructions). 4. On the Siemens S55: i. Press the "OPTIONS" key ii. Use the cursor key to move down to "Search for..." and press the "ACCESS" key iii. After a few moments the phone will display all the Bluetooth devices within range. Use the cursor key to highlight "M3000 by Plantro..." and press "SELECT" iv. The S55 will prompt you to enter the M3000 PIN code. Enter 0000, then Press "OK". v. The display will show "Handsfree Trusted" and then return to the "Bluetooth" option in the "Connectivity" menu. You can now press the "No / Cancel" key to return to the main display. Your M3000 headset is now paired with the S55 phone. S55 M3000 pair rev001 1 3rd July 2003 Plantronics Ltd - Released Each time the phone is switched on, if the headset is also on, the phone will automatically connect to the headset. Making and Accepting Calls To accept an in-coming call via the M3000 Headset 1. An in-coming call will cause both the phone and the headset to ring. Note that there may be a delay of a few seconds between the phone ringing and the headset starting to ring. 2. When you hear the ringing tone in the M3000 headset, press the "Call Control" button to answer the call. If you press the "Call Control" button before the headset starts to ring the call may not be answered and an error tone will sound in the headset. Once you hear this tone you can then press the "Call Control" button to pick up the call. To end a call via the M3000 Headset The call can be ended either by pressing the "End / No" key on the S55 or by pressing the "Call Control" button on the M3000. To place a call using the keypad: 1. Dial the number as normal and press the "Call" key on the S55. 2. Press the "Call Control" button on the M3000 to transfer the sound to the headset. To place a call using Voice Dialing with the M3000 Headset: NB: Before using the M3000 for voice dialling, ensure that you have followed the instructions in the Siemens S55 User Guide for voice dialling, and that you have recorded the names of the contacts you wish to call via voice dialling. Place a test call from the S55 using voice dialling to ensure that it is working before using the M3000 headset. 1. Press and hold the "Call Control" button on the M3000 until you hear a beep in the headset. After a moment you will hear another beep in the headset as a prompt for voice dialling and the phone display will show "Speak Now" 2. State the name of the contact you wish to dial and the call will be placed. To place a call using Last Number redial 1. Double press the "Call Control" button in quick succession. The last number dialled will be called. S55 M3000 pair rev001 2 3rd July 2003 Plantronics Ltd - Released M3000 Pairing Instructions ­ Sony Ericsson P800 Mobile Phone Before pairing the Plantronics M3000 with the Sony Ericsson P800, please ensure both devices are fully charged according to the instructions in the respective User Guides. 1. Turn the Sony Ericsson P800 phone and the Plantronics M3000 headset ON. 2. On the P800, open the flip and using the Jog Dial (rotate and press) and stylus: i. Scroll to "Control Panel" and press the jog dial. ii. Select "Connections" using the stylus iii. Scroll down to "Bluetooth" and press the jog dial iv. Select "Settings" using the stylus v. Using the stylus, change the "Operation Mode" to "On" vi. Using the stylus, select "Done" Bluetooth is now be switched on in the phone. Note: If Bluetooth has already been activated, press "Done" anyway. 3. On the Plantronics M3000: i. Put the M3000 into pairing mode by press the "Volume Up" & "Call Control" buttons simultaneously until the Indicator light begins to flash alternate green and red. (see M3000 User Instructions). 4. On the Sony Ericsson P800: i. Scroll down to "Bluetooth" and press the jog dial. ii. Using the stylus, select "Devices" iii. Using the stylus, select "Add" iv. The phone will display "Searching". v. After a few moments the phone will display all the Bluetooth devices within range. Using the stylus, select the "M3000 by Plantronics". vi. The phone will display "Bonding in Progress" vii. The phone will request the "Passkey:". Enter 0000 using the keypad then press the jog dial. The phone will display "Bonding in Progress" followed by "Bonding Successful". viii. Using the stylus, select "Done" Your M3000 headset is now paired with the P800 phone. P800 M3000 pair rev001 1 3rd July 2003 Plantronics Ltd - Released Making and Accepting Calls To accept an in-coming call via the M3000 Headset 1. An in-coming call will cause both the phone and the headset to ring. Note that there may be a delay of a few seconds between the phone ringing and the headset starting to ring. 2. When you hear the ringing tone in the M3000 headset, press the "Call Control" button to answer the call. If you press the "Call Control" button before the headset starts to ring, the call may not be answered and an error tone will sound in the headset. Once you hear this tone you can then press the "Call Control" button to pick up the call. To end a call via the M3000 Headset The call can be ended either by pressing "Call End" on the P800 or by pressing the "Call Control" button on the M3000. To place a call using the keypad: 1. Dial the number as normal and press the "Call" key on the P800. 2. Press the "Call Control" button on the M3000 to transfer the sound to the headset. To place a call using Voice Dialing with the M3000 Headset: NB: Before using the M3000 for voice dialling, ensure that you have followed the instructions in the Sony Ericsson P800 User Guide for voice dialling, and that you have recorded the names of the contacts you wish to call via voice dialling. Place a test call from the P800 using voice dialling to ensure that it is working before using the M3000 headset. 1. Press the "Call Control" button on the M3000, you hear a beep in the headset. After a moment you will hear another beep in the headset as a prompt for voice dialling and the phone display will show "Sound Transferred to Headset" 2. State the name of the contact you wish to dial and the call will be placed. P800 M3000 pair rev001 2 3rd July 2003 Plantronics Ltd - Released M3000 Pairing Instructions ­ Nokia 8910i Mobile Phone Before pairing the Plantronics M3000 with the Nokia 8910i, please ensure both devices are fully charged according to the instructions in the respective User Guides. 1. Turn the Nokia 8910i phone and the Plantronics M3000 headset ON. 2. On the 8910i: a) Press Menu key, then use the or keys to choose the Connectivity menu. Press Select. b) Use the or keys to choose the Bluetooth menu. Press Select. c) Press Select again. Use the or keys to choose On. d) Press Select. The handset will display Bluetooth switched on. Bluetooth will now be switched on in the phone. 3. On the Plantronics M3000: a) Put the M3000 into pairing mode by press the "Volume Up" & "Call Control" buttons simultaneously until the Indicator light begins to flash alternate green and red. (see M3000 User Instructions). 4. On the Nokia 8910i: a) In the Bluetooth menu, use the or keys to select Search for audio accessories b) In a few moments, the phone will display all nearby Bluetooth devices. Using the or keys, choose M3000 by Plantronics and press the Select key. c) Enter the 4-digit Passkey 0000 and press the OK key. The handset will display Paired with M3000 by Plantronics and then Connected to M3000 by Plantronics. Your M3000 headset is now paired and connected with the 8910i phone. If the headset is switched off, it will be disconnect from the 8910i. The headset can be reconnected using the 8910i Bluetooth menu, or alternatively, by simply pressing the Call Control button of the headset. However, a menu option must be set on the phone. Before doing this, switch off the headset: a) To allow the headset to connect to the phone automatically, the phone must be configured correctly. Press Menu key, then use the or keys to Select the Bluetooth menu. b) In the Bluetooth menu, use the or keys to select View Paired Devices. Press Select. 24th July 2003 8910i M3000 pair rev002 1 Plantronics Ltd - Released c) The display will show M3000 by ... and possibly other devices. Select M3000 by ... and press Options d) Use the or keys to select Request conn. authorization. Press Select. e) The display will show Yes or No. Use the or keys to choose No and press the Select. f) The phone will display No authorisation required. Return to main menu. Switch on the M3000 headset. Press the Call Control button on the M3000 and the headset will connect to the phone. 8910i M3000 pair rev002 2 24th July 2003 Plantronics Ltd - Released Making and Accepting Calls To accept an in-coming call via the M3000 Headset 1. An in-coming call will cause both the phone and the headset to ring. Note that there may be a delay of a few seconds between the phone ringing and the headset starting to ring. 2. When you hear the ringing tone in the M3000 headset, press the "Call Control" button to answer the call. If you press the "Call Control" button before the headset starts to ring the call may not be answered and an error tone will sound in the headset. Once you hear this tone you can then press the "Call Control" button to pick up the call. To end a call using the M3000 Headset The call can be ended either by pressing the "End / No" key on the 8910i or by pressing the "Call Control" button on the M3000. To place a call using the keypad: 1. Dial the number as normal and press the "Call" key on the 8910i. The call can be ended either in the phone or by the headset ­ see above. To place a call using Voice Dialing with the M3000 Headset: NB: Before using the M3000 for voice dialling, ensure that you have followed the instructions in the Nokia 8910i User Guide for voice dialling, and that you have recorded the names of the contacts you wish to call via voice dialling. Place a test call from the 8910i using voice dialling to ensure that it is working before using the M3000 headset. 1. Press and hold the "Call Control" button on the M3000 until you hear a beep in the headset. After a moment you will hear another beep in the headset as a prompt for voice dialling and the phone display will show "Speak Now" 2. State the name of the contact you wish to dial and the call will be placed. To place a call using Last Number redial 1. Double press the "Call Control" button in quick succession. The last number dialled will be called. 8910i M3000 pair rev002 3 24th July 2003 Plantronics Ltd - Released M3000 Pairing Instructions ­ Nokia 8910 Mobile Phone Before pairing the Plantronics M3000 with the Nokia 8910, please ensure both devices are fully charged according to the instructions in the respective User Guides. 1. Turn the Nokia 8910 phone and the Plantronics M3000 headset ON. 2. On the 8910: a) Press Menu key, then use the or keys to choose the Bluetooth menu. Note: If Bluetooth has already been activated, move onto b) Press Select. Use the or keys to choose On. c) Press Select. The handset will display Bluetooth switched on. Bluetooth will now be switched on in the phone. 3. On the Plantronics M3000: a) Put the M3000 into pairing mode by press the "Volume Up" & "Call Control" buttons simultaneously until the Indicator light begins to flash alternate green and red. (see M3000 User Instructions). 4. On the Nokia 8910: a) In the Bluetooth menu, use the or keys to select Search for audio accessories b) In a few moments, the phone will display all nearby Bluetooth devices. Using the or keys, choose M3000 by Plantronics and press the Select key. c) Enter the 4-digit Passkey 0000 and press the OK key. The handset will display Paired with M3000 by Plantronics Your M3000 headset is now paired and connected with the 8910 phone. If the headset is switched off, it will be disconnect from the 8910. The headset can be reconnected using the 8910 Bluetooth menu, or alternatively, by simply pressing the Call Control button of the headset. However, a menu option must be set on the phone. Before doing this, switch off the headset: a) To allow the headset to connect to the phone automatically, the phone must be configured correctly. Press Menu key, then use the or keys to Select the Bluetooth menu. b) In the Bluetooth menu, use the or keys to select View Paired Devices. Press Select. step 3 below. 8910 M3000 pair rev001 1 3rd July 2003 Plantronics Ltd - Released c) The display will show M3000 by ... and possibly other devices. Select M3000 by ... and press Options d) Use the or keys to select Request conn. authorization. Press Select. e) The display will show Yes or No. Use the or keys to choose No and press the Select. f) The phone will display No authorisation required. Return to main menu. Press the Call Control button on the M3000 and the headset will connect to the phone. 8910 M3000 pair rev001 2 3rd July 2003 Plantronics Ltd - Released Making and Accepting Calls To accept an in-coming call via the M3000 Headset 1. An in-coming call will cause both the phone and the headset to ring. Note that there may be a delay of a few seconds between the phone ringing and the headset starting to ring. 2. When you hear the ringing tone in the M3000 headset, press the "Call Control" button to answer the call. If you press the "Call Control" button before the headset starts to ring the call may not be answered and an error tone will sound in the headset. Once you hear this tone you can then press the "Call Control" button to pick up the call. To end a call using the M3000 Headset The call can be ended either by pressing the "End / No" key on the 8910 or by pressing the "Call Control" button on the M3000. To place a call using the keypad: 1. Dial the number as normal and press the "Call" key on the 8910. The call can be ended either in the phone or by the headset ­ see above. To place a call using Voice Dialing with the M3000 Headset: NB: Before using the M3000 for voice dialling, ensure that you have followed the instructions in the Nokia 8910 User Guide for voice dialling, and that you have recorded the names of the contacts you wish to call via voice dialling. Place a test call from the 8910 using voice dialling to ensure that it is working before using the M3000 headset. 1. Press and hold the "Call Control" button on the M3000 until you hear a beep in the headset. After a moment you will hear another beep in the headset as a prompt for voice dialling and the phone display will show "Speak Now" 2. State the name of the contact you wish to dial and the call will be placed. To place a call using Last Number redial 1. Double press the "Call Control" button in quick succession. The last number dialled will be called. 8910 M3000 pair rev001 3 3rd July 2003 Plantronics Ltd - Released M3000 Pairing Instructions. Philips Fisio 825 Mobile Phone Before pairing the Plantronics M3000 with the Philips Fisio 825, please ensure both devices are fully charged according to the instructions in the respective User Guides. 1. Turn the Philips Fisio 825 phone and the Plantronics M3000 headset ON. 2. On the Philips Fisio 825: i. Press the "Menu" key, and using the left arrow key (number 4) four times, move to "BLUETOOTH". Press key 5 to select. ii. Using the left arrow key (number 4) one time, move to "BLUETOOTH SETTING". Press key 5 to select. iii. "BLUETOOTH ON / OFF" will be displayed. Press key 5 to select. iv. Use the left arrow key (number 4) or right arrow key (number 6) to select "ALWAYS ON". Press key 5 to select. v. Press "Menu" to return to main display. 3. On the Plantronics M3000: i. Put the M3000 into pairing mode by press the "Volume Up" & "Call Control" buttons simultaneously until the Indicator light begins to flash alternate green and red. (see M3000 User Instructions). 4. On the Philips Fisio 825: i. Press the "Menu" key and using the left arrow key (number 4) four times, move to "BLUETOOTH". Press key 5 to select. ii. "BLUETOOTH HEADSET" will be displayed. Press key 5 to select. iii. Press the "OK" key or key 5 to detect the M3000 headset. iv. v. vi. In a few moments, the phone will display all nearby Bluetooth devices. Select "M3000 by Plantronics" using the up/down keys. Press 5 to initiate pairing. The phone will display "PLEASE WAIT". When "PAIRING" is displayed in the top left corner of the display, enter the 0000 Passkey number and press the OK key. Press "Menu" to return to main display. Your M3000 headset is now paired with the Fisio 825 phone. Fisio 825 M3000 pair rev001 1 3rd July 2003 Plantronics Ltd - Released Making and Accepting Calls To accept an in-coming call via the M3000 Headset 1. An in-coming call will cause both the phone and the headset to ring. Note that there may be a delay of a few seconds between the phone ringing and the headset starting to ring. 2. When you hear the ringing tone in the M3000 headset, press the "Call Control" to answer the call. If you press the "Call Control" button before the headset starts to ring the call will not be answered and an error tone will sound in the M3000. Once you hear this tone you can then press "Call Control" button to answer the call. To place a call using the keypad: 1. Dial the number as normal and press the "Call" key on the Fisio 825. 2. Press the M3000 "Call Control" button to transfer the sound to the headset. To end a call via the M3000 Headset The call can be ended either by pressing the "End Call" key on the Fisio 825 or by pressing the M3000 "Call Control" button on the M3000. To place a call using Voice Dialing with the M3000 Headset: NB: Before using the M3000 for voice dialling, ensure that you have followed the instructions in the Philips Fisio 825 User Guide for voice dialling, and that you have recorded the names of the contacts you wish to call via voice dialling. Place a test call from the Fisio 825 using voice dialling to ensure that it is working before using the M3000 headset. 1. Briefly press the "Call Control" button on the M3000 until you hear a beep in the headset. After a moment you will hear another beep in the headset as a prompt for voice dialling and the phone display will show "Speak Now". 2. Repeat the name of the contact you wish to dial and the call will be placed. Fisio 825 M3000 pair rev001 2 3rd July 2003 Plantronics Ltd - Released M3000 Pairing Instructions ­ Nokia 6310i Mobile Phone Before pairing the Plantronics M3000 with the Nokia 6310i, please ensure both devices are fully charged according to the instructions in the respective User Guides. 1. Turn the Nokia 6310i phone and the Plantronics M3000 headset ON. 2. On the 6310i: a) Press "Menu" key, then use the or keys to choose the "Bluetooth" menu. b) Press "Select" again. Use the or keys to choose "On". c) Press "Select". The handset will display "Bluetooth switched on". Bluetooth is now switched on in the phone. 3. On the Plantronics M3000: a) Put the M3000 into pairing mode by press the "Volume Up" & "Call Control" buttons simultaneously until the Indicator light begins to flash alternate green and red. (see M3000 User Instructions). 4. On the Nokia 6310i: a) In the "Bluetooth" menu, use the or keys to select "Search for audio accessories" b) In a few moments, the phone will display all nearby Bluetooth devices. Using the or keys, choose "M3000 by Plantronics" and press the "Select" key. c) Enter the 4-digit Passkey 0000 and press the "OK" key. The handset will display "Paired with M3000 by Plantronics" and then "Connected to M3000 by Plantronics". d) Use the "Back" key to return to the main menu Your M3000 headset is now paired and connected with the 6310i phone. If the headset is switched off, it will be disconnected from the 6310i. The headset can be reconnected using the 6310i Bluetooth menu, or alternatively, by simply pressing the Call Control button of the headset. However, a menu option must be set on the phone. Before doing this, switch off the headset: a) To allow the headset to connect to the phone automatically, the phone must be configured correctly. Press Menu key, then use the or keys to Select the Bluetooth menu. 6310i M3000 pair rev002 1 24th July 2003 Plantronics Ltd - Released b) In the Bluetooth menu, use the or keys to select View Paired Devices. Press Select. c) The display will show M3000 by ... and possibly other devices. Select M3000 by ... and press Options d) Use the or keys to select Request conn. authorization. Press Select. e) The display will show Yes or No. Use the or keys to choose No and press the Select. f) The phone will display No authorisation required. Return to main menu. Switch on the M3000 headset. Press the Call Control button on the M3000 and the headset will connect to the phone. 6310i M3000 pair rev002 2 24th July 2003 Plantronics Ltd - Released Making and Accepting Calls To accept an in-coming call via the M3000 Headset 1. An in-coming call will cause both the phone and the headset to ring. Note that there may be a delay of a few seconds between the phone ringing and the headset starting to ring. 2. When you hear the ringing tone in the M3000 headset, press the "Call Control" button to answer the call. If you press the "Call Control" button before the headset starts to ring the call may not be answered and an error tone will sound in the headset. Once you hear this tone you can then press the "Call Control" button to pick up the call. To end a call using the M3000 Headset The call can be ended either by pressing the "End Call" key on the 6310i or by pressing the "Call Control" button on the M3000. To place a call using the keypad: 1. Dial the number as normal and press the "Call" key on the 6310i. The call can be ended either in the phone or by the headset ­ see above. To place a call using Voice Dialing with the M3000 Headset: NB: Before using the M3000 for voice dialling, ensure that you have followed the instructions in the Nokia 6310i User Guide for voice dialling, and that you have recorded the names of the contacts you wish to call via voice dialling. Place a test call from the 6310i using voice dialling to ensure that it is working before using the M3000 headset. 1. Press and hold the "Call Control" button on the M3000 until you hear a beep in the headset. After a moment you will hear another beep in the headset as a prompt for voice dialling and the phone display will show "Speak Now" 2. State the name of the contact you wish to dial and the call will be placed. To place a call using Last Number redial 1. Double press the "Call Control" button in quick succession. The last number dialled will be called. 6310i M3000 pair rev002 3 24th July 2003 Plantronics Ltd - Released M3000 Pairing Instructions ­ Sony Ericsson T68i Mobile Phone Before pairing the Plantronics M3000 with the Sony Ericsson T68i, please ensure both devices are fully charged according to the instructions in the respective User Guides. 1. Turn the Sony Ericsson T68i phone and the Plantronics M3000 headset ON. 2. On the T68i, using the Joystick: i. Select "Connect" and press the joystick. ii. Scroll down to "Bluetooth" and press the joystick iii. Scroll down to "Options" and press the joystick iv. Scroll down to "Operation Mode", and press the joystick v. Scroll down to "On" and press the joystick. vi. Press the "No" or "End Call" button to return to the Bluetooth menu Bluetooth is now be switched on in the phone. 3. On the Plantronics M3000: i. Put the M3000 into pairing mode by press the "Volume Up" & "Call Control" buttons simultaneously until the Indicator light begins to flash alternate green and red. (see M3000 User Instructions). 4. On the Sony Ericsson T68i: i. Scroll down to "Discover" and press the joystick. ii. The phone will display "Searching" iii. After a few moments the phone will display all the Bluetooth devices within range. Select the "M3000 by Plantronics" and press the joystick. iv. The phone will display "Add to paired". Press the joystick v. The phone will request the "Passkey:". Enter 0000 using the keypad then press the joystick. The phone will display "M3000 by Plantronics Pairing" followed by "Pairing Succeeded" and then "M3000 added to paired devices". vi. The phone will show "Name Tag: M3000 by Plantronics". Press the joystick. vii. Use the "No" Key (End Call button) to return to the main menu. viii. Your M3000 headset is now paired with the T68i phone. T68i M3000 pair rev002 1 24th July 2003 Plantronics Ltd - Released Making and Accepting Calls To accept an in-coming call via the M3000 Headset 1. An in-coming call will cause both the phone and the headset to ring. Note that there may be a delay of a few seconds between the phone ringing and the headset starting to ring. 2. When you hear the ringing tone in the M3000 headset, press the "Call Control" button to answer the call. If you press the "Call Control" button before the headset starts to ring the call may not be answered and an error tone will sound in the headset. Once you hear this tone you can then press the "Call Control" button to pick up the call. To end a call via the M3000 Headset The call can be ended either by pressing the "Call End / No" key on the T68i or by pressing the "Call Control" button on the M3000. To place a call using the keypad: 1. Dial the number as normal and press the "Call" key on the T68i. The audio will automatically be transferred to the headset. To place a call using Voice Dialing with the M3000 Headset: NB: Before using the M3000 for voice dialling, ensure that you have followed the instructions in the Sony Ericsson T68i User Guide for voice dialling, and that you have recorded the names of the contacts you wish to call via voice dialling. Place a test call from the T68i using voice dialling to ensure that it is working before using the M3000 headset. 1. Press and hold the "Call Control" button on the M3000 until you hear a beep in the headset. After a moment you will hear another beep in the headset as a prompt for voice dialling and the phone display will show "After the tone, say a name or command" 3. State the name of the contact you wish to dial and the call will be placed. T68i M3000 pair rev002 2 24th July 2003