User manual PLANTRONICS PULSAR 260

USER GUIDE USER GUIDE Pl antronics PulsarTM 260 .................................................................................. PULSAR 260 Stereo Bluetooth headSet TM ® STEREO BLUETOOTH HEADSET WelCome This User Guide provides instructions on the setup and usage of the Plantronics PulsarTM 260 Bluetooth® Headset. Before getting started, please review the safety booklet included in your package. For additional help, service or support information, refer to product warranty card, Troubleshooting on page 9 or visit www.plantronics.com. Table of ConTenTs Package Contents and Feataures Charging Powering Indicator Lights Pairing Making/Answering/Ending Calls Wearing Options Powered Speaker & Stereo Uses Pendant Controls Headset Controls Troubleshooting System Reset Product Specifications Warranty Technical Assistance Regulatory Information Warnings 3 4 4 4 5 5 6 6 7 8 9 9 10 10 11 11 12 Register Your Product online Visit www.plantronics.com/productregistration to register your product online so we can provide you with the best possible service and technical support. | PaCkage ConTenTs & feaTuRes Pulsar 260 Headset Microphone with call control button Sound-isolating earbuds 2.5mm plug stereo bluetooth Pendant Mini-USB port Indicator light Power on/off/Pairing 2.5mm port Detachable clip Audio-out cable AC charger Lanyard Pendant Controls: Mute/Play/Pause Volume up Power on/off/Pairing Volume down Track forward Track back | CHaRging You must charge for 3 hours before first use. To charge, connect AC charger to pendant mini-USB socket. Pendant indicator light flashes red when charging and changes to solid blue when fully charged. PoWeRing on/off Press and hold power on/off switch for >2 seconds. PenDanT inDiCaToR ligHTs Action Charging Fully charged Light Flashes Red Solid blue 3 red flashes = Power/battery status 2 red flashes = 1 red flash = Pairing/connect Bluetooth pendant connected to headset Flashes red and blue Flashes blue NOTE: Flashes red when headset is initially powered on. | PaiRing To pair pendant with phone: Begin with pendant powered on. 1. Press and hold both the mute/play/pause button and the power on/off/pairing button simultaneously. When the indicator light flashes red and blue, release buttons. 2. While pendant is flashing red and blue, use the phone menu to search for Bluetooth devices and select "260 Plantronics." 3. When prompted for passkey, enter 0000. Pendant flashes blue when paired successfully. For set up and pairing instructions with Bluetooth devices other than mobile phones, please consult your Bluetooth device user guide. 1 2 M2500 Plantronics 3 Enter Passkey 260Plantronics M3000 Plantronics 0000 making/ansWeRing/enDing Calls To make a call: Dial on phone; call transfers automatically to headset. To answer or end a call: Briefly press call control button on headset. To adjust volume: Short press + or ­ buttons on pendant for incremental change, hold for continuous change. | WeaRing oPTions Pulsar 260 can be worn in two ways: · Clipped to your belt or clothing · Around your neck using the lanyard PoWeReD sPeakeR & sTeReo uses For public listening you can connect the stereo Bluetooth pendant directly to powered speakers or your home stereo with the included audio-out cable (provided your speakers/ home stereo is fitted with a Line-in or Auxiliary 3.5mm audio socket). Please consult your equipment guide. 1. Ensure the stereo Bluetooth pendant and your speakers/home stereo are powered off. 2. Connect the audio-out cable 2.5mm plug to the stereo Bluetooth pendant and the 3.5mm plug to to the powered speakers/home stereo Line-in or Auxiliary 3.5mm audio socket as shown below. 3. Power on both the stereo Bluetooth pendant and your speakers/home stereo. | PenDanT ConTRols Power on/off Key Feature Power on/off Action Short press Tone No tone Track forward and back* Mute call/audio Play and pause* Adjusting volume Short press to skip to next track or to go back to previous track Short press to mute/unmute Short press to pause/ resume audio Short press High tone Repeating low tone every 60 seconds High tone Mid tone for each adjustment, double low tone at limit *Only works if Bluetooth device supports Bluetooth Audio/Video Remote Control Profile (AVRCP). | HeaDseT ConTRols Key Feature Making/answering/ending calls Switching an active call from headset to phone or phone to headset Action Short key press Tone High tone Long key press High tone followed by low tone Hands-free features Key Feature Activate last number redial Activate voice dial Action Double short key press Tone High tone for each key press High tone followed by low tone High tone followed by low tone Long key press Call reject Long key press Features must be supported by Bluetooth device or service provider. | TRoublesHooTing Problem My headset does not work with my phone. Callers cannot hear me. Solution · See page 5 "Pairing." · Perform a reset on Pulsar 260 as described below. · Headset is muted. Press the mute button on the pendant to unmute the microphone. · Be sure pendant is powered on and headset is paired with audio device. See page 5 "Pairing. " Ensure that microphone is pointing towards your mouth. · Pendant is turned off. Check the indicator light for status. · Headset is out of range. Walk to within 10 metres of the phone and check the Bluetooth link on your phone's display. · Battery is dead. Charge your battery using the AC charger supplied. · Listening volume is too low. Press the volume up button to increase the sound heard in the headset. · Pendant must be turned on and connected to the powered speakers/Hi-Fi with the audio-out cable. · Check music player on Bluetooth phone is switched on and Pulsar 260 is the active Bluetooth device. Callers say my voice is too quiet. I cannot hear caller/dial tone or audio sound. I cannot hear music from my powered speakers/ Hi-Fi when using the audioout cable. sYsTem ReseT A reset button is located (recessed) behind the clothing clip. To reset: 1. Remove clip as shown at right. 2. Press and release button using a pen. 1 2 2 | PRoDuCT sPeCifiCaTions Listen Time* Talk Time* Standby Time* Charge Time Range Headset and Pendant Weight Power Requirements Battery Type Speaker Frequency Response Impedance Distortion Version Up to 7 hours Up to 9 hours Up to 200 hours 3 hours Bluetooth standard 10 metres 25 grams 5VDC - 300 mA Lithium Ion Polymer · Telephony 300 Hz to 3600 Hz (CVSD) · Stereo Audio 20 Hz to 20 kHz(16-bit 48kHz SBC Coding) 32 +-4 Ohms x1 kHz <5% to 19 kHz Bluetooth 2.0 Supports Bluetooth Hands-Free and Headset Profiles, Advanced Audio Distribution Profile (A2 DP), Audio/Video Remote Control Profile (AVRCP), and Generic Audio/Video Distribution Profile (GAVDP). For stereo sound, Bluetooth enabled devices must support the Advanced Audio Distribution Profile (A2DP). *Performance may vary by device. WaRRanTY limiTeD WaRRanTY · This warranty covers defects in materials and workmanship of products manufactured, sold or certified by Plantronics which were purchased and used in the United States. · The warranty lasts for one year from the date of purchase of the products. · This warranty extends to you only if you are the end user with the original purchase receipt. · We will at our option, repair or replace the products that do not conform to the warranty. We may use functionally equivalent reconditioned/refurbished/ remanufactured/pre-owned or new products or parts. · To obtain service in the U.S., contact Plantronics at (866) 363-BLUE (2583). · THIS IS PLANTRONICS' COMPLETE WARRANTY FOR THE PRODUCTS. · This warranty gives you specific legal rights, and you may also have other rights that vary from state to state. Please contact your dealer or our service center for the full details of our limited warranty, including items not covered by this limited warranty. 10 | TeCHniCal assisTanCe Visit our Web site at www.plantronics.com/support for technical support including frequently asked questions, compatibility and accessibility information. Plantronics Technical Assistance Center (TAC) is also ready to assist you on 866-363-BLUE (2583). RegulaToRY noTiCes fCC ReQuiRemenTs PaRT 15 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception which can be determined by turning the radio or television off and on, the user is encouraged to try to correct interference by one or more of the following measures: 1. Reorient or relocate the receiving antenna. 2. Increase the separation between the equipment and receiver. 3. Connect the equipment into an outlet on another circuit. 4. Consult the dealer or an experienced radio/TV technician for help. eXPosuRe To Rf RaDiaTion The internal wireless radio operates within the guidelines found in radio frequency safety standards and recommendations, which reflect the consensus of the scientific community. Independent studies have shown that the internal wireless radio is safe for use by consumers. Visit www.plantronics.com for more information. NOTE: Modifications not expressly approved by Plantronics, Inc. could void the user's authority to operate the equipment. | 11 WaRnings Use of a headset that covers both ears will impair your ability to hear other sounds. Use of such a headset while operating a motor vehicle or riding a bicycle may create a serious hazard to you and/or others, and is illegal in most regions. Do not use headphones / headsets at high volumes for an extended period of time. Doing so can cause hearing loss. Always listen at moderate levels. Plantronics, Inc. 345 Encinal Street Santa Cruz, CA 95060 USA (800) 544-4660 www.plantronics.com ©2006 Plantronics, Inc. All rights reserved. Plantronics, the logo design, Plantronics Sound Innovation and Pulsar are trademarks or registered trademarks of Plantronics, Inc. The Bluetooth® word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Plantronics, Inc. is under license. Patents Pending. Printed in USA. (10-06) 1 |