blue wave speaker connections 4 ch amp PLA885·PLA1085 2 CH Stereo Output Mode with Mono Bridged Subwoofer Output pla885 pla1085 MINIMUM SPEAKER IMPEDANCE 4 OHMS! L SPEAKERS R SUBWOOFER 28 blue wave speaker connections R 5 ch amps PLA1585 5 CH Output Mode FRONT speakers L pla1585 29 L R REAR speakers SUBWOOFER All Pyle products are carefully constructed and thoroughly tested before shipment. Products purchased in the USA are warranted to be free of defects in material and workmanship for two (2) years from the date of purchase. This warranty is limited to the original retail purchase. Should the product fail due to factory defects in material or workmanship, your unit will be repaired or replaced at the sole discretion of Pyle. To obtain warranty service you must first call our Consumer Return Hotline number at (718) 236-6948 to obtain a Return Authorization number. This R.A.# must appear on the outside of your package and on all paperwork relating to your return. When returning a product to us for warranty service it must be carefully packed and shipped prepaid to: R.A.# Pyle Service Center 1600 63rd Street Brooklyn, NY 11204 h i g h p e r fo r m a n c e c a r a u d i o a m p l i fi e r blue wave blue wave user's manual PLA485 PLA785 PLA885 PLA1085 PLA1285 PLA1585 limited warranty policy amplifiers You must also include the following items: · A copy of your sales receipt or other proof of purchase · A brief letter indicating the problem you are experiencing · include in your letter your return address, daytime phone number, and R.A. number · also include a check or money order for $12.00 for return shipping, handling, and insurance, or provide your Visa/MC number with expiration date. Our obligation under this warranty is limited to the repair or replacement of the defective unit when it is returned to us prepaid. This warranty will be considered void if the unit was tampered with, improperly serviced, or subject to misuse, neglect, or accidental damage. www.pyleaudio.com blue wave congratulations... the modern car audio enthusiast demands. the right choice with a Pyle Blue Wave amplifier. on your purchase of a Pyle Blue Wave Series amplifier. This amplifier extends the Pyle tradition into a totally new series of amps, designed from the ground up to deliver the power, performance and flexibility When you check the list of features offered by the PLA485, PLA785, PLA885, PLA1085, PLA1285, and PLA1585, you'll know you made blue wave table of contents general features 2-3 PLA485 PLA785 PLA1285 PLA885/1085 features and specifications electrical connections features and specifications PLA885/1085 PLA1585 PLA1585 mono input connections 20 21 22 23 24 25 26 27-28 29-30 31 32 33 4-5 6-7 8-9 10-11 12-13 14 15 16 17 18 19 high level mono input connections PLA885/1085 5 channel input connections high level input connections mono input connections PLA1585 PLA485/785/1285 PLA885/1085/1585 PLA1585 high level mono input connections PLA1585 PLA485/785/1285 PLA485/785/1285 2/4 channel input connections mono input connections stereo input connections PLA485/785/1285 speaker connections speaker connections speaker connections PLA885/1085 PLA1585 mounting and installation protection circuitry and troubleshooting precautions PLA885/1085 high level input connections PLA885/1085 PLA485 · 300 Watts x 2 Output · 600 Watts x 1 Bridged Output blue wave general features High Performance 600 Watt 2 Channel Bridgeable MOSFET Amplifier PLA785 High Performance 800 Watt 2 Channel Bridgeable MOSFET Amplifier PLA1285 High Performance 1400 Watt 2 Channel Bridgeable MOSFET Amplifier · 400 Watts x 2 Output · 800 Watts x 1 Bridged Output · Variable Hi/Lo Electronic Crossover Network · Variable Bass Boost (0 - +18 dB @ 60Hz) · Variable Input Level (Gain) Control · Remote Turn On/Off · Gold Plated RCA Inputs · High Level MOLEX Input · Power ON LED Indicator · LED Protection Indicator · S/N Ratio: > 95 dB · THD: <0.04% · Thermal Protection · Overload Protection · Short Circuit Protection · Anti-Thump Turn-On · 700 Watts x 2 Output · 1400 Watts x 1 Bridged Output · Variable Hi/Lo Electronic Crossover Network · Variable Bass Boost (0 - +18 dB @ 60Hz) · Variable Input Level (Gain) Control · Remote Turn On/Off · Gold Plated RCA Inputs · High Level MOLEX Input · Power ON LED Indicator · LED Protection Indicator · S/N Ratio: > 95 dB · THD: <0.04% · Thermal Protection · Overload Protection · Short Circuit Protection · Anti-Thump Turn-On · Variable Hi/Lo Electronic Crossover Network · Variable Bass Boost (0 - +18 dB @ 60Hz) · Variable Input Level (Gain) Control · Remote Turn On/Off · Gold Plated RCA Inputs · High Level MOLEX Input · Power ON LED Indicator · LED Protection Indicator · S/N Ratio: > 95 dB · THD: <0.04% · Thermal Protection · Overload Protection · Short Circuit Protection · Anti-Thump Turn-On 2 PLA885 · 250 Watts x 4 Output blue wave PLA1085 High Performance 1400 Watt 4 Channel Bridgeable MOSFET Amplifier High Performance 1000 Watt 4 Channel Bridgeable MOSFET Amplifier PLA1585 High Performance 1400 Watt 5 Channel Bridgeable MOSFET Amplifier · 350 Watts x 4 Output · 250 Watts x 4 Output.+ 400 Watts x 1 Output · 500 W x 2 Bridged Output ( 250 W x 2 + 500 W x 1) · Dual Variable Hi/Lo Electronic Crossover Network · Dual Variable Bass Boost (0 - +18 dB @ 60Hz) · Variable Input Level (Gain) Control · Remote Turn On/Off · Gold Plated RCA Inputs · High Level MOLEX Inputs · Power ON LED Indicator · LED Protection Indicator · S/N Ratio: > 95 dB · THD: <0.04% · Thermal Protection · Overload Protection · Short Circuit Protection · Anti-Thump Turn-On · Tri-Mode Configurable · 500W x 2 Bridged Output (250W x 2 + 500W x 1) · 700W x 2 Bridged Output (350W x 2 + 700W x 1) · Dual Variable Hi/Lo Electronic Crossover Network · Dual Variable Hi/Lo Electronic Crossover Network · Dual Variable Bass Boost (0 - +18 dB @ 60Hz) · Variable Input Level (Gain) Control · Remote Turn On/Off · Gold Plated RCA Inputs · High Level MOLEX Inputs · Power ON LED Indicator · LED Protection Indicator · S/N Ratio: > 95 dB · THD: <0.04% · Thermal Protection · Overload Protection · Short Circuit Protection · Anti-Thump Turn-On · Tri-Mode Configurable · Dual Variable Bass Boost (0 - +18 dB @ 60Hz) · Variable Input Level (Gain) Control · Remote Turn On/Off · Gold Plated RCA Inputs · High Level MOLEX Inputs · Power ON LED Indicator · LED Protection Indicator · S/N Ratio: > 95 dB · THD: <0.04% · Thermal Protection · Overload Protection · Short Circuit Protection · Anti-Thump Turn-On · Tri-Mode Configurable 3 blue wave features and controls 2 ch amp PLA485 input level control pla485 crossover mode selector bass boost level high pass frequency control low pass frequency control 4 protection LED high level inputs low level inputs power LED speaker connections power terminals power fuse crossover mode selector when used with normal, full range systems, set this switch to "FULL." If you wish to use the internal crossover to power a driver of specific frequency range, use the "LOWPASS" or "HIGHPASS" settings. input level control use this control to match the outputs of your head unit to the amplifier. Starting with your head unit set at about the 2 o'clock position, increase the amp level control until distortion begins to occur, and reduce slightly from this point. low pass frequency control when the crossover selector switch is in "low pass" mode, this control sets the upper frequency limit for audio program sent to the speakers. high pass frequency control when the crossover selector switch is in "high pass" mode, this control sets the lower frequency limit for audio program sent to the speakers. bass boost level control this control permits adjustment of the bass level up to an increase of approximately 18 dB. low level inputs this amp features gold-plated RCA input jacks for high impedance input. Use these with car stereo output which uses RCA-type connector cables. high level inputs if your car stereo lacks RCA-type output jacks, you may connect speaker output leads to these input connectors. power LED this indicator is illuminated when power is applied. protection LED this indicator is illuminated when built-in protection circuitry is activated. power fuse the fuse protects the amplifier and your car's electrical system from short circuit conditions. power terminals use these connectors to deliver power, ground and remote turn-on control to the amplifier. speaker connections these terminals are 14K gold plated to guarantee high conductivity and minimum signal loss. blue wave 2 ch amp PLA485 features and specifications PLA485 2 channel amplifier output power @ 14.4v DC, 1KHz RMS Power @ 4 Ohms RMS Power @ 2 Ohms Maximum Power Output frequency response input impedance low level inputs high level inputs 50 Watts x 2 80 Watts x 2 300 Watts x 2 15 Hz-30 KHz 10K Ohms 100 Ohms 250mV 2.5V 14.4V DC Neg. Ground (10.5-16V) 2-4 Ohms 4-8 Ohms 15A 300 x 62 x 209 11.8 x 2.4 x 8.2 input sensitivity low level inputs high level inputs power supply voltage matching speaker impedance stereo mode bridged mode maximum current draw dimensions (W x H x L) mm inches 5 blue wave features and controls 2 ch amp PLA785 input level control pla785 crossover mode selector bass boost level high pass frequency control low pass frequency control 6 protection LED high level inputs low level inputs power LED speaker connections power terminals power fuse crossover mode selector when used with normal, full range systems, set this switch to "FULL." If you wish to use the internal crossover to power a driver of specific frequency range, use the "LOWPASS" or "HIGHPASS" settings. input level control use this control to match the outputs of your head unit to the amplifier. Starting with your head unit set at about the 2 o'clock position, increase the amp level control until distortion begins to occur, and reduce slightly from this point. low pass frequency control when the crossover selector switch is in "low pass" mode, this control sets the upper frequency limit for audio program sent to the speakers. high pass frequency control when the crossover selector switch is in "high pass" mode, this control sets the lower frequency limit for audio program sent to the speakers. bass boost level control this control permits adjustment of the bass level up to an increase of approximately 18 dB. low level inputs this amp features gold-plated RCA input jacks for high impedance input. Use these with car stereo output which uses RCA-type connector cables. high level inputs if your car stereo lacks RCA-type output jacks, you may connect speaker output leads to these input connectors. power LED this indicator is illuminated when power is applied. protection LED this indicator is illuminated when built-in protection circuitry is activated. power fuse the fuse protects the amplifier and your car's electrical system from short circuit conditions. power terminals use these connectors to deliver power, ground and remote turn-on control to the amplifier. speaker connections these terminals are 14K gold plated to guarantee high conductivity and minimum signal loss. blue wave 2 ch amp PLA785 features and specifications PLA785 2 channel amplifier output power @ 14.4v DC, 1KHz RMS Power @ 4 Ohms RMS Power @ 2 Ohms Maximum Power Output frequency response input impedance low level inputs high level inputs 85 Watts x 2 125 Watts x 2 400 Watts x 2 15 Hz-30 KHz 10K Ohms 100 Ohms 250mV 2.5V 14.4V DC Neg. Ground (10.5-16V) 2-4 Ohms 4-8 Ohms 20A 300 x 62 x 281 11.8 x 2.4 x 11 input sensitivity low level inputs high level inputs power supply voltage matching speaker impedance stereo mode bridged mode maximum current draw dimensions (W x H x L) mm inches 7 blue wave features and controls 2 ch amp PLA1285 input level control pla1285 crossover mode selector bass boost level high pass frequency control low pass frequency control 8 protection LED high level inputs low level inputs power LED speaker connections power terminals power fuse crossover mode selector when used with normal, full range systems, set this switch to "FULL." If you wish to use the internal crossover to power a driver of specific frequency range, use the "LOWPASS" or "HIGHPASS" settings. input level control use this control to match the outputs of your head unit to the amplifier. Starting with your head unit set at about the 2 o'clock position, increase the amp level control until distortion begins to occur, and reduce slightly from this point. low pass frequency control when the crossover selector switch is in "low pass" mode, this control sets the upper frequency limit for audio program sent to the speakers. high pass frequency control when the crossover selector switch is in "high pass" mode, this control sets the lower frequency limit for audi ...