User manual PYLE PLTV7R

MOTORIZED 7 IN -DASH COLOR LCD MONITOR WITH AM/FM STEREO RADIO MODEL: PLTV7R OWNER MANUAL Any changes or modifications in construction of this device which is not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment. ! WARNING The exclamation point within an equilateral triangle and WARNING are intended to alert the user to the presence of important operating instructions. Failure to heed the instruction will result in severe injury or death. DO NOT WATCH VIDEO WHILE DRIVING Watching the video may distract the driver from looking ahead of the vehicle and cause an accident. DO NOT OPERATE ANY FUNCTION THAT TAKES YOUR ATTENTION AWAY FROM SAFELY DRIVING YOUR VEHICLE Any function that requires your prolonged attention should only be performed after coming to a complete stop. Always stop the vehicle in a safe location before performing these functions. Failure to do so may result in an accident. DO NOT DISASSEMBLE OR ALTER Attempts to disassemble or alter may lead to an accident, fire and / or electric shock. KEEP SMALL ARTICLES OUT OF THE REACH OF CHILDREN Store small articles (screws etc.) in places not accessible to children. If swallowed, consult a physician immediately. USE THE CORRECT AMPERE RATING WHEN REPLACING FUSES Replace fuses only with fuses of the same ampere rating. Failure to do so may result in a fire and / or damage to the vehicle. HALT USE IMMEDIATELY IF A PROBLEM APPEARS When problems appear, stop using the system immediately and contact the dealer from whom you purchased the equipment. 1 ! CAUTION The exclamation point within an equilateral triangle and CAUTION are intended to alert the user to the presence of important operating instructions. Failure to heed the instructions can result in injury or material damage. DO NOT RAISE THE VOLUME EXCESSIVELY Keep the volume at a level, where you can still hear outside noises while driving . Driving while unable to hear outside could cause an accident. DO NOT USE THIS EQUIPMENT OUTSIDE THE VEHICLE Do not use this equipment for purposes other than those listed for a vehicle. Failure to do so may result in an electric shock or an injury. KEEP FOREIGN OBJECTS OUT OF THE MONITOR COMPARTMENT Keep foreign objects out of the monitor compartment. Also, avoid placing your hands in the area where it might interfere with the monitor's operation. STOP THE VEHICLE BEFORE CARRYING OUT ANY OPERATION THAT COULD INTERFERES WITH YOUR DRIVING. If the operation of this unit (such as raising or lowering of the monitor, etc.) interferes with you driving, stop the vehicle in a safe location before attempting operation. DO NOT MIX NEW BATTERIES WITH OLD BATTERIES. INSERT WITH THE CORRECT BATTERY POLARITY Do not mix new batteries with old batteries and do not replace with other than specified batteries. When inserting the batteries, be sure to observe proper polarity (+ and - ) as instructed. Battery rupture or chemical leakage can cause an injury or equipment malfunction. 2 ! CAUTION The exclamation point within an equilateral triangle and CAUTION are intended to alert the user to the presence of important operating instructions. Failure to heed the instructions can result in injury or material damage. Operation of some of the functions of this unit is very complex. Because of this, it was deemed necessary to place these functions into a special SETUP screen. this will restrict operation of these functions to times when the vehicle is parked. This ensures the focus of the driver's attention will be on the road and not on the unit. This has been done for the safety of the driver and passengers. TEMPERATURE Be sure the temperature inside the vehicle is between +60 C (+140 F) and -5 C (+23 F) before turning your unit on. FUSE REPLACEMENT When replacing the fuses, the replacement must be the same amperage as shown on the fuse holder. If the fuse(s) blow more then once, carefully check all electrical connections for shorted circuitry. Also have your vehicle s voltage regulator checked. MAINTENANCE If you have problems, do not attempt to repair the unit yourself. Return it to your purchasing dealer. INSTALLATION LOCATION Make sure the unit will not be exposed to : Direct sun & heat High humidity Excessive dust Excessive vibrations 3 INTRODUCTION MONITOR AV IN POWER ON/OFF BUTTON MODE SELECTION BUTTON AS/ATM BUTTON SOUND MUTE BUTTON VOLUME UP/DOWN BUTTON SEARCH UP/DOWN BUTTON OPEN/CLOSE BUTTON TILT BUTTON BAND SELECTION BUTTON MENU SELECTION BUTTON 4 REMOTE CONTROLLER POWER ON/OFF BUTTON POWER SEA RC MODE SELECTION BUTTON AS/ATM BUTTON H VOL MENU VOL S SOUND MUTE BUTTON EA PA U RC H SE MODE MUTE VOLUME UP/DOWN BUTTON SEARCH UP/DOWN BUTTON AS/ATM CH NAVI CH OPEN/CLOSE BUTTON MANUAL MEMORY BUTTON CHANNEL UP/DOWN BUTTON NAVIGATION BUTTON 1 4 2 3 6 5 7 8 0 9 A M ASPECT BUTTON MENU SELECTION BUTTON 5 REMOTE CONTROL UNIT Replacing battery Applicable battery : Use two AAA sized dry batteries. 1. Opening the battery cover. Push and slide the cover in the arrow direction, and the cover will be removed. 2.Replacing the battery. Remove the old batteries. Insert new ones matching the (+) and (-) polarities as shown in the diagram inside the unit. 3. Closing the cover. Push the cover in the arrow direction until a click is heard. 6 BASIC OPERATION POWER ON / OFF 1.POWER ON 1) Press the POWER button to turn the power on. But the monitor will not open. 2) You can also turn the power on by pressing the OPEN/CLOSE button. The power will be on and the monitor will open. 2. POWER OFF 1) Press the POWER button again to turn the power off. 2) If you turn the power off by presing the POWER button when the monitor opens, the monitor will not close. If the car key is pulled out, or the OPEN/CLOSE button is pressed the monitor will automatically close. OPENING THE MONITOR Press OPEN/CLOSE button. The monitor will open. NOTE If the OPEN/CLOSE button is pressed when the monitor is closed, the monitor will open and the power will turn on. 7 CLOSING THE MONITOR AV IN 1. Hold left and right upper side of the monitor and set the left and right angle of the monitor parallel with the front of the unit as the picture. 2. Press OPEN/CLOSE button. The monitor will close. NOTE 1.If the left and right angle of the monitor is not parallel to the the front of the unit, the monitor can not be closed. 2. If the OPEN/CLOSE button is pressed while radio or video is on, the monitor will close. But the sound is still on. Press the POWER button to turn the sound off. ADJUSTING THE TILT POSITION 1.Press the MENU button three times on radio mode or twice on AV mode to select the USER SELECTOR menu 2.Press the SEARCH UP/DOWN button to select TILT. 3.Press the VOLUME > or < button. Each time you press the VOLUME > or < button, the monitor will slant forward or backward one step. The TILT position can be adjusted in 5 steps. For more information, pls see page 20 of owner s manual. NOTE You can also adjust the TILT position by pushing the TILT UP/DOWN button on the unit. Each time you press the TILT UP button, the monitor slants forward one step. Each time you press the TILT DOWN button, the monitor slants backward one step. The tilt can be adjusted in 5 steps. 8 ADJUSTING THE SLIDE POSITION 1.Press the MENU button three times on radio mode or twice on AV mode to select the USER SELECTOR menu 2.Press the SEARCH UP/DOWN button to select MOVE 3.Press the VOLUME > button to select FORWARD. The monitor will slide one step (15mm) to the front. 4.Press the VOLUME < button to select BACKWARD. The monitor will slide one step (15mm) to the back. For more information, pls see page 20 of owner s manual. NOTE 1.If the VOLUME > button is pressed when FORWARD is selected, the monitor will not slide to the front. 2.If the VOLUME < button is pressed when BACKWARD is selected, the monitor will not slide to the back. ADJUSTING THE LEFT/RIGHT VIEWING POSITION The monitor s left/right position can be adjusted for easier viewing by hand-operating. AV IN 9 SELECTING MODE Press the MODE button to select the desired mode. Each time you press the button, the mode changes as follows. RADIO -> AV1 -> AV2 -> AV3 (CD OR VCD CHANGER) -> AV4 (TV) -> RADIO NOTE 1.The CD or VCD changer must be connected to AV3. 2.The TV tuner box must be connected to AV4. ADJUSTING VOLUME Press the VOLUME < or > button to adjust the volume level. AUDIO MUTE Press the MUTE button to make the sound quite. Press the MUTE button again to return to the previous audio level. RESET 1. If the unit does not seem to be working right, press the RESET switch with a pencil or other pointed object. The RESET switch is mounted behind the small hole on the upper right of the front face, to the left of the AUDIO INPUT hole. 2. If the RESET switch is pressed, the power will be off, press the POWER button to turn power on. 3. If reset does not solve the problem, consult your installer. 10 ADJUSTING THE TV/VIDEO PICTURE MODE (ASPECT) Each time you press A (ASPECT) button, the picture mode switches between Normal, Full, Zoom and Wide. NORMAL MODE The monitor displays normal picture at the center of the screen with the proportion of 4 to 3. The screen shows a vertical black belt at each side. FULL MODE The monitor displays normal picture wider by stretching out horizontally with the proportion of 16 to 9. ZOOM MODE The monitor displays normal picture wider by stretching out horizontally and vertically with the proportion of 4 to 3. The screen doesn t show upper and down part of the picture slightly. WIDE MODE The monitor displays normal picture wider by unevenly stretching out horizontally with the proportion of 16 to 9. The stretching proportion is bigger toward each side of the picture. 11 RADIO CONTROL Press the OPEN/CLOSE button to turn the power on and to open the monitor. The monitor shows following picture. (Radio mode) MANUAL TUNING Press the CH UP/DOWN button to move downward or upward one step respectively until the desired station frequency is selected. MANUAL STORING OF STATION 1. Tune in the desired radio station you wish to store on the CH number. 2. Press the M(MEMORY) button to store the desired radio station. The station will be stored into the next CH number of the last CH number previously stored station. 3. They can be stored up to 30 radio stations in each band. FM1:30, FM2: 30, AM1:30, AM2:30 stations (total 120 stations). AUTO MEMORY OF STATION 1. Tune in desired radio station you wish to store on the CH number. 2. Press the AS/ATM button for at least 2 seconds. The frequency on the display continues to change while the auto memory is in progress. The tuner will automatically seek and can store up to 30 stations in each band in order of frequency signal.They can be stored in FM1: 30, FM2: 30, AM1: 30 and AM2: 30 stations (total 120 stations). 3. When the auto memory has been completed, the tuner goes to the station stored in the CH No.1. 12 NOTE On CD changer mode, you can pause or playback the current CD by pushing the AS/ATM button. TUNING TO THE STORED STATION Press the SEARCH UP/DOWN button repeatedly until the desired band is selected. SELECTING THE BAND AREA FOR YOUR COUNTRY 1. Press the MENU button on radio mode. The monitor shows following picture. 2. Press the SEARCH UP/DOWN button to select RADIO BAND. 3. When RADIO BAND is selected, press CH UP/DOWN button to select the radio band area (EUROPE or USA) for your country. Each time you press the CH UP/DOWN button, the band switches as EUROPE --> USA --> EUROPE. RADIO BAND 1. Press the SEARCH UP/DOWN button to select RADIO BAND. 2. When RADIO BAND is selected, press the VOLUME < or > button to select the band. Each time you press the VOLUME < or > button, the band switches as FM1 -> FM2 -> AM1 -> AM2 -> FM1 3. You can also select the band by pushing the BAND button on the unit. Each time you press the BAND button, the band switches as FM1 -> FM2 ->AM1 -> AM2 -> FM1. 13 TREBLE 1. Press the SEARCH UP/DOWN button to select TREBLE. 2. Press the VOLUME < or > button to adjust treble level. BASS 1. Press the SEARCH UP/DOWN button to select BASS. 2. Press the VOLUME < or > button to adjust bass level. SUB WOOFER 1. Press the SEARCH UP/DOWN button to select SUB WOOFER. 2. Press the VOLUME < or > button to adjust sub woofer level. LOUDNESS 1. Press the SEARCH UP/DOWN button to select LOUD. 2. Press the VOLUME < or > button to adjust loudness level. 14 NAVIGATION SETTING THE NAVIGATION 1. Connect a NAVIGATION system to AV1 or AV2 Input terminals on the rear of the unit. 2. Press the MODE button to select radio mode. 3. Press the MENU button to select following picture. 4. Press the SEARCH UP/DOWN button to select NAVIGATION. 5. Press the VOLUME < or > button to select AV1 or AV2 connected to the NAVIGATION system. Each time you press this button, AV Input changes as AV 1 -> AV2 -> OFF -> AV1. WATCHING THE NAVIGATION PICTURE Press the NAVI button on radio or AV1, 2 or 3 mode. The monitor shows the navigation picture. NOTE Do not select the AV mode connected to the NAVIGATION system with the MODE button. If AV Input connected to the NAVIGATION system is selected with the MODE button, the monitor does not show the NAVIGATION picture. The monitor shows the WARNING picture. 15 CAMERA IN SETTING THE CAMERA IN 1. Connect a Back View Camera to AV1,2 or 3 Input terminals on the rear of the unit. * When the VCD changer is connected to AV3 Video input, The back view camera can be connected only to AV1 or AV2 video input. 2. Press the MODE button to select radio mode. 3. Press the MENU button to select following picture. 4. Press the SEARCH UP/DOWN button to select CAMERA IN. 5. Press the VOLUME < or > button to select AV1,2 or 3 that Back View Camera is connected. Each time you press this button, AV Input changes as AV1 -> AV2 -> AV3 -> OFF -> AV1. WATCHING THE BACK VIEW PICTURE Set the rear gear on any mode. The monitor shows the back view camera picture. NOTE If AV Input connected to the Back View Camera is selected with the MODE button, the monitor does not show the back view camera picture. The monitor shows the WARNING picture. 16 CD CHANGER CONTROL When a CD (VCD) changer is connected to AV3 of this unit, AV3 mode changes to CDC mode and CDC control menu is displayed on the screen. 1. Press the MODE button to select CD CHANGER (AV3) mode. Each time you press this button, the display changes as follows. RADIO-> AV1-> AV2-> AV3 (CD or VCD CHANGER) -> AV4(TV) -> RADIO. 2. When CD CHANGER (AV3) mode is selected, The monitor shows following picture. 3. Press the SEARCH UP/DOWN button to select the item. 4. Press the CH UP/DOWN button to adjust the level of the selected item. You can also adjust the level upward by pushing the BAND button on the unit. CD STATUS This shows the current CD status (DISC CHECK, SEEK, PLAY, ETC) PLAY TIME This shows playing time of the disc being played. 17 INTRO SCAN 1. Press the SEARCH button to select INTRO SCAN. 2. Press the CH UP/DOWN button to select the item. Each time you press the CH UP/DOWN button or the BAND button, the item changes as ONE -> ALL -> OFF -> ONE. ALL: The first 10 seconds of first track of all the discs will be played in succession. ONE: The first 10 seconds of each track of the selected disc will be played in succession. OFF: INTRO SCAN will be off. REPEAT 1. Press the SEARCH button to select REPEAT. 2. Press the CH UP/DOWN button or the band button to select the item. Each time you press the CH button, the item changes as ONE -> ALL -> OFF -> ONE. ALL: All the tracks on the current disc will be played repeatedly. ONE: The selected track on the current disc will be played repeatedly. OFF: REPEAT will be off. RANDOM 1. Press the SEARCH UP/DOWN button to select RANDOM . 2. Press the CH UP/DOWN button or the BAND button to select the item. Each time you press the button, the item changes as ONE -> ALL -> OFF -> ONE. ALL: The tracks on all the discs in the CD/VCD changer will be played in random order. ONE: All the tracks on the current disc will be played in random order. OFF: RANDOM will be off. PAUSE Press the AS/ATM button to pause playback. Press the button again to resume playback. NOTE It is recommended for the stable CD changer control to execute the next function at least 0.5 seconds later from the current function. 18 VOLUME ADJUSTMENT OF EACH CHANNEL You can adjust the volume level of each channel of the radio or AV sources. ADJUSTING THE VOLUME OF EACH CHANNEL OF RADIO 1.Press the MENU button twice on radio mode. But to adjust volume level of each channel of AV sources, press the MENU button once on AV mode. The monitor shows following picture. 2. Press the SEARCH UP/DOWN button to select the audio channel that you want to adjust. 3. Press the VOLUME < or > button to adjust the volume level of the selected audio channel. DEFAULT 1. Press the SEARCH UP/DOWN button to select DEFAULT. 2. Press the VOLUME < or > button to select ON or OFF. Each time you press the VOLUME < or > button, the display changes as ON -> OFF -> ON. 19 FINE ADJUSTMENT FOR CENTER FREQUENCY AND TILT/SLIDE POSITION 1. Press the MENU button when the monitor shows following picture. The monitor shows following picture. USER SELECTOR TILT POSITON MOVE 0 FORWARD 2. Press the SEARCH UP/DOWN button to select the items that you want to adjust. 3. Press the VOLUME < or > button to adjust the level of the selected item. 20 SCREEN CONTROL 1. Press the MENU button when the monitor shows following picture. USER SELECTOR TILT POSITON MOVE 0 FORWARD The monitor shows following picture. 2. Press the SEARCH UP/DOWN button to select the items that you want to adjust. 3. Press the VOLUME < or > button to adjust the level of the selected item. 21 SELECTING COLOR/SOUND SYSTEM 1. Press the SEARCH UP/DOWN button to select COLOR SYSTEM for the video source on SCREEN CONTROL menu. 2. Press the VOLUME < or > button to select PAL or NTSC for the video source. NOTE To select the color system for the TV When the TV tuner box is connected to the AV4 of monitor unit, 1. Select color system (PAL or NTSC) at COLOR SYSTEM on SCREEN CONTROL menu on radio mode first. 2.Select color and sound system again at COLOR SYSTEM on FUNCTION menu on TV mode. For more information, see page 5&6 "COLOR&SOUND SYSTEM in owner's manual for the TV tuner. NOTE If the monitor displays the picture in black & white color, select the color system again for the video source. 22 VOLUME CONTROL ON AV MODE To adjust audio level of AV sources on AV mode, 1. Press the VOULME < or > button. The monitor shows following picture. 2. Press the SEARCH UP/DOWN button to select the items that you want to adjust. 3. Press the VOLUME < or > button to adjust the audio level of the selected item. 23 WARNING SCREEN The monitor shows following warning picture when the parking brake is not set or when driving to prevent traffic accident that may be caused while watching the screen. The monitor shows the warning picture only and does not show any other pictures, but you can enjoy the sound only by adjusting the volume. 24 INSTALLATION PRECAUTIONS Choose the mounting location carefully so that the unit will not interfere with the normal driving functions of the driver. Avoid installing the unit where it would be subject to high temperatures, such as from direct sunlight or hot air from the heater, or where it would be subject to dust, dirt or excessive vibration. Use only the supplied mounting hardware for a safe and secure installation. Be sure to remove the front panel before installing the unit. Mounting angle adjustment Adjust the mounting angle to less than 20 . MOUNTING EXAMPLE Installation in the dashboard Convenient spot on the fire wall Strap Be sure to use the strap to secure the back of the unit in place to prevent sound cuts or skips. The strap can be bent by hand to the desired angle. Metal Mounting Strap Tapping Screw Holder After inserting the holder into the dashboard, select the appropriate tabs according to the thickness of the dashboard material and bend them inwards to secure the holder in place. 3 A How to Detach the Mounting Frame 1. Insert release keys into the slots A. 2. Remove the frame B from the unit. Keep the release key in the safe place as you may need it in the future to remove the unit from the car. 2 B 2 NOTE : Keep the release keys in the safe place as you may need if in the future to move the unit from the car. 25 BASIC CONNECTIONS (Brown) (Yellow) (Blue) (Red) (Orange) REMOTE TURN-ON To amplifier or equalizer POWER ANT To power antenna PARKING BRAKE To the parking brake signal lead INGITION BATTERY Ignition Key (Black) GND - + Battery SPEAKER RIGHT FRONT (Gray) + (Gray/Black) (Green/Black) Front right Rear right SPEAKER RIGHT REAR (Green) (Violet) + + Rear left SPEAKER LEFT REAR Speakers (Violet/Black) (White/Black) SPEAKER LEFT FRONT (White) + NOTE 1. Be sure that the PARKING SENSOR WIRE must be grounded or opened. If it is connected to ACC (B+). The unit can be damaged. 2. Do not ground the POWER ANTENNA wire. If it is grounded, the unit can be damaged. 26 Front left 16P Connector 8P Din CD (VCD) Changer V 3 INPUT Video out (Yellow) Video in (Yellow) AV2 INPUT 8PIN DIN ANT. PRE AMP RCA LINE OUT TV Tuner Box Front Right BATT(YELLOW) ACC(RED) GND(BLACK) Red Right Left Black Black 4PIN DIN Front Left White Red White Ext. AV 2 Rear Right RADIO MONITOR INPUT(RCA Cable) Red Rear Left White Video Yellow Sub Woofer Yellow VIDEO out VIDEO in Yellow Red White Yellow AV-1 INPUT Red Right AV4 Input TV Tuner Input Right Left Video White Left Yellow Video Ext. Monitor Ext. AV 1 CONNECTING TO CD CHANGER AND TV TUNER BOX 27 AV INPUT FACE PLATE OF THE UNIT NOTE 3.5 AV input on the front face of the unit is same input with AV1 input on the rear of the unit. If the sources are connected both input terminals,the 3.5 input has priority in working. 28 SPECIFICATIONS AM SECTION USA BAND Frequency Range Frequency Step EUROPE BAND Frequency Range Frequency Step Intermediate Frequency Usable Sensitivity Image Rejection Ratio IF Rejection Ratio FM SECTION Frequency Range Frequency Step Manual tuning Seek tuning Intermediate Frequency Usable Sensitivity Image Rejection Ratio If Rejection Ratio CD CHANGER Signal/Noise radio Frequency response Channel separation D/A converter 530-1710KHz 10KHz 522-1620KHz 9KHz 450 KHz 32 dB 45dB 100dB 87.5~108 MHz 50 KHz 100KHz 10.7MHz 12dB 45dB 6odB >80dB 20kHz - 20kHz >60dB 16Bit/CH AMPLIFIER Total MAX power Power output 200 Watts peak 50W X 4 GENERAL Power Supply Polarity Speaker Impedance Fuses DIMENSIONS WEIGHT Net Gross . C 14.4V (11V - 15V) D Negative Ground only 4~8 Fast blow (1A and 10A) 178(W)x 50(H)x 155(D)mm 2.5Kg 3.5Kg 29