PLTVR5 OWNER'S MANUAL COLOR LCD TV/RECEIVER WITH CD CHANGER CONTROL INSTALLATION Notes: · Choose the mounting location where the unit will not interfere with the normal driving function of the driver. · Before finally installing the unit, connect the wiring temporarily and make sure it is all connected up properly and the unit and the system work properly. · Use only the parts included with the unit to ensure proper installation. The use of unauthorized parts can cause malfunctions. · Consult with your nearest dealer if installation requires the drilling of holes or other modifications of the vehicle. · Install the unit where it does not get in the driver's way and cannot injure the passenger if there is a sudden stop, like an emergency stop. · If installation angle exceeds 30° from horizontal, the unit might not give its optimum performance. 30° · Avoid installing the unit where it would be subject to high temperature, such as from direct sunlight, or from hot air, from the heater, or where it would be subject to dust, dirt or excessive vibration. INSTALLATION HARDWARE Bracket (A) (2 pcs) Bracket (B) (2 pcs) Double sided tape (2 pcs) Lever (2 pcs) Hexagonal Bolt (M6 x 12) (4 pcs) Tapping Screw (M5 x 12) (4 pcs) Mounting Bolt (M5 x 5) (8 pcs) Mounting Bolt (M4 x 5) (4 pcs) Strap (1 pcs) Tapping Screw (M5 x 25) (1 pcs) Nut (M5) (1 pcs) Plain Washer (M5) (1 pcs) Spring Washer (M5) (5 pcs) Spring Washer (M6) (4 pcs) 2 MOUNTING THE TUNER UNIT 4 6 6 5 7 1 1 3 8 5 7 3 2 8 6 5 7 4 2 Step 1 Step 2 1. 2. 3. 4. Bracket (A) Mounting Bolt (M5 x 5) Bracket (B) Hexagonal Bolt with Washer (M6 x 12) 5. 6. 7. 8. Tapping Screw with Washer (M5 x 12) Spring Washer (M6) Spring Washer (M5) Double Sided Tape INSTALL THE DISPLAY UNIT Before install the display unit, please remove its tail screw and cable parts. This unit can be properly installed either from "front" (convertional DIN Front-mount) or "rear" (DIN Rear-mount installation, utilizing threaded screw holes at the sides of the unit chassis). For details, refer to the following illustrated installation methods. DIN FRONT-MOUNT Installing the unit 1 2 182 1. Dashboard 2. Holder After inserting the holder into the dashboard, select the appropriate tab according to the thickness of the dashboard material and bend them inwards to secure the holder in place. 3. Display Unit 53 3 (Fig. 1) 3 1. Dashboard 1 6 4 2 3 7 5 2. Nut (M5) 3. Spring Washer 4. Tapping Screw with Washer (M5 x 25) 5. Screw 6. Plain Washer 7. Strap Be sure to use the strap to secure the back of the unit in place. The strap can be bent by hand to the desired angle. (Fig. 2) Removing the unit 1 1. Lever Insert the levers supplied with the unit into the grooves at both sides of the unit as shown in figure until they click. Pulling the levers upward and out to makes it possible to remove the unit. DIN REAR-MOUNT Installation using the screw holes on the both sides of the unit. 1 Fastening the unit to the factory radio mounting bracket. 1. Select a position where the screw holes of the bracket and the screw holes of the main unit become aligned (are fitted), and tighten the screws at 2 places on each side. Use either truss screws (5 x 5mm) or screws (4 x 5mm), depending on the shape of the screw holes in the bracket. 2. Screw 3. Factory Radio Mounting Bracket 4. Dashboard or Console 5. Hook and Screw (Remove this part) Note: The frame, strap, and half-sleeve are not used for REAR-MOUNT. 2 5 4 2 3 5 4 HOW TO OPEN AND CLOSE THE SCREEN DISPLAY 1. Press release button to draw out the screen display. Release Button 2. Turning the display upward. 3. Adjusting the viewing angle. Angle should be adjusted slowly without applying unreasonable force. 5 4. Turning the display downward. Make sure to return the display to centre position before drawing in. It cannot be draw in with its angles adjusted. 5. Push the panel, the display will be drawn in. 6 ELECTRICAL CONNECTION RADIO/TV MAIN UNIT (VIEW FROM REAR) TV DIVERSITY ANTENNA INPUT RADIO/TV MAIN UNIT (VIEW FROM FRONT) AV INPUT AV1 TV MONITOR RADIO CONTROL CDC INPUT AV2 VIDEO AUDIO­R AUDIO­L (FOR RCA LINE VERSION ONLY) FRONT RCA CABLE BLACK PLUG RADIO ANTENNA INPUT REAR RCA CABLE TV CONTROL TV DIVERSITY ANTENNA INPUT FROM VIDEO/AUDIO SOURCE 75ohm RF WIRE (BLACK) GREY/BLACK CHOKE BOX VIDEO OUTPUT TO CD CHANGER Rch RED BLUE/WHITE POWANT YELLOW MEMORY BLACK GROUND RED ACC Lch WHITE Lch WHITE Rch RED DISPLAY UNIT TO POWER SUPPLY RADIO CONTROL TV MONITOR GREEN/BLACK VIOLET/BLACK WHITE/BLACK GREY/BLACK GREEN VIOLET WHITE GREY REAR Rch SPK FRONT Rch SPK CAUTION: 1. If the TV control grey cable is connected to car brake, when the car is running, you cannot switch into TV mode. 2. To select CD changer's sort: Before installing the unit, connect the CD changer with the unit correctly and turn on the power to make the unit work in CD changer state. If the operation normally, the switch button's position is right, otherwise, please dial the switch button to the other position. Note: How to select A or B in CDC SET is different according to the units and the customers use. 7 REAR Lch SPK FRONT Lch SPK BLACK/GREY CABLE (BROWN) (GREY) BLACK CABLE GREY GREY PLUG OPERATION 12 32 9 10 4 16 5 2 13 3 11 22 17 18 19 15 20 21 6 8 7 1 14 23 25 24 29 30 8 28 26 27 31 4 GENERAL OPERATION · ON/OFF Switch on the unit by pressing POWER button (1). When system is on, press it again to turn it off. · FACEPLATE RELEASE Press REL button (2) to draw out the faceplate, push the panel to draw in. When the faceplate is drawn out, turn the faceplate upward and adjust TV display. · SELECTING SOUND MODE Press SEL button (6) to move display through volume, bass, treble, balance and fader functions. Use VOLUME > (7) and VOLUME < (8) buttons to adjust the selected mode. When mode has not been adjusted for several seconds, display returns to previous display status (e.g. radio display or CDC display). VOL (Volume) BAS (Bass) TRE (Treble) BAL (Balance) FAD (Fader) Volume Adjust volume level using VOLUME > (7) and VOLUME < (8) buttons. Bass Press SEL button (6) for one time. Adjust bass level using VOLUME > (7) and VOLUME < (8) buttons. Treble Press SEL button (6) for two times. Adjust treble level using VOLUME > (7) and VOLUME < (8) buttons. Balance Press SEL button (6) for three times. Adjust sound balance between left and right speakers using VOLUME > (7) and VOLUME < (8) buttons. Fader Press SEL button (6) for four times. Adjust sound balance between front and rear speakers using VOLUME > (7) and VOLUME < (8) buttons. · SELECTING PLAYING MODE When the screen display is drawn in, press MODE button (12) to select desired playing mode between radio and CDC. When the screen display is drawn out, the unit would automatically switch into TV mode. By pressing MODE button (12), you can select desired playing mode among TV, radio and CDC. CAUTION: The unit cannot be switched into TV mode, when the car is running. So at this time, you just select playing mode between radio and CDC. · MUTE Press MUT button (3) to cut down sound output, "MUTE" will appear on the display. Press it again to resume the previous volume mode. · LOUDNESS Press LOU button (22) to increase bass output, "LOUD" will appear on the display. Press it again to release the mode. 9 · MONO/STEREO Press MON button (10) to select mono or stereo mode. In radio operation, press the button to select mono or stereo reception for radio station. You can sometime improve reception of distant stations by select mono mode. · SETTING THE CLOCK Press DSP button (5) to change the display into clock display. While the current time is appeared on the display, press it again to return to frequency showing. Time Setting - Set hours: Holding down DSP button (5) for several seconds, and the clock is blinking on the display, press button (14) to adjust the hour. - Set minutes: Holding down DSP button (5) for several seconds, and the clock is blinking on the display, press button (13) to adjust the minutes. · LIQUID CRYSTAL DISPLAY The LCD (4) can show the current state of the unit. · RESET Reset button (32) must be activated with either a ball point pen or thin metal object. Reset button (32) is to be activated for the following reasons: - Initial installation of the unit when all wiring is completed. - All the function buttons do not operate. - Error symbol on the display. 10 RADIO OPERATION · SELECTING BAND Press BAND button (11) to change between three FM bands and two AM bands. Each band stores up to six preset stations. FM1 FM2 FM3 AM1 AM2 · SELECTING STATION During radio mode, press button (13) to increase frequency or button (14) to decrease frequency by one step of channel spacing. Hold the button longer for fast tuning. The frequency is updated correspondingly on display. · LOCAL/DISTANCE Press the LOC button (9) to select between local mode for receiving with strong signals and distance mode for receiving with weak signals when tuning. · SELECTING MEMORY Press preset memory buttons (15) to preset stations at tuner mode. With this system, a total of 30 stations can be stored in the memory of six buttons. The stations might be FM1, FM2, FM3, AM1 and AM2 band. The operation is as below: - Store in Memory Press and hold desired memory location button for several seconds. The current listening station will be stored into the number button. - Retrieve a Preset Station Press any one of the buttons (15) to retrieve a station which had been stored in the memory in advance the chosen number is shown on display. · AUTO MEMORY STORING & SCANNING - Auto Memory Storing Seeks the six strongest stations in the pre-selected band automatically and stores the stations automatically in preset memories. Initially the tuner seeks and memories the stations in local mode until 6 stations are fully occupied. Otherwise, seeking is proceeded in distance mode. - Auto Memory Scanning Check the stations stored in the preset memories. Press to retrieve automatically the current stations stored in six preset memories and it will display for several seconds. Press either the AMS button (16) again or anyone of the memory buttons to stop the scan operation. During the preset scan operation, the channel number flashes on the display for several seconds. Preset station scan continuously in the pre-selected band. 11 CDC OPERATION · SELECTING TRACK During CDC mode, press button (14) or button (13) shortly to move to the previous track or the next track. The track number shows on the display. · SELECTING CD Press D.UP button (17) to select next disc and D.DN button (18) to select previous disc. · REPEAT THE SAME TRACK Press RPT button (19) to continuously repeat the same track on the current disc. Press it again to continuously repeat all tracks on the current disc. Press it the third time to stop repeating. · PREVIEW ALL TRACKS Press SCN button (20) to play the first several seconds of each track on the current disc. Press it again to stop intro and listen to track. · PLAY ALL TRACKS Press RND button (21) to play all tracks on the current CD in random order. Press it again to cancel the mode. · CD CHANGER SETTING MAIN UNIT (VIEW FROM FRONT) CDC SET A B Switch Button Reference the figure above, when the CD input use 6 disc CD changer, the switch button should be dialed to B side, when the CD input use 10 disc CD changer, the switch button should be dialed to A side. 12 TV OPERATION · SELECTING RECEIVING MODE Press TV/AV button (31) to select among TVch/AV1/AV2. · PICTURE ADJUSTMENT/PROGRAM SETTING/SYSTEM CONTROL In TV mode, press MENU button (23) to enter the main menu. And the menu includes three sub-menus: PICTURE MENU, TUNER MENU and SYSTEM MENU. Press the button repeatedly or press CHANNEL SELECT + button (28) or CHANNEL SELECT ­ button (29) to select the desired item then press CONTROL + button (24) or CONTROL ­ button (25) to enter the corresponding sub-menu to set. - In PICTURE MENU, use CHANNEL SELECT + button (28) or CHANNEL SELECT ­ button (29) to select picture mode upward or downward as follows: BRIGHT CONTRAST COLOR SHARP TINT Then use CONTROL + button (24) or CONTROL ­ button (25) to adjust the selected item. Note: In PAL SYSTEM, there is no "TINT" item. - In TUNER MENU, use CHANNEL SELECT + button (28) or CHANNEL SELECT ­ button (29) to select picture mode upward or downward as follows: POS SKIP BAND FINE AFT SEARCH ASM Then use CONTROL + button (24) or CONTROL ­ button (25) to adjust the selected item. - In SYSTEM MENU, use CHANNEL SELECT + button (28) or CHANNEL SELECT ­ button (29) to select picture mode upward or downward as follows: COLOR SOUND LANG. B/B CORING HALFTONE Then use CONTROL + button (24) or CONTROL ­ button (25) to adjust the selected item. In AV mode, press MENU button (23), the screen will display PICTURE MENU and SYSTEM MENU but not TUNER MENU. And in SYS ...